print "at <not configured>" for iobase == -1 (autodetect not happens)
and not print anything for iobase == -2 (none)
Old code treat this two special config numbers as big port numbers.
<sys/ioctl_compat.h> and sometimes <sys/filio.h> instead of
<sys/ioctl.h> in tty-related files. <sys/ttycom.h> is still
usually imported bogusly via <sys/termios.h>.
and fixed everything that depended on getting it from the wrong
place. Most of the broken things actually only depended on getting
the declaration of their interrupt handler from "ioconf.h".
supports All Cyrix CPUs, IBM Blue Lightning CPU and NexGen (now AMD)
Nx586 CPU, and initialize special registers of Cyrix CPU and msr of
IBM Blue Lightning CPU.
If revision of Cyrix 6x86 CPU < 2.7, CPU cache is enabled in
write-through mode. This can be disabled by kernel configuration
options.
Reviewed by: Bruce Evans <bde@freebsd.org> and
Jordan K. Hubbard <jkh@freebsd.org>
form `tv = time'. Use a new function gettime(). The current version
just forces atomicicity without fixing precision or efficiency bugs.
Simplified some related valid accesses by using the central function.
can't perform overlapping commands on both of its channels.
To enable the CMD640B work-around, the kernel must be compiled with
"options CMD640". Without that option there should be no difference
in the code produced compared to the previous revision of wd.c.
Submitted by: Wolfgang Helbig <helbig@ba-stuttgart.de>
effect immediately, but required a following (normally redundant) G0
into GL mapping. This adds one layer of indirection (thus might make it
slower), but fixes the broken box character drawing in pcvt.
Hellmuth and Bruce are unfortunately too busy too review this right now,
but i wanna have it in 2.2 since it has often been asked in the past.
Warning: this won't work yet with PCVT_SCANSET=2 along in early
console mode (boot -c, or boot -d).
A big thanks to Kazutaka, and a word of apologies for delaying the
review for that long time...
Submitted by: yokota@zodiac.mech.utsunomiya-u.ac.jp (Kazutaka YOKOTA)
valid signals, else return EINVAL for ioctl VT_SETMODE.
this fixes a problem that anybody with vty access can panic the system.
2.2-Candidate (and 2.1.0 I believe)
Reviewed-by: sos
available in buffer when buffer was completely empty.
It now correctly reports the total buffer space available.
Reviewed by: jkh, davidg
Obtained from: Linux 1.3.20's sound driver code
changes, so don't expect to be able to run the kernel as-is (very well)
without the appropriate Lite/2 userland changes.
The system boots and can mount UFS filesystems.
Untested: ext2fs, msdosfs, NFS
Known problems: Incorrect Berkeley ID strings in some files.
Mount_std mounts will not work until the getfsent
library routine is changed.
Reviewed by: various people
Submitted by: Jeffery Hsu <hsu@freebsd.org>
The PS/2 mouse device responds to a reset command with a sequence of
ACK(fa), RESULT(aa) and ID(00). Most PS/2 mice immediately returns
ACK, but spend sometime before sending RESULT. The Armada takes time
before ACK; extra delay is necessary before the call to read ACK.
The problem was reported in comp.unix.bsd.freebsd.misc and the patch
was tested by the reporter. No PR was filed, by the way.
with <= 100 usec between each character arrival time. This didn't happen
until rev.1.75 of clock.c because DELAY(100) used to delay for closer to
80 usec than 100 usec, and the minimum time between character arrivals is
87.8 usec at the maximum supported speed of 115200 bps 8N1.
Clear DCD timestamp flag on close (the input timestamp flag is already
cleared).
key "print scrn".
It used to stop at the first non-open vty, now it skips the non-open
ones and thereby enable one to cycle around all open vty by pressing
"print scrn".
I have code to calibrate the overhead fairly accurately, but there
is little point in using it since it is most accurate on machines
where an estimate of 0 works well. On slow machines, the accuracy
of DELAY() has a large variance since it is limited by the resolution
of getit() even if the initial delay is calibrated perfectly.
Use fixed point and long longs to speed up scaling in DELAY().
The old method slowed down a lot when the frequency became variable.
Assume the default frequency for short delays so that the fixed
point calculation can be exact.
Fast scaling is only important for small delays. Scaling is done
after looking at the counter and outside the loop, so it doesn't
decrease accuracy or resolution provided it completes before the
delay is up. The comment in the code is still confused about this.
- don't uselessly initialize the fifo "DMA" bit at attach time.
- initialize the fifo "DMA" bit at open time. Without this, the device
interrupts for every character received, reducing input performance
to that of an 8250.
- don't uselessly initialize the fifo trigger level to 8 (scaled to
256) at attach time.
- don't scale the fifo trigger level to 512 bytes. The driver's pseudo-
dma buffer has size 256, so it can't handle bursts of size 512 or 256.
It should be able to handle the second lowest ftl (2 scaled to 64).
- don't reset the fifos in siostop(). Reset triggers a hardware bug
involving wedging of the output interrupt bit This workaround
unfortunately requires ESP support to be configured.
an X seesion. Really stupid error of me, and I've been looking at
this code SO many times. Thanks to Kazutaka YOKOTA for seeing this..
