allowed either because of the transport or configuration, send a
MRU NAK only once, then allow the negotiations to proceed.
rfc1661 says that 1500 should always be allowed and rfc2516 says
that 1492 is the maximum for PPPoE. This changes ppp so that it
only weakly suggests 1492, then goes with the default (leaving
the problem in the hands of the peer WRT how they set their MTU).
MFC after: 1 week
the existence of the __gnuc_va_list type[*] because our compiler is GCC.
[*] __gnuc_va_list is defined in the GCC ginclude/stdarg.h replacement
headerwhich we don't use.
- Only release Giant in trap() if we locked it, otherwise we could release
Giant in a kernel trap if we didn't get it for a page fault and the
previous frame had grabbed the lock.
- Only get Giant for !MP safe syscalls.
index, then retrieve statistics for that index, rather than retrieving
all interfaces and then looking for a matching name. This allows the
user to refer to an interface via an alias name.
While I'm here, also perform a few assorted cleanups.
Have sys/net/route.c:rtrequest1(), which takes ``rt_addrinfo *''
as the argument. Pass rt_addrinfo all the way down to rtrequest1
and ifa->ifa_rtrequest. 3rd argument of ifa->ifa_rtrequest is now
``rt_addrinfo *'' instead of ``sockaddr *'' (almost noone is
using it anyways).
Benefit: the following command now works. Previously we needed
two route(8) invocations, "add" then "change".
# route add -inet6 default ::1 -ifp gif0
Remove unsafe typecast in rtrequest(), from ``rtentry *'' to
``sockaddr *''. It was introduced by 4.3BSD-Reno and never
corrected.
Obtained from: BSD/OS, NetBSD
MFC after: 1 month
PR: kern/28360
- Report destination address of a P2P link when servicing
routing socket messages.
- Report interface name, address, and destination address
of a P2P link when servicing NET_RT_{DUMP,FLAGS} sysctls.
Part of CSRG revision 8.6 coresponds to revision 1.12.
CSRG revision 8.7 corresponds to revision 1.15.
been misled to believe by unknown parties. It probably *should* be an option,
but the runtime value is controlled by a tunable, which Ought To Be Enough.
spin in a loop eating CPU time. This bug has existed since the
TI-RPC import. The problem is that we should only enter the select
loop if at least one TCP server was started. Fix this by having
the master nfsd become a UDP server itself if there are no TCP
servers.
Also improve/correct the code for cleaning up slave nfsd processes
and unregistering with rpcbind when the master nfsd exits.
One issue that remains open is that if a slave nfsd dies, then all
nfsds will shut down. This is because nfssvc() in the master nfsd
returns 0 when the master nfsd receives a SIGCHLD.
Submitted by: tmm
Use the normal interrupt handler (npx_intr()) instead of a special
probe-time interrupt handler, although this causes problems due to
the bus_teardown_intr() not actually even tearing down the interrupt
(these problems were avoided by doing interrupt attachment for the
special interrupt handler directly). Fixed minor bitrot in comments.
The reason for the npxprobe()/npxprobe1() split mostly went away at
about the same time it was made (in 1992 or 1993 just before the
beginning of history). 386BSD ran all probes with interrupts completely
masked, and I didn't want to disturb this when I added an irq probe
to npxprobe(). An irq (not necessarily npx) must be acked for at least
external npx's to take the cpu out of the wait state that it enters
when an npx error occurs, so the probe must be done with a suitable
irq unmasked. npxprobe() went to great lengths to unmask precisely
the npx irq.
Running probes with all interrupts masked was never really needed in
FreeBSD, since FreeBSD always masked interrupts well enough using
splhigh(), but it wasn't until rev.1.48 (1995/12/12) of autoconf.c
that all probes were run with CPU interrupts enabled. This permits
npxprobe() to probe its irq using normal interrupt resources. Note
that most drivers still can't depend on this. It depends on the
interrupt handler being fast and the irq not being shared.
