- Add a note to the ipfw(8) man page about the rules no longer being
case sensitive.
- Fix some typos in the man page.
PR: docs/164772
Reviewed by: bz
Approved by: gabor (doc mentor, src committer)
MFC after: 2 weeks
The RX EDMA support requires a modified approach to the RX descriptor
handling.
Specifically:
* There's now two RX queues - high and low priority;
* The RX queues are implemented as FIFOs; they're now an array of pointers
to buffers;
* .. and the RX buffer and descriptor are in the same "buffer", rather than
being separate.
So to that end, this commit abstracts out most of the RX related functions
from the bulk of the driver. Notably, the RX DMA/buffer allocation isn't
updated, primarily because I haven't yet fleshed out what it should look
like.
Whilst I'm here, create a set of matching but mostly unimplemented EDMA
stubs.
Tested:
* AR9280, station mode
TODO:
* Thorough AP and other mode testing for non-EDMA chips;
* Figure out how to allocate RX buffers suitable for RX EDMA, including
correctly setting the mbuf length to compensate for the RX descriptor
and completion status area.
This driver does not yet handle multiple chip selects properly.
Note that the NAND infrastructure does not perform full page
reads or writes, which means that this driver cannot make use
of the hardware ECC that is otherwise present.
o Save and clear the LTESR register in the interrupt handler.
o In lbc_read_reg(), return the saved LTESR register value if applicable
(i.e. when the saved value is not invalid (read: ~0U)).
o In lbc_write_reg(), clear the bits in the saved register when when it's
written to and when the asved value is not invalid.
o Also in lbc_write_reg(), the LTESR register is unlocked (in H/W) when
bit 1 of LTEATR is cleared. We use this to invalidate our saved LTESR
register value. Subsequent reads and write go to H/W directly.
While here:
o In lbc_read_reg() & lbc_write_reg(), add some belts and suspenders to
catch when register offsets are out of range.
o In lbc_attach(), initialize completely and don't leave something left
for lbc_banks_enable().
of interrupts of direct children. Have the bus_config_intr and
bus_teardown_intr methods implemented by bus_generic_config_intr and
bus_generic_teardown_intr (resp) as we don't need to do anything
special outselves.
This removes all the ``#ifdef $arch'' code that was there because powerpc
didn't have a proper nexus and people tend to copy and paste stuff.
methods so that MI drvers can depend on us doing the right thing instead
of having to go around us and call MD code directly. See the FDT code for
example (not for long though).
the aggressive pattern matching of the :C modifier. I tested build and
install in 2 phases, however with different solutions, resulting in the
breakage. Mea culpa.
The solution is to break out the all: target. This causes a few lines of
code duplication, but now the all: target works as it should, and the
other targets continue to work as they did before.
While I'm here, add a ===> header line to the start of each port build
to make it easier to find/more clear in the logs.
Note that setting the PTE_MODIFIED bit based on whether write is possible
is incorrect. We should set PTE_MODIFIED based on whether the access
is a write operation.
now fully encapsulates all accesses to f_offset, and extends f_offset
locking to other consumers that need it, in particular, to lseek() and
variants of getdirentries().
Ensure that on 32bit architectures f_offset, which is 64bit quantity,
always read and written under the mtxpool protection. This fixes
apparently easy to trigger race when parallel lseek()s or lseek() and
read/write could destroy file offset.
The already broken ABI emulations, including iBCS and SysV, are not
converted (yet).
Tested by: pho
No objections from: jhb
MFC after: 3 weeks
names to shorten them. PulseAudio reported to have problems with names
longer then 63 chars and at least in XMMS long names are inconvinient.
Reported by: hselasky
MFC after: 3 days
Adjust power_profile script to handle the new world order as well.
Some vendors are opting out of a C2 state and only defining C1 & C3. This
leads the acpi_cpu display to indicate that the machine supports C1 & C2
which is caused by the (mis)use of the index of the cx_state array as the
ACPI_STATE_CX value.
e.g. the code was pretending that cx_state[i] would
always convert to i by subtracting 1.
cx_state[2] == ACPI_STATE_C3
cx_state[1] == ACPI_STATE_C2
cx_state[0] == ACPI_STATE_C1
however, on certain machines this would lead to
cx_state[1] == ACPI_STATE_C3
cx_state[0] == ACPI_STATE_C1
This didn't break anything but led to a display of:
* dev.cpu.0.cx_supported: C1/1 C2/96
Instead of
* dev.cpu.0.cx_supported: C1/1 C3/96
MFC after: 2 weeks
bwrite(). VFS needs to know about EFAULT from uiomove() and does not
care much that partially filled block writeback after EFAULT was
successfull. Early return without error causes short write to be
reported to usermode.
