mirror/freebsd
1
0
Fork 0
mirror of https://git.FreeBSD.org/src.git synced 2024-12-18 10:35:55 +00:00
Code Issues Releases Activity
0981f5f00e
freebsd/sys/dev/aic7xxx/aic79xx_pci.c
Justin T. Gibbs 0794987d01 aic79xx.c: 
Implement the SCB_SILENT flag.  This is useful for
	hushing up the driver during DV or other operations
	that we expect to cause transmission errors.  The
	messages will still print if the SHOW_MASKED_ERRORS
	debug option is enabled.

	Save and restore the NEGOADDR address when setting
	new transfer settings.  The sequencer performs lookups
	in the negotiation table too and it expects NEGOADDR
	to remain consistent across pause/unpause sessions.

	Consistently use "offset" instead of "period" to determine
	if we are running sync or not.

	Add a SHOW_MESSAGES diagnostic for when we assert ATN
	during message processing.

	Print out IU, QAS, and RTI features when showing transfer options.

	Limit the syncrate after all option conformance
	changes have taken place in ahd_devlimited_syncrate.
	Changes in options may change the final syncrate we
	accept.

	Keep a copy of the hs_mailbox in our softc so that
	we can perform read/modify/write operations on the
	hs_mailbox without having to pause the sequencer to
	read the last written value.  Use the ENINT_COALESS
	flag in the hs_mailbox to toggle interrupt coalessing.

	Add entrypoints for enabling interrupt coalessing and
	setting both a timeout (how long to wait for commands
	to be coalessed) and a maximum commands to coaless value.
	Add a statistics timer that decides when to enable or
	disable interrupt coalessing based on load.

	Add a routine, ahd_reset_cmds_pending() which is used
	to update the CMDS_PENDING sequencer variable whenever
	error recovery compeltes SCBs without notifying the
	sequencer.  Since ahd_reset_cmds_pending is called
	during ahd_unpause() only if we've aborted SCBs, its
	call to ahd_flush_qoutfifo should not cause recursion
	through ahd_run_qoutfifo().  A panic has been added to
	ensure that this recursion does not occur.

	In ahd_search_qinfifo, update the CMDS_PENDING sequencer
	variable directly.  ahd_search_qinififo can be called
	in situations where using ahd_reset_cmds_pending() might
	cause recursion.  Since we can safely determine the
	exact number to reduce CMDS_PENDING by in this scenario
	without running the qoutfifo, the manual update is sufficient.

	Clean up diagnostics.
	Add ahd_flush_qoutfifo() which will run the qoutfifo
	as well as complete any commands sitting on the
	sequencer's COMPLETE_SCB lists or the good status FIFO.
	Use this routine in several places that did similar
	things in an add-hoc, but incomplete, fashion.  A call
	to this routine was also added to ahd_abort_scbs() to
	close a race.

	In ahd_pause_and_flushwork() only return once selections
	are safely disabled.  Flush all completed commands via
	ahd_flush_qoutfifo().

	Remove "Now packetized" diagnostic now that this
	information is incorperated into the actual negotiation
	messages that are displayed.

	When forcing renegotiation, don't clober the current
	ppr_options.  Much of the driver uses this information
	to determine if we are currently packetized or not.

	Remove some stray spaces at column 1 in ahd_set_tags.

	When complaining about getting a host message loop
	request with no pending messages, print out the
	SCB_CONTROL register down on the card.

	Modify the ahd_sent_msg() routine to handle a search
	for an outgoing identify message.  Use this to detect
	a msg reject on an identify message which typically
	indicates that the target thought we were packetized.
	Force a renegotiation in this case.

	In ahd_search_qinfifo(), wait more effectively for SCB
	DMA activities to cease.  We also disable SCB fetch
	operations since we are about to change the qinfifo
	and any fetch in progress will likely be invalidated.

	In ahd_qinfifo_count(), fix the qinfifo empty case.

	In ahd_dump_card_state(), print out CCSCBCTL in the
	correct mode.

	If we are a narrow controller, don't set the current
	width to unknown when forcing a future negotiation.
	This just confuses the code into attempting a wide
	negotiation on a narrow bus.

	Add support for task management function completions.

	Modify ahd_handle_devreset so that it can handle
	lun resets in addition to target resets.  Use
	ahd_handle_devreset for lun and target reset task
	management functions.

	Handle the abort task TMF race case better.  We now
	wait until any current selections are over and then
	set the TMF back to zero.  This should cause the sequencer
	to ignore the abort TMF completion should it occur.

	Correct a bug in the illegal phase handler that
	caused us to drop down to narrow when handling the
	unexpected command phase case after 3rd party
	reset of a packetized device.

	Indicate the features, bugs, and flags set in the softc
	that are used to control firmware patch download when
        booting verbose.

aic79xx.h:
	Add coalessing and HS_MAILBOX fields.

	Add per-softc variables for the stats "daemon".

	Add a debug option for interrupt coalessing activities.

	Add two new softc flags:
	o AHD_UPDATE_PEND_CMDS
	  Run ahd_reset_cmds_pending() on the next unpause.

	o AHD_RUNNING_QOUTFIFO
	  Used to catch recursion through ahd_run_qoutfifo().

aic79xx.reg:
	Correct register addresses related to the software timer
	and the DFDBCTL register.