Submitted by: Kazutaka YOKOTA
one in draw_mouse causes spontanious hangs on my p5-100 when I
move the mouse excessively. Forgot that on the last commit, so
using the mouse or destructive cursor would produce large amounts
of flicker..
cur_console is NULL when copy_font() is first called from scinit(). This
is apparently harmless when scinit() is called early from sccninit() -
page 0 is apparently mapped r/w then, and 0->status contains suitable
garbage. However, when there is a serial console, scinit() is first
called from scattach() when the page tables are completely initialized,
so the NULL pointer causes a panic.
Submitted by: bruce
called early for console i/o. The timer is usually in BIOS mode
if it isn't explicitly initialized. Then it counts twice as fast
and has a max count of 65535 instead of 11932. The larger count
tended to cause infinite loops for delays of > 20 us. Such delays
are rare. For syscons and kbdio, DELAY() is only called early
enough to matter for ddb input after booting with -d, and the delay
is too small to matter (and too small to be correct) except in the
PC98 case. For pcvt, DELAY() is not used for small delays (pcvt
uses its own broken routine instead of the standard broken one),
but some versions call DELAY() with a large arg when they unnecessarily
initialize the keyboard for doing console output. The problem is
more serious for pcvt because there is always some early console
output.
Guard against the i8254 timer being partially or incorrectly
initialized. This would have prevented the endless loop.
Should be in 2.2.
I have no idea if this works since I don't have one of the cards to test.
I also don't know what the LINT and GENERIC entries should look like,
so I just made up some values for now and left them commented out.
Someone who knows the factory settings for a Pro/10, please contact me!
Submitted-By: Javier Martín Rueda <jmrueda@diatel.upm.es>
This will make a number of things easier in the future, as well as (finally!)
avoiding the Id-smashing problem which has plagued developers for so long.
Boy, I'm glad we're not using sup anymore. This update would have been
insane otherwise.
previous hackery involving struct in_ifaddr and arpcom. Get rid of the
abominable multi_kludge. Update all network interfaces to use the
new machanism. Distressingly few Ethernet drivers program the multicast
filter properly (assuming the hardware has one, which it usually does).
wdparams from short into u_short. If wdp_cylinders is short, it
overflows and cause serious sign extension bug when large IDE HDD is
used. These members are only used for initialization of u_long
variables in both 3.0-current and RELENG_2_2 branch.
I believe this should be in 2.2.
Reviewed by: Bruce Evans <bde@zeta.org.au>
taken from the voxware-3.5 distribution. Also some changes to the SB
and MPU IRQs to reflect more common/default settings.
Submitted-By: Brian Campbell <brianc@netrover.com>
at device attach time, instead of allocating and freeing buffers as
necessary. But he or she forgot to remove the line that invalidated
the buffer when the device is closed. Therefore, after using the
device for the first time, the buffer was incorrectly invalidated and
that caused a page fault on the second, and subsequent uses.
Closes PR # kern/2319: Using Genius GS-4500 scanner...
Submitted by: jmrueda@diatel.upm.es (Javier Martmn Rueda)
is still broken - it doesn't restore the floating point state.
2.2-BETA users should disable it using npx0 flags 0x04 the same as
2.2-ALPHA users should have.
Closes PR # kern/1065.
While i was at it, also reject IO requests that are not an integer
multiple of the device blocksize.
Submitted by: vak@crox.net.kiae.su (Serge V.Vakulenko)
Confirmed by: Georg-W. Koltermann (gwk@cray.com)
workings of #error in particular. He also broke the 2.2 build with this
change, leading me to wonder whether or not the changes were ever even
tested. Folks, I'm happy to see people work directly on 2.2 like
this and will continue to encourage Nate to make direct commits, but
please TEST before committing! I think that's a more than reasonable
prerequisite, and this code could never have worked at all, leading me to
believe that Nate skipped this most basic of steps.
Don't allow people to use the 'dedicated' drivers at the same time as
the generic support code, as it can cause all sorts of problems
including kernel crashes.
[ definite 2.2 material ]
to TAILQs. Fix places which referenced these for no good reason
that I can see (the references remain, but were fixed to compile
again; they are still questionable).
type to be int so that errors can be returned.
2) Use the new SIOCSIFMTU ether_ioctl support in the few drivers that are
using ether_ioctl().
3) In if_fxp.c: treat if_bpf as a token, not as a pointer. Don't bother
testing for FXP_NTXSEG being reached in fxp_start()...just check for
non-NULL 'm'. Change fxp_ioctl() to use ether_ioctl().
function ed_attach_NE2000_pci() in if_ed.c passes
an uninitialized block of memory (got with malloc())
to ed_attach. This prevents a proper initialization
of the device descriptor and in my case causes a panic
during the probe, while printing out device info.
Reviewed by: phk
Submitted by: Luigi Rizzo <luigi@iet.unipi.it>
1. All the suggestions earlier made by Bruce: renaming some symbols,
stricter error checking, removing redundant code, etc.
2. The `psm' driver preserves the default counter resolution and
report rate, whatever they are after reset. (Based on reports and
suggestion from Nate and Rob Bolin).
3. The `psm' driver now does not check the so-called sync. bit in the
first byte of the data packet by default, so that the tapping feature
of ALPUS GlidePoint works (based on reports from Louis Mamakos). I
tested the code with ALPUS Desktop GlidePoint (M/N GP101) and found
no problem; tapping worked. It appears ALPUS produces several models
of GlidePoint. I hope the other models are OK too.
