1
0
mirror of https://git.FreeBSD.org/src.git synced 2024-12-24 11:29:10 +00:00
freebsd/sys/i386/isa/if_cx.c
Peter Wemm f71c01cc52 Borrow phk's axe and apply the next stage of config(8)'s evolution.
Use Warner Losh's "hint" driver to decode ascii strings to fill the
resource table at boot time.

config(8) no longer generates an ioconf.c table - ie: the configuration
no longer has to be compiled into the kernel.  You can reconfigure your
isa devices with the likes of this at loader(8) time:
  set hint.ed.0.port=0x320

userconfig will be rewritten to use this style interface one day and will
move to /boot/userconfig.4th or something like that.

It is still possible to statically compile in a set of hints into a kernel
if you do not wish to use loader(8).  See the "hints" directive in GENERIC
as an example.

All device wiring has been moved out of config(8).  There is a set of
helper scripts (see i386/conf/gethints.pl, and the same for alpha and pc98)
that extract the 'at isa? port foo irq bar' from the old files and produces
a hints file.  If you install this file as /boot/device.hints (and update
/boot/defaults/loader.conf - You can do a build/install in sys/boot) then
loader will load it automatically for you.  You can also compile in the
hints directly with:  hints "device.hints"  as well.

There are a few things that I'm not too happy with yet.  Under this scheme,
things like LINT would no longer be useful as "documentation" of settings.
I have renamed this file to 'NOTES' and stored the example hints strings
in it.  However... this is not something that config(8) understands, so
there is a script that extracts the build-specific data from the
documentation file (NOTES) to produce a LINT that can be config'ed and
built.  A stack of man4 pages will need updating. :-/

Also, since there is no longer a difference between 'device' and
'pseudo-device' I collapsed the two together, and the resulting 'device'
takes a 'number of units' for devices that still have it statically
allocated.  eg:  'device fe 4' will compile the fe driver with NFE set
to 4.  You can then set hints for 4 units (0 - 3).  Also note that
'device fe0' will be interpreted as "zero units of 'fe'" which would be
bad, so there is a config warning for this.  This is only needed for
old drivers that still have static limits on numbers of units.
All the statically limited drivers that I could find were marked.

Please exercise EXTREME CAUTION when transitioning!

Moral support by: phk, msmith, dfr, asmodai, imp, and others
2000-06-13 22:28:50 +00:00

834 lines
20 KiB
C

/*
* Cronyx-Sigma adapter driver for FreeBSD.
* Supports PPP/HDLC and Cisco/HDLC protocol in synchronous mode,
* and asyncronous channels with full modem control.
* Keepalive protocol implemented in both Cisco and PPP modes.
*
* Copyright (C) 1994 Cronyx Ltd.
* Author: Serge Vakulenko, <vak@zebub.msk.su>
*
* This software is distributed with NO WARRANTIES, not even the implied
* warranties for MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
*
* Authors grant any other persons or organisations permission to use
* or modify this software as long as this message is kept with the software,
* all derivative works or modified versions.
*
* Version 1.9, Wed Oct 4 18:58:15 MSK 1995
*
* $FreeBSD$
*
*/
#undef DEBUG
#include "cx.h"
#include <sys/param.h>
#include <sys/systm.h>
#include <sys/kernel.h>
#include <sys/malloc.h>
#include <sys/mbuf.h>
#include <sys/sockio.h>
#include <sys/socket.h>
#include <sys/conf.h>
#include <sys/bus.h>
#include <net/if.h>
#include <net/bpf.h>
#include <i386/isa/isa_device.h>
#ifndef COMPAT_OLDISA
#error "The cx device requires the old isa compatibility shims"
#endif
#define watchdog_func_t void(*)(struct ifnet *)
#define start_func_t void(*)(struct ifnet*)
#include <net/if_sppp.h>
#include <machine/cronyx.h>
#include <i386/isa/cxreg.h>
/* XXX exported. */
void cxswitch (cx_chan_t *c, cx_soft_opt_t new);
static int cxprobe __P((struct isa_device *id));
static int cxattach __P((struct isa_device *id));
static void cxput __P((cx_chan_t *c, char b));
static void cxsend __P((cx_chan_t *c));
static void cxrinth __P((cx_chan_t *c));
static ointhand2_t cxintr;
static int cxtinth __P((cx_chan_t *c));
#ifdef DEBUG
# define print(s) printf s
#else
# define print(s) {/*void*/}
#endif
#define TXTIMEOUT 10 /* transmit timeout in seconds */
#define DMABUFSZ (6*256) /* buffer size */
#define PPP_HEADER_LEN 4 /* size of PPP header */
/*
* Under BSDI it's possible to use general p2p protocol scheme,
* as well as our own one. Switching is done via IFF_ALTPHYS flag.
