- Switch to using critical_enter/exit instead of save/disable/restore_intr.
- Disable interrupts in Debugger().
This second change wasn't really supposed to go in, but since it's in
there and is useful so that one doesn't get spammed with clock interrupts
while in ddb, I'll leave it in unless people want it reverted.
- If there is no gdb device, just return without trying to return any
value since gdb_handle_exception() returns void.
- When calling prom_halt(), pass in a value telling it to actually halt
and not to randomly choose whether or not to halt or reboot depending on
whatever value happened to be in a0 when the call was made.
an AST results in a signal being delivered, we'll need to do a full register
restore so as to properly setup the signal handler. This is somewhat of
a pessimization, because ast() will be called twice in this case.
This fixes several problems that have been reported where signal intensive
userland apps (most notably dump) have been SEGV'ing for no fault of their
own.
Thanks to Peter Jeremy <peter.jeremy@alcatel.com.au> for presenting the
AST scenario which led to me fiinally figuring this out.
Reviewed by: jhb
fseeko(file_size, SEEK_SET) -> fseek(0L, SEEK_END)
1) File may grows between operations, so fseeko to file_size may miss
2) 0L, SEEK_END is the same code using in tail in all other places
method anymore since the code inside the RPC library has changed too much.
Now that the clnt_dg module has the necessary code internally, we can yank
out the local method code and turn on the ASYNC hack with clnt_control().
This will make the -m flag work again.
to make asynchronous RPCs. This is needed to help fix ypbind, which can no
longer override the clnt_dg_call() method (formerly the clntudp_call()
method) due to all the internal descriptor locking code in TI-RPC. Turning
on this flag allows us to send an RPC request, then return immediately,
and handle a reply later, rather than being forced to do the request
and reply in a single function call.
Also fix a byte ordering bug: when clnt_dg_call() increments the XID
prior to transmitting a request, it uses the raw value, which is wrong.
The XID is stored in network byte order, i.e. big-endian. The CLSET_XID
and CLGET_XID commands in clnt_dg_control() use ntohl()/htonl() to get
the byte ordering right, but because clnt_dg_call() does not do this,
using CLSET_XID/CLGET_XID doesn't actually work, unless you're on a
big endian host, which we aren't (yet). Fix clnt_dg_call() to byte swap
properly when doing the increment.
process we're looking for. (I don't think this can currently
happen, but it depends how the function is called).
PR: 25932
Submitted by: David Xu <davidx@viasoft.com.cn>
The PAM_FAIL_CHECK and PAM_END macros in su.c came from the util-linux
package's PAM patches to the BSD login.c
Submitted by: "David J. MacKenzie" <djm@web.us.uu.net>
If one is trying to dump or repair an ill system, give the user a fighting
chance. Refusing to operate w/o a very non-critical file (feature) is
just plain stupid.
The fixes the problem of PLAY_BIG not being implemented on
some modern drives.
The problem now is that some old drives use BSD encoding
in the MSF case, which they dont tell, and which is also
not according to spec *sigh*. Hopefully there are not
too many of those still alive, or I hereby grant
license to kill the firmware writers that wrote the mess.
Some of the major changes include:
- The SCSI error handling portion of cam_periph_error() has
been broken out into a number of subfunctions to better
modularize the code that handles the hierarchy of SCSI errors.
As a result, the code is now much easier to read.
- String handling and error printing has been significantly
revamped. We now use sbufs to do string formatting instead
of using printfs (for the kernel) and snprintf/strncat (for
userland) as before.
There is a new catchall error printing routine,
cam_error_print() and its string-based counterpart,
cam_error_string() that allow the kernel and userland
applications to pass in a CCB and have errors printed out
properly, whether or not they're SCSI errors. Among other
things, this helped eliminate a fair amount of duplicate code
in camcontrol.
We now print out more information than before, including
the CAM status and SCSI status and the error recovery action
taken to remedy the problem.
- sbufs are now available in userland, via libsbuf. This
change was necessary since most of the error printing code
is shared between libcam and the kernel.
