If these drivers are setting M_VLANTAG because they are stripping the
layer 2 802.1Q headers, then they need to be re-inserting them so any
bpf(4) peers can properly decode them.
It should be noted that this is compiled tested only.
MFC after: 3 weeks
sparc64 GENERIC and the sound device drivers known working on sparc64
to use bus_get_dma_tag() to obtain the parent DMA tag so we can get rid
of the sparc64_root_dma_tag kludge eventually. Except for ath(4), sk(4),
stge(4) and ti(4) these changes are runtime tested (unless I booted up
the wrong kernels again...).
m_pkthdr.ether_vlan. The presence of the M_VLANTAG flag on the mbuf
signifies the presence and validity of its content.
Drivers that support hardware VLAN tag stripping fill in the received
VLAN tag (containing both vlan and priority information) into the
ether_vtag mbuf packet header field:
m->m_pkthdr.ether_vtag = vlan_id; /* ntohs()? */
m->m_flags |= M_VLANTAG;
to mark the packet m with the specified VLAN tag.
On output the driver should check the mbuf for the M_VLANTAG flag to
see if a VLAN tag is present and valid:
if (m->m_flags & M_VLANTAG) {
... = m->m_pkthdr.ether_vtag; /* htons()? */
... pass tag to hardware ...
}
VLAN tags are stored in host byte order. Byte swapping may be necessary.
(Note: This driver conversion was mechanic and did not add or remove any
byte swapping in the drivers.)
Remove zone_mtag_vlan UMA zone and MTAG_VLAN definition. No more tag
memory allocation have to be done.
Reviewed by: thompsa, yar
Sponsored by: TCP/IP Optimization Fundraise 2005
if_watchdog, etc., or in functions used only in these methods.
In all other functions in the driver use device_printf().
- Use __func__ instead of typing function name.
Submitted by: Alex Lyashkov <umka sevcity.net>
Use proper pointer dereference to inform modified mbuf chains to
caller.
While I'm here perform checksum offload setup after loading DMA
maps.
In collaboration with: glebius
requiried to keep consistent softc state before/after callback function
invocation and supposed to be sligntly faster than previous one as it
wouldn't incur callback overhead. With this change callback function
was gone.
- Decrease TI_MAXTXSEGS to 32 from 128. It seems that most mbuf chain
length is less than 32 and it would be re-packed with m_defrag(9) if
its chain length is larger than TI_MAXTXSEGS. This would protect ti(4)
against possible kernel stack overflow when txsegs[] is put on stack.
Alternatively, we can embed the txsegs[] into softc. However, that
would waste memory and make Tx/Rx speration hard when we want to
sperate Tx/Rx handlers to optimize locking.
- Fix dma map tracking used in Tx path. Previously it used the dma map
of the last mbuf chain in ti_txeof() which was incorrect as ti(4)
used dma map of the first mbuf chain when it loads a mbuf chain with
bus_dmamap_load_mbuf(9). Correct the bug by introducing queues that
keep track of active/inactive dma maps/mbuf chain.
- Use ti_txcnt to check whether driver need to set watchdog timer instead
of blidnly clearing the timer in ti_txeof().
- Remove the 3rd arg. of ti_encap(). Since ti(4) now caches the last
descriptor index(ti_tx_saved_prodidx) used in Tx there is no need to
pass it as a fuction arg.
- Change data type of producer/consumer index to int from u_int16_t in
order to remove implicit type conversions in Tx/Rx handlers.
- Check interface queue before getting a mbuf chain to reduce locking
overhead.
- Check number of available Tx descriptores to be 16 or higher in
ti_start(). This wouldn't protect Tx descriptor shortage but it would
reduce number of bus_dmamap_unload(9) calls in ti_encap() when we are
about to running out of Tx descriptors.
- Command NIC to send packets ony when the driver really has packets
enqueued. Previously it always set TI_MB_SENDPROD_IDX which would
command NIC to DMA Tx descriptors into NIC local memory regardless
of Tx descriptor changes.
Reviewed by: scottl
. remove unnecessay header files after Scott's bus_dma(9) commit.
. remove global variable tis which was introduced at the time of
zero_copy(9) changes. The variable tis was not used at all. The
same applyes to ti_links in softc so axe it.
. deregister variables.
. axe ti_vhandle and switch to use explicit register access for
accessing NIC local memory. Creates three variants of ti_mem to
read/write NIC local memory(ti_mem_read, ti_mem_write) and clearing
NIC local memory(ti_mem_zero). This greatly enhances code
readability and have ti(4) drop using shared memory scheme for
Tigon 1. As Tigon 1 switched to use explicit register access for Tx,
axe ti_tx_ring_nic/ti_cmd_ring in softc.(Tigon 2 used to host ring
scheme which means there is no need to access NIC local memory via
register access for Tx and NIC would DMA the modified Tx rings into
its local memory.) [1]
. introduce new macro TI_EVENT_*/TI_CMD_* to handle NIC envent/command.
Instead of using bit fields assginment for accessing the event, use
shift operations to set/get it. [1]
. add additional check for valid DMA tags in ti_free_dmamaps().