	Add constants paramaterizing the software timer.

	Add scratch ram locations for storing interrupt coalessing
	tunables.

	Break INTMASK in SEQITNCTL out into INTMASK1 and INTMASK2.
	In at least the REV A, these are writable bits.  We make
	use of that for a swtimer workaround in the sequencer.

	Since HS_MAILBOX autoclears, provide a sequencer variable
	to store its contents.

	Add SEQINT codes for handling task management completions.

aic79xx.seq:
	Correct ignore wide residue processing check for
	a wide negotiation being in effect.  We must be
	in the SCSI register window in order to access the
	negotiation table.

	Use the software timer and a commands completed count to
	implement interrupt coalessing.  The command complete is
	deferred until either the maximum command threshold or a
	the expiration of a command deferral timer.  If we have
	more SCBs to complete to the host (sitting in COMPLETE_SCB
	lists), always try to coaless them up to our coalessing limit.
	If coalessing is enabled, but we have fewer commands oustanting
	than the host's min coalessing limit, complete the command
	immediately.

	Add code to track the number of commands outstanding.
	Commands are outstanding from the time they are placed
	into the execution queue until the DMA to post completion
	is setup.

	Add a workaround for intvec_2 interrupts on the H2A4.
	In H2A4, the mode pointer is not saved for intvec2, but
	is restored on iret.  This can lead to the restoration
	of a bogus mode ptr.  Manually clear the intmask bits and
	do a normal return to compensate.  We use intvec_2 to
	track interrupt coalessing timeouts.

	Since we cannot disable the swtimer's countdown, simply
	mask its interrupt once we no longer care about it firing.

	In idle_loop_cchan, update LOCAL_HS_MAILBOX everytime
	we are notified of an HS_MAILBOX update via the
	HS_MAILBOX_ACT bit in QOFF_CTLSTA.  We have to use a
	local copy of persistant portions of the HS_MAILBOX as
	the mailbox auto-clears on any read.

	Move the test for the cfg4istat interrupt up an instruction
	to hopefully close a race between the next outgoing selection
	and our disabling of selections.

	Add a missing ret to the last instruction in load_overrun_buf.

	Add notifications to the host of task management
	completions as well as the completions for commands
	that completed successfully before their corresponding
	TMF could be sent.

	Hold a critical section during select-out processing
	until we have a fully identified connection.  This
	removes a race condition with the legacy abort handler.

	Correct a few spelling errors in some comments.

aic79xx_inline.h:
	Call ahd_reset_cmds_pending() in ahd_unpause if required.

	Update cmdcmplt interrupt statistics in our interrupt
	handler.

	Allow callers to ahd_send_scb() to set the task management
	function.

aic79xx_pci.c:
	Disable SERR and pause the controller prior to performing
	our mmapped I/O test.  The U320 controllers do not support
	"auto-access-pause".

aic79xx_osm.c:
	Set the task management function now that
	ahd_send_scb() doesn't do it for us.  We
	also perform a lun reset in response to BDR
	requests to packetized devices.
2003-01-20 20:17:35 +00:00

