protection change.
On superpage promotion, x86 pmaps do not invalidate existing 4K
entries for the superpage range, because they are compatible with the
promoted 2/4M entry. But the invalidation on superpage removal or
protection change only did single INVLPG with the base address of the
superpage. This reliably flushed superpage TLB entry, and 4K entry
for the first page of the superpage, potentially leaving other 4K TLB
entries lingering. Do the invalidation of the whole superpage range
to correct the problem.
Note that the precise invalidation is done by x86 code for kernel_pmap
only, for user pmaps whole (per-AS) TLB is flushed. This made the bug
well hidden, because promotions of the kernel mappings require
specific load.
Reported and tested by: Jonathan Looney <jtl@netflix.com> (previous version)
Reviewed by: alc
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
in the i386 pmap.
The curcpu macro loads the per-cpu data pointer as its first step,
so the remaining steps of pcpu_find(curcpu) are circular.
get_pcpu() is already implemented for arm, arm64, and risc-v.
My plan is to implement it for the remaining architectures and use
it to replace several instances of pcpu_find(curcpu) in MI code.
Reviewed by: kib
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D9370
SDM states that CLFLUSHOPT instructions can be ordered with other
writes by SFENCE, heavier MFENCE is not required.
Reviewed by: alc
Sponsored by: The FreeBSD Foundation
MFC after: 2 weeks
the cmap lock. Releasing the lock first may result in the thread
being immediately rescheduled and bound to the same CPU, only to
unpin itself upon resuming execution.
Noted by: skra (in review for armv6 equivalent)
MFC after: 1 week
We would previously invalidate such entries individually, resulting in more
IPIs than necessary.
Reviewed by: alc, kib
MFC after: 3 weeks
Differential Revision: https://reviews.freebsd.org/D9094
- em(4) igb(4) and lem(4)
- deprecate the igb device from kernel configurations
- create a symbolic link in /boot/kernel from if_em.ko to if_igb.ko
Devices tested:
- 82574L
- I218-LM
- 82546GB
- 82579LM
- I350
- I217
Please report problems to freebsd-net@freebsd.org
Partial review from jhb and suggestions on how to *not* brick folks who
originally would have lost their igbX device.
Submitted by: mmacy@nextbsd.org
MFC after: 2 weeks
Relnotes: yes
Sponsored by: Limelight Networks and Dell EMC Isilon
Differential Revision: https://reviews.freebsd.org/D8299
Right now size of the structure is 472 bytes on amd64, which is
already large and stack allocations are indesirable. With the ino64
work, MNAMELEN is increased to 1024, which will make it impossible to have
struct statfs on the stack.
Extracted from: ino64 work by gleb
Discussed with: mckusick
Tested by: pho
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
operations to the MD PCPU region. Change sysmap initialization to only
allocate KVA pages for CPUs that are actually present. As a minor
optimization, this also prevents false sharing between adjacent sysmap objects
since the pcpu struct is already cacheline-aligned.
While here, move pc_qmap_addr initialization for the BSP into
pmap_bootstrap(), which allows use of pmap_quick* functions during early boot.
Reviewed by: kib
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D8833
Changes include modifications in kernel crash dump routines, dumpon(8) and
savecore(8). A new tool called decryptcore(8) was added.
A new DIOCSKERNELDUMP I/O control was added to send a kernel crash dump
configuration in the diocskerneldump_arg structure to the kernel.
The old DIOCSKERNELDUMP I/O control was renamed to DIOCSKERNELDUMP_FREEBSD11 for
backward ABI compatibility.
dumpon(8) generates an one-time random symmetric key and encrypts it using
an RSA public key in capability mode. Currently only AES-256-CBC is supported
but EKCD was designed to implement support for other algorithms in the future.
The public key is chosen using the -k flag. The dumpon rc(8) script can do this
automatically during startup using the dumppubkey rc.conf(5) variable. Once the
keys are calculated dumpon sends them to the kernel via DIOCSKERNELDUMP I/O
control.
When the kernel receives the DIOCSKERNELDUMP I/O control it generates a random
IV and sets up the key schedule for the specified algorithm. Each time the
kernel tries to write a crash dump to the dump device, the IV is replaced by
a SHA-256 hash of the previous value. This is intended to make a possible
differential cryptanalysis harder since it is possible to write multiple crash
dumps without reboot by repeating the following commands:
# sysctl debug.kdb.enter=1
db> call doadump(0)
db> continue
# savecore
A kernel dump key consists of an algorithm identifier, an IV and an encrypted
symmetric key. The kernel dump key size is included in a kernel dump header.
The size is an unsigned 32-bit integer and it is aligned to a block size.
The header structure has 512 bytes to match the block size so it was required to
make a panic string 4 bytes shorter to add a new field to the header structure.
If the kernel dump key size in the header is nonzero it is assumed that the
kernel dump key is placed after the first header on the dump device and the core
dump is encrypted.
