* If the first call succeeded but failed to transmit, a timer would
reschedule it via bar_timeout(). Unfortunately bar_timeout() didn't
check the return value from the ieee80211_send_bar() reattempt and
if that failed (eg the driver ic_raw_xmit() failed), it would never
re-arm the timer.
* If BARPEND is cleared (which ieee80211_send_bar() will do if it can't
TX), then re-arming the timer isn't enough - once bar_timeout() occurs,
it'll see BARPEND is 0 and not run through the rest of the routine.
So when rearming the timer, also set that flag.
* If the TX wasn't occuring, bar_tx_complete() wouldn't be called and the
driver callback wouldn't be called either. So the driver had no idea
that the BAR TX attempt had failed. In the ath(4) case, TX would stay
paused.
(There's no callback to indicate that BAR TX had failed or not;
only a "BAR TX was attempted". That's a separate, later problem.)
So call the driver callback (ic_bar_response()) before the ADDBA session
is torn down, so it has a chance of being notified that things didn't
quite go to plan.
I've verified that yes, this does suspend traffic for ath(4), retry BAR
TX even if the driver is failing ic_raw_xmit(), and then eventually giving
up and sending a DELBA. I'll address the "out of ath_buf" issue in ath(4)
in a subsequent commit - this commit just fixes the edge case where any
driver is (way) out of internal buffers/descriptors and fails frame TX.
PR: kern/168170
Reviewed by: bschmidt
MFC after: 1 month
* Modified hwmp_recv_preq:
o cleaned up code, removed rootmac variable because preq->origaddr
is the root when we recevie a Proactive PREQ;
o Modified so that a PREP in response of a Proactive PREQ is unicast,
a PREP is ALWAYS unicast;
* Modified hwmp_recv_prep:
o Before we mark a route to be valid we should remove the discovery
flag and then mark it valid in such a way we wont lose the isgate flag;
Approved by: adrian
* Added a new discovery flag IEEE80211_MESHRT_FLAGS_DISCOVER;
* Modified ieee80211_ioctl.h to include IEEE80211_MESHRT_FLAGS_DISCOVER;
* Added hwmp_rediscover_cb, which will be called by a timeout to do
rediscovery if we have not reach max number of preq discovery;
* Modified hwmp_discover to setup a callout for path rediscovery;
* Added to ieee80211req_mesh_route to have a back pointer to ieee80211vap
for the discovery callout context;
* Modified mesh_rt_add_locked arguemnt from ieee80211_mesh_state to
ieee80211vap, this because we have to initialize the above back pointer;
Approved by: adrian
* Renamed IEEE80211_ELEMID_MESHPANN to IEEE80211_ELEMID_MESHGANN according to
amendment;
* Added IEEE80211_IOC_MESH_GATE that controls whether Mesh Gate Announcement
is activated or not;
* Renamed all flags from Portal to Gate in HWMP frames;
* Removed IEEE80211_ACTION_MESHPANN enum cause its part of the Mesh Action
category now as per amendment;
* Renamed IEEE80211_MESHFLAGS_PORTAL to IEEE80211_MESHFLAGS_GATE in
ieee80211_mesh_state flags;
* Modified ieee80211_hwmp.c/ieee80211_mesh.c to use new GATE flags;
Approved by: adrian
* Introduced a new HWMP sysctl, Root Confirmation Interval;
* Added hr_lastrootconf to hwmp_route, is for ratecheck for a specific ROOT;
* We missed reading RANN.interval subfield from a RANN frame before;
* Updated hwmp_recv_rann according to amendment, see comments;
Approved by: adrian
* Added mpp_senderror for Mesh Path Selection protocol;
* Added hwmp_senderror that will send an HWMP PERR according to the
supplied reason code;
* Call mpp_senderror when deleting a route with correct reason code
for whether the route is marked proxy or not;
* Call mpp_senderror when trying to forward an individually addressed
frame and there is no forwarding information;
Approved by: adrian
* When receiving a Proactive PREQ dont return after processing it but propagate;
* When we propagate we should not enforce ratechecking;
* Added checking for multiple pred ID detection;
* Storing proxy orig address when PREQ is not for us;
Approved by: adrian
* Moved hs_lastpreq to be hr_lastpreq cause this rate check should be per
target mesh STA according to amendment (NB: not applicable for PERR);
* Modified hwmp_send_preq to use two extra arguments for last sent PREQ and
minimum PREQ interval;
* hwmp_send_preq is called with last two arguments equal to NULL when sending
Proactive PREQs cause the call back task enforces the rate check;
Approved by: adrian
* Added assertion in mesh_rt_update;
* Fixed some prep propagation that where multicast, ALL PREPS ARE UNICAST;
* Fixed PREP acceptance criteria;
* Fixed some PREP debug messages;
* HWMP intermediate reply (PREP) should only be sent if we have newer
forwarding infomration (FI) about target;
* Fixed PREP propagation condition and PREP w/ AE handling;
* Ignore PREPs that have unknown originator.