924 lines
25 KiB
C
Raw Blame History

/*
* Product specific probe and attach routines for:
* aic7901 and aic7902 SCSI controllers
*
* Copyright (c) 1994-2001 Justin T. Gibbs.
* Copyright (c) 2000-2002 Adaptec Inc.
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions, and the following disclaimer,
* without modification.
* 2. Redistributions in binary form must reproduce at minimum a disclaimer
* substantially similar to the "NO WARRANTY" disclaimer below
* ("Disclaimer") and any redistribution must be conditioned upon
* including a substantially similar Disclaimer requirement for further
* binary redistribution.
* 3. Neither the names of the above-listed copyright holders nor the names
* of any contributors may be used to endorse or promote products derived
* from this software without specific prior written permission.
*
* Alternatively, this software may be distributed under the terms of the
* GNU General Public License ("GPL") version 2 as published by the Free
* Software Foundation.
*
* NO WARRANTY
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR
* A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
* HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
* OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
* STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING
* IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGES.
*
* $Id: //depot/aic7xxx/aic7xxx/aic79xx_pci.c#61 $
*
* $FreeBSD$
*/
#ifdef __linux__
#include "aic79xx_osm.h"
#include "aic79xx_inline.h"
#else
#include <dev/aic7xxx/aic79xx_osm.h>
#include <dev/aic7xxx/aic79xx_inline.h>
#endif
static __inline uint64_t
ahd_compose_id(u_int device, u_int vendor, u_int subdevice, u_int subvendor)
{
uint64_t id;
id = subvendor
| (subdevice << 16)
| ((uint64_t)vendor << 32)
| ((uint64_t)device << 48);
return (id);
}
#define ID_ALL_MASK 0xFFFFFFFFFFFFFFFFull
#define ID_DEV_VENDOR_MASK 0xFFFFFFFF00000000ull
#define ID_9005_GENERIC_MASK 0xFFF0FFFF00000000ull
#define ID_AIC7901 0x800F9005FFFF9005ull
#define ID_AIC7901A 0x801E9005FFFF9005ull
#define ID_AIC7901A_IROC 0x809E9005FFFF9005ull
#define ID_AHA_29320A 0x8000900500609005ull
#define ID_AHA_29320LP 0x8014900500449005ull
#define ID_AHA_29320LP_IROC 0x8094900500449005ull
#define ID_AIC7902 0x801F9005FFFF9005ull
#define ID_AIC7902_IROC 0x809F9005FFFF9005ull
#define ID_AIC7902_B 0x801D9005FFFF9005ull
#define ID_AIC7902_B_IROC 0x809D9005FFFF9005ull
#define ID_AHA_39320 0x8010900500409005ull
#define ID_AHA_39320D 0x8011900500419005ull
#define ID_AHA_39320D_B 0x801C900500419005ull
#define ID_AHA_39320D_HP 0x8011900500AC0E11ull
#define ID_AHA_39320D_B_HP 0x801C900500AC0E11ull
#define ID_AHA_29320 0x8012900500429005ull
#define ID_AHA_29320B 0x8013900500439005ull
#define ID_AIC7902_PCI_REV_A4 0x3
#define ID_AIC7902_PCI_REV_B0 0x10
#define SUBID_HP 0x0E11
#define DEVID_9005_TYPE(id) ((id) & 0xF)
#define DEVID_9005_TYPE_HBA 0x0 /* Standard Card */
#define DEVID_9005_TYPE_HBA_2EXT 0x1 /* 2 External Ports */
#define DEVID_9005_TYPE_IROC 0x8 /* Raid(0,1,10) Card */
#define DEVID_9005_TYPE_MB 0xF /* On Motherboard */
#define DEVID_9005_MFUNC(id) ((id) & 0x10)
#define DEVID_9005_PACKETIZED(id) ((id) & 0x8000)
#define SUBID_9005_TYPE(id) ((id) & 0xF)
#define SUBID_9005_TYPE_HBA 0x0 /* Standard Card */
#define SUBID_9005_TYPE_MB 0xF /* On Motherboard */
#define SUBID_9005_AUTOTERM(id) (((id) & 0x10) == 0)
#define SUBID_9005_LEGACYCONN_FUNC(id) ((id) & 0x20)
#define SUBID_9005_SEEPTYPE(id) ((id) & 0x0C0) >> 6)
#define SUBID_9005_SEEPTYPE_NONE 0x0
#define SUBID_9005_SEEPTYPE_4K 0x1
static ahd_device_setup_t ahd_aic7901A_setup;
static ahd_device_setup_t ahd_aic7902_setup;
struct ahd_pci_identity ahd_pci_ident_table [] =
{
/* aic7901A based controllers */
{
ID_AHA_29320LP,
ID_ALL_MASK,
"Adaptec 29320LP Ultra320 SCSI adapter",
ahd_aic7901A_setup
},
{
