mirror of
https://git.FreeBSD.org/src.git
synced 2024-12-21 11:13:30 +00:00
127 lines
4.7 KiB
HTML
127 lines
4.7 KiB
HTML
<HTML><HEAD><TITLE>
|
|
Spectracom 8170 and Netclock/2 WWVB Receivers
|
|
</TITLE></HEAD><BODY><H3>
|
|
Spectracom 8170 and Netclock/2 WWVB Receivers
|
|
</H3><HR>
|
|
|
|
<H4>Synopsis</H4>
|
|
|
|
Address: 127.127.4.<I>u</I>
|
|
<BR>Reference ID: <TT>WWVB</TT>
|
|
<BR>Driver ID: <TT>WWVB_SPEC</TT>
|
|
<BR>Serial Port: <TT>/dev/wwvb<I>u</I></TT>; 9600 baud, 8-bits, no
|
|
parity
|
|
<BR>Features: <TT>tty_clk</TT>
|
|
|
|
<H4>Description</H4>
|
|
|
|
This driver supports all known Spectracom radio and satellite clocks,
|
|
including the Model 8170 and Netclock/2 WWVB Synchronized Clocks and the
|
|
Netclock/GPS GPS Master Clock. The claimed accuracy of the WWVB clocks
|
|
is 100 usec relative to the broadcast signal. These clocks have proven a
|
|
reliable source of time, except in some parts of the country with high
|
|
levels of conducted RF interference. WIth the GPS clock the claimed
|
|
accuracy is 130 ns. However, in most cases the actual accuracy is
|
|
limited by the precision of the timecode and the latencies of the serial
|
|
interface and operating system.
|
|
|
|
<P>The DIPswitches on these clocks should be set to 24-hour display,
|
|
AUTO DST off, data format 0 or 2 (see below) and baud rate 9600. If this
|
|
clock is used as the source for the IRIG Audio Decoder
|
|
(<tt>refclock_irig.c</tt> in this distribution), set the DIPswitches for
|
|
AM IRIG output and IRIG format 1 (IRIG B with signature control).
|
|
|
|
<P>There are two timecode formats used by these clocks. Format 0, which
|
|
is available with all clocks, and format 2, which is available with all
|
|
clocks except the original (unmodified) Model 8170.
|
|
|
|
<P>Format 0 (22 ASCII printing characters):
|
|
<br><cr><lf>i ddd hh:mm:ss TZ=zz<cr><lf>
|
|
|
|
<p>on-time = first <cr>
|
|
<br>i = synchronization flag (' ' = in synch, '?' = out synch)
|
|
<br>hh:mm:ss = hours, minutes, seconds</PRE>
|
|
|
|
<p>The alarm condition is indicated by other than ' ' at <TT>i</TT>,
|
|
which occurs during initial synchronization and when received signal is
|
|
lost for about ten hours.
|
|
|
|
<P>Format 2 (24 ASCII printing characters):
|
|
<br>lt;cr>lf>iqyy ddd hh:mm:ss.fff ld
|
|
|
|
<p>on-time = <cr>
|
|
<br>i = synchronization flag (' ' = in synch, '?' = out synch)
|
|
<br>q = quality indicator (' ' = locked, 'A'...'D' = unlocked)
|
|
<br>yy = year (as broadcast)
|
|
<br>ddd = day of year
|
|
<br>hh:mm:ss.fff = hours, minutes, seconds, milliseconds</PRE>
|
|
|
|
<p>The alarm condition is indicated by other than ' ' at <TT>i</TT>,
|
|
which occurs during initial synchronization and when received signal is
|
|
lost for about ten hours. The unlock condition is indicated by other
|
|
than ' ' at <TT>q</TT>.
|
|
|
|
<P>The <TT>q</TT> is normally ' ' when the time error is less than 1 ms
|
|
and a character in the set <TT>A...D</TT> when the time error is less
|
|
than 10, 100, 500 and greater than 500 ms respectively. The <TT>l</TT>
|
|
is normally ' ', but is set to <TT>L</TT> early in the month of an
|
|
upcoming UTC leap second and reset to ' ' on the first day of the
|
|
following month. The <TT>d</TT> is set to <TT>S</TT> for standard time
|
|
<TT>S</TT>, <TT>I</TT> on the day preceding a switch to daylight time,
|
|
<TT>D</TT> for daylight time and <TT>O</TT> on the day preceding a
|
|
switch to standard time. The start bit of the first
|
|
<cr> is synchronized to the indicated time as returned.
|
|
|
|
<P>This driver does not need to be told which format is in use - it
|
|
figures out which one from the length of the message. A three-stage
|
|
median filter is used to reduce jitter and provide a dispersion measure.
|
|
The driver makes no attempt to correct for the intrinsic jitter of the
|
|
radio itself, which is a known problem with the older radios.
|
|
|
|
<H4>Monitor Data</H4>
|
|
|
|
The driver writes each timecode as received to the <TT>clockstats</TT>
|
|
file. When enabled by the <TT>flag4</TT> fudge flag, a table of quality
|
|
data maintained internally by the Netclock/2 is retrieved and written to
|
|
the <TT>clockstats</TT> file when the first timecode message of a new
|
|
dayis received.
|
|
|
|
<H4>Fudge Factors</H4>
|
|
|
|
<DL>
|
|
|
|
<DT><TT>time1 <I>time</I></TT></DT>
|
|
<DD>Specifies the time offset calibration factor, in seconds and
|
|
fraction,
|
|
with default 0.0.</DD>
|
|
|
|
<DT><TT>time2 <I>time</I></TT></DT>
|
|
<DD>Not used by this driver.</DD>
|
|
|
|
<DT><TT>stratum <I>number</I></TT></DT>
|
|
<DD>Specifies the driver stratum, in decimal from 0 to 15, with default
|
|
0.</DD>
|
|
|
|
<DT><TT>refid <I>string</I></TT></DT>
|
|
<DD>Specifies the driver reference identifier, an ASCII string from one
|
|
to four characters, with default <TT>WWVB</TT>.</DD>
|
|
|
|
<DT><TT>flag1 0 | 1</TT></DT>
|
|
<DD>Not used by this driver.</DD>
|
|
|
|
<DT><TT>flag2 0 | 1</TT></DT>
|
|
<DD>Not used by this driver.</DD>
|
|
|
|
<DT><TT>flag3 0 | 1</TT></DT>
|
|
<DD>Not used by this driver.</DD>
|
|
|
|
<DT><TT>flag4 0 | 1</TT></DT>
|
|
<DD>Enable verbose <TT>clockstats</TT> recording if set.</DD>
|
|
|
|
</DL>
|
|
|
|
Additional Information
|
|
|
|
<P><A HREF="refclock.htm">Reference Clock Drivers</A>
|
|
<HR><ADDRESS>David L. Mills (mills@udel.edu)</ADDRESS></BODY></HTML>
|