not very usefully, in all other displays). This was the original point
of the PR.
Move the load average up by 2 so that it starts in row 0 for all windows
(2 lines above it were wasted for all other windows except vmstat).
Move everything below it up by 2 or 3 (3 for icmp and icmp6 which had
an extra blank line due from not compensating for the foot-shooting in
note (3); only ip and ip6 compensated). Reduce the magic numbers related
to this.
Notes by the submitter:
%%%
1. All the subwin() calls are identical using #define MAINWIN_ROW 3
(systat.h).
2. The load average is at the top of the window.
3. Each display starts on the fourth line. I made changes to those
displays that shifted the start line (i.e., icmp). This entailed a
lot of changes within the comments at the top of those displays.
4. For ip6, I shifted the "Input next-header histogram" column down one
row to separate it from "IPv6 Output". I raised "bad scope packets"
and "address selection failed" up one row to stay with "IPv6 Input"
(valid?). They were down one row to probably line up at the bottom,
but I think they should stick with their fellow items in a column.
5. I condensed ifstat a bit. It had a lot of empty rows.
%%%
Submitted by: Se=E1n Farley <sean-freebsd at farley dot org>
PR: bin/81874
where MB/s and tps statistics would always be zero, presumably because
they were being averaged out over the time between now and when the
system booted instead of a few seconds.
PR: 58683
Kernel:
Change statistics to use the *uptime() timescale (ie: relative to
boottime) rather than the UTC aligned timescale. This makes the
device statistics code oblivious to clock steps.
Change timestamps to bintime format, they are cheaper.
Remove the "busy_count", and replace it with two counter fields:
"start_count" and "end_count", which are updated in the down and
up paths respectively. This removes the locking constraint on
devstat.
Add a timestamp argument to devstat_start_transaction(), this will
normally be a timestamp set by the *_bio() function in bp->bio_t0.
Use this field to calculate duration of I/O operations.
Add two timestamp arguments to devstat_end_transaction(), one is
the current time, a NULL pointer means "take timestamp yourself",
the other is the timestamp of when this transaction started (see
above).
Change calculation of busy_time to operate on "the salami principle":
Only when we are idle, which we can determine by the start+end
counts being identical, do we update the "busy_from" field in the
down path. In the up path we accumulate the timeslice in busy_time
and update busy_from.
Change the byte_* and num_* fields into two arrays: bytes[] and
operations[].
Userland:
Change the misleading "busy_time" name to be called "snap_time" and
make the time long double since that is what most users need anyway,
fill it using clock_gettime(CLOCK_MONOTONIC) to put it on the same
timescale as the kernel fields.
Change devstat_compute_etime() to operate on struct bintime.
Remove the version 2 legacy interface: the change to bintime makes
compatibility far too expensive.
Fix a bug in systat's "vm" page where boot relative busy times would
be bogus.
Bump __FreeBSD_version to 500107
Review & Collaboration by: ken
and compiler warnings.
The data for network statistics are still obtained via the kvm interface
if systat was started with the needed privileges, otherwise sysctls are
used. The reason for this is that with really many open sockets, the
sysctl method is probably slower, but it systat -netstat is probably not
really usable in either mode under these conditions.
Approved by: rwatson
o Add more checks for buffer overflows
o Use snprintf rather than strcat/cpy and have better checks for max
length exceeded.
Most of these changes are not exploitable buffer overruns, but it never
hurts to be safe.
Inspired by and obtained from: OpenBSD
Use the correct value of hz (stathz if it is nonzero) for
interpretion of dk_time[] and cp_time[] in iostat.c. Avoid
multiple conversions of this value in iostat.c and vmstat.c
iostat.c:
Implement the display of cp_time[CP_INTR]. Fix the display
of cp_time[CP_IDLE] (the display was always null because
cp_time[CP_INTR] == 0 was displayed instead).
systat.1:
Document the display of cp_time[CP_INTR].
vmstat.c:
Implement the display of cp_time[CP_INTR].