ID_AHA_29320A,
ID_ALL_MASK,
"Adaptec 29320A Ultra320 SCSI adapter",
ahd_aic7901A_setup
},
/* aic7902 based controllers */
{
ID_AHA_39320,
ID_ALL_MASK,
"Adaptec 39320 Ultra320 SCSI adapter",
ahd_aic7902_setup
},
{
ID_AHA_39320D,
ID_ALL_MASK,
"Adaptec 39320D Ultra320 SCSI adapter",
ahd_aic7902_setup
},
{
ID_AHA_39320D_HP,
ID_ALL_MASK,
"Adaptec (HP OEM) 39320D Ultra320 SCSI adapter",
ahd_aic7902_setup
},
{
ID_AHA_39320D_B,
ID_ALL_MASK,
"Adaptec 39320D Ultra320 SCSI adapter",
ahd_aic7902_setup
},
{
ID_AHA_39320D_B_HP,
ID_ALL_MASK,
"Adaptec (HP OEM) 39320D Ultra320 SCSI adapter",
ahd_aic7902_setup
},
{
ID_AHA_29320,
ID_ALL_MASK,
"Adaptec 29320 Ultra320 SCSI adapter",
ahd_aic7902_setup
},
{
ID_AHA_29320B,
ID_ALL_MASK,
"Adaptec 29320B Ultra320 SCSI adapter",
ahd_aic7902_setup
},
/* Generic chip probes for devices we don't know 'exactly' */
{
ID_AIC7901A & ID_DEV_VENDOR_MASK,
ID_DEV_VENDOR_MASK,
"Adaptec AIC7901A Ultra320 SCSI adapter",
ahd_aic7901A_setup
},
{
ID_AIC7902 & ID_9005_GENERIC_MASK,
ID_9005_GENERIC_MASK,
"Adaptec AIC7902 Ultra320 SCSI adapter",
ahd_aic7902_setup
}
};
const u_int ahd_num_pci_devs = NUM_ELEMENTS(ahd_pci_ident_table);
#define DEVCONFIG 0x40
#define PCIXINITPAT 0x0000E000ul
#define PCIXINIT_PCI33_66 0x0000E000ul
#define PCIXINIT_PCIX50_66 0x0000C000ul
#define PCIXINIT_PCIX66_100 0x0000A000ul
#define PCIXINIT_PCIX100_133 0x00008000ul
#define PCI_BUS_MODES_INDEX(devconfig) \
(((devconfig) & PCIXINITPAT) >> 13)
static const char *pci_bus_modes[] =
{
"PCI bus mode unknown",
"PCI bus mode unknown",
"PCI bus mode unknown",
"PCI bus mode unknown",
"PCI-X 101-133Mhz",
"PCI-X 67-100Mhz",
"PCI-X 50-66Mhz",
"PCI 33 or 66Mhz"
};
#define TESTMODE 0x00000800ul
#define IRDY_RST 0x00000200ul
#define FRAME_RST 0x00000100ul
#define PCI64BIT 0x00000080ul
#define MRDCEN 0x00000040ul
#define ENDIANSEL 0x00000020ul
#define MIXQWENDIANEN 0x00000008ul
#define DACEN 0x00000004ul
#define STPWLEVEL 0x00000002ul
#define QWENDIANSEL 0x00000001ul
#define DEVCONFIG1 0x44
#define PREQDIS 0x01
#define CSIZE_LATTIME 0x0c
#define CACHESIZE 0x000000fful
#define LATTIME 0x0000ff00ul
static int ahd_check_extport(struct ahd_softc *ahd);
static void ahd_configure_termination(struct ahd_softc *ahd,
u_int adapter_control);
static void ahd_pci_split_intr(struct ahd_softc *ahd, u_int intstat);
struct ahd_pci_identity *
ahd_find_pci_device(ahd_dev_softc_t pci)
{
uint64_t full_id;
uint16_t device;
uint16_t vendor;
uint16_t subdevice;
uint16_t subvendor;
struct ahd_pci_identity *entry;
u_int i;
vendor = ahd_pci_read_config(pci, PCIR_DEVVENDOR, /*bytes*/2);
device = ahd_pci_read_config(pci, PCIR_DEVICE, /*bytes*/2);
subvendor = ahd_pci_read_config(pci, PCIR_SUBVEND_0, /*bytes*/2);
subdevice = ahd_pci_read_config(pci, PCIR_SUBDEV_0, /*bytes*/2);
full_id = ahd_compose_id(device,
vendor,
subdevice,
subvendor);
for (i = 0; i < ahd_num_pci_devs; i++) {
entry = &ahd_pci_ident_table[i];
if (entry->full_id == (full_id & entry->id_mask)) {
/* Honor exclusion entries. */
if (entry->name == NULL)
return (NULL);
return (entry);
}
}
return (NULL);
}
int
ahd_pci_config(struct ahd_softc *ahd, struct ahd_pci_identity *entry)
{
struct scb_data *shared_scb_data;
u_long l;
u_int command;
uint32_t devconfig;
uint16_t subvendor;
int error;
shared_scb_data = NULL;
ahd->description = entry->name;
/*
* Record if this is an HP board.
*/
subvendor = ahd_pci_read_config(ahd->dev_softc,
PCIR_SUBVEND_0, /*bytes*/2);
if (subvendor == SUBID_HP)
ahd->flags |= AHD_HP_BOARD;
error = entry->setup(ahd);
if (error != 0)
return (error);
devconfig = ahd_pci_read_config(ahd->dev_softc, DEVCONFIG, /*bytes*/4);
if ((devconfig & PCIXINITPAT) == PCIXINIT_PCI33_66) {
ahd->chip |= AHD_PCI;
/* Disable PCIX workarounds when running in PCI mode. */
ahd->bugs &= ~AHD_PCIX_BUG_MASK;
} else {
ahd->chip |= AHD_PCIX;
}
