before selecting a mode. The Seeq PHY chips on the Adaptec cards that
use the AIC-6915 controller seem to need it in order to get them to
change modes correctly.
This corrects a problem that I noticed where my ANA-62022 board failed
to correctly program the full duplex bit in the macconfig1 register
when the interface was brought up. Running ifconfig sf0 would mask this
problem in some cases because polling the PHY status would cause the
miibus code to notice that full duplex was now needed and the statchg
callback would be invoked to configure the duplex setting. However it
would still get it wrong other times.
Also changed sf_miibus_statchg() to program the IPG register to match
the duplex setting in accordance with Adaptec manual's recommendations
(0x15 for full duplex, 0x11 for half duplex).
which it replaces. The new driver supports all of the chips supported
by the ones it replaces, as well as many DEC/Intel 21143 10/100 cards.
This also completes my quest to convert things to miibus and add
Alpha support.
device_add_child_ordered(). 'ivars' may now be set using the
device_set_ivars() function.
This makes it easier for us to change how arbitrary data structures are
associated with a device_t. Eventually we won't be modifying device_t
to add additional pointers for ivars, softc data etc.
Despite my best efforts I've probably forgotten something so let me know
if this breaks anything. I've been running with this change for months
and its been quite involved actually isolating all the changes from
the rest of the local changes in my tree.
Reviewed by: peter, dfr
by identifying the version in the PCI drivers.
The OHCI driver just presets this to 1.0 as it is not specified in the
PCI registers anywhere. This should be revisited once USB 2.0 is in
wide spread use.
rather than an "it's mine!" so that other newbus-aware drivers can
bid for the device too. This should allow the sym driver to out-bid
the ncr driver for devices it supports without having to modify ncr.c
at all. ncr would then function as a catch-all.
parameter a char ** instead of a const char **. This make these
kernel routines consistent with the corresponding libc userland
routines.
Which is actually 'correct' is debatable, but consistency and
following the spec was deemed more important in this case.
Reviewed by (in concept): phk, bde
pci_probe_nomatch, so it won't be in the way when loading USB as a module.
The reason for them being there in the first place is that every
motherboard comes with USB kit and this way it looks more pretty (peter).
The real solution will be to define some method of detaching a driver
after it has attached.
out of the PCI CLASS reg and store it in the softc. Use the getenv_quad
function to get a WWN override from the environment. Look for a config
value for same. Make slightly less lame the wwn seed construction.
is documented to be 0x18 in the Adaptec manual, however there appears to
be a newer board rev with code 0x19. I added a #define for this and
updated the probe code so that this board will be properly identified
in the probe messages. (Currently it's just identified generically as
an AIC-6915 chip.)
"rw" argument, rather than hijacking B_{READ|WRITE}.
Fix two bugs (physio & cam) resulting by the confusion caused by this.
Submitted by: Tor.Egge@fast.no
Reviewed by: alc, ken (partly)
- Fix a bug in rl_rxeof() handler: in the case where the packet wraps
from the end of the receive buffer back to the beginning, we need to
insure that at least sizeof(ether_header) bytes make it into the first
mbuf. If we don't, then doing eh = mtod(m, struct ether_header *)
loses. To avoid this, we use m_pullup() to suck at least MHLEN -
RL_ETHER_ALIGN bytes into the first mbuf, which should also help
small packets fit into a single mbuf.
Pointed out by: Philip A. Prindeville <philipp@zembu.com>
- Make the transmit threshold autotuning: start off with a small value
and jack it up when TX underruns are detected.
- Also improve TX error recovery: kick the chip in the head with a
reset/init sequence to make sure it recovers afer a transmit error.
have you is prototyped). Removed code versions in md struct- not used
any more. Allocate transfer dma maps and xflist stuff in mbxdmasetup based
upon isp->isp_maxcmds. Allow for multiple calls to mbxdmasetup (for
isp_reset cases).
In order to make this work, I created a pseudo-PHY driver to deal with
Macronix chips that use the built-in NWAY support and symbol mode port.
This is actually all of them, with the exception of the original MX98713
which presents its NWAY support via the MII serial interface.
The mxphy driver actually manipulates the controller registers directly
rather than using the miibus_readreg()/miibus_writereg() bus interface
since there are no MII registers to read. The mx driver itself pretends
that the NWAY interface is a PHY locayed at MII address 31 for the sole
purpose of allowing the mxphy_probe() routine to know when it needs to
attach to a host controller.
- When setting/clearing promisc mode, just update the filter, don't
reset the whole interface.
- Call xl_init() in xl_ifmedia_upd() when setting miibus media modes. This
fixes a problem with the 3c905B-COMBO where switching from 10base5/AUI
or 10base2/BNC to a 10/100 mode doesn't always work right.
- Attempt to reset the interface in xl_init() so that we know we're getting
the receive and transmit rings reset properly.
* Change the hack used on the alpha for mapping devices into DENSE or
BWX memory spaces to a simpler one. Its still a hack and should be
a seperate api to explicitly map the resource.
* Add $FreeBSD$ as necessary.
Rather than teaching pci_ioctl about hoses, we just pass down a magic number
& let the platform code figure out what the hose is based on what the bus
number is.
concept approved by dfr
