usb.c: revision 1.39
revision 1.39
date: 2000/02/22 11:30:56; author: augustss; lines: +7 -1
Prepare a little for having USB interrupt processing done
outside the hard interrupt level (in a thread or a softintr).
No real soft processing done yet.
usb.c: revision 1.41
revision 1.41
date: 2000/03/16 00:46:38; author: augustss; lines: +2 -2
Make the USB event queue longer. Mine overflows before the
(user-land) event handler has started. But then I have
about 25 devices connected. :)
ohci.c: revision 1.72 and 1.73
ohcivar.h: revision 1.19 and 1.20
uhci.c: revision 1.85
usbdi.h: a small part of revision 1.40
usbdivar.h: revision 1.47
Relevant commit messages from NetBSD are:
date: 2000/02/22 11:30:54; author: augustss; state: Exp;
Prepare a little for having USB interrupt processing done
outside the hard interrupt level (in a thread or a softintr).
No real soft processing done yet.
----------------------------
date: 2000/02/01 05:42:53; author: augustss; state: Exp;
Put some #ifdefs around power and shutdown hooks.
usb.c: -r1.35 - 1.37
usb_port.h: tiny bit of -r1.26 + an extra bit in the FreeBSD config section.
revision 1.37
date: 2000/01/24 18:35:51; author: thorpej; state: Exp; lines: +7 -1
Use config_pending.
----------------------------
revision 1.36
date: 1999/12/22 23:54:09; author: augustss; state: Exp; lines: +2 -2
Use the flags `locator' to govern if devices are detected early or
late during cold boot.
----------------------------
revision 1.35
date: 1999/12/20 02:12:23; author: augustss; state: Exp; lines: +8 -5
Make sure tsleep() is not called during cold boot.
stead of after
2) Honour NO_TEST_UNIT_READY quirk for atapi devices as well
3) Actually support FujiFilm FinePix 6800 camera's. Will very likely also
work for other FinePix models.
Based on a debug session about half a year ago with Nik Hibma.
MFC after: 2 weeks
extensively as none of my testboxes have speakers or an audio source at
present, but the chains built look correct and reading /dev/audio (ulaw,
translated from signed 16 bit little-endian) gives values within the
expected range for silence.
default format for the chosen subdevice cannot be obtained return an error
instead of returning success with an indeteterminate format selected.
note that this should never happen once the feederchain builder works for
recording.
ohci.c: -r1.69 to 1.71
ohcireg.h: -r1.14
Some of these deltas are based upon patches that we submitted back to
NetBSD. They got manifested slightly differently though, so I've brought
back those differences to bring our code bases closer together.
The logs from the NetBSD version of ohci.c:
revision 1.71
date: 2000/02/01 05:42:52; author: augustss; state: Exp; lines: +13 -2
Put some #ifdefs around power and shutdown hooks.
----------------------------
revision 1.70
date: 2000/01/31 22:35:13; author: augustss; state: Exp; lines: +7 -7
Rename TAILMASK to HEADMASK, since it really masks the head pointer.
From FreeBSD.
----------------------------
revision 1.69
date: 2000/01/31 22:09:13; author: augustss; state: Exp; lines: +18 -14
Change where the has table for physical-to-virtual address translation
is handled. Partly from FreeBSD.
ohci.c: -r1.68
ohcireg.h: -r1.13
date: 2000/01/31 20:17:25; author: augustss; state: Exp;
Fiddle with over-current protect when turning on port power to make
things work for some OHCI controllers.
uhci.c: -r1.82
uhcivar.h: -r1.22
date: 2000/01/26 10:04:39; author: augustss; state: Exp;
Try to avoid accessing the HC if it is dead. Suggested by mycroft.
revision 1.125
date: 2000/09/23 21:00:10; author: augustss; state: Exp; lines: +19 -3
Avoid "bandwidth reclamation" for control transfers. The kue device chokes
on it.
uhci.c: -r1.124
uhcireg.h: -r1.13
date: 2000/08/13 18:20:14; author: augustss; state: Exp;
Fix race condition when unlinking xfers. Thanks to IWAMOTO Toshihiro
<iwamoto@sat.t.u-tokyo.ac.jp> for analyzing the problem and suggesting a fix.
