The SPDX folks have obsoleted the BSD-2-Clause-FreeBSD identifier. Catch
up to that fact and revert to their recommended match of BSD-2-Clause.
Discussed with: pfg
MFC After: 3 days
Sponsored by: Netflix
Mainly focus on files that use BSD 2-Clause license, however the tool I
was using misidentified many licenses so this was mostly a manual - error
prone - task.
The Software Package Data Exchange (SPDX) group provides a specification
to make it easier for automated tools to detect and summarize well known
opensource licenses. We are gradually adopting the specification, noting
that the tags are considered only advisory and do not, in any way,
superceed or replace the license texts.
No functional change intended.
structures (well, they're treated as opaque).
It's now possible to manage IPv6 interface addresses and routing
table entries and to filter IPV6 traffic whether encapsulated or
not.
IPV6CP support is crude for now, and hasn't been tested against
any other implementations.
RADIUS and IPv6 are independent of eachother for now.
ppp.linkup/ppp.linkdown aren't currently used by IPV6CP
o Understand all protocols(5) in filter rules rather than only a select
few.
o Allow a mask specification for the ``delete'' command. It's now
possible to specifically delete one of two conflicting routes.
o When creating and deleting proxy arp entries, do it for all IPv4
interface addresses rather than doing it just for the ``current''
peer address.
o When iface-alias isn't in effect, don't blow away manually (via ``iface
add'') added interface addresses.
o When listening on a tcp server (diagnostic) socket, bind so that a
tcp46 socket is created -- allowing both IPv4 and IPv6 connections.
o When displaying ICMP traffic, don't display the icmp type twice.
When display traffic, display at least some information about unrecognised
traffic.
o Bump version
Inspired after filtering work by: Makoto MATSUSHITA <matusita@jp.FreeBSD.org>
0.81.1 of the i4b code - namely support of the I4B_VR_REQ
ioctl via the i4brbchX device.
Ppp controls the phone number, but idle timers and
SYNC/RAW decisions are still made by isdnd (in isdnd.rc).
This involves a new datalink state machine phase. The
``wait for carrier'' phase happens after dialing but
before logging in. The whole dial state should really
be abstracted so that each device type can deal with it
in its own way (thinking about PPPoE) - but that'll have
to wait.
The ``set cd'' symantics remain the same for tty devices,
but we now delay until we either get CD or timeout waiting
(at which time we drop the link if we require CD).
For i4b devices we always insist on carrier.
Thanks to hm@ for his help, and especially for pointing out
that I *don't* need to re-implement isdnd (that was a huge
waste of time !) :-]
o Show more information about missing MP fragments in ``show mp''.
o Do away with mbuf_Log(). It was showing mbuf stats twice on
receipt of LCP/CCP/IPCP packets.... ???!!?
o Pre-allocate a bit extra when creating LQR packets to avoid having
to allocate another mbuf in mbuf_Prepend().
the layering.
We now ``stack'' layers as soon as we open the device (when we figure
out what we're dealing with). A static set of `dispatch' routines are
also declared for dealing with incoming packets after they've been
`pulled' up through the stacked layers.
Physical devices are now assigned handlers based on the device type
when they're opened. For the moment there are three device types;
ttys, execs and tcps.
o Increment version number to 2.2
o Make an entry in [uw]tmp for non-tty -direct invocations (after
pap/chap authentication).
o Make throughput counters quad_t's
o Account for the absolute number of mbuf malloc()s and free()s in
``show mem''.
o ``show modem'' becomes ``show physical''.
with more than one read(). When we detect one, don't
forget to pass it to async_Input() and drop our
terminal back into command mode.
Don't output an extraneous \r if we're passed \r\n
to prompt_vprintf in raw mode.
each time rather than making up a new one.
Increase the authname/authkey max sizes to 100 characters.
Allow ``authkey'' specifications beginning with ``!''.
When a challenge is received, the text following the
``!'' is executed as a program (expanding stuff in the same
way that ``sh'' and ``!bg'' do). The program is passed the
peer name, peer challenge and local ``authname'' on standard
input and is expected to output the name/key combination that
should be used to build the CHAP response.
This provides support for Secure ID cards (guess what I was
given at work recently!) using CHAP.
Examples will follow.
input routines and take advantage of the new init/continue
interface in libradius. This allows a timely response on
other links in an MP setup while RADIUS requests are in
progress as well as the ability to handle other data from
the peer in parallel. It should also make the future addition
of PAM support trivial.
While I'm in there, validate pap & chap header IDs if
``idcheck'' is enabled (the default) for other FSM packet
types.
NOTE: This involved integrating the generation of chap
challenges and the validation of chap responses
(and commenting what's going on in those routines).
I currently have no way of testing ppps ability
to respond to M$Chap CHALLENGEs correctly, so if
someone could do the honours, it'd be much
appreciated (it *looks* ok!).
Sponsored by: Internet Business Solutions Ltd., Switzerland
details. Compiling with -DNORADIUS (the default for `release')
removes support.
