Add debug.sizeof.g_stat sysctl.
Set the id field of the g_stat when we create consumers and providers.
Remove biocount from consumer, we will use the counters in the g_stat
structure instead. Replace one field which will need to be atomically
manipulated with two fields which will not (stat.nop and stat.nend).
Change add companion field to bio_children: bio_inbed for the exact
same reason.
Don't output the biocount in the confdot output.
Fix KASSERT in g_io_request().
Add sysctl kern.geom.collectstats defaulting to off.
Collect the following raw statistics conditioned on this sysctl:
for each consumer and provider {
total number of operations started.
total number of operations completed.
time last operation completed.
sum of idle-time.
for each of BIO_READ, BIO_WRITE and BIO_DELETE {
number of operations completed.
number of bytes completed.
number of ENOMEM errors.
number of other errors.
sum of transaction time.
}
}
API for getting hold of these statistics data not included yet.
handy if the machine is on another floor. A minor issue with this is that
these functions are also used by the debugger, so its possible to break into
the debugger from the debugger.
PR: sparc64/47143
Reviewed by: benno
Approved by: jake (mentor)
correctly tell CAM to requeue the command and then freeze it's queue. The
problem was that when resources became available again, it wouldn't tell
CAM to unfreeze it's queue, so no more commands would ever be delivered.
This is simialr to the bug that was fixed in the cciss driver last year.
This is a bug in 4-STABLE also, but is probably masked by the OS being
fast enough to drain the completion queue before it fills up.
Also add some diagnostics avaialble when compiled with MLY_DEBUG.
Thanks very much to LSI Corp for donating equipment to track this down,
and Vaidus Damosevicius for pestering me long enough to get it fixed.
We may actually be increasing Giant contention doing so because the
actual stuff we do is very cheap.
Also I am not convinced there is not a tiny window for a race here.
Sync with userland test framework which now deals better with pcm feeder kobj
emulation.
Reduce max rate from 96kHz to 48kHz as userland tests found a few bad
points about 90kHz and we don't care about operating up there for now.
DDB when the interrupt button (aka the "programmer's switch") is pressed.
This isn't unfortunately an NMI, but it's a handy way to get into DDB
quickly if needed.
- Move the command timeout check from a separate repeating timeout to the
kthread since the kthread is already running periodically.
- Move printing the hardware print buffer to the kthread.
- Properly shut down the kernel thread on detach.
- Detach the child array devices on detach.
- Don't issue a controller halt command on detach. Doing so requires a PCI
reset to wake the controller back up. The driver can now be unloaded as
long as CAM support is not enabled.
similar patch has been in 4.x for a while, but is more hacky there.)
For this to work, vinum has to be loaded early (e. g. from
boot/loader), for obvious reasons. If the kernel env variable
(aka. loader variable) "vinum.autostart" is set, vinum then asks the
sysctl kern.disks for all available disks in the system, and scans
them for possible vinum headers.
For statically compiled kernels, this behaviour can be obtained even
without boot/loader by using "options VINUM_AUTOSTART" (though this is
not the recommended way).
Alternatively, the 4.x way to specify "vinum.drives" is also supported.
No further hacks (like the 4.x "vinum.root" variable) are needed,
since in 5.x, mountroot() asks back at the drivers to have them
resolve the name of the root FS into a dev_t (using the dev_clone
eventhandler).
(The MFC reminder below is for a partial MFC for vinum.autostart, the
rest is already there in 4.x.)
Timed out on: grog
MFC after: 2 weeks
we have the rc4 code already in the kernel (via wlan stuff or awi).
Add a dependency on the rc4 module so if it doesn't exist then load it.
Reviewed by: archie