gif/faith/stf moved to 0xfN entries, since their previous location
is allocated to some other interfaces.
Also add the IFT_PVC, which is the ATM PVC subinterface from ALTQ.
This also syncs us up a bit to NetBSD again.
This change requires a total recompilation of all kmem users, as
itojun told me.
Next in line is synching to the IANI SMI list.
Approved by: itojun
Add spl/splx to various sensitive spots
Change semantics of the vmnet version of the device to keep VMware happy
(don't junk state when the device is closed)
Submitted by: vsilyaev@mindspring.com
delete the cloned route that is associated with the connection.
This does not exhaust the routing table memory when the system
is under a SYN flood attack. The route entry is not deleted if there
is any prior information cached in it.
Reviewed by: Peter Wemm,asmodai
configurations include loadable interfaces. After loading new
interface drivers, perform a 'sysctl -w net.link.ether.bridge_refresh=1'
and the bridge code will reinitialize itself.
Submitted by: <vsilyaev@mindspring.com>
The tap driver is used to present a virtual Ethernet interface to the
system. Packets presented by the network stack to the interface are
made available to a character device in /dev. With tap and the bridge
code, you can make remote bridge configurations where both sides of
the bridge are separated by userland daemons.
This driver also has a special naming hack to allow it to serve a similar
purpose to the vmware port.
Submitted by: myevmenkin@att.com, vsilyaev@mindspring.com
ether_ifdetach().
The former consolidates the operations of if_attach(), ng_ether_attach(),
and bpfattach(). The latter consolidates the corresponding detach operations.
Reviewed by: julian, freebsd-net
This means 'options NETGRAPH' is no longer necessary in order to get
netgraph-enabled Ethernet interfaces. This supports loading/unloading
the ng_ether.ko and attaching/detaching the Ethernet interface in any
order.
Add two new hooks 'upper' and 'lower' to allow access to the protocol
demux engine and the raw device, respectively. This enables bridging
to be defined as a netgraph node, if so desired.
Reviewed by: freebsd-net@freebsd.org
address on an interface. This basically allows you to do what my
little setmac module/utility does via ifconfig. This involves the
following changes:
socket.h: define SIOCSIFLLADDR
if.c: add support for SIOCSIFLLADDR, which resets the values in
the arpcom struct and sockaddr_dl for the specified interface.
Note that if the interface is already up, we need to down/up
it in order to program the underlying hardware's receive filter.
ifconfig.c: add lladdr command
ifconfig.8: document lladdr command
You can now force the MAC address on any ethernet interface to be
whatever you want. (The change is not sticky across reboots of course:
we don't actually reprogram the EEPROM or anything.) Actually, you
can reprogram the MAC address on other kinds of interfaces too; this
shouldn't be ethernet-specific (though at the moment it's limited to
6 bytes of address data).
Nobody ran up to me and said "this is the politically correct way to
do this!" so I don't want to hear any complaints from people who think
I could have done it more elegantly. Consider yourselves lucky I didn't
do it by having ifconfig tread all over /dev/kmem.
m_adj() and then check the resulting mbuf for misalignment, copying
backwards to align the mbuf if required.
This fixes a longstanding problem where an mbuf which would have been
properly aligned after an m_adj() was being misaligned and causing an
unaligned access trap in ip_input(). This bug only triggered when booting
diskless.
Reviewed by: dfr
of the individual drivers and into the common routine ether_input().
Also, remove the (incomplete) hack for matching ethernet headers
in the ip_fw code.
The good news: net result of 1016 lines removed, and this should make
bridging now work with *all* Ethernet drivers.
The bad news: it's nearly impossible to test every driver, especially
for bridging, and I was unable to get much testing help on the mailing
lists.
Reviewed by: freebsd-net
search routine, and scratching our heads over why it was so obfuscated.
This delta fixes a number of confusing style bugs and renames several
structure members to have more meaningful names. There remain a number
of odd control-flow structures. These changes do not affect the generated
code.
would be returned with a wrong value.
While we're here, get rid of unnecessary panic call.
PR: 17311, 12996, 14457
Submitted by: Patrick Bihan-Faou <patrick@mindstep.com>,
Kris Kennaway <kris@FreeBSD.org>
From the README:
Any IEEE 802.11 cards use AMD Am79C930 and Harris (Intersil) Chipset
with PCnetMobile firmware by AMD.
BayStack 650 1Mbps Frequency Hopping PCCARD adapter
BayStack 660 2Mbps Direct Sequence PCCARD adapter
Icom SL-200 2Mbps Direct Sequence PCCARD adapter
Melco WLI-PCM 2Mbps Direct Sequence PCCARD adapter
NEL SSMagic 2Mbps Direct Sequence PCCARD adapter
Netwave AirSurfer Plus
1Mbps Frequency Hopping PCCARD adapter
Netwave AirSurfer Pro
2Mbps Direct Sequence PCCARD adapter
Known Problems:
WEP is not supported.
Does not create IBSS itself.
Cannot configure the following on FreeBSD:
selection of infrastructure/adhoc mode
ESSID
...
Submitted by: Atsushi Onoe <onoe@sm.sony.co.jp>
It was not a good idea to remove csu_header from struct cspace, it had
ramifications which I didn't notice.
Restore src/usr.sbin/ppp/slcompress.h to the way it was, since MAX_HDR
was already defined as 128 there and it's a user program anyway.
In sys/net/slcompress.h make MAX_HDR 128 intead of MLEN to avoid
bloat.
My apologies for any inconvenience.
