clocked at 10x normal speed. That is, when you set it for 9600
baud, it actually does 96000 baud. In order to make it plug and
play with other serial ports, it has to have its clock rate
reduced by a factor of 10.
Discussed with: Marcel Moolenaar
MFC after: 2 weeks
so the index needs to be translated into an offset. While we
did add the offset (0x10), we forgot to account for the width.
Tested by: Thomas Vogt
MFC after: 3 days
o Properly use rman(9) to manage resources. This eliminates the
need to puc-specific hacks to rman. It also allows devinfo(8)
to be used to find out the specific assignment of resources to
serial/parallel ports.
o Compress the PCI device "database" by optimizing for the common
case and to use a procedural interface to handle the exceptions.
The procedural interface also generalizes the need to setup the
hardware (program chipsets, program clock frequencies).
o Eliminate the need for PUC_FASTINTR. Serdev devices are fast by
default and non-serdev devices are handled by the bus.
o Use the serdev I/F to collect interrupt status and to handle
interrupts across ports in priority order.
o Sync the PCI device configuration to include devices found in
NetBSD and not yet merged to FreeBSD.
o Add support for Quatech 2, 4 and 8 port UARTs.
o Add support for a couple dozen Timedia serial cards as found
in Linux.
transmitted bits was between 8.6180us and 8.6200us when we used a RCLK
of 16.500MHz. This is a little low (should be 8.6805us). This error
is exactly the error one would expect if it actually had a 16.384MHz
watch oscillator (as suggested by garrett) instead of using the PCI
RCLK. Assume that the pci clock therefore wasn't really used, but
instead the cheap 16.384MH watch quartz oscillator. This gives bits
in the 8.6800us to 8.6810us ranage, which matches theoretical.
Submitted by: garrett
time ago appears to be based not on the typical 1.8432MHz clock, or
the other more typical multiple of 8 of this (14.7456MHz), but instead
it appears to be 1/2 the PCI clock rate or 16.50000MHz. I'm not 100%
sure that this is right, but since I did the original entry, I'm going
to go ahead and modify it. With the 14.7456MHz value, I was getting
bits that were ~7.3us instead of ~8.6us like they are supposed to be.
My measuring gear for today is a stupid handheld scope with two
signficant digits. So I don't know if it is 33.000000/2 MHz or some
other value close to 16.5MHz, but 16.5MHz works well enough for me to
use a couple of different devices at 115200 baud, and is a nice even
multiple of a well known clock frequency...
16C950. Adding it here doesn't unlock any of the cool 16C950 features
(like the 128 byte fifo, the different prescalor, etc), but it does
seem to get it working for me in light testing.
Card Provided by: Ihsan Dogan
virtual COM port. This makes the use of the Dell OpenManage tools on FreeBSD
considerably easier, and is based on Chuck Cranor's original patch for 4.6.
Reviewed by: imp
Tested by: dpk at dpk dot net
MFC after: 1 week
to be the same as Boca Research Turbo Serial 654 (4 serial port).
While add the 8 port variants as well.
Submitted by: sten@blinkenlights.nl
PR: kern/75793
MFC after: 1 week
of the struct, so that a placeholder for it (or unportable C99
initializers) are not needed for entries that don't use it. Use a C99
initializer for the 1 entry that uses it. Removed 91 placeholders.
This also restores API compatibility with NetBSD and RELENG_4 for most
entries.
Removed the requirement for a particular subvendor/subproduct in
rev.1.26 (VScom PCI-800L card). While the BARs, etc., may depend on
the sub-ids, this is not known to be so, and I think it is better to
guess that they don't. The decision to check sub-id checks in this
file is apparently random; for VScom cards they were checked in 3 of
8 cases.
Reviewed by: timeout by committer (joerg) after 6 months
o Introduce PUC_PORT_TYPE_UART so that we can attach to uart(4),
o Introduce port sub-types (eg PUC_PORT_UART_NS8250, PUC_PORT_UART_Z8530)
to handle different hardware and determine resource sizes.
o Introduce two new IVARs: PUC_IVAR_SUBTYPE and PUC_IVAR_REGSHFT. Both
are used by uart(4) to get sufficient information to talk to the HW.
o Introduce PUC_FLAGS_ALTRES to tell puc(4) to try memory mapped I/O
if I/O port space cannot be allocated, or vice versa.
o Have ports of type PUC_PORT_TYPE_COM attach to uart(1) if attaching
to sio(4) fails (due to not having the sio driver).
o Put struct puc_device_description in struct puc_softc instead of
having a pointer to a device description in the softc. This allows
us to create device descriptions on the fly without having to use
malloc() or otherwise have them staticly defined.
o Move puc_find_description() from puc.c to puc_pci.c as it's specific
to PCI.
o Add EBUS and SBUS frontends for use on sparc64. Note that the P in
puc stands for PCI, so we kinda mess things up here. It's too soon
to worry about it though. We'll know what to do about it in time.
NOTE: This commit changes the behaviour of puc(4) to not quieten the
device probe and attach for child devices. The uart(4) driver provides
additional device description that is valuable to have.
CP-168U board. It initializes and attaches in the same way as the
older (but higher performance) C168H. The only difference is the
board ID, which is 0x1681.
PR: kern/53548
Submitted by: regnauld@catpipe.net
MFC after: 1 week