TODO: The functionality in libradius::rad_send_request() needs
to be supplied as a set of routines so that ppp doesn't
have to wait indefinitely for the radius server(s). Instead,
we need to get a descriptor back, select() on the descriptor,
and ask libradius to service it when necessary.
For now, ppp blocks SIGALRM while in rad_send_request(), so
it misses PAP/CHAP retries & timeouts if they occur.
Only PAP is functional. When CHAP is attempted, libradius
complains that no User-Password has been specified... rfc2138
says that it *mustn't* be used for CHAP :-(
Sponsored by: Internet Business Solutions Ltd., Switzerland
(see the new ``set callback'' and ``set cbcp'' commands)
o Add a ``cbcp'' log level and mbuf type.
o Don't dump core when \T is given in ``set login'' or
``set hangup''.
o Allow ``*'' and blanks as placeholders in ppp.secret and
allow a fifth field for specifying auth/cbcp dialback
parameters.
o Remove a few extraneous #includes
o Define the default number of REQs (restart counter) in defs.h
rather than hardcoding ``5'' all over the place.
o Fix a few man page inconsistencies.
o Allow ``set ....'' when we have multiple links but aren't in
multilink mode.
o Do a TLS when we receive a ``Open'' event in ``Closed'' state,
despite the rfc state transition table. This is clearly an
error in the RFC as TLS cannot have yet been called (without
TLF) in the ``Closed'' state.
I've posted a message to comp.protocols.ppp for confirmation.
into the ST_STOPPED state.
o Allow an optional ccp|lcp argument to `down'. The default is
still lcp (as before). You can now call down with no context
in multilink mode, in which case it'll down the multilink ccp
or the entire bundle (*very* rude).
o Allow an optional `!' after `close ccp' (close ccp!) to tell
ccp to stay in the CLOSED state after the terminate ACK. The
default is now to re-enter STOPPED so that the peer can bring
the layer back up if desired.
o Always handle proto-compressed packets, even if we've agreed
(in LCP) that the peer will not send us 1 byte protocols.
If the peer violates the LCP agreement, log it to the HDLC
log.
o Fix some comments.
LQM and HDLC timer diagnostics come out with the correct name.
o Don't send an LQR immediately upon reviving a datalink. Leave
it 'till the next timeout.
o Add the link name to some more LQR diagnostics.
o Break out of the main loop when a descriptor exception is seen
in select().
o Remove the evil nointr_[u]sleep() functions. Timers should be
(and are) used instead.
o Treat a read() of 0 bytes as an error that's fatal to the link
on which the read() is done. We should never read() 0 after
select() says there's something there - not unless the link
has been closed by the other side.
o Write the data seen before a HDLC header to the terminal in
`term' mode, *not* back to the modem :-/
o Initialise our transmitted file descriptor before starting any
timers.
o Only send data links that have *no* pending output data. This
means that our final ACK will be written rather than being
nuked with the datalink transmission.
according to SHORTSEQ negotiation.
o Don't forget to attach incoming fragments with a
number greater than everything else in the queue
(rather than leaking memory).
o Output the link name with the ``other'' hdlc
diagnostic message.
o Correct a VJ diagnostic (`COMPPROTO', not `proto').
o Create struct mpserver as part of struct mp.
mpserver creates a unix-domain socket based on the
peers auth name and endpoint discriminator. If it
already exists, ppp will ``pass the link'' over to
the owner of the socket, joining it into the bundle
of another ppp invocation, otherwise ppp waits for
other invocations to pass it links through this
socket.
The final piece of code will be the code that flattens
our datalink info and passes it down this channel
(not yet implemented).
we've determined if we're going to join another ppp invocation.
o Make ``show link'' show all link details, and ``show links''
just give a list of links and their current status.
o Show our current label in ``show bundle''.
o Allow link cloning and removal as soon as our MRRU is set.
o Make ``show lcp'' require context as nothing will ever change
in our MP LCP (it's auto-configured as per rfc1990).
o Initialise our LQM owner in hdlc_Init().
o Store our endpoint discriminator and authentication name at both
the datalink and multilink level and compare them when we've
finished AUTHENTICATE phase and before entering NETWORK phase.
If they don't match, close the link again.
Display the information in the appropriate ``show'' command.
o Initialise datalink::phone and datalink::fsmp.object properly
when we're cloning the link.
o Show which link we're passing LQRs on in our diagnostics.
o Reject endpoint discriminator REQs at the logical multilink
level.
o Remove the rest of our CARRIER and LINK logging setup.
first link in mp_Up().
o Bring MP and its CCP down when we enter phase TERMINATE,
and ditch everything in the incoming packet queue.
o Enable MRRU negotiation. Now, we can multilink
mode, but only with one physical link.
o Close the link if the peer PROTO REJs PROTO_MP.
o Prepend our protocol before passing a packet to
struct mp for fragmentation.
o Log info messages to DEBUG, not ERROR (oops).
o Align `show mp' output (again).
o Move Var*Version into command.c
o Remove struct pppVars (and there was much rejoicing) !
o Forward-decl some structs in .h files to avoid include
ordering requirements and remove a few more redundant
#includes.
o Our diagnostic socket has its password set in the `set socket'
line only (not in ppp.secret).
o Passwords are per server socket (*VarAuthKey are gone)
o Authority is per prompt (VarLocalAuth is gone).
o Local logging is per prompt.
o Add a `show who' command to see who's connected. No identd
routine - just a `where the connection came from' display.
o SIGUSR1 is disabled for now - we have no way of choosing a
password for the socket created :-(
Prompts are attached as a list of `struct descriptor's in
struct bundle, and serviced under the bundles descriptor
service routines. Ultimately, everything should be done
like this.