* Our ifnet pointer holds the buffer large enough to contain
* any of sppp and p2p structures.
*/
#define IFSTRUCTSZ (sizeof (struct sppp))
#define IFNETSZ (sizeof (struct ifnet))
static int cxsioctl (struct ifnet *ifp, u_long cmd, caddr_t data);
static void cxstart (struct ifnet *ifp);
static void cxwatchdog (struct ifnet *ifp);
static void cxinput (cx_chan_t *c, void *buf, unsigned len);
extern int cxrinta (cx_chan_t *c);
extern void cxtinta (cx_chan_t *c);
extern void cxmint (cx_chan_t *c);
extern timeout_t cxtimeout;
static void cxdown (cx_chan_t *c);
static void cxup (cx_chan_t *c);
cx_board_t cxboard [NCX]; /* adapter state structures */
cx_chan_t *cxchan [NCX*NCHAN]; /* unit to channel struct pointer */
extern struct cdevsw cx_cdevsw;
static unsigned short irq_valid_values [] = { 3, 5, 7, 10, 11, 12, 15, 0 };
static unsigned short drq_valid_values [] = { 5, 6, 7, 0 };
static unsigned short port_valid_values [] = {
0x240, 0x260, 0x280, 0x300, 0x320, 0x380, 0x3a0, 0,
};
/*
* Check that the value is contained in the list of correct values.
*/
static int valid (unsigned short value, unsigned short *list)
{
while (*list)
if (value == *list++)
return (1);
return (0);
}
/*
* Print the mbuf chain, for debug purposes only.
*/
static void printmbuf (struct mbuf *m)
{
printf ("mbuf:");
for (; m; m=m->m_next) {
if (m->m_flags & M_PKTHDR)
printf (" HDR %d:", m->m_pkthdr.len);
if (m->m_flags & M_EXT)
printf (" EXT:");
printf (" %d", m->m_len);
}
printf ("\n");
}
/*
* Make an mbuf from data.
*/
static struct mbuf *makembuf (void *buf, unsigned len)
{
struct mbuf *m, *o, *p;
MGETHDR (m, M_DONTWAIT, MT_DATA);
if (! m)
return (0);
if (len >= MINCLSIZE)
MCLGET (m, M_DONTWAIT);
m->m_pkthdr.len = len;
m->m_len = 0;
p = m;
while (len) {
unsigned n = M_TRAILINGSPACE (p);
if (n > len)
n = len;
if (! n) {
/* Allocate new mbuf. */
o = p;
MGET (p, M_DONTWAIT, MT_DATA);
if (! p) {
m_freem (m);
return (0);
}
if (len >= MINCLSIZE)
MCLGET (p, M_DONTWAIT);
p->m_len = 0;
o->m_next = p;
n = M_TRAILINGSPACE (p);
if (n > len)
n = len;
}
bcopy (buf, mtod (p, caddr_t) + p->m_len, n);
p->m_len += n;
buf = (char *)buf + n;
len -= n;
}
return (m);
}
/*
* Test the presence of the adapter on the given i/o port.
