o Make DXS3 the primary playback channel. It may be the only
universally supported channel with the assorted revisions of this
chipset.
o Add sysctl and handler for enabling s/pdif output from DXS3.
Retire the "d_dump_t" and use the "dumper_t" type instead.
Dumper_t takes a void * as first arg which is more general than the
dev_t taken by d_dump_t. (Remember: we could have net-dumpers if
somebody wrote us one!)
Define the convention for GEOM controlled disk devices to be that the
first argument to the dumper function is the struct disk pointer.
Change device drivers accordingly.
Change the argument to disk_destroy() to be the same struct disk * as
disk_create() takes.
This enables drivers to ignore the (now) bogus dev_t which disk_create()
returns.
a number of related problems along the way.
- Automatically detect CDROM drives that can't handle 6 byte mode
sense and mode select, and adjust our command size accordingly.
We have to handle this in the cd(4) driver (where the buffers are
allocated), since the parameter list length is different for the
6 and 10 byte mode sense commands.
- Remove MODE_SENSE and MODE_SELECT translation removed in ATAPICAM
and in the umass(4) driver, since there's no way for that to work
properly.
- Add a quirk entry for CDROM drives that just hang when they get a 6
byte mode sense or mode select. The reason for the quirk must be
documented in a PR, and all quirks must be approved by
ken@FreeBSD.org. This is to make sure that we fully understand why
each quirk is needed. Once the CAM_NEW_TRAN_CODE is finished, we
should be able to remove any such quirks, since we'll know what
protocol the drive speaks (SCSI, ATAPI, etc.) and therefore whether
we should use 6 or 10 byte mode sense/select commands.
- Change the way the da(4) handles the no_6_byte sysctl. There is
now a per-drive sysctl to set the minimum command size for that
particular disk. (Since you could have multiple disks with
multiple requirements in one system.)
- Loader tunable support for all the sysctls in the da(4) and cd(4)
drivers.
- Add a CDIOCCLOSE ioctl for cd(4) (bde pointed this out a long
time ago).
- Add a media validation routine (cdcheckmedia()) to the cd(4)
driver, to fix some problems bde pointed out a long time ago. We
now allow open() to succeed no matter what, but if we don't detect
valid media, the user can only issue CDIOCCLOSE or CDIOCEJECT
ioctls.
- The media validation routine also reads the table of contents off
the drive. We use the table of contents to implement the
CDIOCPLAYTRACKS ioctl using the PLAY AUDIO MSF command. The
PLAY AUDIO TRACK INDEX command that we previously used was
deprecated after SCSI-2. It works in every SCSI CDROM I've tried,
but doesn't seem to work on ATAPI CDROM drives. We still use the
play audio track index command if we don't have a valid TOC, but
I suppose it'll fail anyway in that case.
- Add _len() versions of scsi_mode_sense() and scsi_mode_select() so
that we can specify the minimum command length.
- Fix a couple of formatting problems in the sense printing code.
MFC after: 4 weeks
Some drives seem to be confused by simultaneous probes.
Tested by: marcel
As a side effect, logical units whose lun is greater than 0 might not be
probed correctly if the lun of 0 doesn't exist in the target because
CAM doesn't scan such luns.
I have a SCSI-FireWire bridge which maps SCSI-ID to LUN and it is an
example of such targets.
dev_t to the method functions.
The dev_t can still be found at struct consdev *->cn_dev.
Add a void *cn_arg element to struct consdev which the drivers can use
for retrieving their softc.
This moves all chipset specific code to a new file 'ata-chipset.c'.
Extensive use of tables and pointers to avoid having the same switch
on chipset type in several places, and to allow substituting various
functions for different HW arch needs.
Added PIO mode setup and all DMA modes.
Support for all known SiS chipsets. Thanks to Christoph Kukulies for
sponsoring a nice ASUS P4S8X SiS648 based board for this work!
