mirror/freebsd
1
0
Fork 0
mirror of https://git.FreeBSD.org/src.git synced 2024-12-25 11:37:56 +00:00
Code Issues Releases Activity
3d3169c858
freebsd/sys/dev/ep/if_epreg.h
Rebecca Cran 6bccea7c2b Fix typos - remove duplicate "the". 
PR:	bin/154928
Submitted by:	Eitan Adler <lists at eitanadler.com>
MFC after: 	3 days
2011-02-21 09:01:34 +00:00

435 lines
14 KiB
C
Raw Blame History

/*-
* Copyright (c) 1993 Herb Peyerl (hpeyerl@novatel.ca) All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions are
* met: 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer. 2. The name
* of the author may not be used to endorse or promote products derived from
* this software without specific prior written permission
*
* THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR IMPLIED
* WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
* MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO
* EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
* SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED
* TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
* PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
* LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
* NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
* SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*
* $FreeBSD$
*/
/*
* DELAY_MULTIPLE: How much to boost "base" delays, except
* for the inter-bit delays in get_eeprom_data. A cyrix Media GX needed this.
*/
#define DELAY_MULTIPLE 10
#define BIT_DELAY_MULTIPLE 10
/*
* Some global constants
*/
#define TX_INIT_RATE 16
#define TX_INIT_MAX_RATE 64
#define RX_INIT_LATENCY 64
#define RX_INIT_EARLY_THRESH 208/* not less than MINCLSIZE */
#define RX_NEXT_EARLY_THRESH 500
#define EEPROMSIZE 0x40
#define MAX_EEPROMBUSY 1000
#define EP_LAST_TAG 0xd7
#define EP_MAX_BOARDS 16
#define EP_IOSIZE 16 /* 16 bytes of I/O space used. */
/*
* Commands to read/write EEPROM trough EEPROM command register (Window 0,
* Offset 0xa)
*/
#define EEPROM_CMD_RD 0x0080 /* Read: Address required (5 bits) */
#define EEPROM_CMD_WR 0x0040 /* Write: Address required (5 bits) */
#define EEPROM_CMD_ERASE 0x00c0 /* Erase: Address required (5 bits) */
#define EEPROM_CMD_EWEN 0x0030 /* Erase/Write Enable: No data required */
#define EEPROM_BUSY (1<<15)
#define EEPROM_TST_MODE (1<<14)
/*
* Some short functions, worth to let them be a macro
*/
#define is_eeprom_busy(sc) (CSR_READ_2(sc, EP_W0_EEPROM_COMMAND)&EEPROM_BUSY)
#define GO_WINDOW(sc, x) CSR_WRITE_2(sc, EP_COMMAND, WINDOW_SELECT|(x))
/**************************************************************************
* *
* These define the EEPROM data structure. They are used in the probe
* function to verify the existence of the adapter after having sent
* the ID_Sequence.
*
**************************************************************************/
#define EEPROM_NODE_ADDR_0 0x0 /* Word */
#define EEPROM_NODE_ADDR_1 0x1 /* Word */
#define EEPROM_NODE_ADDR_2 0x2 /* Word */
#define EEPROM_PROD_ID 0x3 /* 0x9[0-f]50 */
#define EEPROM_MFG_DATE 0x4 /* Manufacturing date */
#define EEPROM_MFG_DIVSION 0x5 /* Manufacturing division */
#define EEPROM_MFG_PRODUCT 0x6 /* Product code */
#define EEPROM_MFG_ID 0x7 /* 0x6d50 */
#define EEPROM_ADDR_CFG 0x8 /* Base addr */
#define ADDR_CFG_EISA 0x1f
#define ADDR_CFG_MASK 0x1f
#define EEPROM_RESOURCE_CFG 0x9 /* IRQ. Bits 12-15 */
#define EEPROM_OEM_ADDR0 0xa
#define EEPROM_OEM_ADDR1 0xb