Reported and tested by: andreast
MFC after: 3 weeks
Asus laptops. It is alike to acpi_asus(4), but uses WMI interface instead
of separate ACPI device.
On Asus EeePC T101MT netbook it allows to handle hotkeys and on/off WLAN,
Bluetooth, LCD backlight, camera, cardreader and touchpad.
On Asus UX31A ultrabook it allows to handle hotkeys, on/off WLAN, Bluetooth,
Wireless LED, control keyboard backlight brightness, monitor temperature
and fan speed. LCD brightness control doesn't work now for unknown reason,
possibly requiring some video card initialization.
Sponsored by: iXsystems, Inc.
important for those that use -DNO_CLEAN routinely, since it will prevent
installing stale stuff, and even more important when the port is upgraded
to a newer version. When the user doesn't use -DNO_CLEAN, this will create
an infinitesimal amount of extra work, but won't hurt anything.
This is necessary because the ports tree has flags that prevent the ususal
'update the build if newer source files exist' logic from doing what it
would do in the base.
as an EDMA check function.
For the AR9003 and later NICs, different TX/RX DMA and descriptor handling
code will be conditional on the EDMA check.
Obtained from: Qualcomm Atheros
we need to pass BIO_DELETE requests down to providers that support
it. Also, we need to announce our support for BIO_DELETE to upper
consumer. This requires:
- In g_mirror_start() return true for "GEOM::candelete" request.
- In g_mirror_init_disk() probe below provider for "GEOM::candelete"
attribute, and mark disk with a flag if it does support BIO_DELETE.
- In g_mirror_register_request() distribute BIO_DELETE requests only
to those disks, that do support it.
Note that we announce "GEOM::candelete" as true unconditionally of
whether we have TRIM-capable media down below or not. This is made
intentionally, because upper consumer (usually UFS) requests the
attribite only once at mount time. And if user ever migrates his
mirror from HDDs to SSDs, then he/she would get TRIM working without
remounting filesystem.
Reviewed by: pjd
running with multiple SoCs compiled in very well anyway, so this just
wastes space. As more and more SoCs arrive in the tree, it is better
to edit one master file that builds them all than many board files.
* Add a new ANI variable, for AR9003 and later chips;
* The AR9003 and later series chips support two RX queues now, so start
down the road of supporting that;
* Add some new TX queue types - uAPSD is possible on earlier chips,
but PAPRD is relevant to AR9003 and later.
Obtained from: Qualcomm Atheros, Linux ath9k
recent regression with ULE, causing processes to get stuck in getblk
as well as interrupt handler execution delays to rise above the command
timeout of mpt(4).
MFC after: 3 days
at the point that it calls get_pv_entry(). Thus, pmap_enter()'s PV list
lock pointer must be passed to get_pv_entry() for those rare occasions
when get_pv_entry() calls reclaim_pv_chunk().
Update some related comments.
across in_gif_output() and in6_gif_output() anyway, and once it is held
across those it might as well be held for the entire loop. This simplifies
the code and removes the need for the custom IFF_GIF_WANTED flag (which
belonged in the softc and not as an IFF_* flag anyway).
Tested by: Vincent Hoffman vince unsane co uk
According to the AMD manual the whole range from 0x09 to 0x1f are NOPs.
Intel manual mentions only 0x1f. Use only Intel one for now, it seems
to be the one actually generated by compilers.
Use gdb mnemonic for the operation: "nopw".
[1] AMD64 Architecture Programmer's Manual
Volume 3: General-Purpose and System Instructions
[2] Software Optimization Guide for AMD Family 10h Processors
[3] Intel(R) 64 and IA-32 Architectures Software Developer’s Manual
Volume 2 (2A, 2B & 2C): Instruction Set Reference, A-Z
Tested by: Fabian Keil <freebsd-listen@fabiankeil.de> (earlier version)
MFC after: 3 days
relative to the start address (unless the start address is 0, which is
not the case).