Tested on: i386, PC98, alpha and sparc64
support for Tekram DC395U2W cards.
Add a fix submitted by joerg@ to correctly report some errors to CAM.
Use bus_dma instead of the remaining vtophys().
field for holding driver-dependant data. Instead of putting the pointer
to the driver command struct in there, take advantage of these structs
being a (virtually) contiguous array and just put the array index in the
field.
that a command completion happened, all further processing is deferred to
a taskqueue. The taskqueue itself runs implicetely under Giant, but we
already used a taskqueue for the biodone() processing, so this at least
saves the contesting of Giant in the interrupt handler.
retain symetry with aac_alloc_commans(). Since aac_alloc_commands()
allocates fib maps and places them onto the fib lists, aac_free_commands()
should reverse those operations.
o Combine two ifs with the same body with an ||.
o Switch from uintptr_t to uint32_t for fib map load operations.
The target is a uint32_t so using this type for the map load call
avoids an extra cast. uintptr_t should only be used when you need
an "int sized the same as the machine's poitner size" which is not
the case here.
o Removed the commented out M_WAITOK flag in the allocation in
aac_alloc_commands(). The kernel will only block in the allocator
if it can grow the size of the kernel. This usually results in a
page-out which could involve this aac device. Thus, sleeping here
could deadlock the machine. Assuming this operation is occurring outside
of attach time, we have enough fibs to operate anyway, so waiting for
fibs to free up is okay if not optimal.
o In aac_alloc_commands(), if we cannot dmamem_alloc additional fib
space, free the fib map.
o In aac_alloc_commands(), if we cannot create per-command dmamaps, don't
lose track of the fib map that is mapping all of the commands that we
have already released into the free pool. Instead, just cut out of
the loop and modify aac_free_commands to not attempt to free maps that
have not been allocated.
o Don't use a magic number when pre-allocating fibs.
o Use PAGE_SIZE to allocate in page sized chunks instead of an
architecture specific constant.
Submitted by: gibbs
Minor CIS resource allocation code cleanup
Remove some fairly useless debug writes.
This finishes the work to move as much cardbus code as possible into
pci. We wind up removing 800-odd lines from cardbus.c: we go from
1285 to 400 lines.
Reviewed by: mdodd
- Fix memory leak in detaching.
- Initialize fc->status to other than FWBUSREST.
* fwohci.c
- Ignore BUS reset events while BUS reset phase. We can't clear that flag
during bus reset phase.
is encoded in the PCI BAR. The latter is more reliable.
This allows the sio/modem function of the Xircom RealPort ethernet+modem
card to work. Note that there still seem to be issues with sio_pci not
releasing resources on detach.
pci busses implement this.
Also minor comment smithing in cardbus. Fix copyright to this year
with my name on it since I've been doing a lot to this file.
Reviewed by: jhb
- Don't initiate bus reset even if probe failed for some nodes to prevent
infinite bus reset loop.
Problem Reported by: Pierre Beyssac <pb@fasterix.frmug.org>
- Protect timeout routine with splfw() for 4-stable.
* sbp.c
- Make sure to release devq when start request.
Wearing said pointy hat, correct the oversight and hope nobody
notices.
# this should make xircom modems happier to detach once other bugs with
# the cardbus layer are fixed.
Noticed by: scottl
Conical Hat to: imp
o Use the common pci_* routines in preference to the copied and hacked
routines from an ancient pci.c.
This saves 509 lines in cardbus.c. More savings to follow when I
convert the resource code over. In the past when I've done this the
resource code conversion breaks cardbus in subtle ways so I'm doing a
1/2 way checkpoint this time. cardbus still works for me the same as
it did before.
It also looks like cardbus devices now show up as pci bus devices to
pciconf -l, but maybe that was happening before.
Inspired by a patch from Justin Gibbs many moons ago. When he
finishes his kobj multiple inheritance work, we can transition the
finished version of this work to that fairly easily.
