o Make the pfsync.ko actually usable. Before this change loading it
didn't register protosw, so was a nop. However, a module /boot/kernel
did confused users.
o Rewrite the way we are joining multicast group:
- Move multicast initialization/destruction to separate functions.
- Don't allocate memory if we aren't going to join a multicast group.
- Use modern API for joining/leaving multicast group.
- Now the utterly wrong pfsync_ifdetach() isn't needed.
o Move module initialization from SYSINIT(9) to moduledata_t method.
o Refuse to unload module, unless asked forcibly.
o Improve a bit some FreeBSD porting code:
- Use separate malloc type.
- Simplify swi sheduling.
This change is probably wrong from VIMAGE viewpoint, however pfsync
wasn't VIMAGE-correct before this change, too.
Glanced at by: bz
with FreeBSD easier for vendors.
- For optional files use variables starting with underscore.
Both changes make rc.d/Makefile look similar to sys/modules/Makefile.
Reviewed by: dim
the /etc/rc.d/nfsd script sets vfs.nfsd.server_max_nfsvers to 3.
Then, when you set nfsv4_server_enable=YES in rc.conf, and restart nfsd
via the rc.d script, without rebooting, the sysctl does *not* get reset
to max version 4, so NFSv4 still doesn't work.
Fix this by explicitly setting vfs.nfsd.server_max_nfsvers to 4 when
NFSv4 is requested.
I also added resetting of the nfs_privport sysctls, since this has the
same issue: nfs_reserved_port_only=YES in rc.conf sets the nfs_privport
sysctl to 1, but in the other case, the sysctl doesn't get reset to 0.
Reviewed by: rmacklem
Silence from: rc@
MFC after: 3 days
Variable 'rc_force' is accessible only at the time of rc_run_command,
so it can't be examined from the script's main code.
Spotted by: hrs
Reviewed by: hrs, des
Approved by: des
MFC after: 2 weeks
Make sure that static ARP and NDP bindings are set before NETWORKING.
As static_ndp is based on static_arp, pass copyright to the project with
permission of the original author (delphij@).
Reviewed by: delphij@FreeBSD.org
MFC after: 3 days
for interfaces which were not configured for DHCP *unless* rc_force was set;
the correct logic is to run dhclient for those interfaces *only if* rc_force
is set.
Broken by: des@
Noticed by: everybody and his dog
Submitted by: rea@
PR: bin/161733
(r225485). When setting an interface name to it, the following
configurations will be enabled:
1. "no_radr" is set to all IPv6 interfaces automatically.
2. "-no_radr accept_rtadv" will be set only for $ipv6_cpe_wanif. This is
done just before evaluating $ifconfig_IF_ipv6 in the rc.d scripts (this
means you can manually supersede this configuration if necessary).
3. The node will add RA-sending routers to the default router list
even if net.inet6.ip6.forwarding=1.
This mode is added to conform to RFC 6204 (a router which connects
the end-user network to a service provider network). To enable
packet forwarding, you still need to set ipv6_gateway_enable=YES.
Note that accepting router entries into the default router list when
packet forwarding capability and a routing daemon are enabled can
result in messing up the routing table. To minimize such unexpected
behaviors, "no_radr" is set on all interfaces but $ipv6_cpe_wanif.
Approved by: re (bz)
Print a separate "Additional routing options" line for each address family
which has additional options, so that it does not get mixed up with the
output from adding routes.
This also reverts r224048 which added newlines to two arbitrary routing
options.
longer used by /etc/rc.d/nfsd and it is no longer necessary
to load the old nfs server by default, when nfs_server_enable="YES".
Tested by: sgk at troutmask.apl.washington.edu
Reviewed by: rc (Andrzej Tobola)
can use the "-o" option to force the old NFS server to run.
Running the old NFS server is enabled by setting
oldnfs_server_enable="YES". The scripts will only enable
providing service for NFSv4 if nfsv4_server_enable="YES"
is set.
Reviewed by: dougb (rc)
times mount is called.
Limit the automatic behavior to when AUTO is specified (as it is in
etc/defaults/rc.conf) and for everything else take advantage of all
of the goodness in checkyesno.
like, determines the path to a pid file as it is specified in a conf file.
Use the new feature for rc.d/named and rc.d/devd, the 2 services in the
base that list their pid files in their conf files.
Remove the now-obsolete named_pidfile, and warn users if they have it set.
The old version had a race between the time that the old file was
cp'ed to acct.0 and the time that 'sa -s' was run that prevented
the commands that occurred in the meantime from being backed up.
It's also arguable that the old version was inefficient in using
cp which can be a problem on a space-constrained system.
This version avoids both problems, albeit it's considerably more
complicated. The advantage of putting the log rotation in the rc.d
script is that it can handle the _enable and _file questions without
having to do gymnastics to discover either value in the periodic script.
As a side effect of reviewing the rc.d script I cleaned it up a bit.
While I'm here, don't run the sysctl frob unconditionally, and
s/sysctl/$SYSCTL/
PR: conf/153460 [1]
Submitted by: Grigory Rechistov <ggg_mail@inbox.ru>