This is currently not a problem because all powerpc architectures are
using loader(8) which passes metadata to the kernel including the
correct `endkernel' address. If we don't use loader(8), register 4
and 5 will have the size of the kernel ELF file, not its end address.
We fix that simply by adding `kernel_text' to `end' to compute
`endkernel'.
Discussed with: nathanw
On systems with HZ=100 it caused Intel eDP video output initialization
(and Xorg startup) to take several minutes instead of several seconds.
Reviewed by: kib
MFC after: 3 days
a CD or DVD drive with a damaged disc often benefit from a shorter
timeout. Also, when retries are set to 0, an application is expecting
errors and recovering them so do not print the error into the log.
The number of expected errors can literally be in the hundreds of
thousands which significantly slows data recovery.
Reviewed by: ken@ (but quite some time ago).
14.00.00.01-fbsd.
Their description of the changes is as follows:
1. Copyright contents has been changed in all respective .c
and .h files
2. Support for WRITE12 and READ12 for direct-io (warpdrive only)
has been added.
3. Driver has added checks to see if Drive has READ_CAP_16
support before sending it down to the device.
If SPC3_SID_PROTECT flag is set in the inquiry data, the
device supports protection information, and must support
the 16 byte read capacity command, otherwise continue without
sending read cap 16. This will optimize driver performance,
since it will not send READ_CAP_16 to the drive which does
not have support of READ_CAP_16.
4. With new approach, "MPTIOCTL_RESET_ADAPTER" IOCTL will not
use DELAY() which is busy loop implementation.
It will use <msleep> (Better way to sleep without busy
loop). Also from the HBA reset code path and some other
places, DELAY() is replaced with msleep() or "pause()",
which is based on sleep/wakeup style calls. Driver use
msleep()/pause() instead of DELAY based on CAN_SLEEP/NO_SLEEP
flags to avoid busy loop which is not required all the
time.e.a
a. While driver is getting loaded, driver calls most of the
commands with NO_SLEEP.
b. When Driver is functional and it needs Reinit of HBA,
CAN_SLEEP flag is used.
5. <mpslsi> driver is not Endian safe. It will not work on Big
Endian machines like Sparc and PowerPC platforms because it
assumes it is running on a Little Endian machine.
Driver code is modified such way that it does not assume CPU
arch is Little Endian.
a. All places where Driver interacts from HBA to Host, it
converts Little Endian format to CPU format.
b. All places where Driver interacts from Host to HBA, it
converts CPU format to Little Endian.
6. Findout memory leaks in FreeBSD Driver and resolve those,
such as memory leak in targ's luns creation/deletion.
Also added additional checks to see memory allocation
success/fail.
7. Add loginfo prints as debug message, i.e. When FW sends any
loginfo, Driver should print those as debug message.
This will help for debugging purpose.
8. There is possibility to get config request timeout. Current
driver is able to detect config request timetout, but it does
not do anything on config_request timeout. Driver should
call mps_reinit() if any request_poll (which is called as
part of config_request) is time out.
9. cdb length check is required for 32 byte CDB. Add correct mpi
control value for 32 bit CDB as below while submitting SCSI IO
Request to controller.
mpi_control |= 4 << MPI2_SCSIIO_CONTROL_ADDCDBLEN_SHIFT;
10. Check the actual status of Message unit reset
(mps_message_unit_reset).Previously FreeBSD Driver just writes
MPI2_FUNCTION_IOC_MESSAGE_UNIT_RESET and never check the ack
(it just wait for 50 millisecond). So, Driver now check the
status of "MPI2_FUNCTION_IOC_MESSAGE_UNIT_RESET" after writing
it to the FW.
Now it also checking for whether doorbell ack uses msleep with
proper sleep flags, instead of <DELAY>.
