chance to actually terminate the audit service and exit. Otherwise, on
an rc.d/auditd restart, the new audit daemon instance may try to start
auditing while the previous session is still running. Likewise, this
ensures a chance for auditd to terminate the audit trail at system
shutdown.
Perhaps more ideally, the script would wait synchronously for auditd to
exit rather than for an arbitrary but short period of time.
MFC after: 3 days
Obtained from: TrustedBSD Project
interface is an IPv6 interface.
Use this method to decide if we should attempt to configure an interface
with an IPv6 address in pccard_ether. The mechanism pccard_ether uses
to do this is unsuited to the task because it assumes the list of
interfaces it is passed is the full list of IPv6 interfaces and makes
decissions based on that. This is at least a step in the right
direction and is probably about as much as we can MFC safely.
PR: conf/103428
MFC after: 3 days
- Note that diskless_remount files may use ".." to support mounts above
the root path.
- Copy dot files when populating directories from /conf. [1]
PR: misc/102724 [1]
Submitted by: Attila Nagy <bra at fsn.hu> [1]
certain conditions. I haven't been able to find a better solution yet:
- Set a two read-only variables (${prefix} and ${etcdir}). This is
especially useful when using /etc/rc.d scripts with third-party
software installed from ports.
- Fix rc.d/sshd to work with openssh from ports using ${etcdir}
instead of hardcoded /etc.
- Reflect prefix/etcdir changes in rc.subr.8.
src/etc/rc.d/sshd: rev 1.9 -> 1.10
src/etc/rc.subr: rev 1.51 -> 1.52
src/share/man/man8/rc.subr.8: rev 1.11 -> 1.12
Approved by: cperciva (mentor)
it limits the width of its output to the value of $COLUMNS, or
what TIOCGWINSZ reports, or 79 columns. We should specify -ww
to ps(1) so that it removes the limit and prints lines in full.
Otherwise very long command pathnames could be mishandled, e.g.,
by _find_processes().
MFC after: 1 week
despite the interface link status.
Add dhclient_flags_iface and background_dhclient_iface rc.conf options.
(where iface is a specific interface). These can be used to give
interface specific flags to dhclient.
Reviewed by: brooks@
The order in _doit must be "nice su", not "su nice", for that.
In addition, don't ignore the exit status from "cd $foo_chdir".
Reviewed by: freebsd-rc (silence)
MFC after: 1 week
touch interfaces that don't actually exist in the stop case. In the
process move some IPv4 specific code from ifconfig_down to ipv4_down.
This should solve problems with ifconfig: error messages on boot when
interfaces are renamed.
thing to do in most (all?) cases and certainly should not be the default
now that we're running pccard_ether on all interface creates and
destroys.
MFC after: 3 days
and so users get hangs until interrupts are generated another way. We'll
have to find a way to make the 2 work together before re-enabling this by
default.
PowerPC-based Apple's machines and small utility to do it from
userland modelled after the similar utility in Darwin/OSX.
Only tested on 1.25GHz G4 Mac Mini.
MFC after: 1 month
and replace it with a new ntpdate_config variable.
- Document it in defaults/rc.conf and rc.conf.5.
- Document ntpdate_hosts in defaults/rc.conf.
Requested by: Chris Timmons <cwt@networks.cwu.edu>
Approved by: cperciva (mentor, implicit)
MFC after: 1 week
not be mounted unless the -l flag was specified.
Add an rc script, mountlate, which basically runs 'mount -a -l'. It runs
after DAEMON but before LOGIN.
This is useful for things like loopback mounts, because mountcritremote
runs before mountd / nfsd (since /usr might be a remote file system), so
an attempt to mount a loopback network file system in mountcritremote will
fail.
Also add a progress message to mountcritlocal, for the sake of symmetry
with similar messages in mountcritremote and mountlate.
Reviewed by: freebsd-rc
MFC after: 3 weeks
expect to see quite a few files appearing in libdata/ldconfig directories.
This change avoids the screen to be filled with the names of those ldconfig
files and replace them by the actual non-default directories they contain.
Most of them will be ${PREFIX}/lib so, 'sort -u' will help reducing the
output.