Separate functions were implemented to write the kernel dump header and the
kernel dump key as they need to be unencrypted. The dump_write function encrypts
data if the kernel was compiled with the EKCD option. Encrypted kernel textdumps
are not supported due to the way they are constructed which makes it impossible
to use the CBC mode for encryption. It should be also noted that textdumps don't
contain sensitive data by design as a user decides what information should be
dumped.
savecore(8) writes the kernel dump key to a key.# file if its size in the header
is nonzero. # is the number of the current core dump.
decryptcore(8) decrypts the core dump using a private RSA key and the kernel
dump key. This is performed by a child process in capability mode.
If the decryption was not successful the parent process removes a partially
decrypted core dump.
Description on how to encrypt crash dumps was added to the decryptcore(8),
dumpon(8), rc.conf(5) and savecore(8) manual pages.
EKCD was tested on amd64 using bhyve and i386, mipsel and sparc64 using QEMU.
The feature still has to be tested on arm and arm64 as it wasn't possible to run
FreeBSD due to the problems with QEMU emulation and lack of hardware.
Designed by: def, pjd
Reviewed by: cem, oshogbo, pjd
Partial review: delphij, emaste, jhb, kib
Approved by: pjd (mentor)
Differential Revision: https://reviews.freebsd.org/D4712
contain a vm_page_t at the specified index. However, with this
change, vm_radix_remove() no longer panics. Instead, it returns NULL
if there is no vm_page_t at the specified index. Otherwise, it
returns the vm_page_t. The motivation for this change is that it
simplifies the use of radix tries in the amd64, arm64, and i386 pmap
implementations. Instead of performing a lookup before every remove,
the pmap can simply perform the remove.
Reviewed by: kib, markj
Differential Revision: https://reviews.freebsd.org/D8708
- If a page fault is triggered due to reserved bits in a PTE, treat it
as a fatal fault and panic.
- If PG_NX is in use, report whether a fatal page fault is due to an
instruction fetch or a data access.
- If a fatal page fault is due to reserved bits in a PTE, report that as
the page fault type rather than a protection violation.
MFC after: 1 month
The userspace case was already handled by pmap_allocpte(). For kernel
VA, page table page must exist, and demote cannot fail, so we need to
just call pmap_demote_pde(). Also note that due to the machine AS
layout, promotions in the KVA on i386 are highly unlikely, so this
change is mostly for completeness.
Reviewed by: alc, markj
Tested by: pho
Sponsored by: The FreeBSD Foundation
MFC after: 2 weeks
Differential revision: https://reviews.freebsd.org/D8323
Reject attempts to read from or memory map offsets in /dev/mem that are
beyond the maximum-supported physical address of the current CPU.
Reviewed by: kib
MFC after: 1 month
Differential Revision: https://reviews.freebsd.org/D7408
EFER_NXE is set in the EFER MSR by initializecpu() and must be set on all
CPUs in the system. When PG_NX support was added to PAE on i386, the
block to enable EFER_NXE was placed in a section of initializecpu() that
only runs if 'cpu == CPU_686'. During early boot, locore does an
initial pass to set cpu that sets it to CPU_686 on all CPUs later than
a Pentium. Later, printcpuinfo() adjusts the 'cpu' variable on
PII and later CPUs to one of CPU_PII, CPU_PIII, or CPU_P4. However,
printcpuinfo() is called after initializecpu() on the BSP, so the BSP
would enable EFER_NXE and pg_nx. The APs execute initializecpu() much
later after printcpuinfo() has run. The end result on a modern CPU was
that cpu was set to CPU_PIII when the APs invoked initializecpu(), so
they did not enable EFER_NXE. As a result, the APs would fault when
trying to access any pages marked with PG_NX set.
When booting a 2 CPU PAE kernel in bhyve this manifested as a hang before
single user mode. The attempt to execute /bin/init tried to copy out
the exec strings (argv, etc.) to a non-executable mapping while running
on the AP. The instruction kept faulting due to invalid bits in the PTE
in an infinite loop.
Fix this by moving the code to enable EFER_NXE out of the switch statement
on 'cpu' and always doing it if 'amd_feature' supports AMDID_NX.
MFC after: 2 weeks
- Make !KDB config buildable.
- Simplify interface to nmi_handle_intr() by evaluating panic_on_nmi
in one place, namely nmi_call_kdb(). This allows to remove do_panic
argument from the functions, and to remove i386/amd64 duplication of
the variable and sysctl definitions. Note that now NMI causes
panic(9) instead of trap_fatal() reporting and then panic(9),
consistently for NMIs delivered while CPU operated in ring 0 and 3.
Sponsored by: The FreeBSD Foundation
MFC after: 2 weeks
On several Intel chipsets, diagnostic NMIs sent from BMC or NMIs
reporting hardware errors are broadcasted to all CPUs.
When kernel is configured to enter kdb on NMI, the outcome is
problematic, because each CPU tries to enter kdb. All CPUs are
executing NMI handlers, which set the latches disabling the nested NMI
delivery; this means that stop_cpus_hard(), used by kdb_enter() to
stop other cpus by broadcasting IPI_STOP_HARD NMI, cannot work. One
indication of this is the harmless but annoying diagnostic "timeout
stopping cpus".
