Make the umass driver depend on this module.
Makes it possible to compile the kernel without SCSI support and load it
when for example a USB floppy is conencted.
Bring back the CAM_NEGOTIATE ccb flag. This flag indicates
that SPI transfer negotiation should occur concurrently with the
execution of this CCB. The flag is not yet used by the XPT but
is required for proper support of multi-initiator configurations
where topology scans cannot rely on a bus reset to invalidate
prior negotiations.
cam_xpt.c:
Don't allow DT transmission rates to be specified for devices
that don't have the DT feature listed in their inquiry data.
kernel. Justin agress that there is no other reasonable alternative to
do automatic rescans on connect.
The problem is that when a new device attaches to a SIM (SCSI host
controller) we need to send a XPT_SCAN_BUS command to the SIM using
xpt_action. This requires however that there is a peripheral available
to take the command (otherwise xpt_done and later bomb). The RESCAN
ioctl uses the same periph.
This enables a USB mass storage drive to do an automatic rescan on
connection of the drive.
The automatic dropping of a CAM entry on disconnection was already
working (asynchronous event).
The next thing to do is find someone to commit a change to vpo to do the
same thing. Just port umass_cam_rescan and friends across to that
driver.
Approved by: gibbs
dynamic resource tables rather than relying on a duplicated cam-specific
table generated by config(8) in ioconf.c. This was a major holdup to
getting loader / userconfig driven configuration of scsi wiring.
structure. Remove usage of the (now gone) pd_type tag of same.
Add an extra probing state such that if we successfully run an
initial inquiry (36 bytes), rerun another one with a longer data
size as informed by the 'additional length' field in the first
returned inquiry data (making sure not to get bigger than the
actual scsi_inquiry_data structure- which has also been modified-
see separate checkin of scsi_all.h). This allows devices such
as SAF-TE devices (which have identifying marks in offsets 48-53
in inquiry data) to be successfully found without special case
inquiry commands. There are also a lot of other things such as
version codes that are coming in in the SPC2 specification that it
would be useful to get our hands on.
Reviewed by: gibbs@freebsd.org, ken@freebsd.org
Clean up node creation in the EDT so that initialization follows member
declaration.
Sort registered paths by pathid so that we probe busses in order of
ascending pathid. This makes hardwiring of busses without wiring
individual targets do what the user expects. (submitted by tegge@FreeBSD.org)
Fix an EDT node leak. Target nodes would never go away.
Implement xpt_bus_deregister().
(prodded by some patches from T. Ichinoseki, but implemented differently.)
camcontrol was setup to use the old scheme of going through the xpt(4)
device, which never worked properly (and has been disabled for a while).
camcontrol now sends BDRs through the pass(4) device, and XPT_RESET_DEV
CCBs are put on the device queue in the transport layer, as they should be.
Submitted by: luoqi
Reviewed by: ken
- Move intrhook stuff into kernel.h
- Remove all occurrences of #device <device.h>
- Add kernel.h were necessary (nowhere)
- delete device.h
This file contained the structures for cfdata (old style config) and is no
longer used. It was included by most drivers.
It confuses the remote debugger as the definition of 'struct device' in
device.h is found before the one in bus_private.h.
have been there in the first place. A GENERIC kernel shrinks almost 1k.
Add a slightly different safetybelt under nostop for tty drivers.
Add some missing FreeBSD tags
Diskslice/label code not yet handled.
Vinum, i4b, alpha, pc98 not dealt with (left to respective Maintainers)
Add the correct hook for devfs to kern_conf.c
The net result of this excercise is that a lot less files depends on DEVFS,
and devtoname() gets more sensible output in many cases.
A few drivers had minor additional cleanups performed relating to cdevsw
registration.
A few drivers don't register a cdevsw{} anymore, but only use make_dev().
Clear residuals for XPT_TARGET_IO/XPT_CONT_TARGET_IO calls just
as we do for XPT_SCSI_IO calls.
Make xpt_release_devq a proper reciprocal of xpt_freeze_devq by
allowing the caller to decrement the count more than once per call.
Change the semantics of xpt_path_cmp to return 1 for a match
with a wildcard from path1 and 2 for a match with wildcards
from path2. This change doesn't affect most callers as they
only check for >=0 (exact match or one containing a wildcard).
