fact, use the same values here that we use on 32-bit x86 and MIPS. Some
machines were reported to have problems with the more aggressive values.
Reported and tested by: andrew
submap. Otherwise, after r246204, the auto-scaling logic in kern_malloc.c
tries to create a kmem submap that consumes the entire kernel map on a
Pandaboard with 1 GB of RAM.
Tested by: gonzo
machine to another. Therefore, VM_MAX_KERNEL_ADDRESS can't be a constant.
Instead, #define it to be a variable, vm_max_kernel_address, just like we
do on sparc64.
Reviewed by: kib
Tested by: ian
VM_KMEM_SIZE_SCALE specifies which fraction of the available physical
memory, after deduction of the kernel itself and other early statically
allocated memory, can be used for the kmem_map. The kmem_map provides
for all UMA/malloc allocations in KVM space.
Previously ARM was using a fixed kmem_map size of (12*1024*1024) = 12MB
without regard to effectively available memory. This is too small for
recent ARM SoC with more than 128MB of RAM.
For reference a description of others related kmem_map parameters:
VM_KMEM_SIZE default start size of kmem_map if SCALE is
not defined
VM_KMEM_SIZE_MIN hard floor on the kmem_map size
VM_KMEM_SIZE_MAX hard ceiling on the kmem_map size
VM_KMEM_SIZE_SCALE fraction of the available real memory to
be used for the kmem_map, limited by the
MIN and MAX parameters.
Tested by: ian
MFC after: 1 week
interrupt counts and names, by making the names into an array of fixed-length
strings that can be directly indexed. This eliminates extra memory accesses
on every interrupt to increment the counts.
As a side effect, it also fixes a bug that would corrupt the names data
if a name was longer than MAXCOMLEN, which led to incorrect vmstat -i output.
Approved by: cognet (mentor)
- Add pl310.disable tunable to disable L2 cache altogether. In
order to make sure that it's 100% disabled we use cache event
counters for cache line eviction and read allocate events
and panic if any of these counters increased. This is purely
for debugging purpose
- Direct access DEBUG_CTRL and CTRL might be unavailable in
unsecure mode, so use platform-specific functions for
these registers
- Replace #if 1 with proper erratum numbers
- Add erratum 753970 workaround
- Remove wait function for atomic operations
- Protect cache operations with spin mutex in order to prevent race condition
- Disable instruction cache prefetch and make sure data cache
prefetch is enabled in OMAP4-specific intialization
interfere with structure fields of the same name in drivers, like
the intr_disable function pointer in struct cphy_ops in cxgb(4).
Instead define intr_disable and intr_restore as inline functions.
With intr_disable() an inline function, the I32_bit and F32_bit
macros now need to be visible in MI code and given the rather
poor names, this is not at all good. Define ARM_CPSR_F32 and
ARM_CPSR_I32 and use that instead of F32_bit and I32_bit (resp)
for now.
The copies of initarm used on platforms with FDT support were almost
identical. The differences were pulled out into separate functions that
were called by initarm.
This change merges the, now identical, copies of initarm and a few of it's
support functions. This is a step towards a common kernel on ARMv6.
this some compilers will place a cmp instruction before the atomic operation
and expect to be able to use the result afterwards. By adding "cc" to the
list of used registers we tell the compiler to not do this.
problematic because some callers to pmap_kextract() expect its
implementation to be lock-less. In particular, uma_dbg_alloc() implicitly
requires this. Otherwise, lock-order reversals occur between pmap locks and
UMA zone locks. So, this change introduces a lock-less implementation of
pmap_kextract().
Disable recursion on the pvh global lock in the new armv6 pmap. While
recursion on this locks occurs in the old arm pmap, it thankfully doesn't
occur in the armv6 pmap.
Tested by: jmg
On single core devices set_stackptrs is only ever called with cpu = 0 in
initarm and will be identical to the existing function. On SMP this needs
to be implemented for sys/arm/mp_machdep.c, but the implementations are
identical for each SoC.