Much more harming behaviour is that because all CPUs try to enter kdb,
and if ddb is used as debugger, all CPUs issue prompt on console and
race for the input, not to mention the simultaneous use of the ddb
shared state.
Try to fix this by introducing a pseudo-lock for simultaneous attempts
to handle NMIs. If one core happens to enter NMI trap handler, other
cores see it and simulate reception of the IPI_STOP_HARD. More,
generic_stop_cpus() avoids sending IPI_STOP_HARD and avoids waiting
for the acknowledgement, relying on the nmi handler on other cores
suspending and then restarting the CPU.
Since it is impossible to detect at runtime whether some stray NMI is
broadcast or unicast, add a knob for administrator (really developer)
to configure debugging NMI handling mode.
The updated patch was debugged with the help from Andrey Gapon (avg)
and discussed with him.
Sponsored by: The FreeBSD Foundation
MFC after: 2 weeks
Differential revision: https://reviews.freebsd.org/D8249
These two ALU instructions first appeared on Linux. Then, libpcap adopted
and made them available since 1.6.2. Now more platforms including NetBSD
have them in kernel. So do we.
--이 줄 이하는 자동으로 제거됩니다--
Using the device pager with /dev/kmem is not stable since KVA mappings
are transient, but the device pager caches the PA associated with a
given offset forever. Interestingly, mips' implementation of
memmap() already refused requests for /dev/kmem.
Note that kvm_read/kvm_write do not use mmap, but use read and write on
/dev/kmem, so this should not affect libkvm users.
Reviewed by: kib
MFC after: 2 months
with no creative content. Include "lost" changes from git:
o Use /dev/efi instead of /dev/efidev
o Remove redundant NULL checks.
Submitted by: kib@, dim@, zbb@, emaste@
to add actions that run when a TCP frame is sent or received on a TCP
session in the ESTABLISHED state. In the base tree, this functionality is
only used for the h_ertt module, which is used by the cc_cdg, cc_chd, cc_hd,
and cc_vegas congestion control modules.
Presently, we incur overhead to check for hooks each time a TCP frame is
sent or received on an ESTABLISHED TCP session.
This change adds a new compile-time option (TCP_HHOOK) to determine whether
to include the hhook(9) framework for TCP. To retain backwards
compatibility, I added the TCP_HHOOK option to every configuration file that
already defined "options INET". (Therefore, this patch introduces no
functional change. In order to see a functional difference, you need to
compile a custom kernel without the TCP_HHOOK option.) This change will
allow users to easily exclude this functionality from their kernel, should
they wish to do so.
Note that any users who use a custom kernel configuration and use one of the
congestion control modules listed above will need to add the TCP_HHOOK
option to their kernel configuration.
Reviewed by: rrs, lstewart, hiren (previous version), sjg (makefiles only)
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D8185
userland. It supports userland interfaces to UEFI Runtime Services. This is
indended to the the MI portion of EFI RuntimeServices support.
Differential Revision: https://reviews.freebsd.org/D8128
Reviewed by: kib@, wblock@, Ganael Laplanche
Reduce the cost of TLB invalidation on x86 by using per-CPU completion flags
Reduce contention during TLB invalidation operations by using a per-CPU
completion flag, rather than a single atomically-updated variable.
On a Westmere system (2 sockets x 4 cores x 1 threads), dtrace measurements
show that smp_tlb_shootdown is about 50% faster with this patch; observations
with VTune show that the percentage of time spent in invlrng_single_page on an
interrupt (actually doing invalidation, rather than synchronization) increases
from 31% with the old mechanism to 71% with the new one. (Running a basic file
server workload.)
Submitted by: Anton Rang <rang at acm.org>
Reviewed by: cem (earlier version)
Sponsored by: Dell EMC Isilon
Differential Revision: https://reviews.freebsd.org/D8041
like other PCI network drivers. The sys/ofed directory is now mainly
reserved for generic infiniband code, with exception of the mthca driver.
- Add new manual page, mlx4en(4), describing how to configure and load
mlx4en.
- All relevant driver C-files are now prefixed mlx4, mlx4_en and
mlx4_ib respectivly to avoid object filename collisions when compiling
the kernel. This also fixes an issue with proper dependency file
generation for the C-files in question.
- Device mlxen is now device mlx4en and depends on device mlx4, see
mlx4en(4). Only the network device name remains unchanged.
- The mlx4 and mlx4en modules are now built by default on i386 and
amd64 targets. Only building the mlx4ib module depends on
WITH_OFED=YES .
Sponsored by: Mellanox Technologies
(1) Print the default segment %ss before adresses relative to %bp.
This is too cluttered for me, but so is printing some other default
prefixes, and this is a reasonable reminder that %ss is quite
likely to be different from %ds in 16-bit mode.
db_disasm still handles prefixes poorly, by trying to discard
redundant ones. This loses information, and sometimes the result
is wrong or misleading.
Clean up nearby initializations and dead code.
(2) Fix decoding of operand and address size prefixes in 16-bit mode.
They reverse the default in all modes.
