and used by uart(4) for the channel conflicted with the port offset for
the Z8530. The Z8530 has the channels reversed (i.e. channel B is at
offset 0 and channel A is at offset 4). Assign the port offsets in the
right order so that uart(4) will properly attach to the channels.
Submitted by: Marius Strobl <marius@alchemy.franken.de>
It was fixed by moving problemetic checks, as well as checks that
doesn't need locking before locks are acquired.
Submitted by: Ryan Sommers <ryans@gamersimpact.com>
In co-operation with: cperciva, maxim, mlaier, sam
Tested by: submitter (previous patch), me (current patch)
Reviewed by: cperciva, mlaier (previous patch), sam (current patch)
Approved by: sam
Dedicated to: enough!
SCHED_INTERACT_MAX was used where SCHED_SLP_RUN_MAX was needed. This was
causing the interactivity scaler to lose history at a more dramatic rate
than intended.
scenario into #ifdef DEBUG. This makes my cluster with Belkin
KVM switch completely usable, even if the KVM switch and mouse
get a bit confused sometimes.
Without this, when the mouse gets confused, all sorts of crud
gets spammed all over the screen. With this, the mouse may appear
dead for a second or three, but it recovers silently.
Now, if we have for example: ad0s1 ad0s1c ad2s1 ad2s1c and we will try
to do: gconcat label foo /dev/ad0s1 /dev/ad2s1 we'll get a panic:
panic: spoiled but dcr = 1
for inside of geom_slice class, backtrace shows:
g_access()
g_slice_access()
g_access()
g_concat_read_metadata()
We need to get a proper fix for this race before geom(8) will be committed.
phandle_t. Since both are typedefed to unsigned int, this is more
or less cosmetic.
- Fix the code that determines whether a creator instance was used
for firmware output (and should not be blanked on initialization).
Since r1.2 of dev/fb/creator.c, this consisted comparing a handle of
an instance of a package with a handle of the package itself.
Use the test from r1.1, which utilizes OF_instance_to_package().
Submitted by: Marius Strobl <marius@alchemy.franken.de>
+ struct ifnet: remove unused fields, move ipv6-related field close
to each other, add a pointer to l3<->l2 translation tables (arp,nd6,
etc.) for future use.
+ struct route: remove an unused field, move close to each
other some fields that might likely go away in the future
"...If "keyboard" is the selected input-device and "screen" the
output-device (both via /options) but the keyboard is unplugged,
OF automatically switches to ttya for the console, it even prints
a line telling so on "screen". Solaris respects this behaviour and
uses ttya as the console in this case and people probably expect
FreeBSD to do the same (it's also very handy to temporarily switch
consoles)..."
"...I changed the comparison of the console device with "ttya" ||
"ttyb" to "tty" because on AXe boards all 4 onboard UARTs end in
SUB-D connectors (ttya and ttyb being 16550 and ttyc and ttyd a
SAB82532) and there's no Sun keyboard connector (but PS/2). If one
plugs a serial card in a box there also can be more than just ttya
and ttyb available for a console..."
Submitted by: Marius Strobl <marius@alchemy.franken.de>
Has no doubt that the change is correct: marcel
"... uart_cpu_sparc64.c currently only looks at /options if ttyX is
the selected console. However, there's one case where it should
additionally look at /chosen. If "keyboard" is the selected input-
device and "screen" the output-device (both via /options) but the
keyboard is unplugged, OF automatically switches to ttya for the
console. It even prints a line telling so on "screen". Solaris
respects this behaviour and uses ttya as the console in this case
and people probably expect FreeBSD to do the same (it's also very
handy to temporarily switch consoles)..."
Submitted by: Marius Strobl <marius@alchemy.franken.de>
Has no doubt the change is correct: marcel