Fixes PR 10662.
uhci.c: -r1.123 (and a tiny bit of -r1.92)
uhcivar.h: -r1.32
date: 2000/08/13 16:18:09; author: augustss; state: Exp;
Implement what in Intel-speech is known as "bandwidth
reclamation". It means that we continously poll USB devices
that have a pending transfer instead of polling just once
every ms. This speeds up some transfers at the expense of
using more PCI bandwidth.
uchireg.h: -r1.12
uchi.c: -r1.121
date: 2000/07/23 19:43:38; author: augustss; state: Exp;
Be a little more explicit and careful about setting links in TDs and QHs.
prior ICP Vortex models. This driver was developed by Achim Leubner
of Intel (previously with ICP Vortex) and Boji Kannanthanam of Intel.
Submitted by: "Kannanthanam, Boji T" <boji.t.kannanthanam@intel.com>
MFC after: 2 weeks
likely looking rate calculation.
Install interrupt handler before calling ich_init as the initialization
occasionally generates spurious interrupts.
These changes are derived from cg's work in progress version of this
driver.
at insert time. When asking gibbs for approval for an MFC, this was
his reply:
1) It leaks memory if it can't allocate a path.
2) It defers allocation of aic->path until the call to scan the
bus. This means the path may be NULL when an interrupt occurs
prior to the call to scan the bus (stray bus reset for instance),
which will lead to a panic.
3) The driver in current doesn't recover from the failure to allocate
aic->path. The driver doesn't check during normal operation if
the path is NULL, so again a panic will result.
4) aic_cam_rescan calls malloc with M_WAITOK. aic_cam_rescan is called
from attach where it isn't necessarily safe to sleep.
5) And most importantly, it co-opts the xpt_periph from the driver level.
This was never part of the design (xpt_periph used to be static). Making
a call of this type may completely confuse the XPT if other XPT operations
are ongoing.
In the long term, Justin and Warner agreed to implement solution where
CAM itself will initiate the bus rescan if a new bus is added. For
the time being (and in particular in light of the upcoming 4.5
release), we now have camcontrol available on the boot floppy, and can
have pccardd initiate the rescan through it.
previous commit, it should always print due to lack of {} around the
second line in the if statement. The message should likely say
something more like "There's no hardware responding at this IRQ.
Device not present (or disbaled)," but that is too long. We generally
don't give elementary advise in device driver messages anyway. Be
that as it may, the problem with it printing all the time should be
corrected.
One to notify the system that the MTU for VLAN can be 1500 so the vlan
will automatically be configured with a 1500 MTU the other is to ignore
the error case if the received frame is to long.
The frame size notification came from code in the SIS driver, and
the support for long frames derived from the NetBSD Tulip driver.
Tested on: 4 port D-Link adapter DFE-570TX 4 Intel 21143
Netgear card with 82c169 PNIC 10/100BaseTX
Reviewed by: ru (manpage), wpaul (not objected to), archie
Approved by: imp
Obtained from: NetBSD
o Remove bogus flags that aren't used (if we need them in the future, we can
add them back).
o Add support for the TI-1031. This is the only YENTA compatible PCI-PCMCIA
bridge that I'm aware of (all the others are PCIC on a PCI bus, which is
different).
Seigo Tanimura (tanimura) posted the initial delta.
I've polished it quite a bit reducing the need for locking and
adapting it for KSE.
Locks:
1 mutex in each filedesc
protects all the fields.
protects "struct file" initialization, while a struct file
is being changed from &badfileops -> &pipeops or something
the filedesc should be locked.
1 mutex in each struct file
protects the refcount fields.
doesn't protect anything else.
the flags used for garbage collection have been moved to
f_gcflag which was the FILLER short, this doesn't need
locking because the garbage collection is a single threaded
container.
could likely be made to use a pool mutex.
1 sx lock for the global filelist.
struct file * fhold(struct file *fp);
/* increments reference count on a file */
struct file * fhold_locked(struct file *fp);
/* like fhold but expects file to locked */
struct file * ffind_hold(struct thread *, int fd);
/* finds the struct file in thread, adds one reference and
returns it unlocked */
struct file * ffind_lock(struct thread *, int fd);
/* ffind_hold, but returns file locked */
I still have to smp-safe the fget cruft, I'll get to that asap.
instead of relying on the previous filters to be present.