The check code can still be activated by defining the PSM_CHECKSYNC
option in the config file. (The bit checking slightly reduces, if not
completely eliminates, weird mouse behavior cased by unsynchronized
mouse data packets. It also helps us to detect if the mouse interrupt
can ever be lost. But, well, if there are devices which cannot be
supported this way...)
4. The `psm' driver does not include the protocol emulation code by
default. The code can still be compiled in if the PSM_EMULATION option
is specified in the config file. Louis Mamakos suggests the emulation
code is putting too much in the kernel, and `moused' works well.
I will think about this later and decide if the entire emulation
code should be removed.
5. And, of course, the fix in `scprobe()' from Bruce to cure the
UserConfig problem. My code in `kbdio.c' is slightly different from
his patch, but has the same effect. There still is a possibility that
`scprobe()' gets confused, if, for whatever reasons, the user holds
down a key for very long time during the boot process. But we cannot
cope with everything, can we?
Submitted by: Kazutaka YOKOTA (yokota@zodiac.mech.utsunomiya-u.ac.jp)
are always together with Framing Errors and they were incorrectly
treated as FE's and discarded.
Reorganized the BREAK/FE/PE tests.
Found by: NIST-PCTS
with sio devices (not perfectly, since there is no way to flush the tx
holding register on 8250-16450's. I'm not sure if resetting the fifos
flushes the tx shift register).
Reminded by: NIST-PCTS
is completely empty. There is no interrupt for output completion, so
poll for it every 10 ms after output is nearly complete. Now ttywait()
works right.
Reminded by: NIST-PCTS
The 'getchar' function in syscons (sccngetc) is used by UserConfig to
get keyboard input from the user. When it was modified to use the
shared keyboard port routines it used the port passed in during the
probe routine. Since the probe routine was not yet called, the port was
set to 0, which is obviously not going to work.
Pre-initialize sc_port to IO_KBD which is really a kludge, but it's how
the previous driver did it's job.
Found by: remote GDB
user supplies a bad address, because they push a lot of stuff that the
fault handler doesn't know about onto the stack. This has been broken
for more than half a year despite being tested for almost half a year
in -current.
with the copyright stuff fixed so soon (this should be merged into 2.2 when
you have a chance, Poul).
This is the new AWE32 driver, with support for the AWE32's fancy MIDI
synthesizer. The utilities for this will appear as port submissions soon
afterwards, according to the submitter.
Submitted-By: Randall Hopper <rhh@ct.picker.com>
Written-By: Takashi Iwai <iwai@dragon.mm.t.u-tokyo.ac.jp>
routines. An older version of this was tested successfully on all of my
systems with PS/2 mice. This was brought in without testing because it
is necessary due to the previously committed syscons changes.
Submitted by: Kazutaka Yokota <yokota@zodiac.mech.utsunomiya-u.ac.jp>
syscons and psm, curtesy Kazutaka Yokota with minor changes by
me. This contains an update of the psm driver as well.
This also fixes the breakage that I introduced to the psm driver by
making syscons poll for keyboard events in the atempt to fix the
hanging keyboard problem.
It works perfectly for me, and I'd like to hear from all that
have had keyboard/ps/2 mouse problems if this is the cure...
Submitted by: Kazutaka YOKOTA (yokota@zodiac.mech.utsunomiya-u.ac.jp)
wdreg.h: Delete wd_ctlr macro. PC98 version of wd.c treats it as a
variable.
GENERIC98: Delete ep0 entry. Current ep driver write I/O port 0x100.
This clobbers ICW of i8259, because upper 8bits of address line is not
masked on mother board.
if_fe.c: Merge from revision 1.18 of sys/i386/isa/if_fe.c.
pc98.c: Globalize dmapageport, because SCSI driver use this
variable.
wd82371.c: Yet another merge.
These are 2.2 candidates.
Submitted by: The FreeBSD(98) Development Team
almost complete control over RTS (control of its initial value is still
missing).
This fixes PR 1644 for sio.
The author of PR 1644 wants it in 2.1.6 and 2.2. This may be safe since
the complications are only in rarely used cases that I hope I've covered.
sys/pc98/i386/machdep.c: sync with i386/i386/machdep.c
sys/pc98/conf/options.pc98: sync with i386/conf/options.i386
sys/i386/isa/sound: DMA auto initialize mode support for PC98.
contributed by: Akio Morita <amorita@bird.scphys.kyoto-u.ac.jp>
Definite 2.2 material, I believe.
Submitted by: The FreeBSD (98) Development Team
actually harmless.
2. Fixed code to match comment in scintr().
3. Don't allow even root to take control of the machine when securelevel > 0.
I've secured the accesses to PSL_IOPL in all drivers and asked pst to
review it, but he seems to be busy. Write access to /dev/kmem and
other critival devices currently leaks across raisings of securelevel
via open fd's, so there may as well be a similar leak for PSL_IOPL.
4. (Most important.) Don't corrupt memory beyond the screen buffers if
the cursor happens to be off the 80x25 screen when syscons starts.
5. Fix console cursor update (not perfect yet).
Submitted by: bruce
~
getting the same behavior using the flags, which can be done inside of
UserConfig. (Also document other syscons flags which were previously
undocumented).