ahd->bus_description = pci_bus_modes[PCI_BUS_MODES_INDEX(devconfig)];
ahd_power_state_change(ahd, AHD_POWER_STATE_D0);
error = ahd_pci_map_registers(ahd);
if (error != 0)
return (error);
/*
* If we need to support high memory, enable dual
* address cycles. This bit must be set to enable
* high address bit generation even if we are on a
* 64bit bus (PCI64BIT set in devconfig).
*/
if ((ahd->flags & (AHD_39BIT_ADDRESSING|AHD_64BIT_ADDRESSING)) != 0) {
uint32_t devconfig;
if (bootverbose)
printf("%s: Enabling 39Bit Addressing\n",
ahd_name(ahd));
devconfig = ahd_pci_read_config(ahd->dev_softc,
DEVCONFIG, /*bytes*/4);
devconfig |= DACEN;
ahd_pci_write_config(ahd->dev_softc, DEVCONFIG,
devconfig, /*bytes*/4);
}
/* Ensure busmastering is enabled */
command = ahd_pci_read_config(ahd->dev_softc, PCIR_COMMAND, /*bytes*/1);
command |= PCIM_CMD_BUSMASTEREN;
ahd_pci_write_config(ahd->dev_softc, PCIR_COMMAND, command, /*bytes*/1);
error = ahd_softc_init(ahd);
if (error != 0)
return (error);
ahd->bus_intr = ahd_pci_intr;
error = ahd_reset(ahd);
if (error != 0)
return (ENXIO);
ahd->pci_cachesize =
ahd_pci_read_config(ahd->dev_softc, CSIZE_LATTIME,
/*bytes*/1) & CACHESIZE;
ahd->pci_cachesize *= 4;
ahd_set_modes(ahd, AHD_MODE_SCSI, AHD_MODE_SCSI);
/* See if we have a SEEPROM and perform auto-term */
error = ahd_check_extport(ahd);
if (error != 0)
return (error);
/* Core initialization */
error = ahd_init(ahd);
if (error != 0)
return (error);
/*
* Allow interrupts now that we are completely setup.
*/
error = ahd_pci_map_int(ahd);
if (error != 0)
return (error);
ahd_list_lock(&l);
/*
* Link this softc in with all other ahd instances.
*/
ahd_softc_insert(ahd);
ahd_list_unlock(&l);
return (0);
}
/*
* Perform some simple tests that should catch situations where
* our registers are invalidly mapped.
*/
int
ahd_pci_test_register_access(struct ahd_softc *ahd)
{
ahd_mode_state saved_modes;
uint32_t cmd;
int error;
uint8_t hcntrl;
saved_modes = ahd_save_modes(ahd);
error = EIO;
/*
* Enable PCI error interrupt status, but suppress NMIs
* generated by SERR raised due to target aborts.
*/
cmd = ahd_pci_read_config(ahd->dev_softc, PCIR_COMMAND, /*bytes*/2);
ahd_pci_write_config(ahd->dev_softc, PCIR_COMMAND,
cmd & ~PCIM_CMD_SERRESPEN, /*bytes*/2);
/*
* First a simple test to see if any
* registers can be read. Reading
* HCNTRL has no side effects and has
* at least one bit that is guaranteed to
* be zero so it is a good register to
* use for this test.
*/
hcntrl = ahd_inb(ahd, HCNTRL);
if (hcntrl == 0xFF)
goto fail;
/*
* Next create a situation where write combining
* or read prefetching could be initiated by the
* CPU or host bridge. Our device does not support
* either, so look for data corruption and/or flaged
* PCI errors.
*/
ahd_outb(ahd, HCNTRL, hcntrl|PAUSE);
while (ahd_is_paused(ahd) == 0)
;
ahd_outb(ahd, SEQCTL0, PERRORDIS);
ahd_outl(ahd, SRAM_BASE, 0x5aa555aa);
if (ahd_inl(ahd, SRAM_BASE) != 0x5aa555aa)
goto fail;
if ((ahd_inb(ahd, INTSTAT) & PCIINT) != 0) {
u_int targpcistat;
ahd_set_modes(ahd, AHD_MODE_CFG, AHD_MODE_CFG);
targpcistat = ahd_inb(ahd, TARGPCISTAT);
if ((targpcistat & STA) != 0)
goto fail;
}
error = 0;
fail:
if ((ahd_inb(ahd, INTSTAT) & PCIINT) != 0) {
u_int targpcistat;
u_int pci_status1;
ahd_set_modes(ahd, AHD_MODE_CFG, AHD_MODE_CFG);
targpcistat = ahd_inb(ahd, TARGPCISTAT);
/* Silently clear any latched errors. */
ahd_outb(ahd, TARGPCISTAT, targpcistat);
pci_status1 = ahd_pci_read_config(ahd->dev_softc,
PCIR_STATUS + 1, /*bytes*/1);
ahd_pci_write_config(ahd->dev_softc, PCIR_STATUS + 1,
pci_status1, /*bytes*/1);
ahd_outb(ahd, CLRINT, CLRPCIINT);
}
ahd_restore_modes(ahd, saved_modes);
ahd_outb(ahd, SEQCTL0, PERRORDIS|FAILDIS);
ahd_pci_write_config(ahd->dev_softc, PCIR_COMMAND, cmd, /*bytes*/2);
return (error);
}
/*
* Check the external port logic for a serial eeprom