Back out r1.125, as a reset is needed to unload any existing microcode,
(which clears the multicast addresses), as it is superceded by this change.
mutex releases to not require flags for the cases when preemption is
not allowed:
The purpose of the MTX_NOSWITCH and SWI_NOSWITCH flags is to prevent
switching to a higher priority thread on mutex releease and swi schedule,
respectively when that switch is not safe. Now that the critical section
API maintains a per-thread nesting count, the kernel can easily check
whether or not it should switch without relying on flags from the
programmer. This fixes a few bugs in that all current callers of
swi_sched() used SWI_NOSWITCH, when in fact, only the ones called from
fast interrupt handlers and the swi_sched of softclock needed this flag.
Note that to ensure that swi_sched()'s in clock and fast interrupt
handlers do not switch, these handlers have to be explicitly wrapped
in critical_enter/exit pairs. Presently, just wrapping the handlers is
sufficient, but in the future with the fully preemptive kernel, the
interrupt must be EOI'd before critical_exit() is called. (critical_exit()
can switch due to a deferred preemption in a fully preemptive kernel.)
I've tested the changes to the interrupt code on i386 and alpha. I have
not tested ia64, but the interrupt code is almost identical to the alpha
code, so I expect it will work fine. PowerPC and ARM do not yet have
interrupt code in the tree so they shouldn't be broken. Sparc64 is
broken, but that's been ok'd by jake and tmm who will be fixing the
interrupt code for sparc64 shortly.
Reviewed by: peter
Tested on: i386, alpha
hw.midi.debug and hw.midi.seq.debug to 1 to enable debug log.
- Make debug messages human-frendly.
- Implement /dev/music.
- Add a timer engine required by /dev/music.
- Fix nonblocking I/O.
- Fix the numbering of midi and synth devices.
firmware to delay completion of commands so that it can attempt to batch
a bunch of completions at once- either returning 16 bit handles in mailbox
registers, or in a resposne queue entry that has a whole wad of 16 bit handles.
Distinguish between 2300 and 2312 chipsets- if only because the revisions
on the chips have different meanings.
Add more instrumentation plus ISP_GET_STATS and ISP_CLR_STATS ioctls.
Run up the maximum number of response queue entities we'll look at
per interrupt.
If we haven't set HBA role yet, always return success from isp_fc_runstate.
MFC after: 2 weeks
date: 2000/02/29 21:37:01; author: augustss; state: Exp;
Distinguish between device and interface classes.
(I finally found a document that said that they were different.)
This gives a bit of a sluggish console, but it prevents the console from
getting stuck if we poll too fast, as well as other badness on certain
machines.
2. Fix a test for != 0 that should have been > 0.
Noticed by: Jamey Wood <Jamey.Wood@Sun.COM> and myself
Submitted by: tmm (2)
- Move from msleep/wakeup to condvar.
- Return either zero or a positive errno value from a function.
Return additional result via references.
- Unify the typedef of callback functions.
Reviewed by: Brooks Davis <brooks@freebsd.org>
Warner Losh <imp@freebsd.org>
Approved by: Brooks Davis <brooks@freebsd.org>
Warner Losh <imp@freebsd.org>
a packed array so sizeof work. This broke RFMON mode and passing
up 802.11 packets.
The Linux emulation code was derived from the open source Linux driver to
maintain compatibility.
LEAP support is added, hints from Richard Johnson. I've verified this
locally with PC350v42510.img firmware. More bug fixing from Marco to
fix long passwords.
Change DELAYs in flash part of driver to FLASH_DELAY which uses tsleep
so it doesn't look like your system died during a flash update.
Install header files in /usr/include/dev/an
Cleanup some ifmedia bugs add "Home" key mode to ifmedia and ancontrol.
This way you can manage 2 keys a little easier. Map the home mode into
key 5. Enhance ifconfig to dump the various configured SSIDs. I use
a bunch of different ones and roam between them. Use the syntax similar
to the WEP keys to deal with setting difference SSIDs.
Bump up up the Card capabilities RID since they added 2 bytes to it
in the latest firmware. Thankfully we changed it from a terminal
failure so the card still worked but the driver whined.
Some cleanup patches from Marco Molteni.
Submitted by: Richard Johnson <raj@cisco.com>
Marco Molteni <molter@tin.it>
and myself
Various checks: David Wolfskill <david@catwhisker.org>
Reviewed by: Brooks Davis <brooks@freebsd.org>
Warner Losh <imp@freebsd.org>
Approved by: Brooks Davis <brooks@freebsd.org>
Warner Losh <imp@freebsd.org>
Obtained from: Linux emulation API's from Aironet driver.
socreate(), rather than getting it implicitly from the thread
argument.
o Make NFS cache the credential provided at mount-time, and use
the cached credential (nfsmount->nm_cred) when making calls to
socreate() on initially connecting, or reconnecting the socket.