- A new transfer settings interface is included in this checkin.
This code is #ifdef'ed out, and is primarily intended to aid
discussion with HBA driver authors on the final form the
interface should take. There is example code in the ahc(4)
driver that implements the HBA driver side of the new
interface. The new transfer settings code won't be enabled
until we're ready to switch all HBA drivers over to the new
interface.
src/Makefile.inc1,
lib/Makefile: Add libsbuf. It must be built before libcam,
since libcam uses sbuf routines.
libcam/Makefile: libcam now depends on libsbuf.
libsbuf/Makefile: Add a makefile for libsbuf. This pulls in the
sbuf sources from sys/kern.
bsd.libnames.mk: Add LIBSBUF.
camcontrol/Makefile: Add -lsbuf. Since camcontrol is statically
linked, we can't depend on the dynamic linker
to pull in libsbuf.
camcontrol.c: Use cam_error_print() instead of checking for
CAM_SCSI_STATUS_ERROR on every failed CCB.
sbuf.9: Change the prototypes for sbuf_cat() and
sbuf_cpy() so that the source string is now a
const char *. This is more in line wth the
standard system string functions, and helps
eliminate warnings when dealing with a const
source buffer.
Fix a typo.
cam.c: Add description strings for the various CAM
error status values, as well as routines to
look up those strings.
Add new cam_error_string() and
cam_error_print() routines for userland and
the kernel.
cam.h: Add a new CAM flag, CAM_RETRY_SELTO.
Add enumerated types for the various options
available with cam_error_print() and
cam_error_string().
cam_ccb.h: Add new transfer negotiation structures/types.
Change inq_len in the ccb_getdev structure to
be "reserved". This field has never been
filled in, and will be removed when we next
bump the CAM version.
cam_debug.h: Fix typo.
cam_periph.c: Modularize cam_periph_error(). The SCSI error
handling part of cam_periph_error() is now
in camperiphscsistatuserror() and
camperiphscsisenseerror().
In cam_periph_lock(), increase the reference
count on the periph while we wait for our lock
attempt to succeed so that the periph won't go
away while we're sleeping.
cam_xpt.c: Add new transfer negotiation code. (ifdefed
out)
Add a new function, xpt_path_string(). This
is a string/sbuf analog to xpt_print_path().
scsi_all.c: Revamp string handing and error printing code.
We now use sbufs for much of the string
formatting code. More of that code is shared
between userland the kernel.
scsi_all.h: Get rid of SS_TURSTART, it wasn't terribly
useful in the first place.
Add a new error action, SS_REQSENSE. (Send a
request sense and then retry the command.)
This is useful when the controller hasn't
performed autosense for some reason.
Change the default actions around a bit.
scsi_cd.c,
scsi_da.c,
scsi_pt.c,
scsi_ses.c: SF_RETRY_SELTO -> CAM_RETRY_SELTO. Selection
timeouts shouldn't be covered by a sense flag.
scsi_pass.[ch]: SF_RETRY_SELTO -> CAM_RETRY_SELTO.
Get rid of the last vestiges of a read/write
interface.
libkern/bsearch.c,
sys/libkern.h,
conf/files: Add bsearch.c, which is needed for some of the
new table lookup routines.
aic7xxx_freebsd.c: Define AHC_NEW_TRAN_SETTINGS if
CAM_NEW_TRAN_CODE is defined.
sbuf.h,
subr_sbuf.c: Add the appropriate #ifdefs so sbufs can
compile and run in userland.
Change sbuf_printf() to use vsnprintf()
instead of kvprintf(), which is only available
in the kernel.
Change the source string for sbuf_cpy() and
sbuf_cat() to be a const char *.
Add __BEGIN_DECLS and __END_DECLS around
function prototypes since they're now exported
to userland.
kdump/mkioctls: Include stdio.h before cam.h since cam.h now
includes a function with a FILE * argument.
Submitted by: gibbs (mostly)
Reviewed by: jdp, marcel (libsbuf makefile changes)
Reviewed by: des (sbuf changes)
Reviewed by: ken