Requested by: bde
negative-logic flags (flags 0x01 and 0x02 for npx0, defaulting to unset = on).
This changes the default from off to on. The options have been in current
for several months with no problems reported.
Added a boot-time negative-logic flag for the old I5886_FAST_BCOPY option
which went away too soon (flag 0x04 for npx0, defaulting to unset = on).
Added a boot-time way to set the memory size (iosiz in config, iosize in
userconfig for npx0).
LINT:
Removed old options. Documented npx0's flags and iosiz.
options.i386:
Removed old options.
identcpu.c:
Don't set the function pointers here. Setting them has to be delayed
until after userconfig has had a chance to disable them and until after
a good npx0 has been detected.
machdep.c:
Use npx0's iosize instead of MAXMEM if it is nonzero.
support.s:
Added vectors and glue code for copyin() and copyout().
Fixed ifdefs for i586_bzero().
Added ifdefs for i586_bcopy().
npx.c:
Set the function pointers here.
Clear hw_float when an npx exists but is too broken to use.
Restored style from a year or three ago in npxattach().
This allows the user to add modify syscons's configuration flags using
UserConfig that will allow older/quirky hardware (most notably older IBM
ThinkPad laptops) to work with the standard boot kernel.
Inspired by: The Nomads
handlers if interrupts are nested more than a few (3) deep. This
only reduces the maximum nesting level by 1 with the standard
drivers unless there is a related bug somewhere, but can't hurt
much (the worst case is returning to hoggish interrupt handler like
wdintr(), but such interrupt handlers hurt anyway).
Fixed a previously harmless race incrementing the interrupt nesting
level.
This should be in 2.1.6 and 2.2.
hardware interrupt counts add up to the total. Previously, software
interrupts generated by splz() were counted in the total. These
software interrupts seem to be very rare - there have apparently been
0 of them on freefall among the last 352448857 interrupts.
appearance of this bug was the malfunctioning -M option in GNU tar (it
worked only by explicitly specifying -L).
Reviewed by: bde, and partially corrected accoring to his comments
Candidate for 2.2, IMHO even for 2.1.6.
changes to the keyboard code in pcvt, this update_led() very often
caused pcvt to hang early at boot time.
(Eventually, a better solution should be found, but the simple
omission serves well as a workaround for something that is actually a
show-stopper class problem.)
Candidate for 2.2.
(1) deleted #if 0
pc98/pc98/mse.c
(2) hold per-unit I/O ports in ed_softc
pc98/pc98/if_ed.c
pc98/pc98/if_ed98.h
(3) merge more files by segregating changes into headers.
new file (moved from pc98/pc98):
i386/isa/aic_98.h
deleted:
well, it's already in the commit message so I won't repeat the
long list here ;)
Submitted by: The FreeBSD(98) Development Team
(1) Add #ifdef PC98:
sys/pc98/boot/biosboot/boot2.S
(2) Fix bug that made it impossible to boot from sd's other than unit 0:
sys/pc98/boot/biosboot/sys.c
(3) Delete redundant $Id$:
sys/pc98/pc98/clock.c (reject$B$5$l$k$+$b$7$l$J$$(B)
(4) unt -> u_int:
sys/pc98/pc98/if_ed.c
(5) Add support for rebooting by the hot-key sequence:
sys/pc98/pc98/kbdtables.h
(6) Display now looks like PC/AT version:
sys/pc98/pc98/npx.c
(7) Change comment to match that of PC/AT version:
sys/pc98/pc98/pc98.c
(8) Add function prototypes:
sys/pc98/pc98/pc98_machdep.c
(9) Include PC98 headers:
sys/pc98/pc98/sound/adlib_card.c
sys/pc98/pc98/sound/audio.c
sys/pc98/pc98/sound/dev_table.c
sys/pc98/pc98/sound/dmabuf.c
sys/pc98/pc98/sound/midi_synth.c
sys/pc98/pc98/sound/midibuf.c
sys/pc98/pc98/sound/opl3.c
sys/pc98/pc98/sound/oatmgr.c
sys/pc98/pc98/sound/sb16_dsp.c
sys/pc98/pc98/sound/sb16_midi.c
sys/pc98/pc98/sound/sb_card.c
sys/pc98/pc98/sound/sb_dsp.c
sys/pc98/pc98/sound/sb_midi.c
sys/pc98/pc98/sound/sb_mixer.c
sys/pc98/pc98/sound/sequencer.c
sys/pc98/pc98/sound/sound_config.h
sys/pc98/pc98/sound/sound_switch.c
sys/pc98/pc98/sound/soundcard.c
sys/pc98/pc98/sound/sys_timer.c
(10) Merge in PC98 changes:
sys/i386/isa/sound/os.h
(11) Deleted as result of 9. and 10. above:
sys/pc98/pc98/sound/ad1848_mixer.h
sys/pc98/pc98/sound/aedsp16.c
sys/pc98/pc98/sound/coproc.h
sys/pc98/pc98/sound/finetune.h
sys/pc98/pc98/sound/gus_hw.h
sys/pc98/pc98/sound/gus_linearvol.h
sys/pc98/pc98/sound/hex2hex.h
sys/pc98/pc98/sound/mad16.h
sys/pc98/pc98/sound/midi_ctrl.h
sys/pc98/pc98/sound/midi_synth.h
sys/pc98/pc98/sound/opl3.h
sys/pc98/pc98/sound/os.h
sys/pc98/pc98/sound/pas.h
sys/pc98/pc98/sound/sb_mixer.h
sys/pc98/pc98/sound/soundvers.h
sys/pc98/pc98/sound/tuning.h
Submitted by: The FreeBSD(98) Development Team
Check that a received packet isn't longer than MCLBYTES. This will
sometimes happen if a cable is plugged into or removed from a live
system.