This fixes bugs involving NFS over TCP and ipfw uid/gid rules, as well
as bugs involving NFS and mandatory access control implementations.
Reviewed by: freebsd-arch
In order of importance:
* Make ugen use updated frlengths.
* More tests for NULL pipes.
* Generate better error codes on bulk write.
* Error messages in general.
(1) Don't attempt aquire the non-recursive lock sio_lock recursively.
Doing so caused unbounded recursion in some setups. E.g., if DDB,
BREAK_TO_DEBUGGER and WITNESS are configured; if the debugger is
entered using a break, then WITNESS will actually detect the invalid
recursion and will add to it attempting to print a message about it.
(2) Don't use sio_lock before it has been initialized. The old check
(sio_inited != 0) didn't work when sio_inited was boolean because
sio_inited was set too early, and became just wrong when sio_inited
was changed to a tri-state variable in rev.1.348.
Reported and fixed in another way by: fenner (1)
see people trip over it. Do not set the FIFO trigger to just before it
would otherwise overflow. Give it a little more slop so characters aren't
lost if the interrupt is delayed by other system activities.
MFC maybe: 7 days
- Temporary fix a bug of Intel ACPI CA core code.
- Add OS layer ACPI mutex support. This can be disabled by
specifying option ACPI_NO_SEMAPHORES.
- Add ACPI threading support. Now that we have a dedicate taskqueue for
ACPI tasks and more ACPI task threads can be created by specifying option
ACPI_MAX_THREADS.
- Change acpi_EvaluateIntoBuffer() behavior slightly to reuse given
caller's buffer unless AE_BUFFER_OVERFLOW occurs. Also CM battery's
evaluations were changed to use acpi_EvaluateIntoBuffer().
- Add new utility function acpi_ConvertBufferToInteger().
- Add simple locking for CM battery and temperature updating.
- Fix a minor problem on EC locking.
- Make the thermal zone polling rate to be changeable.
- Change minor things on AcpiOsSignal(); in ACPI_SIGNAL_FATAL case,
entering Debugger is easier to investigate the problem rather than panic.
to Phil Kernick:
"The problem is that in full duplex mode, the Conexant chip always reports a
carrier lost error, even when the frame is successfully sent. So, if we
have a Conexant chip, then ignore carrier lost when in full duplex
mode."
Since the Xircom chips seem to have the same issue and since we already
have a workaround for this, just expand the workaround test to also
check for DC_IS_CONEXANT().
to a label is inside an #ifdef block, then the label should *also* be
inside an #ifdef block. Hide the "done:" label which is only used if
DEVICE_POLLING is enabled under #ifdef DEVICE_POLLING.
must be cleared to prevent machine hanging (presently aflicts -current
and -stable).
Problem reported by Bruce Montague <brucem@cse.iitkgp.ernet.in>
PR: kern/29769 (probably)
otherwise breaks on the Alpha arch. I think this is wrong since i'd
actually like to probe for a PC architecture, not for a particular CPU
type. Anyway, now it's again the way it used to be.
sense, and mode select into their 10 byte equivalents. Eventually the
da(4) driver will become more intelligent about this, or at least allow
umass(4) to pass quirks in directly. However, this is a functional
workaround until a better fix is implemented.
- Use the 6 to 10 conversion function to allow the ATAPI and UFI command
sets to emulate 6 byte commands with 10 byte commands.
- Use the ATAPI command set rather than UFI for the ScanLogic SL11R-IDE
as it supports the SYNCH_CACHE command.
- Enable ATAPI command set support.
- Pass READ/WRITE_12 commands through for UFI support as the UFI spec
says they should be supported.
- Update a comment in the UFI translation function since we handle
MODE_SELECT.
- The MD functions critical_enter/exit are renamed to start with a cpu_
prefix.
- MI wrapper functions critical_enter/exit maintain a per-thread nesting
count and a per-thread critical section saved state set when entering
a critical section while at nesting level 0 and restored when exiting
to nesting level 0. This moves the saved state out of spin mutexes so
that interlocking spin mutexes works properly.
- Most low-level MD code that used critical_enter/exit now use
cpu_critical_enter/exit. MI code such as device drivers and spin
mutexes use the MI wrappers. Note that since the MI wrappers store
the state in the current thread, they do not have any return values or
arguments.