11. Previously CAM does not detect Multi-Lun Devices. In order to
detect Multi-Lun Devices by CAM the driver needs following change
set:
a. There is "max_lun" field which Driver need to set based on
hw/fw support. Currently LSI released driver does not set
this field.
b. Default of "max_lun" should not be 0 in OS, but it is
currently set to 0 in CAM layer.
c. Export max_lun capacity to 255
12. Driver will not reset target info after port enable complete and
also do Device removal when Device remove from FW. The detail
description is as follows
a. When Driver receive WD PD add events, it will add all
information in driver local data structure.
b. Only for WD, we have below checks after port enable
completes, where driver clear off all information retrieved
at #1.
if ((sc->WD_available &&
(sc->WD_hide_expose == MPS_WD_HIDE_ALWAYS)) ||
(sc->WD_valid_config && (sc->WD_hide_expose ==
MPS_WD_HIDE_IF_VOLUME)) {
// clear off target data structure.
}
It is mainly not to attach PDs to OS.
FreeBSD does bus rescan as older Parallel scsi style. So Driver
needs to handle which Drive is visible to OS. That is a reason
we have to clear off targ information for PDs.
Again, above logic was implemented long time ago. Similar concept
we have for non-wd also. For that, LSI have introduced different
logic to hide PDs.
Eventually, because of above gap, when Phy goes offline, we
observe below failure. That is what Driver is not doing complete
removal of device with FW. (which was pointed by Scott)
Apr 5 02:39:24 Freebsd7 kernel: mpslsi0: mpssas_prepare_remove
Apr 5 02:39:24 Freebsd7 kernel: mpssas_prepare_remove 497 : invalid handle 0xe
Now Driver will not reset target info after port enable complete
and also will do Device removal when Device remove from FW.
13. Returning "CAM_SEL_TIMEOUT" instead of "CAM_TID_INVALID"
error code on request to the Target IDs that have no devices
conected at that moment. As if "CAM_TID_INVALID" error code
is returned to the CAM Layaer then it results in a huge chain
of errors in verbose kernel messages on boot and every
hot-plug event.
Submitted by: Sreekanth Reddy <Sreekanth.Reddy@lsi.com>
MFC after: 3 days
the request up the tree in order to be on the safe side. Growing windows
in this case would mean to switch resources to positive decoding and
it's unclear how to correctly handle this. At least with ALi/ULi M5249
PCI-PCI bridges, this also just doesn't work out of the box.
Reviewed by: jhb
MFC after: 3 days
queue is empty or the firmware will go nuts.
PR: kern/167806
Tested by: osa@, Brandon Gooch (earlier version),
Bojan Petrovic (earlier version)
MFC after: 3 days
the TX queue is empty, there won't be a TX done notification, effectly
resulting in an mbuf leak. The correct way to handle this is to free
up mbufs on both BA and TX done notifications up to the last sent seqno.
Tested by: osa@
MFC after: 3 days
with AMPDU aggregate delimiters.
If there's an OFDM restart during an aggregate, the hardware ACKs
the previous frame, but communicates the RXed frame to the hardware
as having had CRC delimiter error + OFDM_RESTART phy error.
The frame however didn't have a CRC error and since the hardware ACKed
the aggregate to the sender, it thinks the frame was received.
Since I have no idea how often this occurs in the real world, add a
debug statement so trigger whenever this occurs. I'd appreciate an
email if someone finds this particular situation is triggered.
Bryan Cantrill implemented the equivalent of semi-log graph
paper for Dtrace so llquantize will use one logarithmic and
one linear scale.
Special thanks to Mark Peek for providing fix to an
assertion and to Fabian Keill for testing the port.
Illumos Revision: 13355:15b74a2a9a9d
Reference:
https://www.illumos/issues/905
Obtained from: Illumos
Tested by: Fabian Keill, mp
MFC after: 4 days
The Linux ath9k btcoex code is based off of this code.
Note this doesn't actually implement functional btcoex; there's some
driver glue and a whole lot of verification that is required.
On the other hand, I do have the AR9285+BT and AR9287+BT NICs which
this code supports..
Obtained from: Qualcomm Atheros, Linux ath9k
to attach to target capable HBAs that implement the old immediate
notify (XPT_IMMED_NOTIFY) and notify acknowledge (XPT_NOTIFY_ACK)
CCBs. The new API has been in place since SVN change 196008 in
2009.
The solution is two-fold: fix CTL to handle the responses from the
HBAs, and convert the HBA drivers in question to use the new API.