Try to cater better for early receive interrupts.
TIMER_FREQ.
Fixed missing splx() in scrn_timer(). The bug was harmless because of the
undocumented behaviour that the ipl is automatically restored for timeout
functions (see softclock()). Perhaps we should depend on this behaviour.
Fixed the ddb fix in rev.1.176. The in_debugger flag was no use because
it only works when the debugger is entered via the keyboard hotkey. The
debugger may be entered for breakpoints and traps, and the console putc
routine has no way of knowing when it was, so the console putc routine
must (almost?) always remove the cursor image.
Not fixed: console switching in ddb doesn't work (ISTR it working), and
console 0 shouldn't be switched to for the debugger hotkey unless console
0 is /dev/console.
Fixed side effects from calling add_keyboard_randomness() in the console
getc routine by not calling it. add_keyboard_randomness() currently
always reenables interrupts on 386's and 486's. This is very bad if the
console getc routine is called from the debugger and the debugger was
entered with interrupts disabled.
Fixed preservation of initial screen and now-bogus comment about it. It
was broken by setting the initial scr_buf to `buffer' instead of Crtat.
`buffer' was full of nulls and the first scroll cleared everything above
the things written through syscons.
Submitted by: bruce (bde@freebsd.org)
bit (0x0008) in the sc driver configuration line. This way it's easy to
boink a generic kernel.
Also, document and place in an opt_ file the #define's for overriding which
serial port is the system console.
Approved by: sos
there is keyboard input.
The mousepointer is shown again immediately if moved.
Also a function pointer used to install a userwritten extra
ioctl handler (sc_user_ioctl). This way its is possible to
install user defined videomodes etc etc. No further changes
should be in the kernel.
- use a more accurate and more efficient method of compensating for
overheads. The old method counted too much time against leaf
functions.
- normally use the Pentium timestamp counter if available.
On Pentiums, the times are now accurate to within a couple of cpu
clock cycles per function call in the (unlikely) event that there
are no cache misses in or caused by the profiling code.
- optionally use an arbitrary Pentium event counter if available.
- optionally regress to using the i8254 counter.
- scaled the i8254 counter by a factor of 128. Now the i8254 counters
overflow slightly faster than the TSC counters for a 150MHz Pentium :-)
(after about 16 seconds). This is to avoid fractional overheads.
files.i386:
permon.c temporarily has to be classified as a profiling-routine
because a couple of functions in it may be called from profiling code.
options.i386:
- I586_CTR_GUPROF is currently unused (oops).
- I586_PMC_GUPROF should be something like 0x70000 to enable (but not
use unless prof_machdep.c is changed) support for Pentium event
counters. 7 is a control mode and the counter number 0 is somewhere
in the 0000 bits (see perfmon.h for the encoding).
profile.h:
- added declarations.
- cleaned up separation of user mode declarations.
prof_machdep.c:
Mostly clock-select changes. The default clock can be changed by
editing kmem. There should be a sysctl for this.
subr_prof.c:
- added copyright.
- calibrate overheads for the new method.
- documented new method.
- fixed races and and machine dependencies in start/stop code.
mcount.c:
Use the new overhead compensation method.
gmon.h:
- changed GPROF4 counter type from unsigned to int. Oops, this should
be machine-dependent and/or int32_t.
- reorganized overhead counters.
Submitted by: Pentium event counter changes mostly by wollman
controllers, it is an error to issue a command before the keyboard
has had time to reply to the previous command. Setting the LEDs
involves issueing 2 commands, so it never worked on these keyboards.
Fixed resetting of keyboard. It is possible for unprocessed
scancodes to be present when the reset routine is called. This
usually occurs after switching from one console driver to another
in userconfig. pcvt and syscons attempt to flush any stale scancodes,
but sometimes fail to do so because keyboard and/or keyboard
controller takes a long time to send the scancodes after reset
(scancodes are apparently not flushed by reset!). syscons handles
this later by not checking for errors at strategic places, but pcvt
was confused.
Use an impossible initial and failure mode setting for the LEDs
so that the LEDs always get set if they are possibly out of sync.
Added missing spltty() in update_led().
(1) Merged i386/i386/sb.h, deleted pc98/pc98/sb.h.
(2) pc98/conf/GENERIC8 looks more like i386/conf/GENERIC now.
(3) Fixed display bug in pc98/boot/biosboot/io.c.
(4) Prepare to merge memory allocation routines:
pc98/i386/locore.s
pc98/i386/machdep.c
pc98/pc98/pc98_machdep.c
pc98/pc98/pc98_machdep.h
(5) Support new board "C-NET(98)":
pc98/pc98/if_ed98.h
pc98/pc98/if_ed.c
(6) Make sure FPU is recognized for non-Intel CPUs:
pc98/pc98/npx.c
(7) Do not expect bss to be zero-allocated:
pc98/pc98/pc98.c
Submitted by: The FreeBSD(98) Development Team
I have only tested the ABP5140 card and only with a single CDROM drive
but it seems to work fine. This driver relies on features found only in
the SCSI branch so will not work in -current until those changes
are brought in. It also doesn't have any error handling code *yet*.