When cleaning up a device node, ensure that there are no timeouts
outstanding that reference it.
is quirked for allowing it. This will allow SCSI cards to specify their true
correct lun width (32 for Qlogic SCSI, 16 or 65536 for Qlogic Fibre Channel)
without crippling the system because of f/w breakage of a lot of drives.
Reviewed by: gibbs@freebsd.org
The cdevsw_add() function now finds the major number(s) in the
struct cdevsw passed to it. cdevsw_add_generic() is no longer
needed, cdevsw_add() does the same thing.
cdevsw_add() will print an message if the d_maj field looks bogus.
Remove nblkdev and nchrdev variables. Most places they were used
bogusly. Instead check a dev_t for validity by seeing if devsw()
or bdevsw() returns NULL.
Move bdevsw() and devsw() functions to kern/kern_conf.c
Bump __FreeBSD_version to 400006
This commit removes:
72 bogus makedev() calls
26 bogus SYSINIT functions
if_xe.c bogusly accessed cdevsw[], author/maintainer please fix.
I4b and vinum not changed. Patches emailed to authors. LINT
probably broken until they catch up.
Reformat and initialize correctly all "struct cdevsw".
Initialize the d_maj and d_bmaj fields.
The d_reset field was not removed, although it is never used.
I used a program to do most of this, so all the files now use the
same consistent format. Please keep it that way.
Vinum and i4b not modified, patches emailed to respective authors.
The XPT doesn't have a problem with this itself, but some controllers
drivers may have been caught off guard by the old behavior.
XPT_CONT_TARGET_IO is also a valid ccb type for cam_periph_unmapmem.
types allow the reporting of error counts and other statistics. Currently
we provide information on the last BDR or bus reset as well as active
transaction inforamtion, but this will be expanded as more information is
added to aid in error recovery.
Use the 'last reset' information to better handle bus settle delays.
Peripheral drivers now control whether a bus settle delay occurs and
for how long. This allows target mode peripheral drivers to avoid
having their device queue frozen by the XPT for what shoudl only be
initiator type behavior.
Don't perform a bus reset if the target device is incapable of performing
transfer negotiation (e.g. Fiber Channel).
If we don't perform a bus reset but the controller is capable of transfer
negotiations, force negotiations on the first transaction to go to the
device. This ensures that we aren't tripped up by a left over negotiation
from the prom, BIOS, loader, etc.
Add a default async handler funstion to cam_periph.c to remove duplicated
code in all initiator type peripheral drivers.
Allow mapping of XPT_CONT_TARGET_IO ccbs from userland. They are
itentical to XPT_SCSI_IO ccbs as far as data mapping is concerned.
NOTE: These changes will require recompilation of any userland
applications, like cdrecord, xmcd, etc., that use the CAM passthrough
interface. A make world is recommended.
camcontrol.[c8]:
- We now support two new commands, "tags" and "negotiate".
- The tags commands allows users to view the number of tagged
openings for a device as well as a number of other related
parameters, and it allows users to set tagged openings for
a device.
- The negotiate command allows users to enable and disable
disconnection and tagged queueing, set sync rates, offsets
and bus width. Note that not all of those features are
available for all controllers. Only the adv, ahc, and ncr
drivers fully support all of the features at this point.
Some cards do not allow the setting of sync rates, offsets and
the like, and some of the drivers don't have any facilities to
do so. Some drivers, like the adw driver, only support enabling
or disabling sync negotiation, but do not support setting sync
rates.
- new description in the camcontrol man page of how to format a disk
- cleanup of the camcontrol inquiry command
- add support in the 'devlist' command for skipping unconfigured devices if
-v was not specified on the command line.
- make use of the new base_transfer_speed in the path inquiry CCB.
- fix CCB bzero cases
cam_xpt.c, cam_sim.[ch], cam_ccb.h:
- new flags on many CCB function codes to designate whether they're
non-immediate, use a user-supplied CCB, and can only be passed from
userland programs via the xpt device. Use these flags in the transport
layer and pass driver to categorize CCBs.
- new flag in the transport layer device matching code for device nodes
that indicates whether a device is unconfigured
- bump the CAM version from 0x10 to 0x11
- Change the CAM ioctls to use the version as their group code, so we can
force users to recompile code even when the CCB size doesn't change.