* and termination/cable detection contrls.
*/
static int
ahd_check_extport(struct ahd_softc *ahd)
{
struct seeprom_config *sc;
u_int adapter_control;
int have_seeprom;
int error;
sc = ahd->seep_config;
have_seeprom = ahd_acquire_seeprom(ahd);
if (have_seeprom) {
u_int start_addr;
if (bootverbose)
printf("%s: Reading SEEPROM...", ahd_name(ahd));
/* Address is always in units of 16bit words */
start_addr = (sizeof(*sc) / 2) * (ahd->channel - 'A');
error = ahd_read_seeprom(ahd, (uint16_t *)sc,
start_addr, sizeof(*sc)/2);
if (error != 0) {
printf("Unable to read SEEPROM\n");
have_seeprom = 0;
} else {
have_seeprom = ahd_verify_cksum(sc);
if (bootverbose) {
if (have_seeprom == 0)
printf ("checksum error\n");
else
printf ("done.\n");
}
}
ahd_release_seeprom(ahd);
}
if (!have_seeprom) {
u_int nvram_scb;
/*
* Pull scratch ram settings and treat them as
* if they are the contents of an seeprom if
* the 'ADPT', 'BIOS', or 'ASPI' signature is found
* in SCB 0xFF. We manually compose the data as 16bit
* values to avoid endian issues.
*/
ahd_set_scbptr(ahd, 0xFF);
nvram_scb = ahd_inb_scbram(ahd, SCB_BASE + NVRAM_SCB_OFFSET);
if (nvram_scb != 0xFF
&& ((ahd_inb_scbram(ahd, SCB_BASE + 0) == 'A'
&& ahd_inb_scbram(ahd, SCB_BASE + 1) == 'D'
&& ahd_inb_scbram(ahd, SCB_BASE + 2) == 'P'
&& ahd_inb_scbram(ahd, SCB_BASE + 3) == 'T')
|| (ahd_inb_scbram(ahd, SCB_BASE + 0) == 'B'
&& ahd_inb_scbram(ahd, SCB_BASE + 1) == 'I'
&& ahd_inb_scbram(ahd, SCB_BASE + 2) == 'O'
&& ahd_inb_scbram(ahd, SCB_BASE + 3) == 'S')
|| (ahd_inb_scbram(ahd, SCB_BASE + 0) == 'A'
&& ahd_inb_scbram(ahd, SCB_BASE + 1) == 'S'
&& ahd_inb_scbram(ahd, SCB_BASE + 2) == 'P'
&& ahd_inb_scbram(ahd, SCB_BASE + 3) == 'I'))) {
uint16_t *sc_data;
int i;
ahd_set_scbptr(ahd, nvram_scb);
sc_data = (uint16_t *)sc;
for (i = 0; i < 64; i += 2)
*sc_data++ = ahd_inw_scbram(ahd, SCB_BASE+i);
have_seeprom = ahd_verify_cksum(sc);
if (have_seeprom)
ahd->flags |= AHD_SCB_CONFIG_USED;
}
}
#if AHD_DEBUG
if (have_seeprom != 0
&& (ahd_debug & AHD_DUMP_SEEPROM) != 0) {
uint8_t *sc_data;
int i;
printf("%s: Seeprom Contents:", ahd_name(ahd));
sc_data = (uint8_t *)sc;
for (i = 0; i < (sizeof(*sc)); i += 2)
printf("\n\t0x%.4x",
sc_data[i] | (sc_data[i+1] << 8));
printf("\n");
}
#endif
if (!have_seeprom) {
if (bootverbose)
printf("%s: No SEEPROM available.\n", ahd_name(ahd));
ahd->flags |= AHD_USEDEFAULTS;
error = ahd_default_config(ahd);
adapter_control = CFAUTOTERM|CFSEAUTOTERM;
free(ahd->seep_config, M_DEVBUF);
ahd->seep_config = NULL;
} else {
error = ahd_parse_cfgdata(ahd, sc);
adapter_control = sc->adapter_control;
}
if (error != 0)
return (error);
ahd_configure_termination(ahd, adapter_control);
return (0);
}
static void
ahd_configure_termination(struct ahd_softc *ahd, u_int adapter_control)
{
int error;
u_int sxfrctl1;
uint8_t termctl;
uint32_t devconfig;
devconfig = ahd_pci_read_config(ahd->dev_softc, DEVCONFIG, /*bytes*/4);
devconfig &= ~STPWLEVEL;
if ((ahd->flags & AHD_STPWLEVEL_A) != 0)
devconfig |= STPWLEVEL;
if (bootverbose)
printf("%s: STPWLEVEL is %s\n",
ahd_name(ahd), (devconfig & STPWLEVEL) ? "on" : "off");
ahd_pci_write_config(ahd->dev_softc, DEVCONFIG, devconfig, /*bytes*/4);
/* Make sure current sensing is off. */
if ((ahd->flags & AHD_CURRENT_SENSING) != 0) {
(void)ahd_write_flexport(ahd, FLXADDR_ROMSTAT_CURSENSECTL, 0);
}
/*
* Read to sense. Write to set.
*/
error = ahd_read_flexport(ahd, FLXADDR_TERMCTL, &termctl);
if ((adapter_control & CFAUTOTERM) == 0) {
if (bootverbose)
printf("%s: Manual Primary Termination\n",
ahd_name(ahd));
termctl &= ~(FLX_TERMCTL_ENPRILOW|FLX_TERMCTL_ENPRIHIGH);
if ((adapter_control & CFSTERM) != 0)
termctl |= FLX_TERMCTL_ENPRILOW;
if ((adapter_control & CFWSTERM) != 0)
termctl |= FLX_TERMCTL_ENPRIHIGH;
} else if (error != 0) {
printf("%s: Primary Auto-Term Sensing failed! "
"Using Defaults.\n", ahd_name(ahd));