- mtx_intr_enable() is replaced with a constant CRITICAL_FORK which is
assigned to curthread->td_savecrit during fork_exit().
Tested on: i386, alpha
the link rate - some ich motherboards overclock ac97 out of the box.
Will hopefully replace this with a callibration loop in time for 4.5R
freeze.
Problem reported by Luigi Rizzo and fix derived from his code (put
diff in ich.c rather than ac97.c).
MFC after: 3 days
. The main device node now supports automatic density selection for
commonly used media densities. So you can stuff your 1.44 MB and
720 KB media into your drive and just access /dev/fd0, no questions
asked. It's all that easy, isn't it? :)
. Device density handling has been completely overhauled. The old way
of hardwired kernel density knowledge is no longer there. Instead,
the kernel now implements 16 subdevices per drive. The first
subdevice uses automatic density selection, while the remaining 15
devices are freely programmable. They can be assigned an arbitrary
name of the form /dev/fd[:digit]+.[:digit:]{1,4}, where the second
number is meant to either implement device names that are mnemonic
for their raw capacity (as it used to be), or they can alternatively
be created as "anonymous" devices like fd0.1 through fd0.15,
depending on the taste of the administrator. After creating a
subdevice, it is initialized to the maximal native density of the
respective drive type, so it needs to be customized for other
densities by using fdcontrol(8). Pseudo-partition devices (fd0a
through fd0h) are still supported as symlinks.
. The old hack to use flags 0x1 to always assume drive 0 were there is
no longer supported; this is now supposed to be done by wiring the
devices down from the loader via device flags. On IA32
architectures, the first two drives are looked up in the CMOS
configuration records though. On PCMCIA (i. e., the Y-E Data
controller of the Toshiba Libretto), a single drive is always
assumed.
. Other specialities like disabling the FIFO and not probing the drive
at boot-time are selected by per-controller or per-drive flags, too.
. Unit attentions (media has been changed) are supposed to be detected
now; density autoselection only occurs after a unit attention. (Can
be turned off by a per-drive flag, this will cause each Fdopen() to
perform the autoselection.)
. FM floppies can be handled now (on controllers that actually support
it -- not all do these days).
. Fdopen() can be told to avoid density selection by setting
O_NONBLOCK; this leaves the descriptor in a half-opened state where
only a few ioctls are accepted. This is necessary to run fdformat
on a device that uses automatic density selection (since you cannot
autoselect on an unformatted medium, obviously).
. Just differentiate between a plain old NE765 and the enhanced chips,
but don't try more; the existing code was wrong and only misdetected
the chips anyway.
BUGS and TODOs:
. All documentation update still needs to be done.
. Formatting not-so-standard format yields unpredictable results; i
have yet to figure out why this happens. "Standard" formats like
720 and 1440 KB do work, however.
. rc scripts are needed to setup device nodes with nonstandard
densities (like the old /dev/fdN.MMM we used to have).
. Obtaining device flags from the kernel environment doesn't work yet,
thus currently only drives that are present in (IA32) CMOS are
really detected. Someone who knows the odds and ends about device
flags is needed here, i can't figure out what i'm doing wrong.
. 2.88 MB still needs to be done.
Non-SMP, i386-only, no polling in the idle loop at the moment.
To use this code you must compile a kernel with
options DEVICE_POLLING
and at runtime enable polling with
sysctl kern.polling.enable=1
The percentage of CPU reserved to userland can be set with
sysctl kern.polling.user_frac=NN (default is 50)
while the remainder is used by polling device drivers and netisr's.
These are the only two variables that you should need to touch. There
are a few more parameters in kern.polling but the default values
are adequate for all purposes. See the code in kern_poll.c for
more details on them.
Polling in the idle loop will be implemented shortly by introducing
a kernel thread which does the job. Until then, the amount of CPU
dedicated to polling will never exceed (100-user_frac).
The equivalent (actually, better) code for -stable is at
http://info.iet.unipi.it/~luigi/polling/
and also supports polling in the idle loop.
NOTE to Alpha developers:
There is really nothing in this code that is i386-specific.
If you move the 2 lines supporting the new option from
sys/conf/{files,options}.i386 to sys/conf/{files,options} I am
pretty sure that this should work on the Alpha as well, just that
I do not have a suitable test box to try it. If someone feels like
trying it, I would appreciate it.
NOTE to other developers:
sure some things could be done better, and as always I am open to
constructive criticism, which a few of you have already given and
I greatly appreciated.
