messages, abort messages, and abort tag messages.
Fix a bug in how default transfer negotiations are handled if the
user had disabled initial bus resets.
Support multi-targetid on the aic7895C.
format_config: code preening.
vinum_scandisk: If we find a partition in the first pass over a drive,
note the fact so we don't grab the compatibility partition as well.
Submitted-by: peter
the aic7890/91/96/97 cards. This could cause the system to go into
a long retry/recovery loop during probe.
Fix the alignment argument to bus_dma_tag_create().
Don't set the CACHETHEN bit in dscommand0 for Ultra2 controllers
until we know more about its behavior. The description for this
bit makes it sound like it could cause problems with certain
PCI chipsets.
goes into initialized state, not 'up'. This makes it easier to ensure
consistency in multi-plex volumes.
update_plex_state: redo transitions from empty and initialized
subdisks to up or reviving, depending on the number of plexes.
Reported-by: Bernd Walter <ticso@cicely.de>
Remy Nonnenmacher <remy@synx.com>
Introduce BUF_STRATEGY(struct buf *, int flag) macro, and use it throughout.
please see comment in sys/conf.h about the flag argument.
Remove strategy argument from all the diskslice/label/bad144
implementations, it should be found from the dev_t.
Remove bogus and unused strategy1 routines.
Remove open/close arguments from dssize(). Pick them up from dev_t.
Remove unused and unfinished setgeom support from diskslice/label/bad144 code.
Don't return "can't do it" when the user requests a state change to
the current state. This previously caused silly messages like "Can't
start <foo>: invalid argument", when in fact <foo> was already
started.
set_plex_state: don't set state for non-existent plexes.
update_plex_status: as long as we have initializing subdisks, we're
initializing.
Move the declaration of freerq() to request.h.
logrq: add support for lock events.
vinumstart: solve a problem where removing a plex from an active
volume could cause attempts to access non-existent plexes.
launch_requests: don't set a request group active until we're sure we
can launch it. This caused some hangs under unusual
circumstances.
bre: don't set XFR_BAD_SUBDISK if we're not going to use it.
build_read_request: correct recovery, which caused some hangs under
(other) unusual circumstances.
build_rq_buffer: don't set bp->b_dev if we don't have a dev.
sdio: clean up, remove obsolete code.
deallocrqg: unlock any locks the rqg may have.
bre5:
Shorten some lines.
Desired-by: bde
If we're reading from a short plex, return EOF indication.
Always lock the stripe before starting a transfer. Hopefully the
current version will solve some data integrity problems that have
been reported with degraded RAID-5 plexes.
Reported-by: Bernd Walter <ticso@cicely.de>
Remy Nonnenmacher <remy@synx.com>
solve some data integrity problems that have been reported with
degraded RAID-5 plexes.
Reported-by: Bernd Walter <ticso@cicely.de>
Remy Nonnenmacher <remy@synx.com>
Tidy other comments.
open_drive: don't call set_drive_state if we decide to take it down.
This could help avoid some race conditions with the daemon.
init_drive: don't set the drive down, we'll let close_locked_drive do
that.
close_locked_drive: set drive state to down without calling
set_drive_state. This could help avoid some race conditions with the
daemon.
driveio: remove the function, it wasn't being used.
get_volume_label: remove volume dependencies so that we can return a
label for plexes and subdisks as well. What a kludge.
Remove declarations for freerq and free_rqg.
Remove DEBUG_RESID code.
freerq: check whether the request is holding a lock, free if so.
free_rqg: remove. It wasn't being used any more.
Change the Debugger calls to panics.
checkdiskconfig(): remove. It didn't make any sense to complain about
kernel keywords in user config files; it just made it more difficult
to convert. Now we ignore kernel keywords if we're not in kernel
mode.
get_empty_sd: initialize sectors.
free_drive: don't close if we don't have a vp. Maybe this will help
fix the problem that peter had, but I wouldn't count on it.
config_plex: If the plex is RAID-5, give it a rangelock structure.
start_config: Reset current drive, plex and volume so that a new
'create' command doesn't get long-dead defaults.
struct rqelement, enum rqinfo_type, struct rqinfo, union rqinfou: add
lock requests.