These drivers have not been tested with CTL, so how well they will
interoperate with CTL is unknown.
scsi_target.c: Update the userland target example code to use the
new immediate notify API.
scsi_ctl.c: Detect when an immediate notify CCB is returned
with CAM_REQ_INVALID or CAM_PROVIDE_FAIL status,
and just free it.
Fix a duplicate assignment.
aic79xx.c,
aic79xx_osm.c: Update the aic79xx driver to use the new API.
Target mode is not enabled on for this driver, so
the changes will have no practical effect.
aic7xxx.c,
aic7xxx_osm.c: Update the aic7xxx driver to use the new API.
sbp_targ.c: Update the firewire target code to work with the
new API.
mpt_cam.c: Update the mpt(4) driver to work with the new API.
Target mode is only enabled for Fibre Channel
mpt(4) devices.
MFC after: 3 days
exported via PCI passthrough.
- Do not check for a specific physical function (PF) before claiming a device.
Different PFs have different device-ids so this check is redundant anyway.
- Obtain the PF# from the WHOAMI register instead of pci_get_function().
- Setup the memory windows using the real BAR0 address, not what the VM says it
is.
Obtained from: Chelsio Communications
Possibly do some entra work in case we would not get into the
ifa0 != NULL paths later as we already do for the mltaddr before.
XXX We should possibly error in case in6_setscope fails.
Reference: http://lists.freebsd.org/pipermail/freebsd-net/2011-September/029829.html
Submitted by: bz
MFC after: 1 week
* qos[1] subfield is never assigned a value before this statement.
qos[1] can potentially be OR:ed with garbage. Make it an assignment instead;
* Remove brackets around if statement;
Approved by: adrian
pmap_remove(). The execution of these functions is no longer serialized
by the pvh global lock.
Make some stylistic changes to the affected code for the sake of
consistency with related code elsewhere in the pmap.
not by some hint setting. Do more preparations for FC-Tape.
Clean up resource counting for 24XX or later chipsets so
we find out after EXEC_FIRMWARE what is actually supported.
Set target mode exchange count based upon whether or not
we are supporting simultaneous target/initiator mode. Clean
up some old (pre-24XX) xfwoption and zfwoption issues.
Sponsored by: Spectralogic
MFC after: 3 days
the assumption that ath_softc doesn't change size based on build time
configuration.
I picked up on this because suddenly radar stuff didn't work; and
although the ath_dfs code was setting sc_dodfs=1, the main ath driver
saw sc_dodfs=0.
So for now, include opt_ath.h in driver source files. This seems like
the sane thing to do anyway.
I'll have to do a pass over the code at some later stage and turn
the radiotap TX/RX structs into malloc'ed memory, rather than in-line
inside of ath_softc. I'd rather like to keep ath_softc the same
layout regardless of configuration parameters.
Pointy hat to: adrian
a buffer pointer.
For large radar pulses, the AR9130 and later will return a series of
FFT results for software processing. These can overflow a single 2KB
buffer on longer pulses. This would result in undefined buffer behaviour.
This includes a few new fields in each RXed frame:
* per chain RX RSSI (ctl and ext);
* current RX chainmask;
* EVM information;
* PHY error code;
* basic RX status bits (CRC error, PHY error, etc).
This is primarily to allow me to do some userland PHY error processing
for radar and spectral scan data. However since EVM and per-chain RSSI
is provided, others may find it useful for a variety of tasks.
The default is to not compile in the radiotap vendor extensions, primarily
because tcpdump doesn't seem to handle the particular vendor extension
layout I'm using, and I'd rather not break existing code out there that
may be (badly) parsing the radiotap data.
Instead, add the option 'ATH_ENABLE_RADIOTAP_VENDOR_EXT' to your kernel
configuration file to enable these options.
and the CRC error bits set. The radar payload is correct.
When this happens, the stack doesn't see them PHY error frames and
isn't interpreted as a PHY error. So, no radar detection and no radiotap
PHY error handling.
Now, this may introduce some weird issues if the MAC sends up some other
combination of CRC error + PHY error frames; this commit would break that
and mark them as PHY errors instead of CRC errors.
I may tinker with this a little more to pass radar/early radar/spectral
frames up as PHY errors if the CRC bit is set, to restore the previous
behaviour (where if CRC is set on a PHY error frame, it's marked as a CRC
error rather than PHY error.)
