- Decrease reseeding interval from every 64 to every 16384 runs
to reduce entropy usage.
- Add time based reseeding. (Every 5 minutes.)
- Throw away the first 256 words of output as suggested in
"Weaknesses in the Key Scheduling Algorithm of RC4."
Reviewed by: Mark Murray
MFC After: jkh says ok
for the device now (we should really just be parsing a passed-in resource
buffer).
Wrap long lines so this is (more) readable.
Support Address16 and Address32 resources, in the CONSUMER case.
Support DRQs so that we can handle ISA devices.
Support ExtendedIrqs (we ignore most of their attributes)
Add a placeholder device for system memory and system resources. This
takes the place of the nexus placeholder, which only attaches to ISA.
the ACPI module if the system apperars to be ACPI compliant.
This is an initial cut; the load should really be done by Forth support
code, and we should check both the BIOS build date and a blacklist.
o Unify <machine/endian.h>'s across all architectures.
o Make bswapXX() functions use a different spelling of u_int16_t and
friends to reduce namespace pollution. The bswapXX() functions
don't actually exist, but we'll probably import these at some
point. Atleast one driver (if_de) depends on bswapXX() for big
endian cases.
o Deprecate byteorder(3) prototypes from <sys/types.h>, these are
now prototyped indirectly in <arpa/inet.h>.
o Deprecate in_addr_t and in_port_t typedefs in <sys/types.h>, these
are now typedef'd in <arpa/inet.h>.
o Change byteorder(3) prototypes to use standards compliant uint32_t
(spelled __uint32_t to reduce namespace pollution).
o Document new preferred headers and standards compliance.
Discussed with: bde
PR: 29946
Reviewed by: bmilekic
new data is acknowledged, reset the dupacks to 0.
The problem was spotted when a connection had its send buffer full
because the congestion window was only 1 MSS and was not being incremented
because dupacks was not reset to 0.
Obtained from: Yahoo!
1. Correctly handle commands initiated by the adapter. These commands
are defered to a kthread responsible for their processing, then are
properly returned to the controller.
2. Add/remove disk devices when notified by the card that a container was
created/deleted/offline.
3. Implement crashdump functionality.
4. Support all ioctls needed for the management CLI to work. The linux
version of this app can be found at the Dell or HP website. A native
version will be forthcoming.
MFC-after: 4.4-RELEASE
Second, the TI 1130 need to have the PCI_INTR set, not cleared.
This gets Soren's machine working with NEWCARD again.
# The whole initialization is a mess and needs to be organized ala OLDCARD.
the cwd is looked up inside the kernel. The native getcwd() in libc
handles this in userland if __getcwd() fails.
Obtained from: NetBSD via OpenBSD
Tested by: Chris Casey <chriss@phys.ksu.edu>, Markus Holmberg <markush@acc.umu.se>
Reviewed by: Darrell Anderson <anderson@cs.duke.edu>
PR: kern/24315
pollution for non-POSIX.1e macros.
o Introduce CAP_UNITE(), CAP_NONZERO().
o Disable aspects of CAP_SETPCAP, which is Linux-specific (in particular,
remove it from CAP_ALL_ON).
o Improve commenting.
Submitted by: tmm
Obtained from: TrustedBSD Project
KINFO_BSDI_SYSINFO. This supposedly fixes Netscape 3.0.4 (bsdi binary)
on -current. (and is also applicable to RELENG_4)
PR: 25476
Submitted by: Philipp Mergenthaler <un1i@rz.uni-karlsruhe.de>
multiple times, others do. The last strategy, which was to assume
that already routed interrupts were good and just return them doesn't
work for some laptops. So, instead, we have a new strategy: we notice
that we have an interrupt that's already routed. We go ahead and try
to route it, none the less. We will assume that it is correctly
routed, even if the route fails. We still assume that other failures
in the bios32 call are because the interrupt is NOT routed.
Note: some laptops do not support the bios32 interface to PCI BIOS and
we need to call it via the INT 2A interface. That is another windmill
to till at later.
Also correct a minor typo and minor whitespace nits.
Strong MFC candidate.
dual function card. It needs pretty much the same flags as the 656C,
except that it seems to need both the INVERT_MII_PWR and INVERT_LED_PWR
flags set. Tested with cardbus in -current as of today.
Also added support for the 3c656, which looks to be the same as
the 656B, except it doesn't need the EEPROM_8BIT flag. I think. This
one is untested, but the added support should not break any of the
other cards.
to the application as a RST would, this way we're compatible with the most
applications.
MFC candidate.
Submitted by: Scott Renfro <scott@renfro.org>
Reviewed by: Mike Silbersack <silby@silby.com>
I already deleted it some time ago). This should fix problem people have with
unsefined reference to `MD_PRELOAD_COMPRESSED'.
Submitted by: Manfred Antar <null@pozo.com>
the chip can cause a PCI protocol violation in under certain scenarios.
The workaround is to rewrite the EEPROM to disable Dynamic Standby Mode.
Once the EEPROM is rewritten, the system needs to be rebooted in order
to pick up the new settings.
This has been tested on several ICH2/ICH2-M systems, found in 815E based
boards, and usually identified by the presence of the 82562 ET/EM PHY.
Thanks to: Mike Tansca, Paul Saab for samples of the problematic boards.
