hash tables used in the sleep queue and turnstile code. Each option adds
a sysctl tree under debug containing the maximum depth of any bucket in
the hash table as well as a separate node for each bucket (or chain)
containing the current depth and maximum depth for that bucket.
originated on RELENG_4 and was ported to -CURRENT.
The scoreboarding code was obtained from OpenBSD, and many
of the remaining changes were inspired by OpenBSD, but not
taken directly from there.
You can enable/disable sack using net.inet.tcp.do_sack. You can
also limit the number of sack holes that all senders can have in
the scoreboard with net.inet.tcp.sackhole_limit.
Reviewed by: gnn
Obtained from: Yahoo! (Mohan Srinivasan, Jayanth Vijayaraghavan)
your (network) modules as well as any userland that might make sense of
sizeof(struct ifnet).
This does not change the queueing yet. These changes will follow in a
seperate commit. Same with the driver changes, which need case by case
evaluation.
__FreeBSD_version bump will follow.
Tested-by: (i386)LINT
- Connect geom_stripe and geom_nop modules to the build.
- Connect STRIPE and NOP classes to the LINT build.
- Disconnect gconcat(8) from the build.
Supported by: Wheel - Open Technologies - http://www.wheel.pl
an option. Note that this option doesn't follow the normal USB_ or
Uxxx_ convention. That's because it is this way in the upstream
provider and I didn't want to change that.
returns okay when HW probe fails. This happens when comconsole flag is
set but VGA console is used instead.
Back out requested by: bde (He will be looking at other solutions from scratch)
synchronization protecting against dynamic load and unload of MAC
policies, and instead simply blocks load and unload. In a static
configuration, this allows you to avoid the synchronization costs
associated with introducing dynamicism.
Obtained from: TrustedBSD Project
Sponsored by: DARPA, McAfee Research
- Define option FORCECONSPEED to force the serial console to
be CONSPEED. I've run into a lot of boards in which
the detect for prior speed doesn't work and ends up with
broken console since it is at the wrong speed.
- If a serial port is marked as a console, but console=vidconsole
and if the serial ports doesn't exist it will be probed and
attached at a 8250 chip. Then writes to that will freeze the
system.
- Add an option flags 0x400000 to mark this as a potential
comconsole in-case the one flaged with 0x10 does not exist
in the system.
This makes it easier to deploy on systems with one or two serial ports.
Obtained from: IronPort
to awaken all waiters when a contested mutex is released instead of just
the highest priority waiter. If the various threads are awakened in
sequence then each thread may acquire and release the lock in question
without contention resulting in fewer expensive unlock and lock
operations. This old behavior of waking just the highest priority is
still used if this option is specified. Making the algorithm conditional
on a kernel option will allows us to benchmark both cases later and
determine which one should be used by default.
Requested by: tanimura-san
mini-layer. I don't have time to bing it forward into the GEOM world, and
no one else has stepped forward to claim it. It'll be in the Attic for safe
keeping for now.
ethernet (tested) and FDDI (not tested). The main use for this is on ADSL (or
other ATM) connections where bridged ethernet is used, PPPoE being a prime
example.
There is no manual page as yet, I will write one shortly.
Reviewed by: harti
generic watchdoc(9) interface.
Make watchdogd(8) perform as watchdog(8) as well, and make it
possible to specify a check command to run, timeout and sleep
periods.
Update watchdog(4) to talk about the generic interface and add
new watchdog(8) page.
pf/pflog/pfsync as modules. Do not list them in NOTES or modules/Makefile
(i.e. do not connect it to any (automatic) builds - yet).
Approved by: bms(mentor)
also prints the actual numerical value of the symbol in question.
Users of addr2line(1) will be less proficient in hex arithmetic as a
consequence.
This amongst other things means that traceback lines change from:
siointr1(c4016800,c073bda0,0,c06b699c,69f) at siointr1+0xc5
to
siointr1(c4016800,c073bda0,0,c06b699c,69f) at 0xc062b0bd = siointr1+0xc5
I made this an option to avoid bikesheds.
~
~
~
This is the first of two commits; bringing in the kernel support first.
This can be enabled by compiling a kernel with options TCP_SIGNATURE
and FAST_IPSEC.
For the uninitiated, this is a TCP option which provides for a means of
authenticating TCP sessions which came into being before IPSEC. It is
still relevant today, however, as it is used by many commercial router
vendors, particularly with BGP, and as such has become a requirement for
interconnect at many major Internet points of presence.
