it can't sleep, it can still move clean pages from the inactive queue to
the cache. Also, when a page is cached, there is no need to restart the
scan. The "next" page pointer held by vm_contig_launder() is still
valid. Finally, add a comment summarizing what vm_contig_grow_cache()
does based upon the value of "tries".
MFC after: 3 weeks
tcp_mtudisc(), which in its turn may call tcp_output(). Under certain
conditions (must admit they are very special) an infinite recursion can
happen.
To avoid recursion we can pass struct route to ip_output() and obtain
correct mtu. This allows us not to use tcp_mtudisc() but call tcp_mss_update()
directly.
PR: kern/155585
Submitted by: Andrey Zonov <andrey zonov.org> (original version of patch)
The AR9003 series NICs implement a separate RX error to signal that a
Keycache miss occured. The earlier NICs would not set the key index
valid bit.
I'll dig into the difference between "no key index bit set" and "keycache
miss".
VM_KMEM_MAX_SIZE.
The code was not taking into account the size of the kernel_map, which
the kmem_map is allocated from, so it could produce a sub-map size too
large to fit. The simplest solution is to ignore VM_KMEM_MAX entirely
and base the memguard map's size off the kernel_map's size, since this
is always relevant and always smaller.
Found by: Justin Hibbits
This behavior is recommended by RFC 4213 clause 3.2.
Sometimes fragmentation is the least evil.
For example, some Linux IPVS kernels forwards
ICMPv6 checksums to real servers incorrectly.
Reviewed by: hrs(previous version)
Approved by: kib(mentor)
MFC after: 1 week
mostly meets the guidelines set by the Intel SDM:
1. We use XRSTOR and XSAVE from the same CPL using the same linear
address for the store area
2. Contrary to the recommendations, we cannot zero the FPU save area
for a new thread, since fork semantic requires the copy of the
previous state. This advice seemingly contradicts to the advice
from the item 6.
3. We do use XSAVEOPT in the context switch code only, and the area
for XSAVEOPT already always contains the data saved by XSAVE.
4. We do not modify the save area between XRSTOR, when the area is
loaded into FPU context, and XSAVE. We always spit the fpu context
into save area and start emulation when directly writing into FPU
context.
5. We do not use segmented addressing to access save area, or rather,
always address it using %ds basing.
6. XSAVEOPT can be only executed in the area which was previously
loaded with XRSTOR, since context switch code checks for FPU use by
outgoing thread before saving, and thread which stopped emulation
forcibly get context loaded with XRSTOR.
7. The PCB cannot be paged out while FPU emulation is turned off, since
stack of the executing thread is never swapped out.
The context switch code is patched to issue XSAVEOPT instead of XSAVE
if supported. This approach eliminates one conditional in the context
switch code, which would be needed otherwise.
For user-visible machine context to have proper data, fpugetregs()
checks for unsaved extension blocks and manually copies pristine FPU
state into them, according to the description provided by CPUID leaf
0xd.
MFC after: 1 month
* wrap the RX proc calls in the RX refcount;
* call the DFS checking, fast frames staging and TX rescheduling if
required.
TODO:
* figure out if I can just make "do TX rescheduling" mean "schedule
TX taskqueue" ?
with fresh descriptors, before handling the frames.
Wrap it all in the RX locks.
Since the FIFO is very shallow (16 for HP, 128 for LP) it needs to be
drained and replenished very quickly. Ideally, I'll eventually move this
RX FIFO drain/fill into the interrupt handler, only deferring the actual
frame completion.
I was setting up the RX EDMA buffer to be 4096 bytes rather than the
RX data buffer portion. The hardware was likely getting very confused
and DMAing descriptor portions into places it shouldn't, leading to
memory corruption and occasional panics.
Whilst here, don't bother allocating descriptors for the RX EDMA case.
We don't use those descriptors. Instead, just allocate ath_buf entries.
adds an extra tick to account for the current partial clock tick. However,
that is not appropriate for a repeating timer when the exact tvtohz() value
should be used for subsequent intervals. Fix repeating callouts for
EVFILT_TIMER by subtracting 1 tick from the tvtohz() result similar to the
fix used in realitexpire() for interval timers.
While here, update a few comments to note that if the EVFILT_TIMER code
were to move out of kern_event.c, it should move to kern_time.c (where the
interval timer code it mimics lives) rather than kern_timeout.c.
MFC after: 1 month
... from a user-set persistent limit on the said level.
Allow to set the user-imposed limit below current deepest available level
as the available levels may be dynamically changed by ACPI platform
in both directions.
Allow "Cmax" as an input value for cx_lowest sysctls to mean that there
is not limit and OS can use all available C-states.
Retire global cpu_cx_count as it no longer serves any meaningful
purpose.
Reviewed by: jhb, gianni, sbruno
Tested by: sbruno, Vitaly Magerya <vmagerya@gmail.com>
MFC after: 2 weeks