However, before proposing radical architectural changes, please
take some time to possibly try out this code, or at the very least
read the comments in kern_poll.c, especially re. the reason why I
am using a soft netisr and cannot (I believe) replace it with a
simple timeout.
Quick description of files touched by this commit:
sys/conf/files.i386
new file kern/kern_poll.c
sys/conf/options.i386
new option
sys/i386/i386/trap.c
poll in trap (disabled by default)
sys/kern/kern_clock.c
initialization and hardclock hooks.
sys/kern/kern_intr.c
minor swi_net changes
sys/kern/kern_poll.c
the bulk of the code.
sys/net/if.h
new flag
sys/net/if_var.h
declaration for functions used in device drivers.
sys/net/netisr.h
NETISR_POLL
sys/dev/fxp/if_fxp.c
sys/dev/fxp/if_fxpvar.h
sys/pci/if_dc.c
sys/pci/if_dcreg.h
sys/pci/if_sis.c
sys/pci/if_sisreg.h
device driver modifications
a GetAllNext response. Otherwise, we won't unswizzle
it correctly. This was found on linux/PPC.
This mandated creating another inline: isp_get_gan_response.
Introduce an additional device flag for those NICs which require the
transmit buffers to be aligned to 32-bit boundaries.
(the equivalen fix for STABLE is slightly simpler because there are
no supported chips which require this alignment there.)
the response queue. Instead of the ad hoc ISP_SWIZZLE_REQUEST, we now have
a complete set of inline functions in isp_inline.h. Each platform is
responsible for providing just one of a set of ISP_IOX_{GET,PUT}{8,16,32}
macros.
The reason this needs to be done is that we need to have a single set of
functions that will work correctly on multiple architectures for both little
and big endian machines. It also needs to work correctly in the case that
we have the request or response queues in memory that has to be treated
specially (e.g., have ddi_dma_sync called on it for Solaris after we update
it or before we read from it). It also has to handle the SBus cards (for
platforms that have them) which, while on a Big Endian machine, do *not*
require *most* of the request/response queue entry fields to be swizzled
or unswizzled.
One thing that falls out of this is that we no longer build requests in the
request queue itself. Instead, we build the request locally (e.g., on the
stack) and then as part of the swizzling operation, copy it to the request
queue entry we've allocated. I thought long and hard about whether this was
too expensive a change to make as it in a lot of cases requires an extra
copy. On balance, the flexbility is worth it. With any luck, the entry that
we build locally stays in a processor writeback cache (after all, it's only
64 bytes) so that the cost of actually flushing it to the memory area that is
the shared queue with the PCI device is not all that expensive. We may examine
this again and try to get clever in the future to try and avoid copies.
Another change that falls out of this is that MEMORYBARRIER should be taken
a lot more seriously. The macro ISP_ADD_REQUEST does a MEMORYBARRIER on the
entry being added. But there had been many other places this had been missing.
It's now very important that it be done.
Additional changes:
Fix a longstanding buglet of sorts. When we get an entry via isp_getrqentry,
the iptr value that gets returned is the value we intend to eventually plug
into the ISP registers as the entry *one past* the last one we've written-
*not* the current entry we're updating. All along we've been calling sync
functions on the wrong index value. Argh. The 'fix' here is to rename all
'iptr' variables as 'nxti' to remember that this is the 'next' pointer-
not the current pointer.
Devote a single bit to mboxbsy- and set aside bits for output mbox registers
that we need to pick up- we can have at least one command which does not
have any defined output registers (MBOX_EXECUTE_FIRMWARE).
MFC after: 2 weeks
pcm0: ac97 codec failed to reset extended mode (0, got 80)
This was due to not masking off the correct extended function bits
in the read value from the extended status reg.
MFC after: 2 days
some Toshiba and Thinkpad laptops.
Wakeup event is generated by power button or sleep button on some
laptops but this also generates SCI interrupt, and shutdown the system
as result. So this is introduced so that acpi driver ignore given
requests for certain period.
the UFI command set. Even with this patch, it's incredibly slow on my
laptop, but at least now it works.
Note that the drive is reported to CAM with the vendor and device IDs from
the device itself, forcing the user to patch the da(4) quirk table
manually.
controllers. There still seems to be some issues with the DRI copying code
for some adapters, at least it doesn't hang the system now. Input would be
appreciated.
