In the fdt data we've written for ourselves, the interrupt properties
for GIC interrupts have just been a bare interrupt number. In standard
data that conforms to the published bindings, GIC interrupt properties
contain 3-tuples that describe the interrupt as shared vs private, the
interrupt number within the shared/private address space, and configuration
info such as level vs edge triggered.
The new gic_decode_fdt() function parses both types of data, based on the
#interrupt-cells property. Previously, each platform implemented a decode
routine and put a pointer to it into fdt_pic_table. Now they can just
list this function in their table instead if they use arm/gic.c.
memory ordering model allows writes to different devices to complete out
of order, leading to a situation where the write that clears an interrupt
source at a device can complete after a write that unmasks and EOIs the
interrupt at the interrupt controller, leading to a spurious re-interrupt.
This adds a generic barrier function specific to the needs of interrupt
controllers, and calls that function from the GIC and TI AINTC controllers.
There may still be other soc-specific controllers that need to make the call.
Reviewed by: cognet, Svatopluk Kraus <onwahe@gmail.com>
MFC after: 3 days
Add suport for setting triggering level and polarity in GIC.
New function pointer was added to nexus which corresponds
to the function which sets level/sense in the hardware (GIC).
Submitted by: Wojciech Macek <wma@semihalf.com>
Obtained from: Semihalf
Qualcomm Snapdragon S4 and Snapdragon 400/600/800 SoCs and has architectural
similarities to ARM Cortex-A15. As for development boards IFC6400 series embedded
boards from Inforce Computing uses Snapdragon S4 Pro/APQ8064.
Approved by: stas (mentor)
interrupt counts and names, by making the names into an array of fixed-length
strings that can be directly indexed. This eliminates extra memory accesses
on every interrupt to increment the counts.
As a side effect, it also fixes a bug that would corrupt the names data
if a name was longer than MAXCOMLEN, which led to incorrect vmstat -i output.
Approved by: cognet (mentor)
MSI are implemented via software interrupt. PCIe cards will write
into software interrupt register which will cause inbound shared
interrupt which will be interpreted as a MSI.
Obtained from: Marvell, Semihalf
- Add functions to calculate clocks instead using hardcoded values
- Update reset and timers functions
- Update number of interrupts
- Change name of platform from db88f78100 to db78460
- Correct DRAM size and PCI IRQ routing in dts file.
Obtained from: Semihalf
Cummulative patch of changes that are not vendor-specific:
- ARMv6 and ARMv7 architecture support
- ARM SMP support
- VFP/Neon support
- ARM Generic Interrupt Controller driver
- Simplification of startup code for all platforms
the implementation can guarantee forward progress in the event of
a stuck interrupt or interrupt storm. This is especially critical
for fast interrupt handlers, as they can cause a hard hang in that
case. When first called, arm_get_next_irq() is passed -1.
Obtained from: Juniper Networks, Inc.
o recognize ixp435 cpu
o change memory layout for for ixp4xx to not assume memory is aliases
to 0x10000000 (Cambria/ixp435 memory starts at zero)
o handle 64 irqs for ixp435
o dual EHCI USB 2.0 controller integral to ixp435
o overhaul NPE code for ixp435 and better MAC+MII naming
o updated NPE firmware (including NPE-A image for ixp435/ixp465)
o Gateworks Cambria board support:
- IDE compact flash
- MCU
- front panel LED on i2c bus
- Octal LED latch
Sanity-tested with NFS-root on Avila and Cambria boards. Requires
pending boot2 mods for CF-boot on Cambria.
* Orion
- 88F5181
- 88F5182
- 88F5281
* Kirkwood
- 88F6281
* Discovery
- MV78100
The above families of SOCs are built around CPU cores compliant with ARMv5TE
instruction set architecture definition. They share a number of integrated
peripherals. This commit brings support for the following basic elements:
* GPIO
* Interrupt controller
* L1, L2 cache
* Timers, watchdog, RTC
* TWSI (I2C)
* UART
Other peripherals drivers will be introduced separately.
Reviewed by: imp, marcel, stass (Thanks guys!)
Obtained from: Marvell, Semihalf
- Fix nexus_setup_intr() abuse of setting up multiple IRQs in one go. Calling
arm_setup_irqhandler() in loop is bogus, as there's just one cookie given
from the caller and it is overwritten in each iteration so that only the
last handler's cookie value prevails.
- Proper intr masking/unmasking handling: the IRQ source is masked at PIC level
only after the last handler has been removed from the list.
Reviewed by: cognet, imp, sam, stass
Obtained from: Grzegorz Bernacki gjb ! semihalf dot com
boards. This is enough to net-boot to multiuser.
Also supported is the SMSC LAN91C111 parts used on the netCF, netDUO and netMMC
add-on boards.
I'll be putting some instructions on how to boot this on the Gumstix boards
online soon.
This is still fairly rough and will be refined over time but I felt it was
better to get this out there where other people can help out.
interrupt. So, add a new function pointer, arm_post_filter, which defaults
to NULL, and which will be used as the post_filter arg for
intr_event_create(). Set it properly for the AT91, so that it boots again.
Reported by: hps
It only supports sa1110 (on simics) right now, but xscale support should come
soon.
Some of the initial work has been provided by :
Stephane Potvin <sepotvin at videotron.ca>
Most of this comes from NetBSD.