*/
static int
cxprobe (struct isa_device *id)
{
int unit = id->id_unit;
int iobase = id->id_iobase;
int irq = id->id_irq;
int drq = id->id_drq;
int irqnum;
irqnum = ffs (irq) - 1;
print (("cx%d: probe iobase=0x%x irq=%d drq=%d\n",
unit, iobase, irqnum, drq));
if (! valid (irqnum, irq_valid_values)) {
printf ("cx%d: Incorrect IRQ: %d\n", unit, irqnum);
return (0);
}
if (! valid (iobase, port_valid_values)) {
printf ("cx%d: Incorrect port address: 0x%x\n", unit, iobase);
return (0);
}
if (! valid (drq, drq_valid_values)) {
printf ("cx%d: Incorrect DMA channel: %d\n", unit, drq);
return (0);
}
if (! cx_probe_board (iobase))
return (0);
return (1);
}
/*
* The adapter is present, initialize the driver structures.
*/
static int
cxattach (struct isa_device *id)
{
int unit = id->id_unit;
int iobase = id->id_iobase;
int irq = id->id_irq;
int drq = id->id_drq;
cx_board_t *b = cxboard + unit;
int i;
struct sppp *sp;
id->id_ointr = cxintr;
/* Initialize the board structure. */
cx_init (b, unit, iobase, ffs(irq)-1, drq);
for (i=0; i<NCHAN; ++i) {
cx_chan_t *c = b->chan + i;
int u = b->num*NCHAN + i;
cxchan[u] = c;
if (c->type == T_NONE)
continue;
/* Allocate the buffer memory. */
c->arbuf = malloc (DMABUFSZ, M_DEVBUF, M_NOWAIT);
c->brbuf = malloc (DMABUFSZ, M_DEVBUF, M_NOWAIT);
c->atbuf = malloc (DMABUFSZ, M_DEVBUF, M_NOWAIT);
c->btbuf = malloc (DMABUFSZ, M_DEVBUF, M_NOWAIT);
/* All buffers should be located in lower 16M of memory! */
if (!c->arbuf || !c->brbuf || !c->atbuf || !c->btbuf) {
printf ("cx%d.%d: No memory for channel buffers\n",
c->board->num, c->num);
c->type = T_NONE;
}
switch (c->type) {
case T_SYNC_RS232:
case T_SYNC_V35:
case T_SYNC_RS449:
case T_UNIV_RS232:
case T_UNIV_RS449:
case T_UNIV_V35:
c->ifp = malloc (IFSTRUCTSZ, M_DEVBUF, M_NOWAIT);
if (! c->ifp) {
printf ("cx%d.%d: No memory for ifnet buffer\n",
c->board->num, c->num);
c->type = T_NONE;
continue;
}
bzero (c->ifp, IFSTRUCTSZ);
c->master = c->ifp;
c->ifp->if_softc = c;
c->ifp->if_unit = u;
c->ifp->if_name = "cx";
c->ifp->if_mtu = PP_MTU;
c->ifp->if_flags = IFF_POINTOPOINT | IFF_MULTICAST;
c->ifp->if_ioctl = cxsioctl;
c->ifp->if_start = (start_func_t) cxstart;
c->ifp->if_watchdog = (watchdog_func_t) cxwatchdog;
/* Init routine is never called by upper level? */
sppp_attach (c->ifp);
if_attach (c->ifp);
sp = (struct sppp*) c->ifp;
/* If BPF is in the kernel, call the attach for it. */
bpfattach (c->ifp, DLT_PPP, PPP_HEADER_LEN);
}
}
/* Reset the adapter. */
cx_setup_board (b);
/* Activate the timeout routine. */
if (unit == 0)
timeout (cxtimeout, 0, hz*5);
printf ("cx%d: <Cronyx-%s>\n", unit, b->name);
make_dev(&cx_cdevsw, unit, UID_ROOT, GID_WHEEL, 0600, "cx%d", unit);
return (1);
}
struct isa_driver cxdriver = {
INTR_TYPE_NET,
cxprobe,
cxattach,
"cx"
};
COMPAT_ISA_DRIVER(cx, cxdriver);
/*
* Process an ioctl request.
*/
static int
cxsioctl (struct ifnet *ifp, u_long cmd, caddr_t data)
{
cx_chan_t *q, *c = ifp->if_softc;
int error, s, was_up, should_be_up;
/*
* No socket ioctls while the channel is in async mode.
*/
if (c->type==T_NONE || c->mode==M_ASYNC)
return (EINVAL);
/*
* Socket ioctls on slave subchannels are not allowed.