Several parts of the TCP and IP headers, including the segment payload,
are digested with MD5, including a shared secret. The PF_KEY interface
is used to manage the secrets using security associations in the SADB.
There is a limitation here in that as there is no way to map a TCP flow
per-port back to an SPI without polluting tcpcb or using the SPD; the
code to do the latter is unstable at this time. Therefore this code only
supports per-host keying granularity.
Whilst FAST_IPSEC is mutually exclusive with KAME IPSEC (and thus IPv6),
TCP_SIGNATURE applies only to IPv4. For the vast majority of prospective
users of this feature, this will not pose any problem.
This implementation is output-only; that is, the option is honoured when
responding to a host initiating a TCP session, but no effort is made
[yet] to authenticate inbound traffic. This is, however, sufficient to
interwork with Cisco equipment.
Tested with a Cisco 2501 running IOS 12.0(27), and Quagga 0.96.4 with
local patches. Patches for tcpdump to validate TCP-MD5 sessions are also
available from me upon request.
Sponsored by: sentex.net
lots of old interfaces, and digi now supports all cards that dgb
supported. The author of the driver says that this is no longer
necessary.
Approved by: babkin@
Requested by: jhb
Initialize the real mode stack. This is needed at least for the return
address from the lcall.
Requested by: takawata
Fix style bugs in acpi_wakecode.S
Requested by: bde
Remove the kernel option now that we have the tunable.
dcons(4): very simple console and gdb port driver
dcons_crom(4): FireWire attachment
dconschat(8): User interface to dcons
Tested with: i386, i386-PAE, and sparc64.
enable strict checks of the AML. Our default behavior will be to relax
checks to work on as many platforms as possible. Also clean up and document
other ACPI options while I'm here.
Second (PPS) timing interface. The support is non-optional and by
default uses the DCD line signal as the pulse input. A compile-time
option (UART_PPS_ON_CTS) can be used to have uart(4) use the CTS line
signal.
Include <sys/timepps.h> in uart_bus.h to avoid having to add the
inclusion of that header in all source files.
Reviewed by: phk
FIDs to be 128-bits wide and adds support for realms.
Add a new CODA_COMPAT_5 option, which requests support for the old
Coda 5.x interface instead of the new one.
Create a new coda5.ko module that supports the 5.x interface, and make
the existing coda.ko module use the new 6.x interface. These modules
cannot both be loaded at the same time.
Obtained from: Jan Harkes & the coda-6.0.2 distribution,
NetBSD (drochner) (CODA_COMPAT_5 option).
Restructure the way ATA/ATAPI commands are processed, use a common
ata_request structure for both. This centralises the way requests
are handled so locking is much easier to handle.
The driver is now layered much more cleanly to seperate the lowlevel
HW access so it can be tailored to specific controllers without touching
the upper layers. This is needed to support some of the newer
semi-intelligent ATA controllers showing up.
The top level drivers (disk, ATAPI devices) are more or less still
the same with just corrections to use the new interface.
Pull ATA out from under Gaint now that locking can be done in a sane way.
Add support for a the National Geode SC1100. Thanks to Soekris engineering
for sponsoring a Soekris 4801 to make this support.
Fixed alot of small bugs in the chipset code for various chips now
we are around in that corner anyways.
found only many tv-cards.
We currently use more ore less evil hacks (slow_msp_audio sysctl) to
configure the various variants of these chips in order to have
stereo autodetection work. Nevertheless, this doesn't always work
even though it _should_, according to the specs.
This is, for example, the case for some popular Hauppauge models sold
sold in Germany.
However, the Linux driver always worked for me and others. Looking at
the sourcecode you will find that the linux-driver uses a very much
enhanced approach to program the various msp34xx chipset variants,
which is also found in the specs for these chips.
This is a port of the Linux MSP34xx code, written by Gerd Knorr
<kraxel@bytesex.org>, who agreed to re-release his code under a
BSD license for this port.
A new config option "BKTR_NEW_MSP34XX_DRIVER" is added, which is required
to enable the new driver. Otherwise the old code is used.
The msp34xx.c file is diff-reduced to the linux-driver to make later
modifications easier, thus it doesn't follow style(9) in most cases.
Approved by: roger (committing this, no time to test/review),
keichii (code review)
