systems without either a CSM or real graphics drivers, such as my Lenovo
Haswell laptop.
This provides working X with the small complication of a console cursor
permanently overlaid on the upper-left corner of the screen that will be
dealt with later.
Also remove some redundant screen clearing.
rather than only drivers attached later on. This involves a small amount of
code duplication with dev/fb/fbd.c, which will fixed later on.
Also improve performance of vt_blank() by making it not read from the
framebuffer unnecessarily.
USB 2.0 port mask in addition to the USB 3.0 port mask. The hardware
does not always accept when writing -1U to the port switching
registers.
MFC after: 3 days
Tested by: Huang Wen Hui <huanghwh@gmail.com>
not done after the call to m_defrag(). This fixes a problem
where m_pullup() would prepend an mbuf to the list created
by m_defrag() making the chain greater than 32 again.
Tested by: rcarter@pinyon.org
Reviewed by: yongari, jfv
MFC after: 2 weeks
firmware allows up to 48B to be read this way but the driver limits
itself to 8B at a time to remain compatible with old cxgbetool
binaries.
MFC after: 1 week
that it can connect to switches at speeds other than 1gb.
This requires changing the reference clock speed. Since we still don't
have a general clock API that lets a SoC-independant driver manipulate its
own clocks, this change includes a weak reference to a routine named
cgem_set_ref_clk(). The default implementation is a no-op; SoC-specific
code can provide an implementation that actually changes the speed.
Submitted by: Thomas Skibo <ThomasSkibo@sbcglobal.net>
to uncacheable. This leads to execrable console performance. Once PMAP is
up, remap the framebuffer as write-combining. This reduces boot time on my
laptop by 60% when booting with EFI.
MFC after: 2 weeks
- Remove 4 extra bytes from the ethernet payload.
- The maximum RX buffer was incorrectly set. Increase it to 64K for
now, until the exact limit is understood.
- Enable hardware checksumming again.
- Make hardware data structure packed.
MFC after: 3 days
The Tx interrupt is now kept disabled in the common case, only
enabled when the number of free descriptors in the queue falls
below a threshold. Transmitted frames are cleared from the VQ
before subsequent transmit, or in the watchdog timer.
This was a very big performance improvement for an experimental
Netmap bhyve backend.
MFC after: 1 month
- add missing rcvif in mbuf
- add missing ipacket stat
- remove uncessary mbuf copy on output path
- fix deadlock of the TX engine in case of error
Obtained from: NETASQ
MFC after: 2 weeks
This includes:
o All directories named *ia64*
o All files named *ia64*
o All ia64-specific code guarded by __ia64__
o All ia64-specific makefile logic
o Mention of ia64 in comments and documentation
This excludes:
o Everything under contrib/
o Everything under crypto/
o sys/xen/interface
o sys/sys/elf_common.h
Discussed at: BSDcan
Previously ISID was changed every time, that made impossible correct
persistent reservation, because reconnected session was identified as
completely new one.
Reviewed by: trasz
MFC after: 1 week
Update some comments on code, specifying the correct vlans used on switch
setup.
Advertise the proper switch operation mode (the rtl8366rb only support
dot1q vlans).
This fixes the breakage that i introduced on r249752 and make the rtl8366rb
switch works again with etherswitchcfg(8).
Tested on TP-Link 1043ND.
Tested by: me, Harm Weites (harm at weites.com)
- Don't discard frames if the dropped or error flag is set.
- Don't remove the last 4-bytes of every packet.
- Add extra range check for data position offset when receiving data.
MFC after: 1 day
PR: 191432
The array index for the callchain is getting double-incremented -- both in the
loop and the storing. It should only be incremented in one location.
Also, constrain the stack pointer range check.
MFC after: 2 weeks
1. oce_multiq_start(): make sure the buffer is consumed even on ENXIO
2. oce_multiq_transmit(): there is an extra call to drbr_enqueue()
causing the mbuf to be enqueued twice when the NIC's queue is full,
and potential panics
3. oce_multiq_transmit(): same problem fixed recently in ixgbe (r267187)
and other drivers: if the mbuf is enqueued, the proper return value is 0
Submitted by: Stefano Garzarella
MFC after: 3 days
rules prevent the USB serial module to be unloaded before any client
modules. This patch ensures that the "ucom_mtx" mutex is destroyed
last when doing a system uninit in a monotolith build aswell.
MFC after: 3 days
