Don't arbitrarily limit the initiator ID of the card to something <= 7.
Fix a bug in the checksum code that would incorrectly prevent a valid
checksum of zero. (cp)
Don't touch rely on seeprom data when configuring termination. We may
not have seeprom data. (cp)
Treat all ULTRA2 capable adapters the same way when reading or writing
the BRDCTL register. We previously only did this correctly for aic7890/91
chips. This should correct some problems with termination settings on
aic7896/97 adapters. (cp)
Changes marked with "(cp)"
Pointed out by: Chuck Paterson <cp@bsdi.com>
Also, optimize out a mess of #if's that were duplicating work already
done by config(8). For example, if a file is marked as
"dev/sound/pci/foo.c optional pcm pci" then it's only added if pcm *and*
pci are present, so #if NPCM > 0 and #if NPCI > 0 are totally redundant.
A bit more work is still needed.
Discussed with: cg (a few weeks ago)
aic7xxx.c:
Add a function for sucking firmware out of the controller
prior to reset.
Remove some inline bloat from functions that should not have
been inlined.
During initialization, wait 1ms after the chip reset before
touching any registers. You can get machine checks on certain
architectures (Atari I think?) without the delay.
Return CAM_REQ_CMP for external BDR requests instead
of CAM_BDR_SENT.
Bump some messages to bootverbose levels above 1.
Don't clear any negotiated sync rate if the target rejects
a WDTR message. The sync rate is only cleared if the target
accepts a WDTR message.
Fix a small bug in the mesgin handling code that could cause
us to believe that we had recieved a message that was actually
received by another target. This could only confuse us in
some very rare transmission negotiation scenarios.
Remove some unecessary cleanup of residual information after
a residual is reported. The sequencer does this when the
command is queued now.
some time ago that changes kern.randompid from a boolean to a randomness
range for the next pid assigment. Too high causes a lot of extra work
to scan for free pids, and too low merely wastes randomness entropy. It's
still possible to select a completely random range by using PID_MAX (100k)
or -1 as a shortcut to mean "the whole range".
Also, don't waste randomness when doing a wraparound.
that the read EEPROM command has time to execute.
I didn't observe any difference in behavior on my test system but
this is the documented "correct behavior".
We now correctly skip boards that have PnP support enabled, or are in
test mode. The 3c509s support a number of combinations of device
probing, as per the databook.
- ISA only
- PnP only
- ISA or PnP
We will allow cards that can be dealt with by PnP to be attached by the
PnP enumerator.
This fixes the bogus detection of boards at weird ioports.
programming practices. It seems that newer fdc chips have an
alternative way of setting the transfer speed (including high speed
modes for floppy tape) that doesn't use the control register (which
we don't support - we use the old way only). So, they (the BIOS
programmers) sometimes leave out the 0x3f6 control register from
the PnP ports descriptor(!!). "Hey, it works with windows, so
what's the problem?" :-( Anyway, this hack tries to compensate
for that. This was discussed with dfr (who did the pnp attachment).
returns "0" on failure, which is indistinguishable from (say) irq 0. This
should stop a couple of stray messages that turn up.
Also, if a BUS_SETUP_INTR() fails with INTR_TYPE_FAST, try falling back to
a normal interrupt. This might help pccard folks with a shared slot
interrupt. This whole thing needs to be revisited.
- Implement 'ipfw tee' (finally)
- Divert packets by calling new function divert_packet() directly instead
of going through protosw[].
- Replace kludgey global variable 'ip_divert_port' with a function parameter
to divert_packet()
- Replace kludgey global variable 'frag_divert_port' with a function parameter
to ip_reass()
- style(9) fixes
Reviewed by: julian, green
forgot to do when he converted it to newbus.
Note: make *sure* to remove any old joy.o object files from your kernel
build directories in order to be sure the joy driver is properly recompiled.
Noticed by: phk
before selecting a mode. The Seeq PHY chips on the Adaptec cards that
use the AIC-6915 controller seem to need it in order to get them to
change modes correctly.
This corrects a problem that I noticed where my ANA-62022 board failed
to correctly program the full duplex bit in the macconfig1 register
when the interface was brought up. Running ifconfig sf0 would mask this
problem in some cases because polling the PHY status would cause the
miibus code to notice that full duplex was now needed and the statchg
callback would be invoked to configure the duplex setting. However it
would still get it wrong other times.
Also changed sf_miibus_statchg() to program the IPG register to match
the duplex setting in accordance with Adaptec manual's recommendations
(0x15 for full duplex, 0x11 for half duplex).
joystick port on PnP sound cards that have a suitable device ID on them.
Doug Rabson added timer code so it didn't have to beat on the isa timer.
Submitted by: Takanori Watanabe <takawata@shidahara1.planet.sci.kobe-u.ac.jp>
mutate some panics to kasserts
add more spl protection
PR: kern/14990
Partially Submitted by: Vladimir N.Silyaev <vns@delta.odessa.ua>
Reviewed by: dfr
which it replaces. The new driver supports all of the chips supported
by the ones it replaces, as well as many DEC/Intel 21143 10/100 cards.
This also completes my quest to convert things to miibus and add
Alpha support.