Obtained from: (1) is partly from r1.4 (2003/11/08) in DFlyBSD (?)
db_segsize().
Use db_segsize() to set the default operand/address size for
disassembling. Allow overriding this with the "alternate" display
format /I. The API of db_disasm() should be debooleanized to pass a
more general request (amd64 needs overrides to sizes of 16, 32, and
64, but this commit doesn't implement anything for amd64 since much
larger changes are needed to restore the amd64 disassmbler's support
for non-default sizes).
Fix db_print_loc_and_inst() to ask for the normal format and not the
alternate in normal operation.
This is most useful for vm86 mode, but also works for 16-bit protected
mode.
Use db_segsize() to avoid trying to print a garbage stack trace if %cs
is 16 bits. Print something like the stack trace termination message
for a trap boundary instead.
Document that the alternate format is now useful on i386.
early printfs and debugging of vm86 initialization and some other early
initialization in some cases.) Add an option debug.late_console (with
default 1=off) to move console and kdb initialization back where it was.
Do the same for amd64 although there is no vm86 there.
On my test system, debug.late_console=0 works for the syscons, sio and
uart console drivers on amd64 and i386, and for vt on i386 but not on
amd64.
The early printfs fixed by debug.late_console=0 are:
- on i386, the message about lost memory above 4G
- with -v in otherwise normal use, about 20 printfs for SMAP
- other debugging messages for memory sizing. Mostly under -v and
not printed in normal use.
Document in a comment how much earlier the initialization and early
printf()s can be. That is very early for the console. Not much more
than curthread is needed. kdb use obviously needs to be not so early,
since it needs IDT initialization and that is done relatively late
for convenience and historical reasons.
preserve the ABI and API for applications. It was removed in the port
to amd64, but was remained as garbage giving a micro-pessimization and
spurious single-step traps on i386.
pcb_psl was intended to be used just to do a context switch of PSL_I,
but this context switch was null in most or all versions, and
mis-switching of PSL_T was done instead.
Some history:
- in 386BSD-0.0, cpu_switch() ran at splhigh() and splhigh() did too
much interrupt disabling, so interrupts were hard-disabled across
cpu_switch() and too many other places
- in 386BSD-0.0-patchkit through FreeBSD-4 and FreeBSD-5 before
SMPng, splhigh() did soft interrupt masking, and cpu_switch() was
excessively cautious and did a cli at the start and a sti at the
end to hard-disable interrupts across the switch
- SMPng replaced the spl's and cli's by spinlocks (just sched_lock?),
so interrupts were hard-disabled across cpu_switch() and too many
other places again
- initial attempts to fix this intended to restore some soft
interrupt disabling, but to support variations in this cpu_switch()
used pushfl/popfl into pcb_psl to avoid hard-coding the assumption
that the initial and final states have PSL_I enabled. But the
version with soft interrupt disabling wasn't used for long, or was
never committed, (except I always used my different version of it
for UP) so the pushfl/popl and pcb_psl to hold them have been doing
less than nothing for about 14 years.
While here, avoid using the old variable 'code' and remove it
in trap(). ('code' was meant for holding things like %dr6,
but is too small to hold %dr6 on amd64 and was reduced to an
obfuscation of tf_err, with early truncation on amd64.)
Submitted by: Michael Butler (imb@...)
This is not very easy to do, since ddb didn't know when traps are
for single-stepping. It more or less assumed that traps are either
breakpoints or single-step, but even for x86 this became inadequate
with the release of the i386 in ~1986, and FreeBSD passes it other
trap types for NMIs and panics.
On x86, teach ddb when a trap is for single stepping using the %dr6
register. Unknown traps are now treated almost the same as breakpoints
instead of as the same as single-steps. Previously, the classification
of breakpoints was almost correct and everything else was unknown so
had to be treated as a single-step. Now the classification of single-
steps is precise, the classification of breakpoints is almost correct
(as before) and everything else is unknown and treated like a
breakpoint.
This fixes:
- breakpoints not set by ddb, including the main one in kdb_enter(),
were treated as single-steps and not stopped on when stepping
(except for the usual, simple case of a step with residual count 1).
As special cases, kdb_enter() didn't stop for fatal traps or panics
- similarly for "hardware breakpoints".
Use a new MD macro IS_SSTEP_TRAP(type, code) to code to classify
single-steps. This is excessively complicated for bug-for-bug and
backwards compatibilty. Design errors apparently started in Mach
in ~1990 or perhaps in the FreeBSD interface in ~1993. Common trap
types like single steps should have a unique MI code (like the TRAP*
codes for user SIGTRAP) so that debuggers don't need macros like
IS_SSTEP_TRAP() to decode them. But 'type' is actually an ambiguous
MD trap number, and code was always 0 (now it is (int)%dr6 on x86).
So it was impossible to determine the trap type from the args.
Global variables had to be used.
There is already a classification macro db_pc_is_single_step(), but
this just gets in the way. It is only used to recover from bugs in
IS_BREAKPOINT_TRAP(). On some arches, IS_BREAKPOINT_TRAP() just
duplicates the ambiguity in 'type' and misclassifies single-steps as
breakpoints. It defaults to 'false', which is the opposite of what is
needed for bug-for-bug compatibility.