MSI are implemented via software interrupt. PCIe cards will write
into software interrupt register which will cause inbound shared
interrupt which will be interpreted as a MSI.
Obtained from: Marvell, Semihalf
- Add functions to calculate clocks instead using hardcoded values
- Update reset and timers functions
- Update number of interrupts
- Change name of platform from db88f78100 to db78460
- Correct DRAM size and PCI IRQ routing in dts file.
Obtained from: Semihalf
Cummulative patch of changes that are not vendor-specific:
- ARMv6 and ARMv7 architecture support
- ARM SMP support
- VFP/Neon support
- ARM Generic Interrupt Controller driver
- Simplification of startup code for all platforms
arm platform. Add all the atmel boards to the ATMEL kernel for
testing purposes. Until boot loader arg parsing of baord type
is done, this won't actually be able to do the runtime selection.
This is required for ARM EABI. Section 7.1.1 of the Procedure Call for the
ARM Architecture (AAPCS) defines wchar_t as either an unsigned int or an
unsigned short with the former preferred.
Because of this requirement we need to move the definition of __wchar_t to
a machine dependent header. It also cleans up the macros defining the limits
of wchar_t by defining __WCHAR_MIN and __WCHAR_MAX in the same machine
dependent header then using them to define WCHAR_MIN and WCHAR_MAX
respectively.
Discussed with: bde
usermode, using shared page. The structures and functions have vdso
prefix, to indicate the intended location of the code in some future.
The versioned per-algorithm data is exported in the format of struct
vdso_timehands, which mostly repeats the content of in-kernel struct
timehands. Usermode reading of the structure can be lockless.
Compatibility export for 32bit processes on 64bit host is also
provided. Kernel also provides usermode with indication about
currently used timecounter, so that libc can fall back to syscall if
configured timecounter is unknown to usermode code.
The shared data updates are initiated both from the tc_windup(), where
a fast task is queued to do the update, and from sysctl handlers which
change timecounter. A manual override switch
kern.timecounter.fast_gettime allows to turn off the mechanism.
Only x86 architectures export the real algorithm data, and there, only
for tsc timecounter. HPET counters page could be exported as well, but
I prefer to not further glue the kernel and libc ABI there until
proper vdso-based solution is developed.
Minimal stubs neccessary for non-x86 architectures to still compile
are provided.
Discussed with: bde
Reviewed by: jhb
Tested by: flo
MFC after: 1 month
layer, but it is read directly by the MI VM layer. This change introduces
pmap_page_is_write_mapped() in order to completely encapsulate all direct
access to PGA_WRITEABLE in the pmap layer.
Aesthetics aside, I am making this change because amd64 will likely begin
using an alternative method to track write mappings, and having
pmap_page_is_write_mapped() in place allows me to make such a change
without further modification to the MI VM layer.
As an added bonus, tidy up some nearby comments concerning page flags.
Reviewed by: kib
MFC after: 6 weeks
this array either from Linux boot data, when enabled, or in the
typical way that most ports do it. arm_pyhs_avail_init is coming
soon since it must be a separate function.
redboot. Support is very preiminary and likely needs some work. Also,
do some minor code shuffling of the FreeBSD /boot/loader metadata
parsing code. This code is preliminary and should be used with
caution.
is enabled, sets values based on the metadata passed in. Otherwise
fake_preload_metadata is called. Change the default parse_boot_param
to default_parse_boot_param. Enable this functionality only on the mv
platform, which is where most of the code is from.
Reviewed by: cognet, Ian Lapore
the boot parameters from initarm first thing. parse_boot_param parses
the boot arguments and converts them to the /boot/loader metadata the
rest of the kernel uses. parse_boot_param is a weak alias to
fake_preload_metadata, which all the platforms use now, but may become
more extensive in the future.
Since it is a weak symbol, specific boards may define their own
parse_boot_param to interface to custom boot loaders.
Reviewed by: cognet@, Ian Lapore
structure with the first 4 registers to allow a wider range of boot
loaders to work. Future commits will make use of this to centralize
support for the different loaders.