*/
if (c->master != c->ifp)
return (EBUSY);
was_up = (ifp->if_flags & IFF_RUNNING) != 0;
error = sppp_ioctl (ifp, cmd, data);
if (error)
return (error);
print (("cxioctl (%d.%d, ", c->board->num, c->num));
switch (cmd) {
default:
print (("0x%x)\n", cmd));
return (0);
case SIOCADDMULTI:
print (("SIOCADDMULTI)\n"));
return (0);
case SIOCDELMULTI:
print (("SIOCDELMULTI)\n"));
return (0);
case SIOCSIFFLAGS:
print (("SIOCSIFFLAGS)\n"));
break;
case SIOCSIFADDR:
print (("SIOCSIFADDR)\n"));
break;
}
/* We get here only in case of SIFFLAGS or SIFADDR. */
s = splimp ();
should_be_up = (ifp->if_flags & IFF_RUNNING) != 0;
if (!was_up && should_be_up) {
/* Interface goes up -- start it. */
cxup (c);
/* Start all slave subchannels. */
for (q=c->slaveq; q; q=q->slaveq)
cxup (q);
cxstart (c->ifp);
} else if (was_up && !should_be_up) {
/* Interface is going down -- stop it. */
cxdown (c);
/* Stop all slave subchannels. */
for (q=c->slaveq; q; q=q->slaveq)
cxdown (q);
/* Flush the interface output queue */
if (! c->sopt.ext)
sppp_flush (c->ifp);
}
splx (s);
return (0);
}
/*
* Stop the interface. Called on splimp().
*/
static void
cxdown (cx_chan_t *c)
{
unsigned short port = c->chip->port;
print (("cx%d.%d: cxdown\n", c->board->num, c->num));
/* The interface is down, stop it */
c->ifp->if_flags &= ~IFF_OACTIVE;
/* Reset the channel (for sync modes only) */
outb (CAR(port), c->num & 3);
outb (STCR(port), STC_ABORTTX | STC_SNDSPC);
cx_setup_chan (c);
}
/*
* Start the interface. Called on splimp().
*/
static void
cxup (cx_chan_t *c)
{
unsigned short port = c->chip->port;
/* The interface is up, start it */
print (("cx%d.%d: cxup\n", c->board->num, c->num));
/* Initialize channel, enable receiver and transmitter */
cx_cmd (port, CCR_INITCH | CCR_ENRX | CCR_ENTX);
/* Repeat the command, to avoid the rev.H bug */
cx_cmd (port, CCR_INITCH | CCR_ENRX | CCR_ENTX);
/* Start receiver */
outw (ARBCNT(port), DMABUFSZ);
outb (ARBSTS(port), BSTS_OWN24);
outw (BRBCNT(port), DMABUFSZ);
outb (BRBSTS(port), BSTS_OWN24);
/* Raise DTR and RTS */
cx_chan_dtr (c, 1);
cx_chan_rts (c, 1);
/* Enable interrupts */
outb (IER(port), IER_RXD | IER_TXD);
}
/*
* Fill transmitter buffer with data.
*/
static void
cxput (cx_chan_t *c, char b)
{
struct mbuf *m;
unsigned char *buf;
unsigned short port = c->chip->port, len, cnt_port, sts_port;
/* Choose the buffer. */
if (b == 'A') {
buf = c->atbuf;
cnt_port = ATBCNT(port);
sts_port = ATBSTS(port);
} else {
buf = c->btbuf;
cnt_port = BTBCNT(port);
sts_port = BTBSTS(port);
}
/* Is it busy? */
if (inb (sts_port) & BSTS_OWN24) {
if (c->ifp->if_flags & IFF_DEBUG)
print (("cx%d.%d: tbuf %c already busy, bsts=%b\n",
c->board->num, c->num, b,
inb (sts_port), BSTS_BITS));
goto ret;
}
/* Get the packet to send. */
m = sppp_dequeue (c->master);
if (! m)
return;
len = m->m_pkthdr.len;
/* Count the transmitted bytes to the subchannel, not the master. */
c->master->if_obytes -= len + 3;
c->ifp->if_obytes += len + 3;
c->stat->obytes += len + 3;
if (len >= DMABUFSZ) {
printf ("cx%d.%d: too long packet: %d bytes: ",
c->board->num, c->num, len);
printmbuf (m);
m_freem (m);
return;
}
m_copydata (m, 0, len, buf);
if (c->ifp->if_bpf)
bpf_mtap (c->ifp, m);
m_freem (m);
/* Start transmitter. */
outw (cnt_port, len);
outb (sts_port, BSTS_EOFR | BSTS_INTR | BSTS_OWN24);
if (c->ifp->if_flags & IFF_DEBUG)
print (("cx%d.%d: enqueue %d bytes to %c\n",
c->board->num, c->num, len, buf==c->atbuf ? 'A' : 'B'));
ret:
c->ifp->if_flags |= IFF_OACTIVE;
}
/*
* Start output on the (slave) interface. Get another datagram to send
* off of the interface queue, and copy it to the interface
* before starting the output.
