mirror of
https://git.FreeBSD.org/src.git
synced 2024-12-19 10:53:58 +00:00
dfd325ea2c
board. This is another AR9331 board similar to the Carambola2. It has different ethernet and LED wiring though. They make a variety of boards that mostly differ on the amount of RAM/flash available. Alfa Networks graciously donated a handful of 64MB RAM/16MB flash boards so I can finish off 802.11s support for the AR93xx chips and do up a tech demonstration with it. This is enough to bring up the board. Tested: * Alfa networks UB Hornet board - 64MB ram, 16MB flash version. Thankyou to Alfa Networks for the development boards! Sponsored by: Alfa Networks (hardware only)
106 lines
2.7 KiB
Plaintext
106 lines
2.7 KiB
Plaintext
#
|
|
# This file adds to the values in AR933X_BASE.hints
|
|
#
|
|
# $FreeBSD$
|
|
|
|
# mdiobus on arge1
|
|
hint.argemdio.0.at="nexus0"
|
|
hint.argemdio.0.maddr=0x1a000000
|
|
hint.argemdio.0.msize=0x1000
|
|
hint.argemdio.0.order=0
|
|
|
|
# There's no need to set the ar933x GMAC configuration bits.
|
|
# This just creates a switch instance and correctly uses it.
|
|
|
|
# Embedded Atheros Switch
|
|
hint.arswitch.0.at="mdio0"
|
|
|
|
# XXX this should really say it's an AR933x switch, as there
|
|
# are some vlan specific differences here!
|
|
hint.arswitch.0.is_7240=1
|
|
hint.arswitch.0.numphys=4
|
|
hint.arswitch.0.phy4cpu=1 # phy 4 is a "CPU" separate PHY
|
|
hint.arswitch.0.is_rgmii=0
|
|
hint.arswitch.0.is_gmii=1 # arge1 <-> switch PHY is GMII
|
|
|
|
# arge0 - MII, autoneg, phy(4)
|
|
hint.arge.0.phymask=0x10 # PHY4
|
|
hint.arge.0.mdio=mdioproxy1 # .. off of the switch mdiobus
|
|
|
|
# arge1 - GMII, 1000/full
|
|
hint.arge.1.phymask=0x0 # No directly mapped PHYs
|
|
hint.arge.1.media=1000
|
|
hint.arge.1.fduplex=1
|
|
|
|
# Where the ART is - last 64k in the flash
|
|
# 0x9fff1000 ?
|
|
hint.ath.0.eepromaddr=0x1fff0000
|
|
hint.ath.0.eepromsize=16384
|
|
|
|
# The board 16MiB flash layout in uboot env:
|
|
#
|
|
# 256k (uboot), 64k (uboot-env), 14336k (rootfs), 1600k (kernel), 64k (NVRAM), 64k (ART)
|
|
|
|
# However, it boots from 0x9f050000, which is the front of the flsah!
|
|
# Thus the kernel/rootfs are switched around.
|
|
|
|
# 256KB
|
|
hint.map.0.at="flash/spi0"
|
|
hint.map.0.start=0x00000000
|
|
hint.map.0.end=0x000040000
|
|
hint.map.0.name="uboot"
|
|
hint.map.0.readonly=1
|
|
|
|
# 64KB
|
|
hint.map.1.at="flash/spi0"
|
|
hint.map.1.start=0x00040000
|
|
hint.map.1.end=0x00050000
|
|
hint.map.1.name="uboot-env"
|
|
hint.map.1.readonly=0
|
|
|
|
# 1600KB
|
|
hint.map.2.at="flash/spi0"
|
|
hint.map.2.start=0x00050000
|
|
hint.map.2.end=0x001e0000
|
|
hint.map.2.name="kernel"
|
|
hint.map.2.readonly=0
|
|
|
|
# 14336KB
|
|
hint.map.3.at="flash/spi0"
|
|
hint.map.3.start=0x001e0000
|
|
hint.map.3.end=0x00fe0000
|
|
hint.map.3.name="rootfs"
|
|
hint.map.3.readonly=0
|
|
|
|
# NVRAM
|
|
hint.map.4.at="flash/spi0"
|
|
hint.map.4.start=0x00fe0000
|
|
hint.map.4.end=0x00ff0000
|
|
hint.map.4.name="cfg"
|
|
hint.map.4.readonly=0
|
|
|
|
# This is radio calibration section. It is (or should be!) unique
|
|
# for each board, to take into account thermal and electrical differences
|
|
# as well as the regulatory compliance data.
|
|
#
|
|
hint.map.5.at="flash/spi0"
|
|
hint.map.5.start=0x00ff0000
|
|
hint.map.5.end=0x01000000
|
|
hint.map.5.name="art"
|
|
hint.map.5.readonly=1
|
|
|
|
# GPIO specific configuration block
|
|
|
|
# Don't flip on anything that isn't already enabled.
|
|
# This includes leaving the SPI CS1/CS2 pins as GPIO pins as they're
|
|
# not used here.
|
|
hint.gpio.0.function_set=0x00000000
|
|
hint.gpio.0.function_clear=0x00000000
|
|
|
|
# These are the GPIO LEDs and buttons which can be software controlled.
|
|
#hint.gpio.0.pinmask=0x001c02ae
|
|
#hint.gpio.0.pinmask=0x00001803
|
|
|
|
# XXX TODO: the button and LEDs!
|
|
|