mirror of
https://git.FreeBSD.org/src.git
synced 2024-12-23 11:18:54 +00:00
141 lines
3.6 KiB
Plaintext
141 lines
3.6 KiB
Plaintext
# $FreeBSD$
|
|
|
|
# arge0 is connected to the LAN side of the switch PHY.
|
|
# arge1 is connected to the single port WAN side of the switch PHY.
|
|
|
|
hint.arge.0.phymask=0x0
|
|
hint.arge.0.media=1000
|
|
hint.arge.0.fduplex=1
|
|
hint.arge.0.eeprommac=0x1f66ffa0
|
|
hint.arge.0.readascii=1
|
|
|
|
hint.arge.1.phymask=0x0
|
|
hint.arge.1.media=1000
|
|
hint.arge.1.fduplex=1
|
|
hint.arge.1.eeprommac=0x1f66ffb4
|
|
hint.arge.1.readascii=1
|
|
|
|
# ath0 - slot 17
|
|
hint.pcib.0.bus.0.17.0.ath_fixup_addr=0x1f661000
|
|
hint.pcib.0.bus.0.17.0.ath_fixup_size=4096
|
|
|
|
# ath1 - slot 18
|
|
hint.pcib.0.bus.0.18.0.ath_fixup_addr=0x1f665000
|
|
hint.pcib.0.bus.0.18.0.ath_fixup_size=4096
|
|
|
|
# .. and now, telling each ath(4) NIC where to find the firmware
|
|
# image.
|
|
hint.ath.0.eeprom_firmware="pcib.0.bus.0.17.0.eeprom_firmware"
|
|
hint.ath.1.eeprom_firmware="pcib.0.bus.0.18.0.eeprom_firmware"
|
|
|
|
# Geom MAP
|
|
|
|
# The DIR-825B1 has an 8MB flash part - HOWEVER, the 64k caldata isn't
|
|
# at the end of the flash. It's ~ 6MB into the flash image.
|
|
|
|
# mtdparts=ar7100-nor0:256k(uboot),64k(Config),1024k(vmlinux),5184k(rootfs),
|
|
# 64k(caldata)
|
|
|
|
hint.map.0.at="flash/spi0"
|
|
hint.map.0.start=0x00000000
|
|
hint.map.0.end=0x000040000
|
|
hint.map.0.name="uboot"
|
|
hint.map.0.readonly=1
|
|
|
|
# This config partition is the D-Link specific configuration area.
|
|
# I'm re-purposing it for FreeBSD.
|
|
hint.map.1.at="flash/spi0"
|
|
hint.map.1.start=0x00040000
|
|
hint.map.1.end=0x00050000
|
|
hint.map.1.name="cfg"
|
|
hint.map.1.readonly=0
|
|
|
|
hint.map.2.at="flash/spi0"
|
|
hint.map.2.start=0x0050000
|
|
hint.map.2.end=0x00150000
|
|
hint.map.2.name="kernel"
|
|
hint.map.2.readonly=1
|
|
|
|
hint.map.3.at="flash/spi0"
|
|
hint.map.3.start=0x00150000
|
|
hint.map.3.end=0x00660000
|
|
hint.map.3.name="rootfs"
|
|
hint.map.3.readonly=0
|
|
|
|
hint.map.4.at="flash/spi0"
|
|
hint.map.4.start=0x00660000
|
|
hint.map.4.end=0x00670000
|
|
hint.map.4.name="art"
|
|
hint.map.4.readonly=1
|
|
|
|
# GPIO specific configuration block
|
|
|
|
# Don't flip on anything that isn't already enabled.
|
|
# This includes leaving the SPI CS1/CS2 pins as GPIO pins as they're
|
|
# not used here.
|
|
hint.gpio.0.function_set=0x00000000
|
|
|
|
hint.gpio.0.function_clear=0x00000000
|
|
|
|
# These are the GPIO LEDs and buttons which can be software controlled.
|
|
hint.gpio.0.pinmask=0x000009ff
|
|
|
|
# Pin 1 - USB (LED blue) --> works
|
|
# Pin 2 - Power (LED orange) --> works
|
|
# Pin 3 - Power (LED blue) --> works
|
|
# Pin 4 - Button (RESET) --> works
|
|
# Pin 5 - WPS (LED blue) --> works
|
|
# Pin 6 - RTL8366RB switch data line
|
|
# Pin 7 - Planet (LED orange)--> works
|
|
# Pin 8 - RTL8366RB switch clock line
|
|
# Pin 9 - Button (WPS) --> works after set to high
|
|
# Pin 10 - N/C
|
|
# Pin 11 - N/C
|
|
# Pin 12 - Planet (LED blue) --> works
|
|
|
|
# LEDs are configured separately and driven by the LED device
|
|
# usb tested good
|
|
hint.gpioled.0.at="gpiobus0"
|
|
hint.gpioled.0.name="usb-blue"
|
|
hint.gpioled.0.pins=0x0001
|
|
|
|
# no orange power led?
|
|
hint.gpioled.1.at="gpiobus0"
|
|
hint.gpioled.1.name="power-orange"
|
|
hint.gpioled.1.pins=0x0002
|
|
|
|
# blue power tested good
|
|
hint.gpioled.2.at="gpiobus0"
|
|
hint.gpioled.2.name="power-blue"
|
|
hint.gpioled.2.pins=0x0004
|
|
|
|
# wps tested good
|
|
hint.gpioled.3.at="gpiobus0"
|
|
hint.gpioled.3.name="wps-blue"
|
|
hint.gpioled.3.pins=0x0010
|
|
|
|
# orage globe tested good
|
|
hint.gpioled.4.at="gpiobus0"
|
|
hint.gpioled.4.name="planet-orange"
|
|
hint.gpioled.4.pins=0x0040
|
|
|
|
# no blue planet LED on this unit
|
|
hint.gpioled.5.at="gpiobus0"
|
|
hint.gpioled.5.name="planet-blue"
|
|
hint.gpioled.5.pins=0x0800
|
|
|
|
# GPIO I2C bus
|
|
hint.gpioiic.0.at="gpiobus0"
|
|
hint.gpioiic.0.pins=0x00a0
|
|
hint.gpioiic.0.sda=0
|
|
hint.gpioiic.0.scl=1
|
|
|
|
# I2C bus
|
|
# Don't be strict about I2C protocol - the relaxed semantics are required
|
|
# by the realtek switch PHY.
|
|
hint.iicbus.0.strict=0
|
|
|
|
# Bit bang bus - override default delay
|
|
#hint.iicbb.0.udelay=3
|
|
|