Approved by: cperciva (implicit)
MFC after: 1 week
of them do that conditionally depending on kldstat. The code is
duplicated all over, but bugs can be uniqie.
To make the things more consistent, introduce a new rc.subr function,
load_kld, which takes care of loading a kernel module conditionally.
(Found this lying for a while in my p4 branch for various hacks.)
automaticly add it to an Ethernet bridge. This is intended for applications
such as qemu, vmware, openvpn, ... which open tap interfaces and need them
bridged with the hosts network adapter, the user can set up a glob for
interfaces to be automatically added (eg tap*).
notification so all interfaces including pseudo are reported. When netif
creates the clones at startup devctl_disable has not been turned off yet so the
interfaces will not be initialised twice, enforce this by adding an explicit
order between rc.d/netif and rc.d/devd.
This change allows actions to taken in userland when an interface is cloned
and the pseudo interface will be automatically configured if a ifconfig_<int>=""
line exists in rc.conf.
Reviewed by: brooks
No objections on: net
1,2 and so on.
It specifies the command to be run as Nth after jail startup.
sh(1)-fu by: Dario Freni
PR: conf/97697
MFC after: 2 weeks
Reviewed by: ru@ (man page)
more appropriate value and is also the default set by the kernel. I
could not find a justification of why rc.conf began overriding it back
in 1998.
This dramatically cuts NFS traffic on e.g. a busy system with NFS root.
Reviewed by: mohans
MFC After: 2 weeks
scripts. These scripts handle vnode backed md(4) devices.
Old ramdisk{,-own} scripts will stay a bit in CVS to allow some time for
migration since variable names have changed (ramdisk_* -> mdconfig_*).
Two new variables have been introduced to be able to populate the md(4)
device once it has been mounted (mdconfig_*_files and mdconfig_*_cmd).
Use should be as easy as:
mdconfig_md0="-t malloc -s 10m"
mdconfig_md1="-t vnode -f /var/foo.img"
See rc.conf(5) for more information and description of the additional
variables.
Approved by: cperciva
issue where some global jail_* variables were overriden in the script. [1]
- Change "jid" to "jname" in rc.conf(5), since it's more a jail name than a
jail id. [1]
- Update examples and comments in defaults/rc.conf to advertise new
variables and the fact that some of the jail-specific variables may be made
jail-global. [2]
Reported by: pjd [1], clsung [2]
Approved by: cperciva
X-MFC after: i got sufficient testing from people using rc.d/jail
subdirectories that will be used for removable media mount points (i.e.
mount points for CDs, floppy disks, USB drives, etc.). While the primary
purpose of /media is to provide a location for HAL
(http://www.freedesktop.org/wiki/Software_2fhal) to mount volumes, it could
be used by any application that needs to manage removable media volumes.
Discussed on: arch@
Approved by: mux
MFC after: 1 week
boot. Autogeneration of nsswitch.conf doesn't makes sense in 7.0
since it's not permitted to upgrade from a pre-nss release without
passing through an intermediate release.
Suggested by: brooks
for some early starting services from the ports collection
to have their shared objects available before start.
Reviewed by: freebsd-rc (dougb, brooks)
MFC After: 3 days
- Sync with latest version from NetBSD.
'In order to handle some perl scripts running as daemons, add a
pattern which also matches "`basename $interpreter`: $command" in the
ps listing.'
Approved by: cperciva (mentor)
Obtained from: NetBSD
MFC after: 1 week
from ports. The effect is that ldconfig is now started right after
mountcritremote. Everything else is left unchanged.
PR: conf/68916
Submitted by: JD Bronson <jd@aurora.org>
Approved by: cperciva (mentor)
MFC after: 1 week
working on.
1) Make it possible to configure interfaces with certain characters in
their names that aren't valid in shell variables. Currently supported
characters are ".-/+". They are converted into '_' characters.
2) Replace nearly all eval statements in network.subr with a new
function get_if_var which substitues an interface name (after the
translations above) for "IF" in a variable name.
3) Fix list_net_interfaces() in the nodhcp case.
4) Allow the administrator to specify if dhclient should be started
when /etc/rc.d/netif configures the interface or only by devd.
This can be set on both a per interface and system wide basis.
PR: conf/88974 [1,2], conf/92433 [1,2]