* Removed old code inside PREP that was for proactive path building
to root mesh;
Other errors include:
* use seq number of target and not orig mesh STA;
* Metric is what we have stored in our FI;
* Error in amendment, Hop count is not 0 but equals FI hopcount for target;
Approved by: adrian
* In mesh_recv_indiv_data_to_fwd update route entry for both meshDA and meshSA;
* In mesh_recv_indiv_data_to_me update route entry for meshSA;
* in ieee80211_mesh_rt_update put code so that a proxy entry that is gated
by us (number of hops == 0) is never invalidated;
* Fixed so that we always call ieee80211_mesh_rt_update with lifetime in ms;
Approved by: adrian
* Modified HWMP PREP/PREQ to contain a proxy entry and also changed PREP
frame processing according to amendment as following:
o Fixed PREP to always update/create if acceptance criteria is meet;
o PREQ processing to reply if request is for a proxy entry that is
proxied by us;
o Removed hwmp_discover call from PREQ, because sending a PREP will
build the forward path, and by receving and accepting a PREQ we
have already built the reverse path (non-proactive code);
* Disabled code for pro-active in PREP for now (will make a separate patch for
pro-active HWMP routing later)
* Added proxy information for a Mesh route, mesh gate to use and proxy seqno;
* Modified ieee80211_encap according to amendment;
* Introduced Mesh control address extension enum and removed unused struct,
also rename some structure element names.
* Modified mesh_input and added mesh_recv_* that should verify and process mesh
data frames according to 9.32 Mesh forwarding framework in amendment;
* Modified mesh_decap accordingly to changes done in mesh control AE struct;
Approved by: adrian
* Introduced ieee80211_mesh_rt_update that updates a route with the
maximum(lifetime left, new lifetime);
* Modified ieee80211_mesh_route struct by adding a lock that will be used
by both ieee80211_mesh_rt_update and precursor code (added in future commit);
* Modified in ieee80211_hwmp.c HWMP code to use new ieee80211_mesh_rt_update;
* Modified mesh_rt_flush_invalid to use new ieee80211_mesh_rt_update;
* mesh_rt_flush also checks that lifetime == 0, this gives route discovery
a change to complete;
* Modified mesh_recv_mgmt case IEEE80211_FC0_SUBTYPE_BEACON:
when ever we received a beacon from a neighbor we update route lifetime;
Approved by: adrian
* Added IEEE80211_MESH_MAX_NEIGHBORS and it is set to 15, same as before;
* Modified mesh_parse_meshpeering_action to verify MPM frame and send
correct reason code for when a frame is rejected according to standard spec;
* Modified mesh_recv_action_meshpeering_* according to the standard spec;
* Modified mesh_peer_timeout_cb to always send CLOSE frame when in CONFIRMRCV
state according to the standard spec;
Approved by: adrian
* Old struct ieee80211_meshpeer_ie had wrong peer_proto field size;
* Added IEEE80211_MPM_* size macros;
* Created an enum for the Mesh Peering Protocol Identifier field according
to the standard spec and removed old defines;
* Abbreviated Handshake Protocol is not used by the standard anymore;
* Modified mesh_verify_meshpeer to use IEEE80211_MPM_* macros for verification;
* Modified mesh_parse_meshpeering_action to parse complete frame, also to parse
it according to the standard spec;
* Modified ieee80211_add_meshpeer to construct correct MPM frames according to
the standard spec;
Approved by: adrian
* Added new action category IEEE80211_ACTION_CAT_SELF_PROT which is used by 11s
for Mesh Peering Management;
* Updated Self protected enum Action codes to start from 1 instead of 0
according to the standard spec;
* Removed old and wrong action categories IEEE80211_ACTION_CAT_MESHPEERING;
* Modified ieee80211_mesh.c and ieee80211_action.c to use the new action
category code;
* Added earlier verification code in ieee80211_input;
Approved by: adrian
Because the code lacks all the GNU extensions to printf() format stuff,
the compiler doesn't helpfully tell us that I messed up in a previous
commit.