*/
static void
cxsend (cx_chan_t *c)
{
unsigned short port = c->chip->port;
if (c->ifp->if_flags & IFF_DEBUG)
print (("cx%d.%d: cxsend\n", c->board->num, c->num));
/* No output if the interface is down. */
if (! (c->ifp->if_flags & IFF_RUNNING))
return;
/* Set the current channel number. */
outb (CAR(port), c->num & 3);
/* Determine the buffer order. */
if (inb (DMABSTS(port)) & DMABSTS_NTBUF) {
cxput (c, 'B');
cxput (c, 'A');
} else {
cxput (c, 'A');
cxput (c, 'B');
}
/* Set up transmit timeout. */
if (c->master->if_flags & IFF_OACTIVE)
c->master->if_timer = TXTIMEOUT;
/*
* Enable TXMPTY interrupt,
* to catch the case when the second buffer is empty.
*/
if ((inb (ATBSTS(port)) & BSTS_OWN24) &&
(inb (BTBSTS(port)) & BSTS_OWN24)) {
outb (IER(port), IER_RXD | IER_TXD | IER_TXMPTY);
} else
outb (IER(port), IER_RXD | IER_TXD);
}
/*
* Start output on the (master) interface and all slave interfaces.
* Always called on splimp().
*/
static void
cxstart (struct ifnet *ifp)
{
cx_chan_t *q, *c = ifp->if_softc;
if (c->ifp->if_flags & IFF_DEBUG)
print (("cx%d.%d: cxstart\n", c->board->num, c->num));
/* Start the master subchannel. */
cxsend (c);
/* Start all slave subchannels. */
if (c->slaveq && ! sppp_isempty (c->master))
for (q=c->slaveq; q; q=q->slaveq)
if ((q->ifp->if_flags & IFF_RUNNING) &&
! (q->ifp->if_flags & IFF_OACTIVE))
cxsend (q);
}
/*
* Handle transmit timeouts.
* Recover after lost transmit interrupts.
* Always called on splimp().
*/
static void
cxwatchdog (struct ifnet *ifp)
{
cx_chan_t *q, *c = ifp->if_softc;
if (! (ifp->if_flags & IFF_RUNNING))
return;
if (ifp->if_flags & IFF_DEBUG)
printf ("cx%d.%d: device timeout\n", c->board->num, c->num);
cxdown (c);
for (q=c->slaveq; q; q=q->slaveq)
cxdown (q);
cxup (c);
for (q=c->slaveq; q; q=q->slaveq)
cxup (q);
cxstart (ifp);
}
/*
* Handle receive interrupts, including receive errors and
* receive timeout interrupt.