Cosmetic:
o alphabeticalise SRCS in Makefile.
o Add a few comments in command.h
TODO: Start checking that we don't overflow the descriptor sets
in select() now that we can have any number of descriptors.
o Remove bundle2lcp(), bundle2ccp() and bundle2link().
They're too resource-hungry and we have `owner pointers'
to do their job.
o Make our FSM understand LCPs that are always ST_OPENED
(with a minimum code that != 1).
o Send FSM code rejects for invalid codes.
o Make our bundle fsm_parent deal with multiple links.
o Make timer diagnostics pretty and allow access via ~t
in `term' mode (not just when logging debug) and
`show timers'. Only show timers every second in debug
mode, otherwise we get too many diagnostics to be useful
(we probably still do). Also, don't restrict ~m in term
mode to depend on debug logging.
o Rationalise our bundles' phases.
o Create struct mp (multilink protocol). This is both an
NCP and a type of struct link. It feeds off other NCPs
for output, passing fragmented packets into the queues
of available datalinks. It also gets PROTO_MP input,
reassembles the fragments into ppp frames, and passes
them back to the HDLC layer that the fragments were passed
from.
** It's not yet possible to enter multilink mode :-( **
o Add `set weight' (requires context) for deciding on a links
weighting in multilink mode. Weighting is simplistic (and
probably badly implemented) for now.
o Remove the function pointers in struct link. They ended up
only applying to physical links.
o Configure our tun device with an MTU equal to the MRU from
struct mp's LCP and a speed equal to the sum of our link
speeds.
o `show {lcp,ccp,proto}' and `set deflate' now have optional
context and use ChooseLink() to decide on which `struct link'
to use. This allows behaviour as before when in non-multilink
mode, and allows access to the MP logical link in multilink
mode.
o Ignore reconnect and redial values when in -direct mode and
when cleaning up. Always redial when in -ddial or -dedicated
mode (unless cleaning up).
o Tell our links to `staydown' when we close them due to a signal.
o Remove remaining `#ifdef SIGALRM's (ppp doesn't function without
alarms).
o Don't bother strdup()ing our physical link name.
o Various other cosmetic changes.
Increment OutPackets for any packet - not just LQRs
MFC:
o Fix a few comment typos.
o Fix ``set timeout'' usage message and documentation.
o Change ifOutPackets, ifOutOctets and ifOutLQRs to `u_int32_t's
so that they wrap correctly.
o Put the LQR in network byte order using the correct struct size
(sizeof u_int32_t, not sizeof u_long).
o Wrap LQR ECHO counters correctly.
o Don't increment OutLQR count if the last LQR hasn't been replied
to.
o Initialise last received LQR in StartLqm.
o Don't start the LQR timer if we're `disabled' and `accepted'.
o Generate LQR responses when both sides are using a timer and
we're not going to send our next LQR before the peers max timeout.
o Fix ``set timeout'' usage message and documentation.
o Change ifOutPackets, ifOutOctets and ifOutLQRs to `u_int32_t's
so that they wrap correctly.
o Put the LQR in network byte order using the correct struct size
(sizeof u_int32_t, not sizeof u_long).
o Wrap LQR ECHO counters correctly.
o Don't increment OutLQR count if the last LQR hasn't been replied
to.
o Initialise HisLqrData (last received LQR) in StartLqm.
o Don't start the LQR timer if we're `disabled' and `accepted'.
o Generate LQR responses when both sides are using a timer and
we're not going to send our next LQR before the peers max timeout.
LQR should now be fully functional.
Struct bundle will have its own struct ccp in the future
too.
o The ``set stopped'' command now requires context and doesn't
work on the IPCP FSM.
o Check if it's time to break out of our top level loop before
doing a select - otherwise, we'll select forever :-(
o Remove `struct link'::ccp (a temporary hack). It turns out
that IpStartOutput() calls link_Output() and link_Output()
incorrectly calls StartOutput() (really modem_StartOutput)
requiring the ccp knowledge so that it can call
IpStartOutput()... The end result is that the whole IP
output queue gets dumped into the modem output queue
and a pile of physical writes are done prematurely. This
makes the (original) code in main() actually work in that
it would not bother selecting() on the tun descriptor when
our modem queue length was 20 or greater. Instead, we now
make that decision based on the overall queue length.
This will need improvement later.