#define EEPROM_OEM_ADDR2 0xc
#define EEPROM_SOFTINFO 0xd
#define EEPROM_COMPAT 0xe
#define EEPROM_SOFTINFO2 0xf
#define EEPROM_CAP 0x10
#define CAP_ISA 0x2083
#define CAP_PCMCIA 0x2082
#define EEPROM_INT_CONFIG_0 0x12
#define EEPROM_INT_CONFIG_1 0x13
/* RAM Partition TX FIFO/RX FIFO */
#define ICW1_RAM_PART_MASK 0x03
#define ICW1_RAM_PART_35 0x00 /* 2:5 (only legal if RAM size == 000b
* default power-up/reset */
#define ICW1_RAM_PART_13 0x01 /* 1:3 (only legal if RAM size ==
* 000b) */
#define ICW1_RAM_PART_11 0x10 /* 1:1 */
#define ICW1_RAM_PART_RESV 0x11 /* Reserved */
/* ISA Adapter Selection */
#define ICW1_IAS_MASK 0x0c
#define ICW1_IAS_DIS 0x00 /* Both mechanisms disabled (default) */
#define ICW1_IAS_ISA 0x04 /* ISA contention only */
#define ICW1_IAS_PNP 0x08 /* ISA Plug and Play only */
#define ICW1_IAS_BOTH 0x0c /* Both mechanisms enabled */
#define EEPROM_CHECKSUM_EL3 0x17
/**************************************************************************
* *
* These are the registers for the 3Com 3c509 and their bit patterns when *
* applicable. They have been taken out the "EtherLink III Parallel *
* Tasking EISA and ISA Technical Reference" "Beta Draft 10/30/92" manual *
* from 3com. *
* *
**************************************************************************/
#define EP_COMMAND 0x0e /* Write. BASE+0x0e is always a
* command reg. */
#define EP_STATUS 0x0e /* Read. BASE+0x0e is always status
* reg. */
#define EP_WINDOW 0x0f /* Read. BASE+0x0f is always window
* reg. */
/*
* Window 0 registers. Setup.
*/
/* Write */
#define EP_W0_EEPROM_DATA 0x0c
#define EP_W0_EEPROM_COMMAND 0x0a
#define EP_W0_RESOURCE_CFG 0x08
#define EP_W0_ADDRESS_CFG 0x06
#define EP_W0_CONFIG_CTRL 0x04
/* Read */
#define EP_W0_PRODUCT_ID 0x02
#define EP_W0_MFG_ID 0x00
/*
* Window 1 registers. Operating Set.
*/
/* Write */
#define EP_W1_TX_PIO_WR_2 0x02
#define EP_W1_TX_PIO_WR_1 0x00
/* Read */
#define EP_W1_FREE_TX 0x0c
#define EP_W1_TX_STATUS 0x0b /* byte */
#define EP_W1_TIMER 0x0a /* byte */
#define EP_W1_RX_STATUS 0x08
#define EP_W1_RX_PIO_RD_2 0x02
#define EP_W1_RX_PIO_RD_1 0x00
/*
* Window 2 registers. Station Address Setup/Read
*/
/* Read/Write */
#define EP_W2_PHY_MGMT 0x0c
#define EP_W2_ALT_EEPROM 0x0a
#define EP_W2_ADDR_5 0x05
#define EP_W2_ADDR_4 0x04
#define EP_W2_ADDR_3 0x03
#define EP_W2_ADDR_2 0x02
#define EP_W2_ADDR_1 0x01
#define EP_W2_ADDR_0 0x00
/*
* Window 3 registers. FIFO Management.
*/
/* Read */
#define EP_W3_FREE_TX 0x0c
#define EP_W3_FREE_RX 0x0a
#define EP_W3_OPTIONS 0x08
/*
* Window 4 registers. Diagnostics.
*/
/* Read/Write */
#define EP_W4_MEDIA_TYPE 0x0a
#define EP_W4_CTRLR_STATUS 0x08
#define EP_W4_NET_DIAG 0x06
#define EP_W4_FIFO_DIAG 0x04
#define EP_W4_HOST_DIAG 0x02
#define EP_W4_TX_DIAG 0x00
/*
* Window 5 Registers. Results and Internal status.
*/
/* Read */
#define EP_W5_READ_0_MASK 0x0c
#define EP_W5_INTR_MASK 0x0a
#define EP_W5_RX_FILTER 0x08
#define EP_W5_RX_EARLY_THRESH 0x06
#define EP_W5_TX_AVAIL_THRESH 0x02
#define EP_W5_TX_START_THRESH 0x00
/*
* Window 6 registers. Statistics.
*/
/* Read/Write */
#define TX_TOTAL_OK 0x0c
#define RX_TOTAL_OK 0x0a
#define TX_DEFERRALS 0x08
#define RX_FRAMES_OK 0x07
#define TX_FRAMES_OK 0x06
#define RX_OVERRUNS 0x05
#define TX_COLLISIONS 0x04
#define TX_AFTER_1_COLLISION 0x03
#define TX_AFTER_X_COLLISIONS 0x02
#define TX_NO_SQE 0x01
#define TX_CD_LOST 0x00
/****************************************
*
* Register definitions.
