do exactly the same as vop_nopoll() for consistency and put a
comment in the two pointing at each other.
Retire seltrue() in favour of no_poll().
Create private default functions in kern_conf.c instead of public
ones.
Change default strategy to return the bio with ENODEV instead of
doing nothing which would lead the bio stranded.
Retire public nullopen() and nullclose() as well as the entire band
of public no{read,write,ioctl,mmap,kqfilter,strategy,poll,dump}
funtions, they are the default actions now.
Move the final two trivial functions from subr_xxx.c to kern_conf.c
and retire the now empty subr_xxx.c
This is just a cleanup here (modulo rev.1.108 of kern/tty.c), since the
input speed can be different from to output speed and extra code to
handle both speeds naturally handled all cases.
provide no methods does not make any sense, and is not used by any
driver.
It is a pretty hard to come up with even a theoretical concept of
a device driver which would always fail open and close with ENODEV.
Change the defaults to be nullopen() and nullclose() which simply
does nothing.
Remove explicit initializations to these from the drivers which
already used them.
- Removed conversion of a zero input speed to the output speed. This
has been done better in ttioctl() since rev.1.108 of kern/tty.c
almost 5 years ago. comparam() did the conversion incompletely for
the case where the output speed is also zero. It had complications
to avoid using zero speeds, but would still have used a zero input
speed for setting watermarks if kern/tty.c had passed one.
- Never permit the input speed to be different from the output speed.
There was no validity check on the input speed for the case of a zero
output speed. Then we didn't change the physical speeds, but we used
the unvalidated input speed for setting watermarks and didn't return
an error, so ttioctl() stored the unvalidated input speed in the tty
struct where it could cause problems later.
- Removed complications that were to avoid using a divisor of 0. The
divisor is now always valid if the speed is accepted.
cd_setreg() were still using !(read_eflags() & PSL_I) as the condition
for the lock hidden by COM_LOCK() (if any) being held. This worked
when spin mutexes and/or critical_enter() used hard interrupt disablement,
but it has caused recursion on the non-recursive mutex com_mtx since
all relevant interrupt disablement became soft. The recursion is
harmless unless there are other bugs, but it breaks an invariant so
it is fatal if spinlocks are witnessed.
struct msdosfsmount so that this file has the same prerequisites as
it used to. The new prerequistite was a meta-style bug. It required
many style bugs (unsorted includes ...) elsewhere.
Formatted prototypes in KNF. Resisted urge to sort all the prototypes,
to minimise differences with NetBSD. (NetBSD has reformatted the
prototypes but has not sorted them and still uses __P(()).)
node lock while sending a management frame as this will potentially
result in a LOR with a driver lock. This doesn't happen for the
Atheros driver but does for the wi driver. Use a generation number
to help process each node once when scanning the node table and
drop the node lock if we need to timeout a node and send a frame.
AP has basic rates that we do not support then ignore them instead
of marking the rate set in error.
This fixes an 11b station associating with an 11g/b AP.
are allowed by Windows (ref: MS KB article 120138).
XXX From my reading of the CIFS specification, it's not clear that
clients need to validate filenames at all.
PR: 57123
Submitted by: Paul Coucher
MFC after: 1 month
in the loopback test in the probe. The delay was too short for consoles
at speeds lower than about 3200 bps. This shouldn't have caused many
problems, since such low speeds are rare and the probe is forced to
succeed for consoles.
consdev structure.
If the consdev name is not set and we have a cn_dev, set the name
from there. Try to issue a printf about this, even though it may
not have a place to go.
Modify the sysctl related code to pick up the name from the consdev
instead.
Most of the actual use of the cn_dev field is merely to get the name,
and most of the actual initializations are bogusly using makedev()
because the probe/attach has not been completed.
Instead we will migrate console drivers to fill in the name and if
the driver needs it: the unit number, thereby avoiding the bogus
calls to makedev().
and the Z8530 drivers used the I/O address as a quick and dirty way to
determine which channel they operated on, but formalizing this by
introducing iobase is not a solution. How for example would a driver
know which channel it controls for a multi-channel UART that only has a
single I/O range?
Instead, add an explicit field, called chan, to struct uart_bas that
holds the channel within a device, or 0 otherwise. The chan field is
initialized both by the system device probing (i.e. a system console)
or it is passed down to uart_bus_probe() by any of the bus front-ends.
As such, it impacts all platforms and bus drivers and makes it a rather
large commit.
Remove the use of iobase in uart_cpu_eqres() for pc98. It is expected
that platforms have the capability to compare tag and handle pairs for
equality; as to determine whether two pairs access the same device or
not. The use of iobase for pc98 makes it impossible to formalize this
and turn it into a real newbus function later. This commit reverts
uart_cpu_eqres() for pc98 to an unimplemented function. It has to be
reimplemented using only the tag and handle fields in struct uart_bas.
Rewrite the SAB82532 and Z8530 drivers to use the chan field in struct
uart_bas. Remove the IS_CHANNEL_A and IS_CHANNEL_B macros. We don't
need to abstract anything anymore.
Discussed with: nyan
Tested on: i386, ia64, sparc64
aic7xxx_pci.c:
When performing our register test, be careful
to avoid resetting the chip when pausing the
controller. The test reads the HCNTRL register
and then writes it back with the PAUSE bit
explicitly set. If the last write to the controller
before our probe is to reset it, the CHIPRST
bit will still be set, so we must mask it off
before the PAUSE operation. On some chip versions,
we cannot access registers for a few 100us after
a reset, so this inadvertant reset was causing PCI
errors to occur on the read to check for paused
status.
Submitted by: gibbs
