of "dumb" PCI-based serial/parallel boards get a hint how to enable
them.
I wasn't sure about the ia64, pc98, powerpc, and sparc64 archs whether
they'd support puc(4) or not.
reserved bits in the port that must be zero are 24:30, not 20:30. Bits
16:23 are used to set the bus number. This meant that when we tested for
config mechanism #1, if the previous PCI configuration transaction sent
used a bus number greater than 15, one of the bits in 20:23 would be
non-zero and we would fail to use config mechanism #1 and thus fail to see
that PCI existed on the machine at all.
Obtained from: Shanley's PCI System Architecture book
Tested by: des
Proxied through: njl
user mode. This goes with rev.1.468 of machdep.c which changed the gates
for these traps to interrupt gates. Having the interrupts disabled for
these traps from user mode is just an unwanted side effect.
This fixes at least 1 case of "panic: absolutely cannot call
smp_ipi_shootdown with interrupts already disabled". Too much code was
run with interrupts disabled, and it sometimes hit a sanity check.
Fix verified by: deischen
pmap_remove_pte(), passed NULL instead of the required page table
page to pmap_unuse_pt(). Compute the necessary page table page
in pmap_remove_pte(). Also, remove some unreachable code from
pmap_remove_pte().
intpin register is expressed in hardware where 0 means none, 1 means INTA,
2 INTB, etc. The other way is commonly used in loops where 0 means INTA,
1 means INTB, etc. The matchpin argument to pci_cfgintr_search() is
supposed to be the first form, but we passsed in a loop index of the
second. This fix adds one to the loop index to convert to the first form.
Reported by: Pavlin Radoslavov <pavlin@icir.org>
written by Stuart Walsh and Duncan Barclay (with some kibbitzing by
me). I'm checking it in on Stuart's behalf.
The BCM4401 is built into several x86 laptop and desktop systems. For the
moment, I have only enabled it in the x86 kernel config because although
it's a PCI device, I haven't heard of any standalone NICs that use it. If
somebody knows of one, we can easily add it to the other arches.
This driver uses register/structure data gleaned from the Linux
driver released by Broadcom, but does not contain any of the code
from the Linux driver itself. It uses busdma.
atomically extracts and holds the physical page that is associated with the
given pmap and virtual address. Such a function is needed to make the
memory mapping optimizations used by, for example, pipes and raw disk I/O
MP-safe.
Reviewed by: tegge
rl(4) driver and put it in a new re(4) driver. The re(4) driver shares
the if_rlreg.h file with rl(4) but is a separate module. (Ultimately
I may change this. For now, it's convenient.)
rl(4) has been modified so that it will never attach to an 8139C+
chip, leaving it to re(4) instead. Only re(4) has the PCI IDs to
match the 8169/8169S/8110S gigE chips. if_re.c contains the same
basic code that was originally bolted onto if_rl.c, with the
following updates:
- Added support for jumbo frames. Currently, there seems to be
a limit of approximately 6200 bytes for jumbo frames on transmit.
(This was determined via experimentation.) The 8169S/8110S chips
apparently are limited to 7.5K frames on transmit. This may require
some more work, though the framework to handle jumbo frames on RX
is in place: the re_rxeof() routine will gather up frames than span
multiple 2K clusters into a single mbuf list.
- Fixed bug in re_txeof(): if we reap some of the TX buffers,
but there are still some pending, re-arm the timer before exiting
re_txeof() so that another timeout interrupt will be generated, just
in case re_start() doesn't do it for us.
- Handle the 'link state changed' interrupt
- Fix a detach bug. If re(4) is loaded as a module, and you do
tcpdump -i re0, then you do 'kldunload if_re,' the system will
panic after a few seconds. This happens because ether_ifdetach()
ends up calling the BPF detach code, which notices the interface
is in promiscuous mode and tries to switch promisc mode off while
detaching the BPF listner. This ultimately results in a call
to re_ioctl() (due to SIOCSIFFLAGS), which in turn calls re_init()
to handle the IFF_PROMISC flag change. Unfortunately, calling re_init()
here turns the chip back on and restarts the 1-second timeout loop
that drives re_tick(). By the time the timeout fires, if_re.ko
has been unloaded, which results in a call to invalid code and
blows up the system.
To fix this, I cleared the IFF_UP flag before calling ether_ifdetach(),
which stops the ioctl routine from trying to reset the chip.