*
****************************************/
/*
* Command parameter that disables threshold interrupts
* PIO (3c509) cards use 2044. The fifo word-oriented and 2044--2047 work.
* "busmastering" cards need 8188.
* The implicit two-bit upshift done by busmastering cards means
* a value of 2047 disables threshold interrupts on both.
*/
#define EP_THRESH_DISABLE 2047
/*
* Command register. All windows.
*
* 16 bit register.
* 15-11: 5-bit code for command to be executed.
* 10-0: 11-bit arg if any. For commands with no args;
* this can be set to anything.
*/
#define GLOBAL_RESET (u_short) 0x0000 /* Wait at least 1ms
* after issuing */
#define WINDOW_SELECT (u_short) (0x1<<11)
#define START_TRANSCEIVER (u_short) (0x2<<11) /* Read ADDR_CFG reg to
* determine whether
* this is needed. If
* so; wait 800 uSec
* before using trans-
* ceiver. */
#define RX_DISABLE (u_short) (0x3<<11) /* state disabled on
* power-up */
#define RX_ENABLE (u_short) (0x4<<11)
#define RX_RESET (u_short) (0x5<<11)
#define RX_DISCARD_TOP_PACK (u_short) (0x8<<11)
#define TX_ENABLE (u_short) (0x9<<11)
#define TX_DISABLE (u_short) (0xa<<11)
#define TX_RESET (u_short) (0xb<<11)
#define REQ_INTR (u_short) (0xc<<11)
/*
* The following C_* acknowledge the various interrupts. Some of them don't
* do anything. See the manual.
*/
#define ACK_INTR (u_short) (0x6800)
# define C_INTR_LATCH (u_short) (ACK_INTR|0x1)
# define C_CARD_FAILURE (u_short) (ACK_INTR|0x2)
# define C_TX_COMPLETE (u_short) (ACK_INTR|0x4)
# define C_TX_AVAIL (u_short) (ACK_INTR|0x8)
# define C_RX_COMPLETE (u_short) (ACK_INTR|0x10)
# define C_RX_EARLY (u_short) (ACK_INTR|0x20)
# define C_INT_RQD (u_short) (ACK_INTR|0x40)
# define C_UPD_STATS (u_short) (ACK_INTR|0x80)
#define SET_INTR_MASK (u_short) (0xe<<11)
#define SET_RD_0_MASK (u_short) (0xf<<11)
#define SET_RX_FILTER (u_short) (0x10<<11)
# define FIL_INDIVIDUAL (u_short) (0x1)
# define FIL_MULTICAST (u_short) (0x02)
# define FIL_BRDCST (u_short) (0x04)
# define FIL_PROMISC (u_short) (0x08)
#define SET_RX_EARLY_THRESH (u_short) (0x11<<11)
#define SET_TX_AVAIL_THRESH (u_short) (0x12<<11)
#define SET_TX_START_THRESH (u_short) (0x13<<11)
#define STATS_ENABLE (u_short) (0x15<<11)
#define STATS_DISABLE (u_short) (0x16<<11)
#define STOP_TRANSCEIVER (u_short) (0x17<<11)
#define TX_PLL_ENABLE (u_short) (0x18<<11)
#define TX_PLL_DISABLE (u_short) (0x19<<11)
#define POWER_UP (u_short) (0x1b<<11)
#define POWER_DOWN (u_short) (0x1b<<11)
#define POWER_AUTO (u_short) (0x1b<<11)
/*
* Status register. All windows.
*
* 15-13: Window number(0-7).
* 12: Command_in_progress.
* 11: reserved.
* 10: reserved.
* 9: reserved.
* 8: reserved.
* 7: Update Statistics.
* 6: Interrupt Requested.
* 5: RX Early.
* 4: RX Complete.
* 3: TX Available.
* 2: TX Complete.
* 1: Adapter Failure.
* 0: Interrupt Latch.
*/
#define S_INTR_LATCH (u_short) (0x1)
#define S_CARD_FAILURE (u_short) (0x2)
#define S_TX_COMPLETE (u_short) (0x4)
#define S_TX_AVAIL (u_short) (0x8)
#define S_RX_COMPLETE (u_short) (0x10)
#define S_RX_EARLY (u_short) (0x20)
#define S_INT_RQD (u_short) (0x40)
#define S_UPD_STATS (u_short) (0x80)
#define S_MASK (u_short) 0xFF /* mask of S_* */
#define S_5_INTS (S_CARD_FAILURE|S_TX_COMPLETE|\
S_TX_AVAIL|S_RX_COMPLETE|S_RX_EARLY)
#define S_COMMAND_IN_PROGRESS (u_short) (0x1000)
#define EP_BUSY_WAIT(sc) while (CSR_READ_2(sc, EP_STATUS) & S_COMMAND_IN_PROGRESS)
/* Address Config. Register.
