buffer had to be left on the head of the queue for [bufq]disksort()
to sort against. This isn't right for devices that can support multiple
active i/o's, and only the fd driver did it. "Fixing" this in rev.1.36
of ufs_disksubr.c broke the fd driver in much the same way as rev.1.52
of <sys/buf.h> broke it (see rev.1.119).
Bug reported and fix tested by: dt
+ ECP parallel port chipset FIFO detection
+ DMA+FIFO parallel I/O handled as chipset specific
+ nlpt updated in order to use the above enhanced parallel I/O.
Use 'lptcontrol -e' to use enhanced I/O
+ Various options documented in LINT
+ Full IEEE1284 NIBBLE and BYTE modes support. See ppbus(4) for
an overview of the IEEE1284 standard
+ Detection of PnP parallel devices at boot
+ Read capability added to nlpt driver to get IEEE1284 compliant
printer status with a simple 'cat /dev/lpt0'
+ IEEE1284 peripheral emulation added to BYTE mode. Two computers
may dialog according to IEEE1284 signaling method.
See PERIPH_1284 option and /sys/dev/ppbus/ppi.c
All this code is supposed to provide basic functions for IEEE1284 programming.
ppi.c and nlpt.c may act as examples.
floppy is used on the toshiba Libretto line of subnotebook computers.
It differs from a normal floppy in that you must use PIO rather than
DMA to transfer the data.
To enable this, you must add options "FDC_YE" to your kernel. I don't
have a machine that has a floppy and a pcmcia slot to test to make
sure that this doesn't impact normal floppy units, so I've left this as
an option.
I have ported this to -current and made an attempt to ensure that the
indentation conforms to style(9), aka the bruce filter.
Reviewed by: nate, markm
Submitted by: David Horwitt (dhorwitt@ucsd.edu)
for possible buffer overflow problems. Replaced most sprintf()'s
with snprintf(); for others cases, added terminating NUL bytes where
appropriate, replaced constants like "16" with sizeof(), etc.
These changes include several bug fixes, but most changes are for
maintainability's sake. Any instance where it wasn't "immediately
obvious" that a buffer overflow could not occur was made safer.
Reviewed by: Bruce Evans <bde@zeta.org.au>
Reviewed by: Matthew Dillon <dillon@apollo.backplane.com>
Reviewed by: Mike Spengler <mks@networkcs.com>
* Update drivers to the latest version of the bus interface.
The ISA drivers' use of the new resource api is minimal. Garrett has
some much cleaner drivers which should be more easily shared between
i386 and alpha. This has only been tested on cia based machines. It
should work on lca and apecs but I might have broken something.
truncated to 32 bits.
* Change the calling convention of the device mmap entry point to
pass a vm_offset_t instead of an int for the offset allowing
devices with a larger memory map than (1<<32) to be supported
on the alpha (/dev/mem is one such).
These changes are required to allow the X server to mmap the various
I/O regions used for device port and memory access on the alpha.
a vga.
* Fix broken logic in syscons for a failed probe.
* Fix AlphaStation 500/600 so that non-serial consoles are supported.
Submitted by: Thomas Valentino Crimi <tcrimi+@andrew.cmu.edu> (vga bits),
Andrew Gallatin <gallatin@cs.duke.edu> (AS500/AS600)
hasseen_isadev so this will be less noisy when conflicts do exist.
Also eliminate redundant warnings about conflicts.
Requested by: bde
Reviewed by: gibbs
o For bt and aha only probe the one I/O range if a specific I/O is specified
in the config file.
o Don't even try to probe I/O ranges that have been seen already.
o If we conflict with an IRQ or DRQ, then fail the probe.
Requested by: bde, gibbs
Approved by: jkh
went backwards when interrupts were masked for more than one i8254
interrupt period. It sometimes went backwards when the i8254 counter
was reprogrammed. Neither of these should happen in normal operation.
Update the i8254 timecounter support variables atomically. Calling
timecounter functions from fast interrupt handlers may actually work
in all cases now.
and use this when masking/unmasking interrupts.
Maintain a mapping from (iopaic number, int pin) tuple to irq number,
and use this when configuring devices and programming the ioapics.
Previous code assumed that irq number was equal to int pin number, and
that the ioapic number was 0.
Don't let an AP enter _cpu_switch before all local apics are initialized.
for the Lite2 fix for always returning EIO in dead_read().
Cleaned up the cdevswitch initializers for all tty drivers.
Removed explicit calls to ttsetwater() from all (tty) drivers. ttsetwater()
is now called centrally for opens, not just for parameter changes.
for 1 second's worth of input) and larger tty output buffers. The
interrupt-level buffers are still too small for speeds above 115200
bps (only a little too small for 230400 bps if RTS flow control is
enabled).
Don't call ttsetwater() explicitly in open(). It is now called for
the TTYDISC l_open() and should be static.
Don't attempt to register the cdevsw more than once.
instead of at compile time using ifdefs.
Use _swi_null instead of dummycamisr. CAM and dpt should call
register_swi() instead of hacking on ihandlers[] directly.
hopefully become a portable driver usable by all architectures. The api
support files have had to be copied to sys/alpha/include since userland
programs expect to find them in <machine/*.h>.
All the revision history of the i386 syscons has been retained by a
repository copy.
- ppbus now supports PLIP via the if_plip driver
- ieee1284 infrastructure added, including parallel-port PnP
- port microsequencer added, for scripting the sort of port I/O
that is common with parallel devices without endless calls up and down
through the driver structure.
- improved bus ownership behaviour among the ppbus-using drivers.
- improved I/O chipset feature detection
The vpo driver is now implemented using the microsequencer, leading to
some performance improvements as well as providing an extensive example
of its use.
Reviewed by: msmith
Submitted by: Nicolas Souchu <Nicolas.Souchu@prism.uvsq.fr>
saver and splash screen can all work properly with syscons. Note that
the splash screen option (SC_SPLASH_SCREEN) does not work yet, as it
requires additional code from msmith.
- Reorganized the splash screen code to match the latest development
in this area.
- Delay screen switch in `switch_scr()' until the screen saver is
stopped, if one is running,
- Start the screen saver immediately, if any, when the `saver' key is
pressed. (There will be another commit for `kbdcontrol' to support
this keyword in the keymap file.)
- Do not always stop the screen saver when mouse-related ioctls
are called. Stop it only if the mouse is moved or buttons are
clicked; don't stop it if any other mouse ioctls are called.
2. Added provision to write userland screen savers. (Contact me if you
are interested in writing one.)
- Added CONS_IDLE, CONS_SAVERMODE, and CONS_SAVERSTART ioctls to
support userland screen savers.
3. Some code clean-ups.