The goal is to use this driver as the development platform for the new
generic SCSI layer error recovery/handling code.
PCI and EISA front ends will show up as soon as I get my hands on
the cards. There are also a few issues in the driver that I need
to clear up with AdvanSys before I can suggest sticking one of
these cards in your server. 8-)
Thanks to AdvanSys for releasing this code under a suitable copyright.
Obtained from: Ported from the Linux driver writen by
bobf@advansys.com (Bob Frey).
divisor latch registers if the registers wouldn't change.
Use the default console cfcr setting while setting the divisor
latch registers for console i/o. Input may be messed up by
transiently changing the cfcr.
Use a usual cfcr setting while setting the divisor latch registers
in the probe. This shouldn't matter, but this is not the place to
test the UART's handling of 5 bit words.
Removed a stale devfs comment.
- don't include <sys/ioctl.h> in any header. Include <sys/ioccom.h>
instead. This was already done in 4.4Lite for the most important
ioctl headers. Header spam currently increases kernel build
times by 10-20%. There are more than 30000 #includes (not counting
duplicates) for compiling LINT.
- include <sys/types.h> if and only it is necessary to make the header
almost self-sufficient (some ioctl headers still need structs from
elsewhere).
- uniformized idempotency ifdefs. Copied the style in the 4.4Lite
ioctl headers.
It is needed for implementation details but very little of it is
needed for the interface. Include it in the few places that didn't
already include it.
Include <sys/ioccom.h> in <sys/disklabel.h> (as already in
<sys/diskslice.h>) so that all the disk-related headers are almost
self-sufficient.
instead of 0 if there is no input.
pcvt_drv.c:
Partially fixed pccncheckc(). It returned a boolean value instead of
the character that it fetches from the input fifo (if any). I think
it still discards characters after the first for multi-char input.
instead of 0 if there is no input.
syscons.c:
Added missing spl locking in sccncheckc(). Return the same value as
sccngetc() would. It is wrong for sccngetc() to return non-ASCII, but
stripping the non-ASCII bits doesn't help.
still being used just to support printing of the device name in the
probe. Restored the method used in rev.1.6 and changed it to print
the same strings as the previous revision.
Reviewed by: Paul Richards
(1) Add PC98 support to apm_bios.h and ns16550.h, remove pc98/pc98/ic
(2) Move PC98 specific code out of cpufunc.h (to pc98.h)
(3) Let the boot subtrees look more alike
Submitted by: The FreeBSD(98) Development Team
<freebsd98-hackers@jp.freebsd.org>
and xdm, possibly in general.
What was happening was that the server was doing a tcsetattr(.. TCSADRAIN)
on the mouse fd after a write. Since /dev/sysmouse had a null t_oproc,
the drain failed with EIO. Somehow this spammed XFree86 (!@&^#%*& binary
release!!), and the driver was left in a bogus state (ie: switch_in_progress
permanently TRUE).
The simplest way out was to implement a dummy scmousestart() routine to
accept any characters from the tty system and toss them into the void.
It would probably be more correct to intercept scwrite()'s to the mouse
device, but that's executed for every single write to the screen.
Supplying a start routine to eat the characters is only executed for the
mouse port during startup/shutdown, so it should be faster.
-I- to CFLAGS. <sb.h> must currently be used to give the version
of sb.h in the current directory, while "sb.h" in the buggy version
gave the (wrong) version in the source directory. Searching in the
source directory first is normal, but is the reverse of the order
suggested by the 4.4Lite2 #include style. -I- will remove the
ambiguities.
This enables other consumers of the mouse, to get it info via
moused/syscons.
In order to use it run moused (from sysconfig), and then tell
your Xserver that it should use /dev/sysmouse (mknod sysmouse c 12 128)
and it a mousesystems mouse. Everybody will be happy then :)
Remember that moused still needs to know what kind of mouse you
have..
Comments welcome, as is test results...
(A pointer to a const was misused to avoid loading loading the same
value twice, but gcc does exactly the same optimization automatically.
It can see that the value hasn't changed.)
If you define this, it means your keyboard is actually probable using the
brain-dammaged probe routine in syscons, and if the keyboard is NOT found,
then you don't want syscons to activate itself further.
This makes life sane for those of us who use serial consoles most of the
time and want "the right thing" to happen when we plug a keyboard in.
(1) Remove mk30line (moved to /usr/sbin, but not in our source tree yet)
(2) Delete unneeded (well, harmful now :) code to prohibit #including
of isa_device.h from PC98 sources.
(3) Remove files now equal to their ISA/PC-AT counterparts.
Submitted by: The FreeBSD(98) Development Team
during phk's staticize/cleanup commits. pstat needs it, the MAXCONS
option is not visible anywhere else, and pstat uses it to find the bounds
of the sccons[MAXCONS] array, which varies.