* Window 0/Port 06
*/
#define ACF_CONNECTOR_BITS 14
#define ACF_CONNECTOR_UTP 0
#define ACF_CONNECTOR_AUI 1
#define ACF_CONNECTOR_BNC 3
/* Resource configuration register.
* Window 0/Port 08
*
*/
#define SET_IRQ(sc, irq) CSR_WRITE_2((sc), EP_W0_RESOURCE_CFG, \
((CSR_READ_2((sc), EP_W0_RESOURCE_CFG) & 0x0fff) | \
((u_short)(irq)<<12)) ) /* set IRQ i */
/*
* FIFO Registers.
* RX Status. Window 1/Port 08
*
* 15: Incomplete or FIFO empty.
* 14: 1: Error in RX Packet 0: Incomplete or no error.
* 13-11: Type of error.
* 1000 = Overrun.
* 1011 = Run Packet Error.
* 1100 = Alignment Error.
* 1101 = CRC Error.
* 1001 = Oversize Packet Error (>1514 bytes)
* 0010 = Dribble Bits.
* (all other error codes, no errors.)
*
* 10-0: RX Bytes (0-1514)
*/
#define ERR_RX_INCOMPLETE (u_short) (0x1<<15)
#define ERR_RX (u_short) (0x1<<14)
#define ERR_RX_OVERRUN (u_short) (0x8<<11)
#define ERR_RX_RUN_PKT (u_short) (0xb<<11)
#define ERR_RX_ALIGN (u_short) (0xc<<11)
#define ERR_RX_CRC (u_short) (0xd<<11)
#define ERR_RX_OVERSIZE (u_short) (0x9<<11)
#define ERR_RX_DRIBBLE (u_short) (0x2<<11)
/*
* FIFO Registers.
* TX Status. Window 1/Port 0B
*
* Reports the transmit status of a completed transmission. Writing this
* register pops the transmit completion stack.
*
* Window 1/Port 0x0b.
*
* 7: Complete
* 6: Interrupt on successful transmission requested.
* 5: Jabber Error (TP Only, TX Reset required. )
* 4: Underrun (TX Reset required. )
* 3: Maximum Collisions.
* 2: TX Status Overflow.
* 1-0: Undefined.
*
*/
#define TXS_COMPLETE 0x80
#define TXS_SUCCES_INTR_REQ 0x40
#define TXS_JABBER 0x20
#define TXS_UNDERRUN 0x10
#define TXS_MAX_COLLISION 0x8
#define TXS_STATUS_OVERFLOW 0x4
/*
* Configuration control register.
* Window 0/Port 04
*/
/* Read */
#define IS_AUI (1<<13)
#define IS_BNC (1<<12)
#define IS_UTP (1<<9)
/* Write */
#define ENABLE_DRQ_IRQ 0x0001
#define W0_P4_CMD_RESET_ADAPTER 0x4
#define W0_P4_CMD_ENABLE_ADAPTER 0x1
/*
* Media type and status.
* Window 4/Port 0A
*/
#define JABBER_GUARD_ENABLE 0x40
#define LINKBEAT_ENABLE 0x80
#define ENABLE_UTP (JABBER_GUARD_ENABLE | LINKBEAT_ENABLE)
#define DISABLE_UTP 0x0
#define MT_CSD 0x0004 /* CRC Strip disable */
#define MT_SQE 0x0008 /* SQE Enable */
#define MT_C0 0x0010 /* Collison */
#define MT_CS 0x0020 /* Carrier Sense */
#define MT_J 0x0200 /* Jabber detected */
#define MT_PL 0x0400 /* Plarity Inverted */
#define MT_LB 0x0800 /* Link Beat detected */
#define MT_SQ 0x1000 /* SQE Present */
#define MT_IN 0x2000 /* Reserved */
#define MT_CE 0x4000 /* Coax */
#define MT_TPE 0x8000
/*
* Misc defines for various things.
*/
#define ACTIVATE_ADAPTER_TO_CONFIG 0xff /* to the id_port */
#define MFG_ID 0x6d50 /* in EEPROM and W0
* ADDR_CONFIG */
#define PROD_ID 0x9150
#define AUI 0x1
#define BNC 0x2
#define UTP 0x4
#define RX_BYTES_MASK (u_short) (0x07ff)
Reference in New Issue View Git Blame Copy Permalink