could get an interrupt after we free the ifp, and the interrupt
handler depended on the ifp being still alive, this could, in theory,
cause a crash. Eliminate this possibility by moving the if_free to
after the bus_teardown_intr() call.
possible method to prevent panicing in interrupt handler
after re_shutdown(), sometimes seen on SMP systems.
This would work here only because re_detach() clears
IFF_UP (to prevent another race) and it was demonstrated
that it's not enough to call vr_detach() in vr_shutdown()
to prevent a panic.
- Fixed if_free() logic screw-up that can either result
in freeing a NULL pointer or leaking "struct ifnet".
- Move if_free() after re_stop(); the latter accesses
"struct ifnet". This bug was masked by a previous bug.
- Restore the fix for a panic on detach caused by racing
with BPF detach code by Bill by moving ether_ifdetach()
after re_stop() and resetting IFF_UP; this got screwed
up in revs. 1.30 and 1.36.
interrupt comes in later on, which can happen in some uncommon cases.
Another possible fix is to call re_detach() instead of re_stop(), like
ve(4) does, but I am not sure if the latter is really RTTD, so that stick
with this one-liner for now.
PR: kern/80005
Approved by: silence on -arch, no reply from selected network gurus
IFF_DRV_RUNNING, as well as the move from ifnet.if_flags to
ifnet.if_drv_flags. Device drivers are now responsible for
synchronizing access to these flags, as they are in if_drv_flags. This
helps prevent races between the network stack and device driver in
maintaining the interface flags field.
Many __FreeBSD__ and __FreeBSD_version checks maintained and continued;
some less so.
Reviewed by: pjd, bz
MFC after: 7 days
over iteration of their multicast address lists when synchronizing the
hardware address filter with the network stack-maintained list.
Problem reported by: Ed Maste (emaste at phaedrus dot sandvine dot ca>
MFC after: 1 week
struct ifnet or the layer 2 common structure it was embedded in have
been replaced with a struct ifnet pointer to be filled by a call to the
new function, if_alloc(). The layer 2 common structure is also allocated
via if_alloc() based on the interface type. It is hung off the new
struct ifnet member, if_l2com.
This change removes the size of these structures from the kernel ABI and
will allow us to better manage them as interfaces come and go.
Other changes of note:
- Struct arpcom is no longer referenced in normal interface code.
Instead the Ethernet address is accessed via the IFP2ENADDR() macro.
To enforce this ac_enaddr has been renamed to _ac_enaddr.
- The second argument to ether_ifattach is now always the mac address
from driver private storage rather than sometimes being ac_enaddr.
Reviewed by: sobomax, sam
to 7422 since it appears that the 8169S can't transmit anything larger..
The 8169S can receive full jumbo frames, but we don't have an mru to let
the upper layers know this...
add fixup so that this driver should work on alignment constrained platforms
(!i386 && !amd64)
MFC after: 5 days
This essentially merges revs 1.143-1.1445 of sys/pci/if_rl.c.
This now marks the interrupt MPSAFE along with making the mutex non-recursive.
Looked over by: bms
this problem put these lines back in. While they should be
unnecessary, they appear to be sometimes necessary.
Reviewed in concept: dfr
Approved by: re (scottl@)
the packets are immediately returned for sending (e.g. when bridging
or packet forwarding). There are more efficient ways to do this
but for now use the least intrusive approach.
Reviewed by: imp, rwatson
multicast hash are written. There are still two distinct algorithms used,
and there actually isn't any reason each driver should have its own copy
of this function as they could all share one copy of it (if it grew an
additional argument).
to the pci attachment. Cardbus is a derived class of pci so all pci
drivers are automatically available for matching against cardbus devices.
Reviewed by: imp
if_xname, if_dname, and if_dunit. if_xname is the name of the interface
and if_dname/unit are the driver name and instance.
This change paves the way for interface renaming and enhanced pseudo
device creation and configuration symantics.
Approved By: re (in principle)
Reviewed By: njl, imp
Tested On: i386, amd64, sparc64
Obtained From: NetBSD (if_xname)
device to access 64-bit addresses from a 32-bit PCI bus. While the
RealTek manual says you can set this bit and the chip will perform
DAC only if you give it a DMA address with any of the upper 32
bits set, this appears not to be the case. If I turn on the DAC
bit, the chip sets the 'system error' bit in the status register
when I to do a DMA on my Athlon test box with 32-bit PCI bus (VIA
chipset) even though I only have 128MB of physical memory, and thus
can never give the chip a 64-bit address.
Obviously, I can't just set it and forget it, so until I figure
out the right rule for when it's safe/necessary to enable it, keep
it turned off.
IF_HANDOFF() does it for us behind the scenes. Remove the extra call
to re_start() otherwise we try to transmit twice.
In re_encap(), fix the code that guards against consuming too many
descriptors in the TX ring so that it actually works. With the
new 8169S chip, I was able to hit a corner case that drained the
free descriptor count all the way to 0. This is not supposed to
be possible.
we're on a 32-bit/64-bit bus or not. Use this to decide if we should
set the PCI dual-address cycle enable bit in the C+ command register.
(Enabling DAC on a 32-bit bus seems to do bad things.)
Also, initialize the C+ command register early in the re_init() routine.
The documentation says this register should be configured first.
seems to be necessary for the 8139C+ under certain circumstances, and
doesn't appear to hurt the other chips. (In the failure case, the
packet would be sent through the TX DMA ring but not get echoed
back. I suspect this has something to do with the link state changing
unexpectedly.)
autoload and then copying the contends of the station address
registers. For some reason, reading the EEPROM on the 8169S doesn't
work right. This gets around the problem, and allows us to read
the station address correctly on the 8169S.
- Insert a delay after initiating packet transmition in re_diag() to
allow lots of time for the frame to echo back to the host, and wait
for both the 'RX complete' and 'timeout expired' bits in the ISR
register to be set.
- Deal more intelligently with the fact that the frame length
field in the RX descriptor is a different width on the 8139C+
than it is on the 8169/8169S/8110S
- For the 8169, you have to set bit 17 in the TX config register
to enter digital loopback mode, but for the 8139C+, you have to
set both bits 17 and 18. Take this into account so that re_diag()
works properly for both types of chips.
ethernet chips. This driver is pretty simple, however it contains
special DSP initialization code which is needed in order to get
the chip to negotiate a gigE link. (This special initialization
may not be needed in subsequent chip revs.) Also:
- Fix typo in if_rlreg.h (RL_GMEDIASTAT_1000MPS -> RL_GMEDIASTAT_1000MBPS)
- Deal with shared interrupts in re_intr(): if interface isn't up,
return.
- Fix another bug in re_gmii_writereg() (properly apply data field mask)
- Allow PHY driver to read the RL_GMEDIASTAT register via the
re_gmii_readreg() register (this is register needed to determine
real time link/media status).