Add declarations for freerq and unlockrange. Since they include
request structures, they can't go in vinumext.h
a module. Also modified the code to work on FreeBSD/alpha and added
device vr0 to the alpha GENERIC config.
While I was in the neighborhood, I noticed that I was still using
#define NFPX 1 in all of the Makefiles that I'd copied from the fxp
module. I don't really use #define Nfoo X so it didn't matter, but
I decided to customize this correctly anyway.
- %q -> %ll.
Fixed nearby errors not reported by gcc -Wformat on i386's:
- don't assume that the promotion of [u_]int64_t is [u_]quad_t.
- don't use signed formats for unsigned args.
Add Cybernet copyright.
OK'd-by: Chuck Jacobus <chuck@cybernet.com>
update_plex_state:
If any subdisk in the plex is initializing, set the plex to
initializing state. This gets rid of the ugly corrupt/degraded/up
transitions which previously occurred.
Desired-by: Steve Taylor <staylor@cybernet.com>
sddownstate:
Add new function, used by checksdstate.
checksdstate:
Let sddownstate decide what status to return.
Add Cybernet copyright.
OK'd-by: Chuck Jacobus <chuck@cybernet.com>
logrq: save device major and minor numbers to compensate for lost
dev_t.
launch_requests: Don't issue requests which are marked
XFR_BAD_SUBDISK. This may make things easier in bre().
bre:
Rearrange.
- Change some comments
- Recognize holes in plex structure. Formerly this could lead to
incorrect write to the plex. Return REQUEST_DEGRADED on a read
request, but carry on to the bitter end on a write request, and
mark the requests for the inaccessible subdisks with
XFR_BAD_SUBDISK.
- return REQUEST_EOF if the requested transfer goes beyond the end
of the plex. This is not an error, since other plexes may go
further into the volume address space.
build_read_request:
Handle REQUEST_DEGRADED returned from bre().
sdio:
Lock buffer before issuing the requests.
will only accept partitions of type 'vinum'.
format_config: Use the new %q format option in kvprintf, thus getting
rid of some of the filthiest code I've written in a long time. Also
remove the lltoa() function.
With-great-thanks-to: peter
format_config: Accept the fact that a subdisk might not be attached to
a plex, and save the config correctly.
vinum_scandisk: Scan all slices on a drive with a Microsoft partition
table. Only look at the compatibility slice if nothing was found in
the Microsoft slices.
This change removes a frequently employed method of shooting
yourself in the foot: people would decide that the Vinum drives
belonged on their own slice, and they wouldn't be able to start the
subsystem after a reboot. Documentation updates to follow.
initialize subdisks. Probably the plex-related subdisk type will die
a death.
vinumconfig.c:
Accept (and ignore) kernel state information in userland config
files. This saves a lot of error recovery and also makes it possible
to use the output of printconfig to create new configuration.
Remove checkdiskconfig(). It wasn't needed any more.
Start adding support for hot spare drives. You can't put anything on
them (yet).
Change message formats from %lld to %qd.
get_empty_sd: Initialize size to -1. Previously this was done in
config_subdisk, which is the wrong place.
start_config: set current drive, plex and volume to -1, thus stopping
update configurations from taking their defaults from old configs.
now used in f_ops in place of NULL, and modifications to the files
are more carefully ordered. f_ops should also be set to &badfileops
upon "close" of a file.
This does not fix other problems mentioned in this PR than the first
one.
PR: 11629
Reviewed by: peter
eisa_add_intr() which now takes an additional arguement (one of
EISA_TRIGGER_LEVEL or EISA_TRIGGER_EDGE).
The flag RR_SHAREABLE has no effect when passed to
bus_alloc_resource(dev, SYS_RES_IRQ, ...) in an EISA device context as
the eisa_alloc_resource() call (bus_alloc_resource method) now deals
with this flag directly, depending on the device ivars.
This change does nothing more than move all the 'shared = inb(foo + iobsse)'
nonesense to the device probe methods rather than the device attach.
Also, print out 'edge' or 'level' in the IRQ announcement message.
Reviewed by: dfr
- device_print_child() either lets the BUS_PRINT_CHILD
method produce the entire device announcement message or
it prints "foo0: not found\n"
Alter sys/kern/subr_bus.c:bus_generic_print_child() to take on
the previous behavior of device_print_child() (printing the
"foo0: <FooDevice 1.1>" bit of the announce message.)