. add missing bus_dmamap_sync/bus_dmamap_unload in ti_free_*_ring_*.
. fix locking nits(MTX_RECURSE mutex) and make ti(4) MPSAFE.
. change data type of ti_rdata_phys to bus_addr_t and don't blindly
cast to uint32_t.
. rearrange detach path and make ti(4) survive during device detach.
. for Tigon 1, use explicit register access for checking Tx descriptors
in ti_encap()/ti_txeof(). [1]
. properly call bus_dmamap_sync(9) for updating statistics.
. remove extra semicolon in ti_encap()
. rewrite loading MAC address to work on strict-alignment architectures.
. move TI_RD_OFF macro to if_tireg.h
. axe ETHER_ALIGN as it's already defined in <net/ethernet.h>.
. make macros immuine from expansion by adding parenthesis and do-while.
. remove alpha specific hack as vtophys(9) is no longer used in ti(4)
after Scott's bus_dma(9) fix.
Reviewed by: scottl
Obtained from: OpenBSD [1]
case if memory allocation failed.
- Remove fourth argument from VLAN_INPUT_TAG(), that was used
incorrectly in almost all drivers. Indicate failure with
mbuf value of NULL.
In collaboration with: yongari, ru, sam
to use busdma. Unlike most of the other drivers, but similar to the
if_em driver, pre-allocate the dmamaps at init time instead of allocating
them on the fly when descriptors need to be filled. This isn't ideal right
now because a map is allocated for every descriptor slot in the tx, rx, mini,
and jumbo rings (which is a lot!) in order to simplify the bookkeeping, even
though the driver might support filling only a subset of those slots.
Luckily, maps are typically NULL on i386 and amd64, so the cost isn't
very high. It could be an issue with sparc64, but the driver isn't endian
clean either, and that is a much bigger problem to solve first.
Note that jumbo frame support is under-tested, and I'm not even sure if
it till really works correctly given the evil VM magic that is does.
The changes here attempt to preserve the existing semanitcs.
Thanks to Martin Nillson for contributing the Netgear card for this work.
MFC-After: 3 weeks
rather than in ifindex_table[]; all (except one) accesses are
through ifp anyway. IF_LLADDR() works faster, and all (except
one) ifaddr_byindex() users were converted to use ifp->if_addr.
- Stop storing a (pointer to) Ethernet address in "struct arpcom",
and drop the IFP2ENADDR() macro; all users have been converted
to use IF_LLADDR() instead.
IFF_DRV_RUNNING, as well as the move from ifnet.if_flags to
ifnet.if_drv_flags. Device drivers are now responsible for
synchronizing access to these flags, as they are in if_drv_flags. This
helps prevent races between the network stack and device driver in
maintaining the interface flags field.
Many __FreeBSD__ and __FreeBSD_version checks maintained and continued;
some less so.
Reviewed by: pjd, bz
MFC after: 7 days
over iteration of their multicast address lists when synchronizing the
hardware address filter with the network stack-maintained list.
Problem reported by: Ed Maste (emaste at phaedrus dot sandvine dot ca>
MFC after: 1 week
struct ifnet or the layer 2 common structure it was embedded in have
been replaced with a struct ifnet pointer to be filled by a call to the
new function, if_alloc(). The layer 2 common structure is also allocated
via if_alloc() based on the interface type. It is hung off the new
struct ifnet member, if_l2com.
This change removes the size of these structures from the kernel ABI and
will allow us to better manage them as interfaces come and go.
Other changes of note:
- Struct arpcom is no longer referenced in normal interface code.
Instead the Ethernet address is accessed via the IFP2ENADDR() macro.
To enforce this ac_enaddr has been renamed to _ac_enaddr.
- The second argument to ether_ifattach is now always the mac address
from driver private storage rather than sometimes being ac_enaddr.
Reviewed by: sobomax, sam
zero-copy receive of jumbo frames. This eliminates the need for the
jumbo frame allocator implemented in kern/uipc_jumbo.c and sys/jumbo.h.
Remove it.
Note: Zero-copy receive of jumbo frames did not work without these changes;
I believe there was insufficient locking on the jumbo vm object.
Tested by: ken@
Discussed with: gallatin@
Introduce d_version field in struct cdevsw, this must always be
initialized to D_VERSION.
Flip sense of D_NOGIANT flag to D_NEEDGIANT, this involves removing
four D_NOGIANT flags and adding 145 D_NEEDGIANT flags.
Free approx 86 major numbers with a mostly automatically generated patch.
A number of strategic drivers have been left behind by caution, and a few
because they still (ab)use their major number.
the packets are immediately returned for sending (e.g. when bridging
or packet forwarding). There are more efficient ways to do this
but for now use the least intrusive approach.
Reviewed by: imp, rwatson
if_xname, if_dname, and if_dunit. if_xname is the name of the interface
and if_dname/unit are the driver name and instance.
This change paves the way for interface renaming and enhanced pseudo
device creation and configuration symantics.
Approved By: re (in principle)
Reviewed By: njl, imp
Tested On: i386, amd64, sparc64
Obtained From: NetBSD (if_xname)
