My 3C509B-COMBO works fine with the following patch. Switching between
UTP and BNC is quite easy. (Just type 'ifconfig ep0 link1 -link2' or 'ifconifg
ep0 link2 -link1'.)
[ I tested this with the additional PC-CARD patches and it works on both
connectors on my 3C589B and 3C589C ]
Reviewed by: nate
Submitted by: Naoki Hamada <nao@sbl.cl.nec.co.jp>
All new code is "#ifdef PC98"ed so this should make no difference to
PC/AT (and its clones) users.
Ok'd by: core
Submitted by: FreeBSD(98) development team
mode when this occurs and allow the target to complete the transaction.
Force a retry on overruns since they are usually caused by termination or
cable problems.
on the baud rate, dont get upset if it's been hung up by setting B0.
Instead, sleep for a short time, as the host controller takes a while
to go through the state changes.
seeing SPIORDY and checking for PHASEMIS. My last change turned out to
be less cosmetic then I thought.
Pointed out by: Satoshi Asami <asami@cs.berkeley.edu>,
Faried Nawaz <fn@pain.csrv.uidaho.edu
Cosmetic change to p_mesgout code so that it "looks" the same as what
is done in the inb* routines.
NetBSD/OpenBSD support Submitted by:Noriyuki Soda <soda@sra.co.jp>,
Pete Bentley <pete@demon.net>,
Charles M. Hannum <mycroft@mit.edu>,
Theo de Raadt <deraadt@theos.com>
phasemiss to sneak by without detection. This should fix the
Wide/Narrow boot problems that have been reported since this bug
caused the driver ignore a narrow target rejecting wide negotiation.
I spent the better part of a day trying to figure out why my
experiment didn't work the way I expected, only to find out that
the router was dropping huge numbers of packets because of PCI bus
priblems. This does not fix the bug that errors are counted as
input packets because my patch doesn't apply cleanly.
is enabled by having an "device ed0 at isa? [...]" config line.
The first PCI card will get a unit number one higher than the highest
defined for any ISA card of the ED type, e.g. if ed0 and ed1 are
configured, then the PCI cards will be ed2, ed3, ...
BEWARE: If you have configured your kernel as ed0 with the port address
as assigned by the PCI BIOS, then your card will be found by both the
PCI and ISA probes, and bad things may happen. Make sure to restore
the original port address form the GENERIC kernel for the ed0 device!
Reviewed by: davidg
1) A spelling error pointed out by Paco Hope.
2) A bug in the range checking routing pointed out by Jim Bray.
3) Enables the setting of frames per second.
Submitted-By: Jim Lowe <james@miller.cs.uwm.edu>
use sd87a or sd237e even if they start at the beginning of the slice.
You can also use sd85c if you prefer, although you need to change the
type field in the disklabel to "4.2BSD".
unreasonable time. I've got a PCI mainboard that simply doesn't grok
it, so continuing with a warning (and a keyboard that's working
nevertheless :) seems to be better than spin-looping forever.
Change #ifdef linux to #ifdef __linux__
aic7xxx_reg.h:
Remove unneeded BOFF_60BCLOCKS
define CHIPRSTACK to be the same as CHIPRST
define RESET_SCSI and CHANNEL_B_PRIMARY bits
All of these aer used during the setup of adapters.
it empties all of the 256 byte incoming fifo, as it can spend more time
processing one port than intended, especially if data is streaming in
at 115.2K. The port fifo will be emptied and dumped into the tty system
and left until next time. I've been running this for quite some time on
one of my systems here.
Also, if the tty layer is blocked or full it lets the hardware assert the
flow control rather than loosing the data.
should be <= than subordinate, not the other way around.
They are both true if the bridge is not cascaded (i.e., twin-channel
scsi/e-net adapters won't be affected by this bug), which is probably why
it was unnoticed until today.