termctl = FLX_TERMCTL_ENPRILOW|FLX_TERMCTL_ENPRIHIGH;
}
if ((adapter_control & CFSEAUTOTERM) == 0) {
if (bootverbose)
printf("%s: Manual Secondary Termination\n",
ahd_name(ahd));
termctl &= ~(FLX_TERMCTL_ENSECLOW|FLX_TERMCTL_ENSECHIGH);
if ((adapter_control & CFSELOWTERM) != 0)
termctl |= FLX_TERMCTL_ENSECLOW;
if ((adapter_control & CFSEHIGHTERM) != 0)
termctl |= FLX_TERMCTL_ENSECHIGH;
} else if (error != 0) {
printf("%s: Secondary Auto-Term Sensing failed! "
"Using Defaults.\n", ahd_name(ahd));
termctl |= FLX_TERMCTL_ENSECLOW|FLX_TERMCTL_ENSECHIGH;
}
/*
* Now set the termination based on what we found.
*/
sxfrctl1 = ahd_inb(ahd, SXFRCTL1) & ~STPWEN;
if ((termctl & FLX_TERMCTL_ENPRILOW) != 0) {
ahd->flags |= AHD_TERM_ENB_A;
sxfrctl1 |= STPWEN;
}
/* Must set the latch once in order to be effective. */
ahd_outb(ahd, SXFRCTL1, sxfrctl1|STPWEN);
ahd_outb(ahd, SXFRCTL1, sxfrctl1);
error = ahd_write_flexport(ahd, FLXADDR_TERMCTL, termctl);
if (error != 0) {
printf("%s: Unable to set termination settings!\n",
ahd_name(ahd));
} else if (bootverbose) {
printf("%s: Primary High byte termination %sabled\n",
ahd_name(ahd),
(termctl & FLX_TERMCTL_ENPRIHIGH) ? "En" : "Dis");
printf("%s: Primary Low byte termination %sabled\n",
ahd_name(ahd),
(termctl & FLX_TERMCTL_ENPRILOW) ? "En" : "Dis");
printf("%s: Secondary High byte termination %sabled\n",
ahd_name(ahd),
(termctl & FLX_TERMCTL_ENSECHIGH) ? "En" : "Dis");
printf("%s: Secondary Low byte termination %sabled\n",
ahd_name(ahd),
(termctl & FLX_TERMCTL_ENSECLOW) ? "En" : "Dis");
}
return;
}
#define DPE 0x80
#define SSE 0x40
#define RMA 0x20
#define RTA 0x10
#define STA 0x08
#define DPR 0x01
static const char *split_status_source[] =
{
"DFF0",
"DFF1",
"OVLY",
"CMC",
};
static const char *pci_status_source[] =
{
"DFF0",
"DFF1",
"SG",
"CMC",
"OVLY",
"NONE",
"MSI",
"TARG"
};
static const char *split_status_strings[] =
{
"%s: Received split response in %s.\n"
"%s: Received split completion error message in %s\n",
"%s: Receive overrun in %s\n",
"%s: Count not complete in %s\n",
"%s: Split completion data bucket in %s\n",
"%s: Split completion address error in %s\n",
"%s: Split completion byte count error in %s\n",
"%s: Signaled Target-abort to early terminate a split in %s\n",
};
static const char *pci_status_strings[] =
{
"%s: Data Parity Error has been reported via PERR# in %s\n",
"%s: Target initial wait state error in %s\n",
"%s: Split completion read data parity error in %s\n",
"%s: Split completion address attribute parity error in %s\n",
"%s: Received a Target Abort in %s\n",
"%s: Received a Master Abort in %s\n",
"%s: Signal System Error Detected in %s\n",
"%s: Address or Write Phase Parity Error Detected in %s.\n"
};
void
ahd_pci_intr(struct ahd_softc *ahd)
{
uint8_t pci_status[8];
ahd_mode_state saved_modes;
u_int pci_status1;
u_int intstat;
u_int i;
u_int reg;
intstat = ahd_inb(ahd, INTSTAT);
if ((intstat & SPLTINT) != 0)
ahd_pci_split_intr(ahd, intstat);
if ((intstat & PCIINT) == 0)
return;
printf("%s: PCI error Interrupt\n", ahd_name(ahd));
saved_modes = ahd_save_modes(ahd);
ahd_dump_card_state(ahd);
ahd_set_modes(ahd, AHD_MODE_CFG, AHD_MODE_CFG);
for (i = 0, reg = DF0PCISTAT; i < 8; i++, reg++) {
if (i == 5)
continue;
pci_status[i] = ahd_inb(ahd, reg);
/* Clear latched errors. So our interupt deasserts. */
ahd_outb(ahd, reg, pci_status[i]);
}
for (i = 0; i < 8; i++) {
u_int bit;
if (i == 5)
continue;
for (bit = 0; bit < 8; bit++) {
if ((pci_status[i] & (0x1 << bit)) != 0) {
static const char *s;
s = pci_status_strings[bit];
if (i == 7/*TARG*/ && bit == 3)
s = "%s: Signaled Target Abort\n";
printf(s, ahd_name(ahd), pci_status_source[i]);
}
}
}
pci_status1 = ahd_pci_read_config(ahd->dev_softc,
PCIR_STATUS + 1, /*bytes*/1);
ahd_pci_write_config(ahd->dev_softc, PCIR_STATUS + 1,
pci_status1, /*bytes*/1);