Pointy hat to: adrian, who likely only cares about this because he's the
only one who bothers flipping on net80211 debugging.
Currently, a channel width change updates the 802.11n HT info data in
net80211 but it doesn't trigger any device changes. So the device
driver may decide that HT40 frames can be transmitted but the last
device channel set only had HT20 set.
Now, a task is scheduled so a hardware reset or change isn't done
during any active ongoing RX. It also means that it's serialised
with the other task operations (eg channel change.)
This isn't the final incantation of this work, see below.
For now, any unmodified drivers will simply receive a channel
change log entry. A subsequent patch to ath(4) will introduce
some basic channel change handling (by resetting the NIC.)
Other NICs may need to update their rate control information.
TODO:
* There's still a small window at the present moment where the
channel width has been updated but the task hasn't been fired.
The final version of this should likely pass in a channel width
field to the driver and let the driver atomically do whatever
it needs to before changing the channel.
PR: kern/166286
* Added verify_mesh_*_len functions that verify the length
according to the amendment spec and return number of destination addresses
for allocation of appropriate struct size in memory;
* Modified hwmp_recv_action_meshpath to allocate HWMP ie instead of
storing them on the stack and store all available field according the flags;
* Modify hwmp_add_mesh* to work with all cases of HWMP according to amendment.
* Modify hwmp_send_* to calculate correct len of bytes for the HWMP ie.
* Added new M_80211_MESH_* malloc defines.
* Added macros with magic numbers for HWMP ie sizes according to amendment.
* Added the external address to all HWMP ie structs.
Submitted by: monthadar@gmail.com
* Change in mesh_input to validate that QoS is set and Mesh Control field
is present, also both bytes of the QoS are read;
* Moved defragmentation in mesh_input before we try to forward packet as
inferred from amendment spec, because Mesh Control field only present in first
fragment;
* Changed in ieee80211_encap to set QoS subtype and Mesh Control field present,
only first fragment have Mesh Control field present bit equal to 1;
Submitted by: monthadar@gmail.com
* Moved old categories as specified by D4.0 to be action fields of MESH category
as specified in amendment spec;
* Modified functions to use MESH category and its action fields:
+ ieee80211_send_action_register
+ ieee80211_send_action
+ ieee80211_recv_action_register
+ieee80211_recv_action;
* Modified ieee80211_hwmp_init and hwmp_send_action so they uses correct
action fields as specified in amendment spec;
* Modified ieee80211_parse_action so that it verifies MESH frames.
* Change Mesh Link Metric to use one information element as amendment spec.
Draft 4.0 defined two different information elements for request and response.
Submitted by: monthadar@gmail.com
The scan code unlocks the comlock and calls into the driver. It then
assumes the state hasn't changed from underneath it.
Although I haven't seen this particular condition trigger, I'd like to
be informed if I or anyone else sees it.
What I'm thinking may occur:
* A cancellation comes in during the scan_end call;
* the cancel flag is set;
* but it's never checked, so scandone isn't updated;
* .. and the interface stays in the STA power save mode.
It's a subtle race, if it even exists.
PR: kern/163318
It doesn't _really_ help all that much, I'll commit something to
sys/net/if.c at some point explaining why, but the lock should be held
when checking/manipulating/branching because of said lock.
comlock, I'd like to find and analyse these cases to see if they
really are valid.
So, throw in a lock here and wait for the (hopefully!) inevitable
complaints.
* Change the mesh IE size to be IEEE80211_MESH_CONF_SZ rather than the
size of the structure;
* conf_cap is now a uint8_t rather than a uint16_t (uint16_t in D3.0,
uint8_t in the amendment spec);
* Update mesh config capability bits - earlier bits were from draft X,
current is amendment spec;
* Update the following to be an enum rather than #define and added
a VENDOR entry too from the amendment spec;
IEEE80211_MESHCONF_PATH_*
IEEE80211_MESHCONF_METRIC_*
IEEE80211_MESHCONF_CC_*
IEEE80211_MESHCONF_SYNC_*
IEEE80211_MESHCONF_AUTH_*
* Kept IEEE80211_MESHCONF_FORM_* and IEEE80211_MESHCONF_CAP_* as
defines because they are defined in a way that we need to mask in/out
information;
* In IEEE80211_MESHCONF_CAP_* IEEE80211_MESHCONF_CAP_TBTTA is removed
and 0x80 is made reserved as defined in the amendment spec.
Submitted by: monthadar@gmail.com
Reviewed by: rpaulo