When this is cleaned up, MI classification bits should be passed in
'code'. This could be done now for positive-logic bits, since 'code'
was always 0, but some negative logic is needed for compatibility so
a simple MI classificition is not usable yet.
After reading %dr6, clear the single-step bit in it so that the type
of the next debugger trap can be decoded. This is a little
ddb-specific. ddb doesn't understand the need to clear this bit and
doing it before calling kdb is easiest. gdb would need to reverse
this to support hardware breakpoints, but it just doesn't support
them now since gdbstub doesn't support %dr*.
Fix a bug involving %dr6: when emulating a single-step trap for vm86,
set the bit for it in %dr6. Userland debuggers need this. ddb now
needs this for vm86 bios calls. The bit gets copied to 'code' then
cleared again.
Fix related style bugs:
- when clearing bits for hardware breakpoints in %dr6, spell the mask
as ~0xf on both amd64 and i386 to get the correct number of bits
using sign extension and not need a comment about using the wrong
mask on amd64 (amd64 traps for invalid results but clearing the
reserved top bits didn't trap since they are 0).
- rewrite my old wrong comments about using %dr6 for ddb watchpoints.
The 'cpu' and 'cpu_class' variables were always set to the same value
on amd64 and are legacy holdovers from i386. Remove them entirely on
amd64.
Reviewed by: imp, kib (older version)
Differential Revision: https://reviews.freebsd.org/D7888
SEL_UPL and sometimes PSL_VM. This is just a style change on amd64,
but on i386 it fixes 1 unimportant place where the PSL_VM check was
missing and starts fixing 1 important place where the PSL_VM check
had a logic error.
Fix logic errors in treating vm86 bioscall mode as kernel mode. The
main place checked all the necessary flags, but put the necessary
parentheses for the PSL_VM and PCB_VM86CALL checks in the wrong
place. The broken case is only reached if a vm86 bioscall uses a
%cs which is nonzero mod 4, but that is unusual -- most bios calls
start with %cs = 0xc000 or 0xf000 and rarely change it. Another
place was missing the check for PCB_VM86CALL, but was only reachable
if there are bugs virtualizing PSL_I.
Add a macro TF_HAS_STACKREGS() and use this instead of converting
open-coded checks of SEL_UPL, etc. to TRAPF_USERMODE() when we only
care about whether the frame has stack registers. This fixes 3
places in my recent fix for register variables in vm86 mode where I
messed up the PSL_VM check and cleans up other places.
Move PMAP_TS_REFERENCED_MAX out of the various pmap implementations and
into vm/pmap.h, and describe what its purpose is. Eliminate the archaic
"XXX" comment about its value. I don't believe that its exact value, e.g.,
5 versus 6, matters.
Update the arm64 and riscv pmap implementations of pmap_ts_referenced()
to opportunistically update the page's dirty field.
On amd64, use the PDE value already cached in a local variable rather than
dereferencing a pointer again and again.
Reviewed by: kib, markj
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D7836
In vm86.c, fix 2 (rarely used) cases where the return code lost the
single-step indicator. While here, fix 2 misspellings of PSL_T as
PSL_TF (TF is the CPU manufacturer's spelling, but we use T).
In trap.c, turn T_PROTFLT and T_STKFLT into T_TRCTRAP if
vm86_emulate() asked for this (it does this when the instruction is
being traced and was successully emulated). In the kernel case, we
used to deliver the trap as SIGTRAP to the process, where it always
terminated the process; now we deliver the trap as T_TRCTRAP to kdb,
where it normally gives single-stepping. In the user case, the only
difference is that we now clear PSL_T and initialize ucode properly.
Reviewed by: kib
Idle page zeroing has been disabled by default on all architectures since
r170816 and has some bugs that make it seemingly unusable. Specifically,
the idle-priority pagezero thread exacerbates contention for the free page
lock, and yields the CPU without releasing it in non-preemptive kernels. The
pagezero thread also does not behave correctly when superpage reservations
are enabled: its target is a function of v_free_count, which includes
reserved-but-free pages, but it is only able to zero pages belonging to the
physical memory allocator.
Reviewed by: alc, imp, kib
Differential Revision: https://reviews.freebsd.org/D7714
dependent pmap_ts_referenced() so that it updates the page's dirty field
if a modified bit is found while counting reference bits. This
opportunistic update can be performed at low cost and can eliminate the
need for some future calls to pmap_is_modified() by the machine-
independent layer.
Reviewed by: kib, markj
MFC after: 3 weeks
Sponsored by: EMC / Isilon Storage Division
Differential Revision: https://reviews.freebsd.org/D7722
for zeroing pages in idle where nontemporal writes are clearly best.
This is almost a no-op since zeroing in idle works does nothing good
and is off by default. Fix END() statement forgotten in previous
commit.
Align the loop in sse2_pagezero(). Since it writes to main memory,
the loop doesn't have to be very carefully written to keep up.
