sys/conf/makeLINT.mk to only do certain things for certain
architectures.
Note that neither arm nor mips have the Makefile there, thus
essentially not (yet) supporting LINT. This would enable them
do add special treatment to sys/conf/makeLINT.mk as well chosing
one of the many configurations as LINT.
This is a hack of doing this and keeping it in a separate commit
will allow us to more easily identify and back it out.
Discussed on/with: arch, jhb (as part of the LINT-VIMAGE thread)
MFC after: 1 month
while in kernel mode, and later changing signal mask to block the
signal, was fixed for sigprocmask(2) and ptread_exit(3). The same race
exists for sigreturn(2), setcontext(2) and swapcontext(2) syscalls.
Use kern_sigprocmask() instead of direct manipulation of td_sigmask to
reschedule newly blocked signals, closing the race.
Reviewed by: davidxu
Tested by: pho
MFC after: 1 month
the memory or D-cache, depending on the semantics of the platform.
vm_sync_icache() is basically a wrapper around pmap_sync_icache(),
that translates the vm_map_t argumument to pmap_t.
o Introduce pmap_sync_icache() to all PMAP implementation. For powerpc
it replaces the pmap_page_executable() function, added to solve
the I-cache problem in uiomove_fromphys().
o In proc_rwmem() call vm_sync_icache() when writing to a page that
has execute permissions. This assures that when breakpoints are
written, the I-cache will be coherent and the process will actually
hit the breakpoint.
o This also fixes the Book-E PMAP implementation that was missing
necessary locking while trying to deal with the I-cache coherency
in pmap_enter() (read: mmu_booke_enter_locked).
The key property of this change is that the I-cache is made coherent
*after* writes have been done. Doing it in the PMAP layer when adding
or changing a mapping means that the I-cache is made coherent *before*
any writes happen. The difference is key when the I-cache prefetches.
compiled to use the Medium/Low code model, which we currently default
to for the userland. GNU/Linux has moved their default to Medium/Middle
some time ago, which probably explains why the current GNU ld(1) uses
a base in the range between 32 and 44 bits instead.
Submitted by: kib
by looking at the bases used for non-relocatable executables by gnu ld(1),
and adjusting it slightly.
Discussed with: bz
Reviewed by: kan
Tested by: bz (i386, amd64), bsam (linux)
MFC after: some time
has proven to have a good effect when entering KDB by using a NMI,
but it completely violates all the good rules about interrupts
disabled while holding a spinlock in other occasions. This can be the
cause of deadlocks on events where a normal IPI_STOP is expected.
* Adds an new IPI called IPI_STOP_HARD on all the supported architectures.
This IPI is responsible for sending a stop message among CPUs using a
privileged channel when disponible. In other cases it just does match a
normal IPI_STOP.
Right now the IPI_STOP_HARD functionality uses a NMI on ia32 and amd64
architectures, while on the other has a normal IPI_STOP effect. It is
responsibility of maintainers to eventually implement an hard stop
when necessary and possible.
* Use the new IPI facility in order to implement a new userend SMP kernel
function called stop_cpus_hard(). That is specular to stop_cpu() but
it does use the privileged channel for the stopping facility.
* Let KDB use the newly introduced function stop_cpus_hard() and leave
stop_cpus() for all the other cases
* Disable interrupts on CPU0 when starting the process of APs suspension.
* Style cleanup and comments adding
This patch should fix the reboot/shutdown deadlocks many users are
constantly reporting on mailing lists.
Please don't forget to update your config file with the STOP_NMI
option removal
Reviewed by: jhb
Tested by: pho, bz, rink
Approved by: re (kib)
system for configuring machine-dependent memory attributes: ..."). In
r195649, the "vm_cache_mode_t/vm_memattr_t" parameter was removed from
vm_phys_alloc_contig().
Approved by: re (kensmith)
dependent memory attributes:
Rename vm_cache_mode_t to vm_memattr_t. The new name reflects the
fact that there are machine-dependent memory attributes that have
nothing to do with controlling the cache's behavior.
Introduce vm_object_set_memattr() for setting the default memory
attributes that will be given to an object's pages.