- Modified comments in re_rxeof() relating to the difference in
RX descriptor status bit layout between the 8139C+ and the gigE
chips. The layout is different because the frame length field
was expanded from 12 bits to 13, and they got rid of one of the
status bits to make room.
- Add diagnostic code (re_diag()) to test for the case where a user
has installed a broken 32-bit 8169 PCI NIC in a 64-bit slot. Some
NICs have the REQ64# and ACK64# lines connected even though the
board is 32-bit only (in this case, they should be pulled high).
This fools the chip into doing 64-bit DMA transfers even though
there is no 64-bit data path. To detect this, re_diag() puts the
chip into digital loopback mode and sets the receiver to promiscuous
mode, then initiates a single 64-byte packet transmission. The
frame is echoed back to the host, and if the frame contents are
intact, we know DMA is working correctly, otherwise we complain
loudly on the console and abort the device attach. (At the moment,
I don't know of any way to work around the problem other than
physically modifying the board, so until/unless I can think of a
software workaround, this will have do to.)
- Created re(4) man page
- Modified rlphy.c to allow re(4) to attach as well as rl(4).
Note that this code works for the sample 8169/Marvell 88E1000 NIC
that I have, but probably won't work for the 8169S/8110S chips.
RealTek has sent me some sample NICs, but they haven't arrived yet.
I will probably need to add an rlgphy driver to handle the on-board
PHY in the 8169S/8110S (it needs special DSP initialization).
Quick fix for calling DELAY() for ddb input in some (atkbd-based)
console drivers. ddb must not use any normal locks, but DELAY()
normally calls getit() which needs clock_lock. One problem with using
normal locks in ddb is that deadlock is possible, but deadlock on
clock_lock is unlikely becaluse clock_lock is bogusly recursive,
apparently just to hide the problem of ddb using it. The i8254 clock
hardware has mostly write-only registers so it is important for it to
use a lock that gives exclusive access. (atkbd hardware is also
unfriendly to reentrant software but that problem is more local and
already solved.) I mostly saw the symptoms of the bug caused by
unlocking in getit() running cpu_unpend(). cpu_unpend() should not
be called while in ddb and Debugger() calls for failing assertions
about this caused a breakpoint within ddb.
ddb must also not call getit() because ddb may be being used to step
through clock initialization code that has stopped or otherwise mangled
the clock. If the clock is stopped, then getit() always returns the
same value and DELAY() takes forever if it trusts getit().
The quick fix is implement DELAY(n) as (n * timer_freq / 1000000)
inb(0x84)'s if ddb is active.
machdep.c:
Don't permit recursion on clock_lock.
kdb_trap(). Stopping the other CPUs acts like locking them out, but
it wasn't done early enough or held long enough to prevent concurrent
accesses to shared data. In particular, the saved regs could be
clobbered.
sockets into machine-dependent files. The rationale for this
migration is illustrated by the modified amd64 allocator. It uses the
amd64's direct map to avoid emphemeral mappings in the kernel's
address space. On an SMP, the emphemeral mappings result in an IPI
for TLB shootdown for each transmitted page. Yuck.
Maintainers of other 64-bit platforms with direct maps should be able
to use the amd64 allocator as a reference implementation.
change also disables interrupts around non-S4 suspends whereas before we
did not do this. Our version of AcpiEnterSleepStateS4bios was almost
identical to the ACPICA version.
- Add a new PCIM_HDRTYPE constant for the field in PCIR_HDRTYPE that holds
the header type.
- Replace several magic numbers with appropriate constants for the header
type register and a couple of PCI_FUNCMAX.
- Merge to amd64 the fix to the i386 bridge code to skip devices with
unknown header types.
Requested by: imp (1, 2)
_pmap_allocpte(): Guarantee that the page table page is zero filled before
adding it to the directory. Otherwise, a 2nd, 3rd, etc. thread could
access a nearby virtual address and use garbage for the address
translation.
Discussed with: peter, tegge
prototypes of cpu_halt(), cpu_reset() and swi_vm() from md_var.h to
cpu.h. This affects db_command.c and kern_shutdown.c.
ia64: move all MD prototypes from cpu.h to md_var.h. This affects
madt.c, interrupt.c and mp_machdep.c. Remove is_physical_memory().
It's not used (vm_machdep.c).
alpha: the MD prototypes have been left in cpu.h with a comment
that they should be there. Moving them is left for later. It was
expected that the impact would be significant enough to be done in
a seperate commit.
powerpc: MD prototypes left in cpu.h. Comment added.
Suggested by: bde
Tested with: make universe (pc98 incomplete)
