required by video card drivers. Specifically, this change introduces
vm_cache_mode_t with an appropriate VM_CACHE_DEFAULT definition on all
architectures. In addition, this changes adds a vm_cache_mode_t parameter
to kmem_alloc_contig() and vm_phys_alloc_contig(). These will be the
interfaces for allocating mapped kernel memory and physical memory,
respectively, with non-default cache modes.
In collaboration with: jhb
- Modules and kernel code alike may use DPCPU_DEFINE(),
DPCPU_GET(), DPCPU_SET(), etc. akin to the statically defined
PCPU_*. Requires only one extra instruction more than PCPU_* and is
virtually the same as __thread for builtin and much faster for shared
objects. DPCPU variables can be initialized when defined.
- Modules are supported by relocating the module's per-cpu linker set
over space reserved in the kernel. Modules may fail to load if there
is insufficient space available.
- Track space available for modules with a one-off extent allocator.
Free may block for memory to allocate space for an extent.
Reviewed by: jhb, rwatson, kan, sam, grehan, marius, marcel, stas
pv entries surpasses the high water mark. The problem was that the page
daemon would only be awakened the first time that the high water mark was
surpassed. (The variable "pagedaemon_waken" is a non-working vestige of
FreeBSD 4.x, in which it was external and reset by the page daemon whenever
it ran. This reset allowed subsequent wakeups by the pv entry allocator.)
aim/machdep.c:
- the RI status register bit needs to be set when doing the mtmsrd 64-bit
instruction test
- psim doesn't implement the dcbz instruction so the run-time cacheline
test fails. Set the cachline size to 32 to avoid infinite loops in
future calls to __syncicache()
aim/platform_chrp.c:
- if after iterating through / and a name property of "cpus" still isn't
found, just search directly for '/cpus'.
- psim doesn't put a "reg" property on it's cpu nodes, so assume 0
since it is uniprocessor-only at this point
powerpc/openpic.c
- the number of CPUs reported is 1 too many on psim's openpic
Reviewed by: nwhitehorn
MFC after: 1 week (openpic part)
in Freescale system-on-chip devices.
The following algorithms and schemes are currently supported:
- 3DES, AES, DES
- MD5, SHA1, SHA256, SHA384, SHA512
Reviewed by: philip
Obtained from: Freescale, Semihalf
Without this fix pte_vatopa() was not able to retrieve physical address of
data structures inside kernel, for example EFAULT was reported while acessing
/dev/kmem ('netstat -nr').
Submitted by: Piotr Ziecik
Obtained from: Semihalf
goal of shipping 8.0 with MAC support in the default kernel. No policies
will be compiled in or enabled by default, but it will now be possible to
load them at boot or runtime without a kernel recompile.
While the framework is not believed to impose measurable overhead when no
policies are loaded (a result of optimization over the past few months in
HEAD), we'll continue to benchmark and optimize as the release approaches.
Please keep an eye out for performance or functionality regressions that
could be a result of this change.
Approved by: re (kensmith)
Obtained from: TrustedBSD Project
access windows. This eliminates hangs on systems which are configured to use
interleaved mode: prior to this fix we were simply cutting ourselves from
access to the main memory in this case.
Obtained from: Freescale, Semihalf
possible future I-cache coherency operation can succeed. On ARM
for example the L1 cache can be (is) virtually mapped, which
means that any I/O that uses temporary mappings will not see the
I-cache made coherent. On ia64 a similar behaviour has been
observed. By flushing the D-cache, execution of binaries backed
by md(4) and/or NFS work reliably.
For Book-E (powerpc), execution over NFS exhibits SIGILL once in
a while as well, though cpu_flush_dcache() hasn't been implemented
yet.
Doing an explicit D-cache flush as part of the non-DMA based I/O
read operation eliminates the need to do it as part of the
I-cache coherency operation itself and as such avoids pessimizing
the DMA-based I/O read operations for which D-cache are already
flushed/invalidated. It also allows future optimizations whereby
the bcopy() followed by the D-cache flush can be integrated in a
single operation, which could be implemented using on-chips DMA
engines, by-passing the D-cache altogether.
- make mftb() shared, rewrite in C, provide complementary mttb()
- adjust SMP startup per the above, additional comments, minor naming
changes
- eliminate redundant TB defines, other minor cosmetics
Reviewed by: marcel, nwhitehorn
Obtained from: Freescale, Semihalf
new platform module. These are probed in early boot, and have the
responsibility of determining the layout of physical memory, determining
the CPU timebase frequency, and handling the zoo of SMP mechanisms
found on PowerPC.
Reviewed by: marcel, raj
Book-E parts by: raj
When memory is not zero'ed by firmware, uninitialized PCB can have bogus
contents, which appear as a saved onfault condition, Altivec context to
restore etc. and lead to corruption/crashes. This commit fixes such issues.
Submitted by: Michal Mazur arg ! semihalf dot com
Tested by: Andreas Tobler andreast-list ! fgznet dot ch
controller in the VIA southbridge functional in the CDS
(Configurable Development System) for MPC85XX.
The embedded USB controllers look operational but the
interrupt steering is still wrong.
Include opt_ddb.h for that. Now you can actually boot with
-d and set breakpoints using function names.
o Make sure to include opt_msgbuf.h.
o Carve out the first 1MB of physical memory. The MPC85xx has
DMA problems with addresses below 1MB. Ideally busdma knows
how to avoid allocating below 1MB for MPC85xx, but that
requires a bit more work. For now, ignore the 1MB of DRAM.
a fair number of static data structures, making this an unlikely
option to try to change without also changing source code. [1]
Change default cache line size on ia64, sparc64, and sun4v to 128
bytes, as this was what rtld-elf was already using on those
platforms. [2]
Suggested by: bde [1], jhb [2]
MFC after: 2 weeks
CACHE_LINE_SIZE constant. These constants are intended to
over-estimate the cache line size, and be used at compile-time
when a run-time tuning alternative isn't appropriate or
available.
Defaults for all architectures are 64 bytes, except powerpc
where it is 128 bytes (used on G5 systems).
MFC after: 2 weeks
Discussed on: arch@
replace magic numbers with constants to keep this from happening again.
Without this fix, some programs would occasionally get SIGTRAP instead
of SIGILL on an illegal instruction. This affected Altivec detection
in pixman, and possibly other software.
Reported by: Andreas Tobler
MFC after: 1 week