. preserve a multi-char sequence in a small static buffer inside
pccngetc(), so it won't be clobbered later (used to happen when
breaking into DDB user Ctrl-Alt-ESC), and
. simplify the ``keystroke is present'' determination in sgetc(), thus
making pccncheck() actually working without waiting for a keystroke.
for work regardless of whether there was an interrupt. This needs more
work, it should be able to run better when there are more than 3 host
cards present, ie: all cards in polling-only mode with no IRQ. (The
host cards have a choice of 3 irq's, 11, 12, or 15, or just polling)
little more reliably. So far I've received a couple of positive
responses and no objections to these changes.
There are two one-line changes:
- In wdprobe(), when testing the error status of drives, don't
unconditionally decide that there is no controller present if we
read back a value of 0x81 (drive 0 okay, drive 1 failed) twice
in a row. This may be caused by having an ATAPI CD-ROM jumpered
as a master on the controller with no slave.
- In wdgetctlr(), when checking for a status of WDCS_READY, check the
value twice. The first time may be bogus. This stops a phantom wd2
device from being detected when an ATAPI CD-ROM is attached to the
secondary controller alone as a slave. (This can cause installation to
fail when sysinstall attempts to open the phantom device and wedges the
system as a result. This has bitten me a couple of times on some
Gateway 2000 machines.)
. make pccncheck() work even when interrupts are disabled, so the
``Press a key on the console...'' procedure will work,
. make kernel colors #ifndef, so they can be overridden from the
config file,
. use shutdown_nice() instead of cpu_reset() if Ctrl-Alt-Del is
enabled,
. allow pccngetc() to return more than a single character, so the
arrow keys will work (and thus visual UserConfig!),
. fix a warning.
This closes all know PRs related to pcvt, in particular #845, #1236,
and #1265. PR #991 is a duplicate for 845, and PR #1283 has already
been fixed earlier in rev 1.11 of pcvt_conf.h.
Submitted by: Ulf Kieber (kieber@sax.de), for the kernel color fix
and then never accept for sending packet from upper layer anymore
(i.e. ping -f )
Reviewed by: David Greenman <dg@root.com>
Submitted by: amurai@spec.co.jp
blocked in a write() while waiting for the output to drain, sleep only
for tp->t_timeout, not forever. This only seems to happen when there is
either a modem lockup holding the hardware flow control down, or due to
some problem in the driver with processes attempting to write after the
modem has hung up (eg: elm, tf).
Saves about 280 butes of source per driver, 56 bytes in object size
and another 56 bytes moves from data to bss.
No functional change intended nor expected.
GENERIC should be about one k smaller now :-)
#ifdef DIAGNOSTIC case, and a warning only otherwise.
People who want them to break into the debugger can always set the
breakpoint explicitly. The existing behaviour was a misfeature from
the beginning, in the (wrong) assumption that the SCSI controller must
always be of essential importance to the entire system.
make it more intelligible, improve the partially bogus locking, and
allow for a ``quick re-acquiration'' from a pending release of timer 0
that happened ``recently'', so it was not processed yet by clkintr().
This latter modification now finally allows to play XBoing over
pcaudio without losing sounds or getting complaints. ;-) (XBoing
opens/writes/closes the sound device all over the day.)
Correct locking for sysbeep().
Extensively (:-) reviewed by: bde
of this patch, which had not actually been reviewed by Joerg or Paul!
(I'll better stop committing files after midnight ...)
I'm now commiting the latest code, which has been reported to work.
Minor correction to the previous commit message for this file:
The first PCI Lance in a system will get a name of lnc1, the second
will be known as lnc2 and so on. An arbitrary number of cards is
supported in a system ...
before attaching. Without this fix, 3c579(EISA) never make
any H/W inturrupt.
Reviewed by: "Justin T. Gibbs" <gibbs@freefall.freebsd.org>, nao@sbl.cl.nec.co.jp and owner-current on mailing list ;-)
Submitted by: amurai@spec.co.jp, nao@sbl.cl.nec.co.jp
This code applies to several systems with integrated Ethernet
chip, for example from HP or Compaq. It should also support
PCI Ethernet cards based on the AMD PCI Lance chip.
This code has been reviewed (visually) by Paul Richards and
tested (using an ISA Lance board) by Joerg Wunsch.
Since the parameters to nearly each and every single function
had to be changed (generally from unit number to lnc_soft*),
there is some potential for buglets having crept in ...
BEWARE: If you had lnc0 configured to have the ISA probe find
your PCI Lance, then it should now be found by the PCI probe,
and should be automatically configured as pci1 (!!! note the "1").
Reviewed by: paul, joerg
(author's explaination):
Bit 15 is the flag to request a transmit complete interrupt. The
driver was apparently written to minimize interrupts, and if not for a
3-COM design quirk, everything would be just ducky.
Prior to loading the outbound packet into the FIFO, the driver checks
to see if there's enough space to contain the packet. If not, the
driver requests a transmit-available interrupt when there is
sufficient room. Unfortunately, the card is continuing to process the
prior FIFO, and by the time the driver sets the threshold for a
transmit available interrupt, the space is already available. When
this occurs, the 3COM card ignores the interrupt request, and the
driver is hung waiting for an interrupt that will never occur.
There's probably a more elegant solution, but requesting the transmit
complete interrupt was the easiest to implement. An alternative fix
might be to check free FIFO space again, after requesting the transmit
available interrupt, but I haven't bothered pursuing this. Since the
patch, my 3C590 (PCI, same FIFO interface as 3C509) has been rock
solid.