Unrolling it was considered useless or harmful and was not done on
i386, but that was too careless.
Timing for i386: the loop was not unrolled at all, and moved only 4
bytes/iteration. So on a 2GHz CPU, it needed to run at 2 cycles/
iteration to keep up with a memory speed of just 4GB/sec. But when
it crossed a 16-byte boundary, on old CPUs it ran at 3 cycles/
iteration so it gave a maximum speed of 2.67GB/sec and couldn't even
keep up with PC3200 memory. Fix the alignment so that it keep up with
4GB/sec memory, and unroll once to get nearer to 8GB/sec. Further
unrolling might be useless or harmful since it would prevent the loop
fitting in 16-bytes. My test system with an old CPU and old DDR1 only
needed 5+ GB/sec. My test system with a new CPU and DDR3 doesn't need
any changes to keep up ~16GB/sec.
Timing for amd64: with 8-byte accesses and newer faster CPUs it is
easy to reach 16GB/sec but not so easy to go much faster. The
alignment doesn't matter much if the CPU is not very old. The loop
was already unrolled 4 times, but needs 32 bytes and uses a fancy
method that doesn't work for 2-way unrolling in 16 bytes. Just
align it to 32-bytes.
Early use of vm86 depends on the PIC being reset to mask interrupts,
but r286667 moved PIC initialization to after where vm86 may be first
used.
Move the PIC initialization up to immdiately before vm86 initialization.
All invocations of diff that I tried display this move poorly so that it
looks like PIC and vm86 initialization was moved later.
r286667 was to move console initialization later. The diffs are again
unreadable -- they show a large move that doesn't seem to involve the
console. The PIC initialization stayed just below the console
initialization where it could still be debugged but no longer works.
Later console initialization breaks mainly debugging vm86 initialization
and memory sizing using ddb and printf(). There are several printf()s
in the memory sizing that now go nowhere since message buffer
initialization has always been too late. Memory sizing is done by loader
for most users, but the lost messages for this case are even more
interesting than for an auto-probe since they tell you what the loader
found.
vm86 uses the tss, but r273995 moved tss initialization to after where
it may be first used, just because tss_esp0 now depends on later
initializations and/or amd64 does it later.
vm86 is first used for memory sizing in cases where the loader can't
figure out the size or is not used. Its initialization is placed
immediately before memory sizing to support this, and the tss was
initialized a little earlier.
Move everything in the tss initialization except for tss_esp0 back to
almost where it was, immediately before vm86 initialization (the
combined move is from before dblflt_tss initialization to after). Add
only early initialization of tss_esp0, later reloading of the tss, and
comments. The initial tss_esp0 no longer has space for the pcb since
initially the size of the pcb is not known and no pcb is needed.
(Later changes broke debugging at this point, so the nonexistent pcb
cannot be used by debuggers, and at the time of 273995 when ddb was
almost able to debug this problem it didn't need the pcb.) The
iniitial tss_esp0 still has a magic 16 bytes reserved for vm86
although I think this is unused too.
In all of these source files, the userspace pointer size corresponds
with the kernelspace pointer size, meaning that casting directly works.
As I'm planning on making 32-bit execution on 64-bit systems work as
well, use TO_PTR() here as well, so that the changes between source
files remain minimal.
Move msix_disable_migration under #ifdef SMP since it doesn't make sense
for !SMP kernels.
PR: 212014
Reported by: Glyn Grinstead <glyn@grinstead.org>
MFC after: 3 days
Copy over amd64's cloudabi64_sysvec.c into i386 and tailor it to work.
Again, we use a system call convention similar to FreeBSD, except that
there is no support for indirect system calls (%eax == 0).
Where i386 differs from amd64 is that we have to store thread/process
entry arguments on the stack instead of using registers. We also have to
put an extra pointer on the stack for TLS (for GSBASE). Place that
pointer in the empty slot that is normally used to hold return
addresses. That seems to keep the code simple.
Reviewed by: kib
Differential Revision: https://reviews.freebsd.org/D7590
This driver only supports 10Mb Ethernet using PIO (the hardware supports
DMA, but the driver only does PIO). There are not any PCCard adapters
supported by this driver, only ISA cards. In addition, it does not use
bus_space but instead uses bcopy with volatile pointers triggering a
host of warnings. (if_ie.c is one of 3 files always built with
-Wno-error)
Relnotes: yes
This hardware is not present on any modern systems. The driver is quite
hackish (raw inb/outb instead of bus_space, and raw inb/outb to random
I/O ports to enable ACPI since it predated proper ACPI support).
Relnotes: yes
The wl(4) driver supports pre-802.11 PCCard wireless adapters that
are slower than 802.11b. They do not work with any of the 802.11
framework and the driver hasn't been reported to actually work in a
long time.
Relnotes: yes
The si(4) driver supported multiport serial adapters for ISA, EISA, and
PCI buses. This driver does not use bus_space, instead it depends on
direct use of the pointer returned by rman_get_virtual(). It is also
still locked by Giant and calls for patch testing to convert it to use
bus_space were unanswered.