PR: 32301
Obtained from: Eric Anhlot <eanholt@gladstone.uoregon.edu>, Joe <joeo@nks.net>
The reason we are required to commit to -current first is so that later
MFC's do not risk the loss of existing bug fixes. Even if this was not
strictly required in -current, it should still be fixed there too.
1. Changed incorrect conditional in fxhw.c which would never
evaluate to true. Thanks to John Polstra for pointing that out.
2. Write to PCI config space by default, enabling memory access and
bus master enable.
Submitted by:Prafulla Deuskar
MFC after:3 days
Similar code was submitted in PR 5559 by Takeshi OHASHI-san, but the
PC Card system has changed much since then, so this is a fresh
implementation.
PR: i386/5559
Submitted by: Takeshi OHASHI
prism2 flag in pccard.conf, but I'm leaving it place for the moment in
case the small sample of PrismII cards that I've tried is not
representative.
MFC After: 30 days
Obtained from: NetBSD
released management apps.
1. Implement poll(). This will check for queued aif's so that a
subsequent ioctl call to retrieve the next aif will not block.
2. Don't catch signals when sleeping on a fib sent from userland. This
causes a race and panic due to the pthread context switcher waking
up the tsleep at inopportune times.
3. Fix some whitespace nits.
MFC after: 3 days
- set sc->acpi_s4bios to 1 by default for hibernation until
OS-initiated S4 transition is implemented.
- change the behavior of acpi_sleep_state_sysctl() if new value is
the same as old one, do nothing instead of EINVAL.
mbuf allocation fails, and fix (i hope) a couple of style bugs.
I believe these printf() are extremely dangerous because now they can
occur on every incoming packet and are not rate limited. They were
meant to warn the sysadmin about lack of resources, but now they
can become a nice way to panic your system under load.
Other drivers (e.g. the fxp driver) have nothing like this.
There is a pending discussion on putting this kind of warnings
elsewhere, and I hope we can fix this soon.
underlying unaligned bcopy) on incoming packets that are already
available (albeit unaligned) in a buffer.
The performance improvement varies, depending on CPU and memory
speed, but can be quite large especially on slow CPUs. I have seen
over 50% increase on forwarding speed on the sis driver for the
486/133 (embedded systems), which does exactly the same thing.
The behaviour is controlled by a sysctl variable, hw.dc_quick which
defaults to 1. Set it to 0 to restore the old behaviour.
After running a few experiments (in userland, though) I am convinced
that doing the m_devget() is detrimental to performance in almost
all cases.
Even if your CPU has degraded performance with misaligned data,
the bcopy() in the driver has the same overhead due to misaligment
as the one that you save in the uiomove(), plus you do one extra
copy and pollute the cache.
But more often than not, you do not even have to touch the payload,
e.g. when you are forwarding packets, and even in the often-cited
case of NFS, you often end up passing a pointer to the payload to
the disk controller.
In any case, you can play with the sysctl variable to toggle between
the two behaviours, and see if it makes a difference.
MFC-after: 3 days
allows us to move the sio softc data structure back into sio.c and
reduce the complexity of the non sio.c sio files.
Submitted by: bde
# I didn't fix the locking issues that bruce also submitted.
loader parameter. This allows us to more easily boot on big memory
configuration machines. hw.pccbb.start_mem. Reflect this in a sysctl
so we can read it from userland.
# Note: we need a TUNABLE_ULONG to do this right. I'll add that to
# kernel.h soon.
request to one that's supported by the bridge. I'm not 100% sure this
is correct, but it makes it easier for the cardbus bridge to allocate
its memory.
Similar code is needed for the I/O range. Also, I'm not sure if I
should be doing this based on memory or pmemory (but likely should do
it based on some flag that tells us to prefetch or not).
Talked about a long time ago with: msmith
NEWCARD. Other patches may be reqiured to sio to prevent a hang on
eject. Also add commented out entries for sio_pccard.c in files.pc98
to match other architectures.
Submitted by: yamamoto shigeru-san
changing. Also change it from 0x44000000 to 0x84000000 for large memory
machines.
# the PCI bus code should do this for us. This is a bandaide, not a
# solution.
click) do not include newline into the buffer. This is exacly how
things worked before my recent changes to the cut'n'paste code and
how they work in 4-STABLE.
card is ejected while we're in this routine.
yamamoto-san's original patch had a small race window for AX88190
chips, which I corrected by limiting the number of iterations we'd try
to reset the bits to be about 15ms rather than forever. This seems to
work for me, but I don't have a large collections of cards based on
this chipset.