Submitted by: mevans@candle.com (Mike Evans)
based on the HD64570 chip. Both the 1 and 2 port cards is supported.
Line speeds of up to 2Mbps is possible. At this speed about 95% of the
bandwidth is usable with 486DX processors.
The standard FreeBSD sppp code is used for the link level layer. The
default protocol used is PPP. The Cisco HDLC protocol can be used by
adding "link2" to the ifconfig line in /etc/sysconfig or where ever
ifconfig is run.
At the moment only the X.21 interface is tested. The others may need
tweaks to the clock selection code.
Testing with the high frequency of 20000 Hz (to find problems) only found
the problem that this frequency is too high for slow i386's.
Disable interrupts while setting the timer frequency. This was unnecessary
before rev.1.57 and forgotten in rev.1.57. The critical (i8254) interrupts
are disabled in another way at boot time but not in the sysctl to change
the frequency.
via an ioctl (MOUSE_ACTION).
Fixed a couple of bugs (destructive cursor, uncut, jitter).
Now applications can use the mouse via the MOUSE_MODE ioctl, its
possible to have a signal sent on mouseevents, makeing an event loop
in the application take over mouseevents.
things tend to work better if you write the settings to the correct
register.. (*blush*). This subtle bug has been haunting me for ages, and
will solve a few problems that have been reported to me.
Also, take a shot at fixing the serial BREAK processing, what was there
before never really worked. (There is a PR on this I think)
Real support for a Textmode mousecursor, works by reprogramming the
charset. Together with this support for cut&paste in text mode.
To use it a userland daemon is needed (moused), which provides
the interface to the various mice protokols.
Bug fixes here and there, all known PR's closed by this update.
is only used by the icu support modules and by a few drivers that know
too much about the icu (most only use it to convert `n' to `IRQn'). isa.h
is only used by ioconf.c and by a few drivers that know too much about
isa addresses (a few have to, because config is deficient).
to match (pc98/random_machdep.c probably requires a similar change). This
is a problem area for the PC98 merge - all PC98 ifdefs in <machine/*.h> are
kludges to work around incorrect layering.
Original version by John Hay.
Simplified timestamp code by reading the time exactly when necessary.
This may slow down the interrupt handler with extra calls to microtime(),
but only in bad configurations - the input fifo should normally be
disabled if timestamps on input are being used, since otherwise the
timestamp won't be precisely associated with any particular input event.
The interrupt handler remains slowed down by one test and branch for
each input (and now DCD change) event - avoiding this is not practical
yet.
The simplifications also fixed:
- timestamps for input sometimes being clobbered by output and modem
status interrupts.
- valid timestamps not being available unless the port is configured with
vector siointrts. siointrts no longer exists.
- compiler warnings about siointr* in some configurations.
Simplified timestamp and probe code by depending on recent changes in
microtime() and DELAY() to preserve the interrupt enable flag.
enable flag instead of enable_intr() to restore it to its usual state.
getit() is only called from DELAY() so there is no point in optimising
its speed (this wasn't so clear when it was extern), and using
enable_intr() made it inconvenient to call DELAY() from probes that need
to run with interrupts disabled.
parameters to printf() using the "D" format. (Why this even worked on
my box during testing I don't know, but as soon as I powered it on/off
it quite working.)
using the existing files using the existing PCCARD support. Now that
this is in place I would like to fixup the PCCARD hooks and remove the
if_zp driver. At this point, we support everything we used to support
*AND MORE* with the PCCARD code.
Submitted by: Naoki Hamada <nao@sbl.cl.nec.co.jp> (via the Nomad release)
[ This works on both my 3C589B and 3C589C ]
My 3C509B-COMBO works fine with the following patch. Switching between
UTP and BNC is quite easy. (Just type 'ifconfig ep0 link1 -link2' or 'ifconifg
ep0 link2 -link1'.)
[ I tested this with the additional PC-CARD patches and it works on both
connectors on my 3C589B and 3C589C ]
Reviewed by: nate
Submitted by: Naoki Hamada <nao@sbl.cl.nec.co.jp>
All new code is "#ifdef PC98"ed so this should make no difference to
PC/AT (and its clones) users.
Ok'd by: core
Submitted by: FreeBSD(98) development team
sometimes already been released at the time pcaclose() is called, but
this is now prevented from deadlocking by checking for a running timer
at the start of pca_wait().
At least, i can now play xboing again with pcaudio, this used to hang
the entire system previously within a few seconds.
wdp_fixedcyl) gives it directly. wdp_removedcyl is "reserved" except
in ancient ATA-1 drafts and shouldn't be added. This fixes PR 1288.
Changed some fields and comments in struct wdparams to match a less-
ancient ATA draft.
Fixed bit number for `rdy' in status string.
gcc only inlines memcpy()'s whose count is constant and didn't inline
these. I want memcpy() in the kernel go away so that it's obvious that
it doesn't need to be optimized. Now it is only used for one struct
copy in si.c.
ansi and traditional cpp.
The nesting rules of macros are different, which required some changes.
Use __CONCAT(x,y) instead of /**/.
Redo some comments to use /* */ rather than "# comment" because the ansi
cpp cares about those, and also cares about quote matching.
on the baud rate, dont get upset if it's been hung up by setting B0.
Instead, sleep for a short time, as the host controller takes a while
to go through the state changes.