Relnotes: yes
Fix PC_REGS() so that printing of instructions works in some useful
cases. ddb only understands a single flat address space, but this
macro allows mapping $cs:$eip into vm86's flat address space well
enough for the MI parts of ddb. This doesn't work for the MD parts
that do stack traces, and there are no similar macros for data addresses.
PC_REGS() has to use the trapframe pointer instead of the pcb for this.
For other CPUs, the trapframe pointer is not available except by tracing
back to it. But tracing back through vm86 trapframes is broken even
starting with one.
exception is caught in kernel mode. There are third-party modules
which trigger the issue, and since the problem causes usermode state
corruption at least, panic in production kernels as well.
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
difference between files.
For pc98, put x86/mp_x86.c into the same place as used by i386 file list.
Fix typo in comment.
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
Any sensible workflow will include a revision control system from which
to restore the old files if required. In normal usage, developers just
have to clean up the mess.
Reviewed by: jhb
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D7353
Set vm_guest to a new enum value (VM_GUEST_KVM) when kvm is detected and use
vm_guest in conditionals testing for KVM.
Also, fix a conditional checking if we're running in a VM which caught only
the generic VM case, but not more specific VMs (KVM, VMWare, etc.). (Spotted
by: vangyzen).
Differential revision: https://reviews.freebsd.org/D7172
Sponsored by: Dell Inc.
Approved by: kib (mentor), vangyzen (mentor)
Reviewed by: alc
MFC after: 4 weeks
If the hypervisor version is smaller than 4.6.0. Xen commits 74fd00 and
70a3cb are required on the hypervisor side for this to be fixed, and those
are only included in 4.6.0, so stay on the safe side and disable MSI-X
interrupt migration on anything older than 4.6.0.
It should not cause major performance degradation unless a lot of MSI-X
interrupts are allocated.
Sponsored by: Citrix Systems R&D
MFC after: 3 days
Reviewed by: jhb
Differential revision: https://reviews.freebsd.org/D7148
If tf_trapno contains garbage which appears to be equal to T_NMI,
e.g. due to thread previously entered kernel due to NMI, doreti
sequence skips ast, and does so until a trap or hardware interrupt
occur.
The visible effects of the issue are quite confusing. First, signals
delivery is postponed in observable ways. In particular, the
guarantee that unblocked async signals queue is flushed before a
return from syscall, is broken. Second, if there are pending signals,
all interruptible sleeps of the stuck thread are aborted immediately.
Since modern CPUs are relatively fast and tickless kernel generates
low interrupt rate, the faulty condition might exist for long time (in
an application time scale).
In collaboration with: pho
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
FreeBSD support NX bit on X86_64 processors out of the box, for i386 emulation
use READ_IMPLIES_EXEC flag, introduced in r302515.
While here move common part of mmap() and mprotect() code to the files in compat/linux
to reduce code dupcliation between Linuxulator's.
Reported by: Johannes Jost Meixner, Shawn Webb
MFC after: 1 week
XMFC with: r302515, r302516
In Linux if this flag is set, PROT_READ implies PROT_EXEC for mmap().
Linux/i386 set this flag automatically if the binary requires executable stack.
READ_IMPLIES_EXEC flag will be used in the next Linux mmap() commit.
mp_maxid or CPU_FOREACH() as appropriate. This fixes a number of places in
the kernel that assumed CPU IDs are dense in [0, mp_ncpus) and would try,
for example, to run tasks on CPUs that did not exist or to allocate too
few buffers on systems with sparse CPU IDs in which there are holes in the
range and mp_maxid > mp_ncpus. Such circumstances generally occur on
systems with SMT, but on which SMT is disabled. This patch restores system
operation at least on POWER8 systems configured in this way.
There are a number of other places in the kernel with potential problems
in these situations, but where sparse CPU IDs are not currently known
to occur, mostly in the ARM machine-dependent code. These will be fixed
in a follow-up commit after the stable/11 branch.
PR: kern/210106
Reviewed by: jhb
Approved by: re (glebius)
threads, to make it less confusing and using modern kernel terms.
Rename the functions to reflect current use of the functions, instead
of the historic KSE conventions:
cpu_set_fork_handler -> cpu_fork_kthread_handler (for kthreads)
cpu_set_upcall -> cpu_copy_thread (for forks)
cpu_set_upcall_kse -> cpu_set_upcall (for new threads creation)
Reviewed by: jhb (previous version)
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
Approved by: re (hrs)
Differential revision: https://reviews.freebsd.org/D6731
bus_get_cpus() returns a specified set of CPUs for a device. It accepts
an enum for the second parameter that indicates the type of cpuset to
request. Currently two valus are supported:
- LOCAL_CPUS (on x86 this returns all the CPUs in the package closest to
the device when DEVICE_NUMA is enabled)
- INTR_CPUS (like LOCAL_CPUS but only returns 1 SMT thread for each core)
For systems that do not support NUMA (or if it is not enabled in the kernel
config), LOCAL_CPUS fails with EINVAL. INTR_CPUS is mapped to 'all_cpus'
by default. The idea is that INTR_CPUS should always return a valid set.
