OBJ_ONEMAPPING in the case where an object is extended by an
additional vm_map_entry must be allocated.
In vm_object_madvise(), remove calll to vm_page_cache() in MADV_FREE
case in order to avoid a page fault on page reuse. However, we still
mark the page as clean and destroy any swap backing store.
Submitted by: Alan Cox <alc@cs.rice.edu>
3c905B, the RX and TX reset commands also reset the cyclone chip's internal
PHY, which causes it to restart its autonegotiation session. This takes a
second or two to complete, which makes the interface seem to stop responding
for a few seconds every time you do something that reinitializes it.
Issuing the RX and TX resets on the older 3c905 boomerang adapters doesn't
cause any delay because the boomerang chip requires an external PHY.
This should fix the problem where people doing network installs via 3c905B
cards experience a delay after the interface is first initialized, among
other things.
Submitted by Roger Hardiman.
Added ioctl TVTUNER_GETCHANSET to discover which regions the bktr driver
supports. Submitted by Vsevolod Lobko <seva@alex-ua.com>
Added BT848_GPIO_SET_EN,BT848_GPIO_SET_DATA (and GETs) to allow user land
control of the GPIO pins. This allows a Radio module on the GPIO port
to be controlled. Submitted by Vsevolod Lobko <seva@alex-ua.com>
The kernel option BKTR_GPIO_ACCESS must be used to enable the GPIO ioctls.
Submitted by: Roger Hardiman and Vsevolod Lobko <seva@alex-ua.com>
when the process starts, and having it nonzero causes statically-linked
Linux binaries to fail.
PR: i386/10015
Submitted by: Marcel Moolenaar <marcel@scc.nl>
the same name. Silently return EEXIST if this happens.
vinum_scandisk: Collect drive numbers, not pointers, to avoid problems
of relocated drives.
Tripped-over-by: Bernd Walter <ticso@cicely.de>
time out on an operation. Under these circumstances, vinum(8) will
automatically start another daemon. Add a pid for the daemon, so that
an overtaken daemon will discover that it's no longer in favour, and
will crawl into a corner and die.
peripheral drivers can determine where in the devstat(9) list they are
inserted.
This requires recompilation of libdevstat, systat, vmstat, rpc.rstatd, and
any ports that depend on the devstat code, since the size of the devstat
structure has changed. The devstat version number has been incremented as
well to reflect the change.
This sorts devices in the devstat list in "more interesting" to "less
interesting" order. So, for instance, da devices are now more important
than floppy drives, and so will appear before floppy drives in the default
output from systat, iostat, vmstat, etc.
The order of devices is, for now, kept in a central table in devicestat.h.
If individual drivers were able to make a meaningful decision on what
priority they should be at attach time, we could consider splitting the
priority information out into the various drivers. For now, though, they
have no way of knowing that, so it's easier to put them in an easy to find
table.
Also, move the checkversion() call in vmstat(8) to a more logical place.
Thanks to Bruce and David O'Brien for suggestions, for reviewing this, and
for putting up with the long time it has taken me to commit it. Bruce did
object somewhat to the central priority table (he would rather the
priorities be distributed in each driver), so his objection is duly noted
here.
Reviewed by: bde, obrien
convince myself that nothing will break if we permit IP input while
interface addresses are unconfigured. (At worst, they will hit some
ULP's PCB scan and fail if nobody is listening.) So, remove the restriction
that addresses must be configured before packets can be input. Assume
that any unicast packet we receive while unconfigured is potentially ours.
because there was a concensus on current in regards to leaving bss r+w+x
instead of r+w. This is in order to maintain reasonable compatibility
with existing JIT compilers (e.g. kaffe) and possibly other programs.
define. Add a new config flag param (ISP_CFG_NONVRAM) whose intent it is
to cause NVRAM to be ignored. Add ISPASYNC_LOOP_DOWN and ISPASYNC_LOOP_UP
isp_async enums.
Amazingly enough, I did all my scsi_sa work recently without realizing
that I had a broken isp card whose (unchangeable- it's an old old old
isp1020) NVRAM has sync mode enabled, but disconnect/reconnect disabled-
the ISP_CFG_NONVRAM is definitely warranted when you want to bloody well
ignore the NVRAM and set something sensible.
Use fast memory timing NVRAM parameter. Clean up and fix establishment
of default target parameters. Don't use NVRAM if are flagged as not to
do so (I had a busted NVRAM setup which I couldn't edit that enabled SYNC
mode but disabled disconnect/reconnect and wide!!). Fix delays after
resets. BUS resets not done in isp_init anymore- relegated to OS
specific outer layers. Fix a buglet where you can get in a loop for
a NULL xs in the completion list in isp_intr. Add in some defines that
can disable fast posting. Add in code for Loop Up/Loop Down events that
call into the outer layers as to what to do.
no major operational changes were made. The three core object->memq loops
were moved into a single inline procedure and various operational
characteristics of the collapse function were documented.
Do not modify m_len before passing mbuf chains to bpf.
Don't forget to pass packets to bpf when running in Crynwr mode (LINK0).
Partially based on a patch by Bill Fenner <fenner@freebsd.org>.
PR: bin/7241
Improved MSP34xx reset for bt848 Hauppauge boards.
Added detection for Bt848a.
Vsevolod Lobko<seva@sevasoft.alex-ua.com> added more XUSSR channels.
Submitted by: parts from Vsevolod Lobko<seva@sevasoft.alex-ua.com>
Obtained from: parts from OpenBSD
Divert was not feeding clean data to ifa_ifwithaddr() so it was
giving bad results.
Submitted by: kseel <kseel@utcorp.com>, Ruslan Ermilov <ru@ucb.crimea.ua>