- add + fill in a new value in the path inquiry CCB, base_transfer_speed.
Remove a corresponding field from the cam_sim structure, and add code to
every SIM to set this field to the proper value.
- Fix the set transfer settings code in the transport layer.
scsi_cd.c:
- make some variables volatile instead of just casting them in various
places
- fix a race condition in the changer code
- attach unless we get a "logical unit not supported" error. This should
fix all of the cases where people have devices that return weird errors
when they don't have media in the drive.
scsi_da.c:
- attach unless we get a "logical unit not supported" error
scsi_pass.c:
- for immediate CCBs, just malloc a CCB to send the user request in. This
gets rid of the 'held' count problem in camcontrol tags.
scsi_pass.h:
- change the CAM ioctls to use the CAM version as their group code.
adv driver:
- Allow changing the sync rate and offset separately.
adw driver
- Allow changing the sync rate and offset separately.
aha driver:
- Don't return CAM_REQ_CMP for SET_TRAN_SETTINGS CCBs.
ahc driver:
- Allow setting offset and sync rate separately
bt driver:
- Don't return CAM_REQ_CMP for SET_TRAN_SETTINGS CCBs.
NCR driver:
- Fix the ultra/ultra 2 negotiation bug
- allow setting both the sync rate and offset separately
Other HBA drivers:
- Put code in to set the base_transfer_speed field for
XPT_GET_TRAN_SETTINGS CCBs.
Reviewed by: gibbs, mjacob (isp), imp (aha)
Interrupts under the new scheme are managed by the i386 nexus with the
awareness of the resource manager. There is further room for optimizing
the interfaces still. All the users of register_intr()/intr_create()
should be gone, with the exception of pcic and i386/isa/clock.c.
Move handling of CAM_AUTOSENSE_FAIL into block dealing with
all other scsi status errors.
cam_queue.c:
cam_queue.h:
Fix 'off by one' heap bug in a more efficient manner. Since
heap algorithms like to deal with indexes started from 1,
offset our heap array pointer at allocation time to make this
so for a C environment. This makes the implementation of the
algorithm a bit more efficient.
cam_xpt.c:
Use macros for accessing the head of the heap so that code
is isolated from implementation details of the heap.
write performance when tagged queueing is enabled.
Although the PR was submitted for the 4 gig version of this drive, the
assumption is that the 2 gig version has the same problem. Therefore
tagged queueing is disabled for both.
Also, update the comment for the Western Digital Enterprise drives to note
that the best performance for those drives is achieved when tagged queueing
is disabled and write caching is enabled.
PR: kern/10398
Submitted by: Hideaki Okada <hokada@isl.melco.co.jp>
trouble with tagged queueing as the 6.5 gig version.
So, I've added a quirk entry for it to limit it to two outstanding
transactions at a time, just like the 6.5G version. While I'm at it, add a
quirk for the 9G version of the drive, since it most likely has the same
problem.
Submitted by: Jeremy Lea <reg@shale.csir.co.za>
caused by temporary EDT allocations performed by controller drivers in
their interrupt routiens.
Reference count bus entries in the EDT in preparation for support for
dynamic controller arrival and departure.
Have children of the EDT hold references to their parents.
Correct routing of the XPT_IMMED_NOTIFY ccb type for use in
target mode applications.
Fix a few cases where the generation count for EDT data members was
not being updated when a modification occurred.
splcam() problem Noticed by: Tor Egge <tegge@FreeBSD.org>
drive has very poor write performance (1.4MB/sec vs. 12MB/sec) with anything
more than two oustanding transactions.
So, this limits the number of tagged commands to two for that drive.
Thanks to Paul van der Zwan for doing a whole lot of testing to confirm
this.
Reported by: Paul van der Zwan <paulz@trantor.xs4all.nl>
Sync rates like 4.032MHz were getting printed as 4.32MHz.
Also, add a quirk entry for the 18G Quantum Atlas III. Like most other
recent Quantum drives, it bogusly reports queue full. Thanks to Andre
Albsmeier <andre.albsmeier@mchp.siemens.de> for the Atlas III inquiry
information.
Reviewed by: gibbs