Device drivers which want to use per-CPU interrupts should start using
INTR_CPUS instead of simply assigning interrupts to all available CPUs.
In the future we may wish to add tunables to control the policy of
INTR_CPUS (e.g. should it be local-only or global, should it ignore
SMT threads or not).
The x86 nexus driver exposes the internal set of interrupt CPUs from the
the x86 interrupt code via INTR_CPUS.
The ACPI bus driver and PCI bridge drivers use _PXM to return a suitable
LOCAL_CPUS set when _PXM exists and DEVICE_NUMA is enabled. They also and
the global INTR_CPUS set from the nexus driver with the per-domain set from
_PXM to generate a local INTR_CPUS set for child devices.
Compared to the r298933, this version uses 'struct _cpuset' in
<sys/bus.h> instead of 'cpuset_t' to avoid requiring <sys/param.h>
(<sys/_cpuset.h> still requires <sys/param.h> for MAXCPU even though
<sys/_bitset.h> does not after recent changes).
PCI-express HotPlug support is implemented via bits in the slot
registers of the PCI-express capability of the downstream port along
with an interrupt that triggers when bits in the slot status register
change.
This is implemented for FreeBSD by adding HotPlug support to the
PCI-PCI bridge driver which attaches to the virtual PCI-PCI bridges
representing downstream ports on HotPlug slots. The PCI-PCI bridge
driver registers an interrupt handler to receive HotPlug events. It
also uses the slot registers to determine the current HotPlug state
and drive an internal HotPlug state machine. For simplicty of
implementation, the PCI-PCI bridge device detaches and deletes the
child PCI device when a card is removed from a slot and creates and
attaches a PCI child device when a card is inserted into the slot.
The PCI-PCI bridge driver provides a bus_child_present which claims
that child devices are present on HotPlug-capable slots only when a
card is inserted. Rather than requiring a timeout in the RC for
config accesses to not-present children, the pcib_read/write_config
methods fail all requests when a card is not present (or not yet
ready).
These changes include support for various optional HotPlug
capabilities such as a power controller, mechanical latch,
electro-mechanical interlock, indicators, and an attention button.
It also includes support for devices which require waiting for
command completion events before initiating a subsequent HotPlug
command. However, it has only been tested on ExpressCard systems
which support surprise removal and have none of these optional
capabilities.
PCI-express HotPlug support is conditional on the PCI_HP option
which is enabled by default on arm64, x86, and powerpc.
Reviewed by: adrian, imp, vangyzen (older versions)
Relnotes: yes
Differential Revision: https://reviews.freebsd.org/D6136
Not sure why the platform hypercall was disabled on i386, just enable it in
order to fix compilation of the PV timer on i386.
Sponsored by: Citrix Systems R&D
driver is (or behaves identically to) /dev/mem. Remove the D_MEM flag
from random drivers.
Note that currently the D_MEM flag does not affect any behaviour, but
this going to change in the next commit.
Noted and reviewed by: alc
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
X-Differential revision: https://reviews.freebsd.org/D6149
rounddown2 tends to produce longer lines than the original code
and when the code has a high indentation level it was not really
advantageous to do the replacement.
This tries to strike a balance between readability using the macros
and flexibility of having the expressions, so not everything is
converted.
Submitted by: Jun Su <junsu microsoft com>
Reviewed by: jhb, kib, sephe
Sponsored by: Microsoft OSTC
Differential Revision: https://reviews.freebsd.org/D5910
doreti provides the common code path for returning from interrupt
andlers on x86. Exposing doreti as a global symbol allows kernel
modules to include low-level interrupt handlers instead of requiring
all low-level handlers to be statically compiled into the kernel.
Submitted by: Howard Su <howard0su@gmail.com>
Reviewed by: kib
Some BIOSes disable AMD Topology extension on AMD Family 15h notebook
processors. We re-enable the extension, so that we can properly discover
core and cache topology. Linux seems to do the same.
Reported by: Johannes Dieterich <dieterich.joh@gmail.com>
Reviewed by: jhb, kib
Tested by: Johannes Dieterich <dieterich.joh@gmail.com>
(earlier version)
MFC after: 3 weeks
Differential Revision: https://reviews.freebsd.org/D5883
kern.features.linux: 1 meaning linux 32 bits binaries are supported
kern.features.linux64: 1 meaning linux 64 bits binaries are supported
The goal here is to help 3rd party applications (including ports) to determine
if the host do support linux emulation
Reviewed by: dchagin
MFC after: 1 week
Relnotes: yes
Differential Revision: D5830
Simplify and unify placeholder type definitions.
Reviewed by: jhb
Sponsored by: The FreeBSD Foundation
Differential revision: https://reviews.freebsd.org/D5771
This moves the enabling of interrupts slightly earlier (the old location
was still before devices were enumerated and probed) and does it in the
interrupt code (rather than in the device configuration code). This
also avoids tripping over an assertion on the first TLB shootdown with
earlier AP startup.
Reviewed by: kib
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D5710