*/
static void
cxrinth (cx_chan_t *c)
{
unsigned short port = c->chip->port;
unsigned short len, risr = inw (RISR(port));
/* Receive errors. */
if (risr & (RIS_BUSERR | RIS_OVERRUN | RISH_CRCERR | RISH_RXABORT)) {
if (c->ifp->if_flags & IFF_DEBUG)
printf ("cx%d.%d: receive error, risr=%b\n",
c->board->num, c->num, risr, RISH_BITS);
++c->ifp->if_ierrors;
++c->stat->ierrs;
if (risr & RIS_OVERRUN)
++c->ifp->if_collisions;
} else if (risr & RIS_EOBUF) {
if (c->ifp->if_flags & IFF_DEBUG)
print (("cx%d.%d: hdlc receive interrupt, risr=%b, arbsts=%b, brbsts=%b\n",
c->board->num, c->num, risr, RISH_BITS,
inb (ARBSTS(port)), BSTS_BITS,
inb (BRBSTS(port)), BSTS_BITS));
++c->stat->ipkts;
/* Handle received data. */
len = (risr & RIS_BB) ? inw(BRBCNT(port)) : inw(ARBCNT(port));
c->stat->ibytes += len;
if (len > DMABUFSZ) {
/* Fatal error: actual DMA transfer size
* exceeds our buffer size. It could be caused
* by incorrectly programmed DMA register or
* hardware fault. Possibly, should panic here. */
printf ("cx%d.%d: panic! DMA buffer overflow: %d bytes\n",
c->board->num, c->num, len);
++c->ifp->if_ierrors;
} else if (! (risr & RIS_EOFR)) {
/* The received frame does not fit in the DMA buffer.
* It could be caused by serial lie noise,
* or if the peer has too big MTU. */
if (c->ifp->if_flags & IFF_DEBUG)
printf ("cx%d.%d: received frame length exceeds MTU, risr=%b\n",
c->board->num, c->num, risr, RISH_BITS);
++c->ifp->if_ierrors;
} else {
/* Valid frame received. */
if (c->ifp->if_flags & IFF_DEBUG)
print (("cx%d.%d: hdlc received %d bytes\n",
c->board->num, c->num, len));
cxinput (c, (risr & RIS_BB) ? c->brbuf : c->arbuf, len);
++c->ifp->if_ipackets;
}
} else if (c->ifp->if_flags & IFF_DEBUG) {
print (("cx%d.%d: unknown hdlc receive interrupt, risr=%b\n",
c->board->num, c->num, risr, RISH_BITS));
++c->stat->ierrs;
}
/* Restart receiver. */
if (! (inb (ARBSTS(port)) & BSTS_OWN24)) {
outw (ARBCNT(port), DMABUFSZ);
outb (ARBSTS(port), BSTS_OWN24);
}
if (! (inb (BRBSTS(port)) & BSTS_OWN24)) {
outw (BRBCNT(port), DMABUFSZ);
outb (BRBSTS(port), BSTS_OWN24);
}
}
/*
* Handle transmit interrupt.
*/
static int
cxtinth (cx_chan_t *c)
{
unsigned short port = c->chip->port;
unsigned char tisr = inb (TISR(port));
unsigned char teoir = 0;
c->ifp->if_flags &= ~IFF_OACTIVE;
if (c->ifp == c->master)
c->ifp->if_timer = 0;
if (tisr & (TIS_BUSERR | TIS_UNDERRUN)) {
/* if (c->ifp->if_flags & IFF_DEBUG) */
print (("cx%d.%d: transmit error, tisr=%b, atbsts=%b, btbsts=%b\n",
c->board->num, c->num, tisr, TIS_BITS,
inb (ATBSTS(port)), BSTS_BITS,
inb (BTBSTS(port)), BSTS_BITS));
++c->ifp->if_oerrors;
++c->stat->oerrs;
/* Terminate the failed buffer. */
/* teoir = TEOI_TERMBUFF; */
} else if (c->ifp->if_flags & IFF_DEBUG)
print (("cx%d.%d: hdlc transmit interrupt, tisr=%b, atbsts=%b, btbsts=%b\n",
c->board->num, c->num, tisr, TIS_BITS,
inb (ATBSTS(port)), BSTS_BITS,
inb (BTBSTS(port)), BSTS_BITS));
if (tisr & TIS_EOFR) {
++c->ifp->if_opackets;
++c->stat->opkts;
}
/* Start output on the (sub-) channel. */
cxsend (c);
return (teoir);
}
static void
cxintr (int bnum)
{