Introduce and use pmap_page_{get,set}_memattr() for getting and
setting a page's machine-dependent memory attributes. Add full
support for these functions on amd64 and i386 and stubs for them on
the other architectures. The function pmap_page_set_memattr() is also
responsible for any other machine-dependent aspects of changing a
page's memory attributes, such as flushing the cache or updating the
direct map. The uses include kmem_alloc_contig(), vm_page_alloc(),
and the device pager:
kmem_alloc_contig() can now be used to allocate kernel memory with
non-default memory attributes on amd64 and i386.
vm_page_alloc() and the device pager will set the memory attributes
for the real or fictitious page according to the object's default
memory attributes.
Update the various pmap functions on amd64 and i386 that map pages to
incorporate each page's memory attributes in the mapping.
Notes: (1) Inherent to this design are safety features that prevent
the specification of inconsistent memory attributes by different
mappings on amd64 and i386. In addition, the device pager provides a
warning when a device driver creates a fictitious page with memory
attributes that are inconsistent with the real page that the
fictitious page is an alias for. (2) Storing the machine-dependent
memory attributes for amd64 and i386 as a dedicated "int" in "struct
md_page" represents a compromise between space efficiency and the ease
of MFCing these changes to RELENG_7.
In collaboration with: jhb
Approved by: re (kib)
1. USB_VERBOSE is more consistent with USB_DEBUG,
2. sys/dev/usb/usb_device.c uses option USB_VERBOSE and
not USBVERBOSE.
POLA with the USBVERBOSE option as it's found in 7-STABLE
has been considered but found insignificant in the face
of the USB stack overhaul.
Approved by: re (kensmith)
o add to platforms where it was missing (arm, i386, powerpc, sparc64, sun4v)
o define as "1" on amd64 and i386 where there is no restriction
o make the type returned consistent with ALIGN
o remove _ALIGNED_POINTER
o make associated comments consistent
Reviewed by: bde, imp, marcel
Approved by: re (kensmith)
More applications (including Firefox) seem to depend on this nowadays,
so not having this enabled by default is a bad idea.
Proposed by: miwi
Patch by: Florian Smeets <flo kasimir com>
Approved by: re (kib)
required by video card drivers. Specifically, this change introduces
vm_cache_mode_t with an appropriate VM_CACHE_DEFAULT definition on all
architectures. In addition, this changes adds a vm_cache_mode_t parameter
to kmem_alloc_contig() and vm_phys_alloc_contig(). These will be the
interfaces for allocating mapped kernel memory and physical memory,
respectively, with non-default cache modes.
In collaboration with: jhb
- Modules and kernel code alike may use DPCPU_DEFINE(),
DPCPU_GET(), DPCPU_SET(), etc. akin to the statically defined
PCPU_*. Requires only one extra instruction more than PCPU_* and is
virtually the same as __thread for builtin and much faster for shared
objects. DPCPU variables can be initialized when defined.
- Modules are supported by relocating the module's per-cpu linker set
over space reserved in the kernel. Modules may fail to load if there
is insufficient space available.
- Track space available for modules with a one-off extent allocator.
Free may block for memory to allocate space for an extent.
Reviewed by: jhb, rwatson, kan, sam, grehan, marius, marcel, stas
goal of shipping 8.0 with MAC support in the default kernel. No policies
will be compiled in or enabled by default, but it will now be possible to
load them at boot or runtime without a kernel recompile.
While the framework is not believed to impose measurable overhead when no
policies are loaded (a result of optimization over the past few months in
HEAD), we'll continue to benchmark and optimize as the release approaches.
Please keep an eye out for performance or functionality regressions that
could be a result of this change.
Approved by: re (kensmith)
Obtained from: TrustedBSD Project
The system hostname is now stored in prison0, and the global variable
"hostname" has been removed, as has the hostname_mtx mutex. Jails may
have their own host information, or they may inherit it from the
parent/system. The proper way to read the hostname is via
getcredhostname(), which will copy either the hostname associated with
the passed cred, or the system hostname if you pass NULL. The system
hostname can still be accessed directly (and without locking) at
prison0.pr_host, but that should be avoided where possible.
The "similar information" referred to is domainname, hostid, and
hostuuid, which have also become prison parameters and had their
associated global variables removed.
