Check for partition types FS_VINUM and FS_UNUSED. Accept both, but
complain about FS_UNUSED. At a later date, only FS_VINUM will be
accepted.
Threatened-since: over a year
Add a flag `force' (VF_FORCECONFIG) to force name changes of
existing drives.
config_drive:
If the drive already has a vinum label, and name doesn't match the
specified drive, do it anyway if the 'force' flag is specified.
finish_config:
Reset the `force' flag.
Continually-tripped-over-by: Karl Pielorz <kpielorz@tdx.co.uk>
give_sd_to_drive:
If the drive is down, take the subdisk down and don't try to fix
things.
update_plex_config:
Don't try to update the config parameters of a plex which isn't
fully configured (state plex_init or plex_unallocated).
Correctly calculate the amount to trim off a striped or RAID-5 plex
whose size is not a multiple of the stripe size.
compiled with or without debugging support. This enables us to catch
(fatal) mismatches between the kernel and userland.
Coalesce flags VINUM_DISKCONFIG and VINUM_READING_CONFIG. They did
essentially the same thing.
Add VINUM_BIGDRIVE for pretending we have macho hardware.
pretends that each drive is 100 times as large as it really is. Not
for use at home.
Coalesce flags VINUM_DISKCONFIG and VINUM_READING_CONFIG. They did
essentially the same thing.
This solved a problem where 'vinum resetconfig' only reset half
the drives.
Reported-by: Brad Knowles <blk@skynet.be>
Karl Pielorz <kpielorz@tdx.co.uk>
Change the super device. We now have three super devices:
1. The normal superdevice used by vinum(8).
2. The superdevice used by vinum(8) when compiled with debug support.
3. The superdevice used by the daemon.
This method allows vinum(8) to determine debug mismatches. Also check
correctly for the device type. The old code did not check all bits of
the minor number.
Reported-by: a cast of thousands, most recently by Brad Knowles
<blk@skynet.be>.
gave yet another internal register layout model for what is
*still* the same architecture. I hope they saved billyuns of gates
'coz otherwise this is *really* annoying.
thwank in register layout goop). A different mboxcmd approach. Some PDB change
infrastructure. Some better management of loopdown/loopup events (keep them
distinct from resource starvation for simq freeze/unfreeze actions).
The old VN device broke in -4.x when the definition of B_PAGING
changed. This patch fixes this plus implements additional capabilities.
The new VN device can be backed by a file ( as per normal ), or it can
be directly backed by swap.
Due to dependencies in VM include files (on opt_xxx options) the new
vn device cannot be a module yet. This will be fixed in a later commit.
This commit delimitted by tags {PRE,POST}_MATT_VNDEV
chip int. and ext. clock synchronisation). Fixed workaround for
transmit threshold underrun. Added volatile keyword to CSR_READ_* and
CSR_WRITE_* macroses. Added DELAYs to eliminate randomness caused
by processor speed. Fixed all TXCON and RXCON registers to be accessed
only when chip is idle, as manual told. Changed epic_init_phy to
drop link by isolating and going loopback, should should force link
partner to restart autonegotiation.
PR: kern/10535, kern/9742, kern/10575
Submitted by: Peter Jeremy, David Greenman
a wierd double-queue arrangement.. It always empties the if_snd queue
then puts the transmit packets into a different queue that is limited
by the number of TX descriptors and does it's own discards...
This should stop the boot-time XXX warning anyway.
MMalloc: save the time at which the request was granted, remove more
crud.
FFree: add a circular buffer of the last 64 Free requests if
DEBUG_MEMFREE is set.
after the volume had been fully operational; involves a change in the
use of the VF_NEWBORN flag. Now if you add a plex to a volume which
is up, the plex will be down and the subdisks stale. You need to
explicitly start the subdisks, which copies data from the good
subdisks to the uninitialized ones.
Stumbled-over-by: Ludwig Pummer <ludwigp@bigfoot.com>
give_sd_to_drive:
correct method to give the entire largest chunk of drive to the
subdisk. Now it's enough to specify a length, and vinum will give
you as much as it can. Not to be recommended except for empty
drives.
Correct a bogon which made vinum refuse to give the last sector of
a drive to a subdisk.
Last-reported-by: Ludwig Pummer <ludwigp@bigfoot.com>
Change %q formats to %ll before the former go away. This doesn't make
much difference, since kernel kvprintf currently doesn't support
either, and the messages in question are just error messages.
- Refined internal interface in keyboard drivers so that:
1. the side effect of device probe is kept minimal,
2. polling mode function is added,
3. and new ioctl and configuration options are added (see below).
- Added new ioctl: KDSETREPEAT
Set keyboard typematic rate. There has existed an ioctl command,
KDSETRAD, for the same purpose. However, KDSETRAD is dependent on
the AT keyboard. KDSETREPEAT provides more generic interface.
KDSETRAD will still be supported in the atkbd driver.
- Added new configuration options:
ATKBD_DFLT_KEYMAP
Specify a keymap to be used as the default, built-in keymap.
(There has been undocumented options, DKKEYMAP, UKKEYMAP, GRKEYMAP,
SWKEYMAP, RUKEYMAP, ESKEYMAP, and ISKEYMAP to set the default keymap.
These options are now gone for good. The new option is more general.)
KBD_DISABLE_KEYMAP_LOADING
Don't allow the user to change the keymap.
Move the Olicom token ring driver to the officially sanctionned location of
/sys/contrib. Also fix some brokenness in the generic token ring support.
Be warned that if_dl.h has been changed and SOME programs might
like recompilation.
The i++ loop from 1..1000 is too small on very fast machines like
PII 450 MHz. Increasing the loop from 1..100000 lets the machine
access PHY. After this patch it's possible to use a SMC PCI card
on a HP Kayak XA series PC Workstation. Workaround until this fix
was to enable debugging in the driver (#define EPIC_DEBUG 1).
Without that patch you get an undefined state:
while true
do
ifconfig -a | grep status:
done
The status messages flaps between twwo values, but not
"connected".
Obtained from: Ustimenko Semen <semen@iclub.nsu.ru>
determine IRQ and DRQ information.
Fix a bug that would cause us to attempt to retrieve extended sync
rate information on cards/firmware revs that do not support that command.
config info. On early revision cards (742a), the EISA register space,
other than the location used to determine the address of the card's main
command ports, is write only.
reports on those most welcome!
Fixed problems:
Hang on probe on "fantom" devices.
The probe now use a timeout to avoid hangs if no interrupt
is recevied.
There has also been more general code clenaups, and some reorgs.