Submitted by: YAMAMOTO Shigeru
snooped on. This causes all kinds of Bad Things(tm) to happen since
closing one session will clobber state that's needed for the other
one. This could theoretically be supported if the code was careful,
but until somebody implements that, preventing this will stop people
from unknowingly shooting themselves in the foot.
device cloned, and assign all further devices to depend on it. This
allows us to call dev_depends() on it at module unload time to get rid
of /dev/snp* (in the devfs case, anyway). For this to work, we must
not destroy the device at close time. [Idea stolen from if_tun.]
The above has the following sideaffects: (a) The snp device used by
watch(8) will remain after watch(8) exits. This is probably how it
should have been all along, and how it was before devfs came along.
(b) Module unload doesn't panic if there are any /dev/snp* devices
which haven't been used (and thus previously destroyed). Thus, we can
reenable the unload functionality disabled in rev. 1.65.
PR: 32012
MFC after:3 days
- Add memory barrier definition for sparc64.
Patch sent by David E. O'Brien, approved by maintainer.
- Fix an endianization error of a bus physical address used from SCRIPTS
that made the driver fail on big endian machines as sparc64.
signature, but otherwise behaves just like a normal USB mass-storage
device. Add a new quirk to cover this case, and enable it for C-1
cameras. The quirk enables translation from the C-1 signature to
the normal CSWSIGNATURE value.
Reviewed by: n_hibma
Actually this porting supports Pegasus II chip so I guess some other
devices supported by NetBSD also work. But the devices list are not
included because I cannot confirm if they work.
Obtained from: NetBSD
MFC after: 3 weeks
2. Add OF_getprop_alloc(), a helper function that will malloc() a sufficient
amount of memory and then retrieve a property value into it.
Approved by: benno
Obtained from: NetBSD (1)
disabled unless verbose flag is set. Also fix some messages in terms
of English.
The critical messages and error messages in probe/attach routine are
unchanged by this commit.
Now you can say;
# sysctl hw.acpi.lid_switch_state=NONE
instead of specifying unsupported _Sx object in the system.
Actually, S4B is going to disappear in ACPICA and we already have
hw.acpi.s4bios to distinguish BIOS hibernation or OS hibernation.
pccard layer and rename them PCMCIA_CARD and PCMCIA_CARD2 respectively
(note, this is being done with an eye towards NetBSD integreation so
it is easier to keep lists of cards between us and them in sync).
Use this in the an and wi drivers.
trying something new with the macros here and will likely try to get
them adopted by NetBSD as well as moving them to other drivers. They
make the list more compact and easier to read, the price of rigid to a
schema for generating them (of course there are those that would argue
this isn't bad).
Obtained from: NetBSD's if_wi_pcmcia.c 1.9
off chip that was on one prototype board. However, this appears to be
a design that many chipsets are compatible with its PPEC register set
(eg the Omega 82c094). Through the kindness of the Red Hat developer
David Woodhouse, I now have this datasheet.
I may take the advise of one of the bsd-nomads (whose name
unfortunately escapes me at the moment) and split out all these 16-bit
I/O mapped PCI devices into a separate driver...
that it has one BAR that's mapped to 0x3e0 and is I/O only. It does
not conform to the Yenta spec, like other PCI PCMICA bridges do (eg
the TI 1031, which is mostly a 1131 w/o 32bit card support). It
appears that this chip may also need to not route PCI interrupts
as well.
This chip is used in the NEC Versa 2430CD (and it appears that
sometimes it works, while other times it doesn't) and others in the
2400 series. While the NEC website claims Cardbus support, I can't figure
out how that is possible.
Submitted by: Ben Timby <ben@webexc.com>
- Add S4BIOS sleep implementation. This will works well if MIB
hw.acpi.s4bios is set (and of course BIOS supports it and hibernation
is enabled correctly).
- Add DSDT overriding support which is submitted by takawata originally.
If loader tunable acpi_dsdt_load="YES" and DSDT file is set to
acpi_dsdt_name (default DSDT file name is /boot/acpi_dsdt.aml),
ACPI CA core loads DSDT from given file rather than BIOS memory block.
DSDT file can be generated by iasl in ports/devel/acpicatools/.
- Add new files so that we can add our proposed additional code to Intel
ACPI CA into these files temporary. They will be removed when
similar code is added into ACPI CA officially.