Tested on: AR5416, over the air, to a USRP N200 which is generating a
large number of a variety of radar pulses.
TODO: Test on AR9130, AR9160, AR9280 (and maybe radar pulses on
2GHz on AR9285/AR9287.)
PR: kern/169362
a da(4) instance going away while GEOM is still probing it.
In this case, the GEOM disk class instance has been created by
disk_create(), and the taste of the disk is queued in the GEOM
event queue.
While that event is queued, the da(4) instance goes away. When the
open call comes into the da(4) driver, it dereferences the freed
(but non-NULL) peripheral pointer provided by GEOM, which results
in a panic.
The solution is to add a callback to the GEOM disk code that is
called when all of its resources are cleaned up. This is
implemented inside GEOM by adding an optional callback that is
called when all consumers have detached from a provider, and the
provider is about to be deleted.
scsi_cd.c,
scsi_da.c: In the register routine for the cd(4) and da(4)
routines, acquire a reference to the CAM peripheral
instance just before we call disk_create().
Use the new GEOM disk d_gone() callback to register
a callback (dadiskgonecb()/cddiskgonecb()) that
decrements the peripheral reference count once GEOM
has finished cleaning up its resources.
In the cd(4) driver, clean up open and close
behavior slightly. GEOM makes sure we only get one
open() and one close call, so there is no need to
set an open flag and decrement the reference count
if we are not the first open.
In the cd(4) driver, use cam_periph_release_locked()
in a couple of error scenarios to avoid extra mutex
calls.
geom.h: Add a new, optional, providergone callback that
is called when a provider is about to be deleted.
geom_disk.h: Add a new d_gone() callback to the GEOM disk
interface.
Bump the DISK_VERSION to version 2. This probably
should have been done after a couple of previous
changes, especially the addition of the d_getattr()
callback.
geom_disk.c: Add a providergone callback for the disk class,
g_disk_providergone(), that calls the user's
d_gone() callback if it exists.
Bump the DISK_VERSION to 2.
geom_subr.c: In g_destroy_provider(), call the providergone
callback if it has been provided.
In g_new_geomf(), propagate the class's
providergone callback to the new geom instance.
blkfront.c: Callers of disk_create() are supposed to pass in
DISK_VERSION, not an explicit disk API version
number. Update the blkfront driver to do that.
disk.9: Update the disk(9) man page to include information
on the new d_gone() callback, as well as the
previously added d_getattr() callback, d_descr
field, and HBA PCI ID fields.
MFC after: 5 days
This is required for ARM EABI. Section 7.1.1 of the Procedure Call for the
ARM Architecture (AAPCS) defines wchar_t as either an unsigned int or an
unsigned short with the former preferred.
Because of this requirement we need to move the definition of __wchar_t to
a machine dependent header. It also cleans up the macros defining the limits
of wchar_t by defining __WCHAR_MIN and __WCHAR_MAX in the same machine
dependent header then using them to define WCHAR_MIN and WCHAR_MAX
respectively.
Discussed with: bde
to add PV list locking to pmap_pv_demote_pde(), it is necessary to change
the way that pmap_pv_demote_pde() allocates PV entries. Specifically,
once pmap_pv_demote_pde() begins modifying the PV lists, it can't allocate
any new PV chunks, because that could require the PV list lock to be
dropped. So, all necessary PV chunks must be allocated in advance. To my
surprise, this new approach is a few percent faster than the old one.
the scheduled task from tc_windup(). Do it directly from tc_windup in
interrupt context [1].
Establish the permanent mapping of the shared page into the kernel
address space, avoiding the potential need to sleep waiting for
allocation of sf buffer during vdso_timehands update. As a
consequence, shared_page_write_start() and shared_page_write_end()
functions are not needed anymore.
Guess and memorize the pointers to native host and compat32 sysentvec
during initialization, to avoid the need to get shared_page_alloc_sx
lock during the update.
In tc_fill_vdso_timehands(), do not loop waiting for timehands
generation to stabilize, since vdso_timehands is written in the same
interrupt context which wrote timehands.
Requested by: mav [1]
MFC after: 29 days
and CAM_LUN_INVALID for case of missing devices. In removes tons of error
messages from CAM during bus scans.
Reported and tested by: Mike Tancsa <mike@sentex.net>
MFC after: 3 days
