taskqueued interrupt mode is going to be quite complex. Since
the polling mode is considered legacy feature for em(4) driver,
the decision is made to make polling and new interrupt handler
mutually exclusive, selected at compile time.
If kernel is compiled with DEVICE_POLLING, the fast taskqueued
interrupt handler code is disabled and the em_poll() and legacy
em_intr() functions are enabled. Otherwise, legacy functions
are disabled and only em_intr_fast() code is compiled.
Discussed with: scottl
- K&R -> ANSI prototype [O]
- Do not bother to do free right before exit() or execve() [O]
- Remove some dead code in addarg()
- Make additional parameters specified in mailer.conf(5)
actually work and document the fact. [N]
- Avoid using __progname but instead use getprogname()
and setprogname() to provide more sensible messages. [O, N]
- Update $OpenBSD$ and $NetBSD$ to reflect the fact that we
have sync'ed with their code.
- WARNS=6
Obtained from/Inspired by: OpenBSD [O], NetBSD [N] (partially)
Clean out the abortive start to homegrown, per-mpt,
Domain Validation. This should really be done at a
higher level.
Use the PIM_SEQSCAN flag for U320- this seems to correct
cases of being unable to consistently negotiate U320 in
the cases where I'd seen this before.
Between this and other recent checkins, this driver is
pretty close to being ready for MFC.
Reviewed by: scottl, ken, scsi@
MFC after: 1 week
what to do with it.
This forces us to scan targets sequentially, not in parallel.
The reason we might want to do this is that SPI negotiation
might not work right at the SIM level if we try to do it
in parallel. We *could* fix this for each SIM where this is
broken, but it's a lot harder to do that when we can simply
ask CAM to probe sequentially.
If PIM_SEQSCAN is not set (default), the original behaviour for
probing is unchanged.
LUN probing is still done in parallel for each target in either
case.
While we're at it, clean up some resource leakage for error
cases.
Reviewed by: ken, scott, scsi@
MFC after: 1 week
Now, encryption algorithm is given using '-e' option, not '-a'.
The '-a' option is now used to specify authentication algorithm.
Supported by: Wheel Sp. z o.o. (http://www.wheel.pl)
255.255.255.0, and a default route with gateway x.x.x.1. Now if
the address mask is changed to something more specific, e.g.,
255.255.255.128, then after the mask change the default gateway
is no longer reachable.
Since the default route is still present in the routing table,
when the output code tries to resolve the address of the default
gateway in function rt_check(), again, the default route will be
returned by rtalloc1(). Because the lock is currently held on the
rtentry structure, one more attempt to hold the lock will trigger
a crash due to "lock recursed on non-recursive mutex ..."
This is a general problem. The fix checks for the above condition
so that an existing route entry is not mistaken for a new cloned
route. Approriately, an ENETUNREACH error is returned back to the
caller
Approved by: andre
o define HAL_SOFTC, HAL_BUS_TAG, and HAL_BUS_HANDLE to be machine
independent; this fixes portability issues with bsd systems
o add ah_disable api for turning off operation of both MAC and PHY
o add ah_getAntennaSwitch and ah_setAntennaSwitch api's for better control
of antenna usage and diversity
o add ah_setAckCTSRate and ah_setAckCTSRate for controlling tx rate of
h/w generated frames
o add ah_setBeaconTimers api for simpler setting of the beacon timer registers
o remove ah_waitForBeaconDone api
o add HAL_TXDESC_DURENA flag to enable h/w duration setting in tx descriptor
o correct documentation of min/max tx power units (.5 dBm)
o switch arm, mips, and powerpc builds to use functions for register
read/write operations
o fix sparc builds to not reference %g2 and %g3 registers
o add public builds for SoC's
MFC after: 1 month
- Remove "device cryptodev" as it is not needed for compiling padlock(4)
into the kernel. Actually it is not advisable, because padlock
instructions can be used directly from userland, so passing the work
through the kernel is a bad idea.
with fast_ipsec(4) and geli(8) authentication (comming soon).
If consumer requests only for HMAC algorithm (without encryption), return
EINVAL.
- Add support for the CRD_F_KEY_EXPLICIT flag, for both encryption and
authentication.
process was sucessfully audited. Otherwise, generate the PID
token. This change covers the pid < 0 cases, and pid lookup
failure cases.
Submitted by: wsalamon
Obtained from: TrustedBSD Project