ahd_restore_modes(ahd, saved_modes);
ahd_outb(ahd, CLRINT, CLRPCIINT);
ahd_unpause(ahd);
}
static void
ahd_pci_split_intr(struct ahd_softc *ahd, u_int intstat)
{
uint8_t split_status[4];
uint8_t split_status1[4];
uint8_t sg_split_status[2];
uint8_t sg_split_status1[2];
ahd_mode_state saved_modes;
u_int i;
uint16_t pcix_status;
/*
* Check for splits in all modes. Modes 0 and 1
* additionally have SG engine splits to look at.
*/
pcix_status = ahd_pci_read_config(ahd->dev_softc, PCIXR_STATUS,
/*bytes*/2);
printf("%s: PCI Split Interrupt - PCI-X status = 0x%x\n",
ahd_name(ahd), pcix_status);
saved_modes = ahd_save_modes(ahd);
for (i = 0; i < 4; i++) {
ahd_set_modes(ahd, i, i);
split_status[i] = ahd_inb(ahd, DCHSPLTSTAT0);
split_status1[i] = ahd_inb(ahd, DCHSPLTSTAT1);
/* Clear latched errors. So our interupt deasserts. */
ahd_outb(ahd, DCHSPLTSTAT0, split_status[i]);
ahd_outb(ahd, DCHSPLTSTAT1, split_status1[i]);
if (i != 0)
continue;
sg_split_status[i] = ahd_inb(ahd, SGSPLTSTAT0);
sg_split_status1[i] = ahd_inb(ahd, SGSPLTSTAT1);
/* Clear latched errors. So our interupt deasserts. */
ahd_outb(ahd, SGSPLTSTAT0, sg_split_status[i]);
ahd_outb(ahd, SGSPLTSTAT1, sg_split_status1[i]);
}
for (i = 0; i < 4; i++) {
u_int bit;
for (bit = 0; bit < 8; bit++) {
if ((split_status[i] & (0x1 << bit)) != 0) {
static const char *s;
s = split_status_strings[bit];
printf(s, ahd_name(ahd),
split_status_source[i]);
}
if (i != 0)
continue;
if ((sg_split_status[i] & (0x1 << bit)) != 0) {
static const char *s;
s = split_status_strings[bit];
printf(s, ahd_name(ahd), "SG");
}
}
}
/*
* Clear PCI-X status bits.
*/
ahd_pci_write_config(ahd->dev_softc, PCIXR_STATUS,
pcix_status, /*bytes*/2);
ahd_outb(ahd, CLRINT, CLRSPLTINT);
ahd_restore_modes(ahd, saved_modes);
}
static int
ahd_aic7901A_setup(struct ahd_softc *ahd)
{
int error;
error = ahd_aic7902_setup(ahd);
if (error != 0)
return (error);
ahd->chip = AHD_AIC7901A;
return (0);
}
static int
ahd_aic7902_setup(struct ahd_softc *ahd)
{
ahd_dev_softc_t pci;
u_int rev;
pci = ahd->dev_softc;
rev = ahd_pci_read_config(pci, PCIR_REVID, /*bytes*/1);
if (rev < ID_AIC7902_PCI_REV_A4) {
printf("%s: Unable to attach to unsupported chip revision %d\n",
ahd_name(ahd), rev);
ahd_pci_write_config(pci, PCIR_COMMAND, 0, /*bytes*/1);
return (ENXIO);
}
ahd->channel = ahd_get_pci_function(pci) + 'A';
ahd->chip = AHD_AIC7902;
ahd->features = AHD_AIC7902_FE;
if (rev < ID_AIC7902_PCI_REV_B0) {
/*
* Enable A series workarounds.
*/
ahd->bugs |= AHD_SENT_SCB_UPDATE_BUG|AHD_ABORT_LQI_BUG
| AHD_PKT_BITBUCKET_BUG|AHD_LONG_SETIMO_BUG
| AHD_NLQICRC_DELAYED_BUG|AHD_SCSIRST_BUG
| AHD_LQO_ATNO_BUG|AHD_AUTOFLUSH_BUG
| AHD_CLRLQO_AUTOCLR_BUG|AHD_PCIX_MMAPIO_BUG
| AHD_PCIX_CHIPRST_BUG|AHD_PKTIZED_STATUS_BUG
| AHD_PKT_LUN_BUG|AHD_MDFF_WSCBPTR_BUG
| AHD_REG_SLOW_SETTLE_BUG|AHD_SET_MODE_BUG
| AHD_BUSFREEREV_BUG|AHD_NONPACKFIFO_BUG
| AHD_PACED_NEGTABLE_BUG;
/*
* IO Cell paramter setup.
*/
AHD_SET_PRECOMP(ahd, AHD_PRECOMP_CUTBACK_29);
if ((ahd->flags & AHD_HP_BOARD) == 0)
AHD_SET_SLEWRATE(ahd, AHD_SLEWRATE_DEF_REVA);
} else {
u_int devconfig1;
ahd->features |= AHD_RTI|AHD_NEW_IOCELL_OPTS
| AHD_NEW_DFCNTRL_OPTS;
ahd->bugs |= AHD_LQOOVERRUN_BUG|AHD_ABORT_LQI_BUG
| AHD_INTCOLLISION_BUG;
/*
* IO Cell paramter setup.
*/
AHD_SET_PRECOMP(ahd, AHD_PRECOMP_CUTBACK_29);
AHD_SET_SLEWRATE(ahd, AHD_SLEWRATE_DEF_REVB);
AHD_SET_AMPLITUDE(ahd, AHD_AMPLITUDE_DEF);
/*
* Set the PREQDIS bit for H2B which disables some workaround
* that doesn't work on regular PCI busses.
* XXX - Find out exactly what this does from the hardware
* folks!
*/
devconfig1 = ahd_pci_read_config(pci, DEVCONFIG1, /*bytes*/1);
ahd_pci_write_config(pci, DEVCONFIG1,
devconfig1|PREQDIS, /*bytes*/1);
devconfig1 = ahd_pci_read_config(pci, DEVCONFIG1, /*bytes*/1);
}
return (0);
}
Reference in New Issue View Git Blame Copy Permalink