slice, partition, newfs, and install FreeBSD from a tarball on a remote server.
Handy for doing mass-installs for server farms.
Documentation following shortly.
for the AN985 "Centaur" chip, which is apparently the next genetation
of the "Comet." The AN985 is also a tulip clone and is similar to the
AL981 except that it uses a 99C66 EEPROM and a serial MII interface
(instead of direct access to the PHY registers).
Also updated various documentation to mention the AN985 and created
a loadable module.
I don't think there are any cards that use this chip on the market yet:
the datasheet I got from ADMtek has boxes with big X's in them where the
diagrams should be, and the sample boards I got have chips without any
artwork on them.
made only the most superficial changes so far to HARDWARE.TXT and
eliminated the stuff I absolutely knew didn't work. That still leaves
a lot of work to do and this is mostly just a place-holder for now.
the Davicom DM9100 and DM9102 chipsets, including the Jaton Corporation
XPressNet. Datasheet is available from www.davicom8.com.
The DM910x chips are still more tulip clones. The API is reproduced
pretty faithfully, unfortunately the performance is pretty bad. The
transmitter seems to have a lot of problems DMAing multi-fragment
packets. The only way to make it work reliably is to coalesce transmitted
packets into a single contiguous buffer. The Linux driver (written by
Davicom) actually does something similar to this. I can't recomment this
NIC as anything more than a "connectivity solution."
This driver uses newbus and miibus and is supported on both i386
and alpha platforms.
SiS 900 and SiS 7016 PCI fast ethernet chipsets. Full manuals for the
SiS chips can be found at www.sis.com.tw.
This is a fairly simple chipset. The receiver uses a 128-bit multicast
hash table and single perfect entry for the station address. Transmit and
receive DMA and FIFO thresholds are easily tuneable. Documentation is
pretty decent and performance is not bad, even on my crufty 486. This
driver uses newbus and miibus and is supported on both the i386 and
alpha architectures.
I backed-out the changes in -current and didn't touch stable at all (I
thought I had my patch order reversed, not what actually happened).
AIEEE! I can't even blame the crack for this one since I broke my
crack pipe a few weeks ago. I think sleep deprivation gets the blame
for this one.
Medal for noticing this one goes to: Jim Bloom <bloom@acm.org>
bringing in DHCP support. The only thing I left out were Poul-Henning's
newfs changes since I'm not sure if he's brought the rest of that support
into -stable yet. If it turns out that this is the case, I'll MFC those
changes too.
Set ALLLANG to install all the languages, otherwise set DOC_LANG
to just the languages (and encodings) you want to install.
Default to building the html-split (lots of small HTML files, with
links to go between them), html (one big honking HTML file), and plain
text versions of the documentation. Does not compress any of the docs
prior to doing the installation.
Testing and feedback: Jack O'Neill <jack@germanium.xtalwind.net>,
Cockups and typos: nik
. Now builds on -STABLE (-CURRENT is broken due to bugs)
. etc directory contents centralized instead of in each
type directory (can exclude & override as desired)
. Removed extraneous language files (lang files for rc really necessary?)
. dialog-based build tool with support for custom floppy builds
. MFS image loads as a mfs_root module instead of compiled into kernel
THIS IS BROKEN ON CURRENT. I'll MFC to -STABLE immediately following.
luigi tells me I have an OK from jkh on the MFC.
Submitted by: luigi
PCI fast ethernet controller. Currently, the only card I know that uses
this chip is the D-Link DFE-550TX. (Don't ask me where to buy these: the
only cards I have are samples sent to me by D-Link.)
This driver is the first to make use of the miibus code once I'm sure
it all works together nicely, I'll start converting the other drivers.
The Sundance chip is a clone of the 3Com 3c90x Etherlink XL design
only with its own register layout. Support is provided for ifmedia,
hardware multicast filtering, bridging and promiscuous mode.
in a previous FreeBSD version. That never happened. Document that
it is due to be replaced, but leave it open-ended as to when.
Also do some mdoc cleanup.
PR: docs/13148
PR: docs/13144
Submitted by: Lee Cremeans <lcremeans@erols.com>
Alex M. Zelkim <phantom@cris.net>
Discussed with: jkh
Originally submitted by: Wayne Self <wself@cdrom.com>
Allow a ppp startup option in rc.conf.
Adjust sysinstall so that it appends to the end of ppp.conf
and uses the generated profile to start ppp in auto mode on
boot.
Submitted by: Josef L. Karthauser <joe@uk.FreeBSD.org>
ethernet controllers based on the AIC-6915 "Starfire" controller chip.
There are single port, dual port and quad port cards, plus one 100baseFX
card. All are 64-bit PCI devices, except one single port model.
The Starfire would be a very nice chip were it not for the fact that
receive buffers have to be longword aligned. This requires buffer
copying in order to achieve proper payload alignment on the alpha.
Payload alignment is enforced on both the alpha and x86 platforms.
The Starfire has several different DMA descriptor formats and transfer
mechanisms. This driver uses frame descriptors for transmission which
can address up to 14 packet fragments, and a single fragment descriptor
for receive. It also uses the producer/consumer model and completion
queues for both transmit and receive. The transmit ring has 128
descriptors and the receive ring has 256.
This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus
so that it can be compiled as a loadable kernel module. Support for BPF
and hardware multicast filtering is included.
ifconfig, essentially stealing the lease until the user goes and changes
it. The alternative, sadly, is total dysfunction since bpf isn't in
GENERIC and network connectivity would otherwise fail completely on first
bootup when DHCP configuration was attempted again.
The ultimate answer here is to make either bpf a loadable kernel module
(which security conscious admins will be able to simply remove from /modules)
or come up with a lighter weight mechanism just for dhcp and other apps that
need to see broadcast packets but not otherwise sniff the wire in full
bpf glory.
in some code from C. Stone to parse the lease information. This is still
a WIP and this commit is largely intended to allow others to sync up; the
dhclient code still only works when doing dhcp configuration post-install
and requires a bit more work on the boot floppy before it will truly
work in the minimal bootstrapping role.
gigabit ethernet adapters. This includes two single port cards
(single mode and multimode fiber) and two dual port cards (also single
mode and multimode fiber). SysKonnect is currently the only
vendor with a dual port gigabit ethernet NIC.
The ports on dual port adapters are treated as separate network
interfaces. Thus, if you have an SK-9844 dual port SX card, you
should have both sk0 and sk1 interfaces attached. Dual port cards
are implemented using two XMAC II chips connected to a single
SysKonnect GEnesis controller. Hence, dual port cards are really
one PCI device, as opposed to two separate PCI devices connected
through a PCI to PCI bridge. Note that SysKonnect's drivers use
the two ports for failover purposes rather that as two separate
interfaces, plus they don't support jumbo frames. This applies to
their Linux driver too. :)
Support is provided for hardware multicast filtering, BPF and
jumbo frames. The SysKonnect cards support TCP checksum offload
however this feature is not currently enabled (hopefully it will
be once we get checksum offload support).
There are still a few things that need to be implemeted, like
the ability to communicate with the on-board LM80 voltage/temperature
monitor, but I wanted to get the driver under CVS control and into
-current so people could bang on it.
A big thanks for SysKonnect for making all their programming info
for these cards (and for their FDDI and token ring cards) available
without NDA (see www.syskonnect.com).