cx_board_t *b = cxboard + bnum;
while (! (inw (BSR(b->port)) & BSR_NOINTR)) {
/* Acknowledge the interrupt to enter the interrupt context. */
/* Read the local interrupt vector register. */
unsigned char livr = inb (IACK(b->port, BRD_INTR_LEVEL));
cx_chan_t *c = b->chan + (livr>>2 & 0xf);
unsigned short port = c->chip->port;
unsigned short eoiport = REOIR(port);
unsigned char eoi = 0;
if (c->type == T_NONE) {
printf ("cx%d.%d: unexpected interrupt, livr=0x%x\n",
c->board->num, c->num, livr);
continue; /* incorrect channel number? */
}
/* print (("cx%d.%d: interrupt, livr=0x%x\n",
c->board->num, c->num, livr)); */
/* Clear RTS to stop receiver data flow while we are busy
* processing the interrupt, thus avoiding underruns. */
if (! c->sopt.norts) {
outb (MSVR_RTS(port), 0);
c->rts = 0;
}
switch (livr & 3) {
case LIV_EXCEP: /* receive exception */
case LIV_RXDATA: /* receive interrupt */
++c->stat->rintr;
switch (c->mode) {
case M_ASYNC: eoi = cxrinta (c); break;
case M_HDLC: cxrinth (c); break;
default:; /* No bisync and X.21 yet */
}
break;
case LIV_TXDATA: /* transmit interrupt */
++c->stat->tintr;
eoiport = TEOIR(port);
switch (c->mode) {
case M_ASYNC: cxtinta (c); break;
case M_HDLC: eoi = cxtinth (c); break;
default:; /* No bisync and X.21 yet */
}
break;
case LIV_MODEM: /* modem/timer interrupt */
++c->stat->mintr;
eoiport = MEOIR(port);
cxmint (c);
break;
}
/* Raise RTS for this channel if and only if
* both receive buffers are empty. */
if (! c->sopt.norts && (inb (CSR(port)) & CSRA_RXEN) &&
(inb (ARBSTS(port)) & BSTS_OWN24) &&
(inb (BRBSTS(port)) & BSTS_OWN24)) {
outb (MSVR_RTS(port), MSV_RTS);
c->rts = 1;
}
/* Exit from interrupt context. */
outb (eoiport, eoi);
/* Master channel - start output on all idle subchannels. */
if (c->master == c->ifp && c->slaveq &&
(livr & 3) == LIV_TXDATA && c->mode == M_HDLC &&
! sppp_isempty (c->ifp)) {
cx_chan_t *q;
for (q=c->slaveq; q; q=q->slaveq)
if ((q->ifp->if_flags & IFF_RUNNING) &&
! (q->ifp->if_flags & IFF_OACTIVE))
cxsend (q);
}
}
}
/*
* Process the received packet.
*/
static void
cxinput (cx_chan_t *c, void *buf, unsigned len)
{
/* Make an mbuf. */
struct mbuf *m = makembuf (buf, len);
if (! m) {
if (c->ifp->if_flags & IFF_DEBUG)
printf ("cx%d.%d: no memory for packet\n",
c->board->num, c->num);
++c->ifp->if_iqdrops;
return;
}
m->m_pkthdr.rcvif = c->master;
#ifdef DEBUG
if (c->ifp->if_flags & IFF_DEBUG)
printmbuf (m);
#endif
/*
* Check if there's a BPF listener on this interface.
* If so, hand off the raw packet to bpf.
*/
if (c->ifp->if_bpf)
bpf_tap (c->ifp, buf, len);
/* Count the received bytes to the subchannel, not the master. */
c->master->if_ibytes -= len + 3;
c->ifp->if_ibytes += len + 3;
sppp_input (c->master, m);
}
void cxswitch (cx_chan_t *c, cx_soft_opt_t new)
{
new.ext = 0;
if (! new.ext) {
struct sppp *sp = (struct sppp*) c->ifp;
#if 0 /* Doesn't work this way any more 990402 /phk */
if (new.cisco)
sp->pp_flags |= PP_CISCO;
else
sp->pp_flags &= ~PP_CISCO;
#endif
if (new.keepalive)
sp->pp_flags |= PP_KEEPALIVE;
else
sp->pp_flags &= ~PP_KEEPALIVE;
}
c->sopt = new;
}