1
0
mirror of https://git.FreeBSD.org/src.git synced 2024-12-24 11:29:10 +00:00
freebsd/sys/mips/conf/PB47.hints
Adrian Chadd 38192bfc9f Add a configuration file for the Atheros PB47 reference board.
This is an AR71xx based board with 8MB flash, 64MB RAM, a
Mini-PCI+ slot (see below) and a single 10/100/1000baseT
ethernet port.  It also has two USB ports.

This is an easier board than most to add as it doesn't have a
switch PHY on-board.  This made it (mostly) trivial to craft a
working configuration.

Things to note:

* This, like most other reference boards, use uboot rather then
  redboot.  It means that you typically have to manually flash
  both the kernel and rootfs partitions.

* Since there's currently no (nice) way to extract out the
  ethernet MAC and RAM from the uboot environment, the RAM
  will default to 32mb and the MAC will be something very
  incorrect.   I'll try to fix this up in a subsequent commit
  or two, even if it's just some hard-coded nonsense in
  ar71xx_machdep.c for now.

* The board is designed for a specific model of mini-PCI+
  NIC which never made it into production.  Normal mini-PCI
  NICs will work fine; if you happen to have the NIC in question
  then it will work fine with this board.
2011-12-30 09:48:35 +00:00

80 lines
1.9 KiB
Plaintext

# $FreeBSD$
# There's two interfaces, but only one socket is populated.
#
# There's an AR8021 PHY attached to arge1.
#
# XXX TODO: figure out where to extract the MAC from.
hint.arge.1.phymask=0x01
# XXX TODO: pass in hints for the GPIO -> LED mapping for the
# minipci slot. The specific customer reference design NIC
# wires GPIO5 from each AR9220 to one of two GPIO pins on the
# MiniPCI bus. However, this may be very specific to the NIC
# being used.
# The default flash layout:
# uboot: 192k
# env: 64k
# rootfs: 6144k
# uimage (kernel): 1728k
# caldata: 64k
#
# We steal 64k from the end of rootfs to store the local config.
hint.map.0.at="flash/spi0"
hint.map.0.start=0x00000000
hint.map.0.end=0x000030000
hint.map.0.name="uboot"
hint.map.0.readonly=1
hint.map.1.at="flash/spi0"
hint.map.1.start=0x00030000
hint.map.1.end=0x00040000
hint.map.1.name="uboot-env"
hint.map.1.readonly=1
hint.map.2.at="flash/spi0"
hint.map.2.start=0x00040000
hint.map.2.end=0x00630000
hint.map.2.name="rootfs"
hint.map.2.readonly=1
hint.map.3.at="flash/spi0"
hint.map.3.start=0x00630000
hint.map.3.end=0x00640000
hint.map.3.name="cfg"
hint.map.3.readonly=0
hint.map.4.at="flash/spi0"
hint.map.4.start=0x00640000
hint.map.4.end=0x007f0000
hint.map.4.name="kernel"
hint.map.4.readonly=1
hint.map.5.at="flash/spi0"
hint.map.5.start=0x007f0000
hint.map.5.end=0x00800000
hint.map.5.name="art"
hint.map.5.readonly=1
# Don't flip on anything that isn't already enabled by the
# bootloader.
hint.gpio.0.function_set=0x00000000
hint.gpio.0.function_clear=0x00000000
# Which GPIO lines to enable - just GPIO2/3 for the LEDs.
hint.gpio.0.pinmask=0x0000000c
# GPIO2 and GPIO3 are LEDs, where 0=on and 1=off.
# XXX TODO: teach gpioled about polarity?
hint.gpioled.0.at="gpiobus0"
hint.gpioled.0.pins="0x0004"
hint.gpioled.0.name="led1"
hint.gpioled.1.at="gpiobus0"
hint.gpioled.1.pins="0x0008"
hint.gpioled.1.name="led2"