to kproc_xxx as they actually make whole processes.
Thos makes way for us to add REAL kthread_create() and friends
that actually make theads. it turns out that most of these
calls actually end up being moved back to the thread version
when it's added. but we need to make this cosmetic change first.
I'd LOVE to do this rename in 7.0 so that we can eventually MFC the
new kthread_xxx() calls.
now takes a device_t to be the parent of the bus that is being created.
Most SIMs have been updated with a reasonable argument, but a few exceptions
just pass NULL for now. This argument isn't used yet and the newbus
integration likely won't be ready until after 7.0-RELEASE.
and new SCBs were allocated on demand later if needed. This has two
problems. First, allocating SCBs involves allocating contiguous memory,
and if memory is exhausted then the VM will try to page out to satisfy
the request, leading to recursion and deadlock. The second problem is
that it can cause lock order reversals due to parts of the VM still being
under Giant.
Fix the problem be allocating the full pool at driver attach, when it is
safe to do so.
use to synchornize and protect all data objects that are used for that
SIM. Drivers that are not yet MPSAFE register Giant and operate as
usual. RIght now, no drivers are MPSAFE, though a few will be changed
in the coming week as this work settles down.
The driver API has changed, so all CAM drivers will need to be recompiled.
The userland API has not changed, so tools like camcontrol do not need to
be recompiled.
capability rather than hardcoded offsets for a particular card. While
I'm here, expand the constants some.
- Change the ahd(4) driver to use pci_find_extcap() to locate the PCI-X
capability to keep up with the first change.
Reviewed by: scottl, gibbs (earlier version)
required by arches like sparc64 (not yet implemented) and sun4v where there
are seperate IOMMU's for each PCI bus... For all other arches, it will
end up returning NULL, which makes it a no-op...
Convert a few drivers (the ones we've been working w/ on sun4v) to the
new convection... Eventually all drivers will need to replace the parent
tag of NULL, w/ bus_get_dma_tag(dev), though dev is usually different for
each driver, and will require hand inspection...
Reviewed by: scottl (earlier version)
table. Previously, the ddb code knew of each linker set of auxiliary
commands and which explicit command list they were tied to. These changes
add a simple command_table struct that contains both the static list of
commands and the pointers for any auxiliary linker set of additional
commands. This also makes it possible for other arbitrary command tables
to be defined in other parts of the kernel w/o having to edit ddb itself.
The DB_SET macro has also been trimmed down to just creating an entry in
a linker set. A new DB_FUNC macro does what the old DB_SET did which is
to not only add an entry to the linker set but also to include a function
prototype for the function being added. With these changes, it's now also
possible to create aliases for ddb functions using DB_SET() directly if
desired.
buildkernel: provide a real but dummy name to ${DEPENDFILE}
so that the relevant exists() check in bsd.prog.mk fails and
ensures that ${GENHDRS} are built before any other objects.
MFC after: 3 days
chips where setting the FAILDIS bit is not effective. While here,
try again to make it clear that reported parity errors indicate
a failure of some PCI device *other than* the aic7xxx controller.
timer reset rather than the timer of an SCB still pending on the
controller after recovery completed. This should correct timeout
loops seen in the field.
over iteration of their multicast address lists when synchronizing the
hardware address filter with the network stack-maintained list.
Problem reported by: Ed Maste (emaste at phaedrus dot sandvine dot ca>
MFC after: 1 week
aic7xxx.c:
Allow print_reg() to be called with a NULL column.
aic79xx.c:
Correct new usage of SCB_GET_TAG().
aic7xxx.c:
Fix stray ahd that snuck in here.
close holes in detecting busfrees that occur after a packetized target
transitions to a non-packetized phase. The most common case where this
occurs is when a target is externally reset so the controller believes
a packetzied negotiation agreement is still in effect. Unfortunately,
disabling this feature seems to cause problems for the 7901B. Re-enable
ehanced busfree detection for this part until I can get my hands on a
samble to figure out if the old workaround is necessary and, if so, how
to make it work correctly.
to us was to help out the Linux port, but really just invited overflow.
In fact, the request sense timer was overflowing prior to this change making
it much shorter than intended.
aic_osm_lib.h:
Be more careful about overflow in all timer/timeout primitives.
Add constants for SPI protocol delays that are needed for
target mode.
aic7xxx.c:
Correct a target mode issue that caused an occassional
spurious REQ to be seen on the bus when performing manual
message processing (e.g. transfer rate negotiation).
Enforce phase change bus settle rules with explicit
delays when performing manual message processing in
target mode. The sequencer already did this for
"fast-path", target mode message processing.
the driver to issue a bus reset more quickly than intended. We want to
*wait* if we find another SCB that could be the cause of this timeout,
not proceed to a bus reset.
Noticed by: kan
The ISA probe uses an identify routine to probe all slot locations from
1 to 14 that do not conflict with other allocated resources. This required
making aic7770.c part of the driver core when compiled as a module.
aic7xxx.c:
aic79xx.c:
aic_osm_lib.c:
Use aic_scb_timer_start() consistently to start the watchdog timer.
This removes a few places that verbatum copied the code in
aic_scb_timer_start().
During recovery processing, allow commands to still be queued to
the controller. The only requirement we have is that our recovery
command be queued first - something the code already guaranteed.
The only other change required to make this work is to prevent
timers from being started for these newly queued commands.
Approved by: re