Approved by: bz (mentor)
I don't want people to override the mutex when allocating a TTY. It has
to be there, to keep drivers like syscons happy. So I'm creating a
tty_alloc_mutex() which can be used in those cases. tty_alloc_mutex()
should eventually be removed.
The advantage of this approach, is that we can just remove a function,
without breaking the regular API in the future.
possible future I-cache coherency operation can succeed. On ARM
for example the L1 cache can be (is) virtually mapped, which
means that any I/O that uses temporary mappings will not see the
I-cache made coherent. On ia64 a similar behaviour has been
observed. By flushing the D-cache, execution of binaries backed
by md(4) and/or NFS work reliably.
For Book-E (powerpc), execution over NFS exhibits SIGILL once in
a while as well, though cpu_flush_dcache() hasn't been implemented
yet.
Doing an explicit D-cache flush as part of the non-DMA based I/O
read operation eliminates the need to do it as part of the
I-cache coherency operation itself and as such avoids pessimizing
the DMA-based I/O read operations for which D-cache are already
flushed/invalidated. It also allows future optimizations whereby
the bcopy() followed by the D-cache flush can be integrated in a
single operation, which could be implemented using on-chips DMA
engines, by-passing the D-cache altogether.
a fair number of static data structures, making this an unlikely
option to try to change without also changing source code. [1]
Change default cache line size on ia64, sparc64, and sun4v to 128
bytes, as this was what rtld-elf was already using on those
platforms. [2]
Suggested by: bde [1], jhb [2]
MFC after: 2 weeks
CACHE_LINE_SIZE constant. These constants are intended to
over-estimate the cache line size, and be used at compile-time
when a run-time tuning alternative isn't appropriate or
available.
Defaults for all architectures are 64 bytes, except powerpc
where it is 128 bytes (used on G5 systems).
MFC after: 2 weeks
Discussed on: arch@
driver in Linux 2.6. uscanner was just a simple wrapper around a fifo and
contained no logic, the default interface is now libusb (supported by sane).
Reviewed by: HPS
to the full path of the image that is being executed.
Increase AT_COUNT.
Remove no longer true comment about types used in Linux ELF binaries,
listed types contain FreeBSD-specific entries.
Reviewed by: kan
kernel one as the non-faulting flush address in the loader so
we can can change KERNBASE and VM_MIN_KERNEL_ADDRESS if we
ever want to without needing to worry about using a compatible
loader.
- Correctly check for LOADER_DEBUG.
- Add a missing const for page_sizes[].
This file was missed in r188455.
of OFW access semantics, in order to allow future support for real-mode
OF access and flattened device frees. OF client interface modules are
implemented using KOBJ, in a similar way to the PPC PMAP modules.
Because we need Open Firmware to be available before mutexes can be used on
sparc64, changes are also included to allow KOBJ to be used very early in
the boot process by only using the mutex once we know it has been initialized.
Reviewed by: marius, grehan
the code for parsing interrupt maps) to PowerPC and reflect their new MI
status by moving them to the shared dev/ofw directory.
This commit also modifies the OFW PCI enumeration procedure on PowerPC to
allow the bus to find non-firmware-enumerated devices that Apple likes to add,
and adds some useful Open Firmware properties (compat and name) to the pnpinfo
string of children on OFW SBus, EBus, PCI, and MacIO links. Because of the
change to PCI enumeration on PowerPC, X has started working again on PPC
machines with Grackle hostbridges.
Reviewed by: marius
Obtained from: sparc64
Sgtty is a programming interface that has been replaced by termios over
the years. In June we already removed <sgtty.h>, which exposes the
ioctl()'s that are implemented by this interface. The importance of this
flag is overrated right now.
and ifnet functions
- add memory barriers to <machine/atomic.h>
- update drivers to only conditionally define their own
- add lockless producer / consumer ring buffer
- remove ring buffer implementation from cxgb and update its callers
- add if_transmit(struct ifnet *ifp, struct mbuf *m) to ifnet to
allow drivers to efficiently manage multiple hardware queues
(i.e. not serialize all packets through one ifq)
- expose if_qflush to allow drivers to flush any driver managed queues
This work was supported by Bitgravity Inc. and Chelsio Inc.