Provide bus_print_child_header() and bus_print_child_footer()
to actually print the output for bus_generic_print_child().
These functions should be used whenever possible (unless you can
just use bus_generic_print_child())
The BUS_PRINT_CHILD method now returns int instead of void.
Modify everything else that defines or uses a BUS_PRINT_CHILD
method to comply with the above changes.
- Devices are 'on' a bus, not 'at' it.
- If a custom BUS_PRINT_CHILD method does the same thing
as bus_generic_print_child(), use bus_generic_print_child()
- Use device_get_nameunit() instead of both
device_get_name() and device_get_unit()
- All BUS_PRINT_CHILD methods return the number of
characters output.
Reviewed by: dfr, peter
equivalent to SYS_RES_MEMORY for x86 but for alpha, the rman_get_virtual()
address of the resource is initialised to point into either dense-mapped
or bwx-mapped space respectively, allowing direct memory pointers to be
used to device memory.
Reviewed by: Andrew Gallatin <gallatin@cs.duke.edu>
This function is called for each device for which no driver
was found.
Output is similar to the eisa_probe_nomatch() function but with the
added benefit of displaying the assigned IRQ (since PCI gives us
this information up front.)
Output is like so:
pci0: unknown card CPQ0508 (vendor=0x0e11, dev=0x0508) at 11.0 irq 9
pci0: unknown card DFZ0508 (vendor=0x10da, dev=0x0508) at 11.0 irq 9
pci0: unknown card DBL0508 (vendor=0x104c, dev=0x0508) at 11.0 irq 9
pci0: unknown card DDM0011 (vendor=0x108d, dev=0x0011) at 11.0 irq 9
I'm not happy with the 3 lines of macro cruft that got added but
I consider it a temporary annoyance as those bits will be moved to
some place where PCI, EISA and ISAPNP code will be able to use them.
(Not surprisingly, this message is longer than the code in question.)
Reviewed by: peter, dfr
a PCI memory mapped region, rman_get_bushandle() returns what happens
to be a kernel virtual address pointing to the base of the PCI shared
memory window. However this is not the behavior on all platforms:
the only thing you should do with the bushandle is pass it to the
bus_spare_read()/bus_space_write() routines. If you actually do want
the kernel virtual address of the base of the PCI memory window, you
need to use rman_get_virtual().
The problem is that at the moment, rman_get_virtual() returns a physical
address, which is bad. In order to get the kernel virtual address we
need, we have to play with it a little.
Presumeably this behavior will be changed, but in the meantime the
Tigon driver won't work. So for the moment, I'm adding a kludge to
make things happy on the alpha: the correct kernel virtual address
is calculated from the value returned by rman_get_virtual(). This
should be removed once rman_get_virtual() starts doing the right
thing.
This should make the Tigon actuall work on the alpha now.
ethernet controllers based on the AIC-6915 "Starfire" controller chip.
There are single port, dual port and quad port cards, plus one 100baseFX
card. All are 64-bit PCI devices, except one single port model.
The Starfire would be a very nice chip were it not for the fact that
receive buffers have to be longword aligned. This requires buffer
copying in order to achieve proper payload alignment on the alpha.
Payload alignment is enforced on both the alpha and x86 platforms.
The Starfire has several different DMA descriptor formats and transfer
mechanisms. This driver uses frame descriptors for transmission which
can address up to 14 packet fragments, and a single fragment descriptor
for receive. It also uses the producer/consumer model and completion
queues for both transmit and receive. The transmit ring has 128
descriptors and the receive ring has 256.
This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus
so that it can be compiled as a loadable kernel module. Support for BPF
and hardware multicast filtering is included.
critical mbuf fields to sane values. Simplify the use of ETHER_ALIGN to
enforce payload alignment, and turn it on on the x86 as well as alpha
since it helps with NFS which wants the payload to be longword aligned
even though the hardware doesn't require it.
This fixes a problem with the ti driver causing an unaligned access trap
on the Alpha due to m_adj() sometimes not setting the alignment correctly
because of incomplete mbuf initialization.
the driver_t declaration should be "skc" not "sk". Technically, "skc"
is the parent PCI device (the SysKonnect GEnesis controller) and "sk0"
and "sk1" are the network interfaces that get attached to it.
