mirror of
https://git.FreeBSD.org/src.git
synced 2024-12-25 11:37:56 +00:00
325 lines
10 KiB
Groff
325 lines
10 KiB
Groff
.\" $FreeBSD$
|
|
.Dd December 2, 1994
|
|
.Dt CXCONFIG 8
|
|
.Os FreeBSD
|
|
.Sh NAME
|
|
.Nm cxconfig
|
|
.Nd channel options management utility for Cronyx-Sigma adapter
|
|
.Sh SYNOPSIS
|
|
.Nm cxconfig
|
|
.Op Fl a
|
|
.Op Ar <channel> Op Ar <option>...
|
|
.Sh DESCRIPTION
|
|
The
|
|
.Nm
|
|
utility is used for configuring the channel options of
|
|
the Cronyx-Sigma adapter.
|
|
.Pp
|
|
To change channel options the channel should be free: the corresponding
|
|
network interface in ``down'' state, the asynchronous terminal device
|
|
.Pa /dev/tty*
|
|
closed.
|
|
Generally, the channel options are set up during the operating
|
|
system startup, for example from the
|
|
.Pa /etc/rc
|
|
file.
|
|
.Pp
|
|
Note, that not all options have a sense for every particular
|
|
case, and an attempt to set some of them can hang up the channel or
|
|
the whole adapter.
|
|
.Pp
|
|
The following option is available:
|
|
.Bl -tag -width indent
|
|
.It Fl a
|
|
Display full information.
|
|
.El
|
|
.Sh "Channel options"
|
|
.Bl -tag -width 10n
|
|
.It ispeed=#
|
|
Set the receiver baud rate to the number given.
|
|
The maximal value is 256000 bits/sec.
|
|
In the synchronous mode the receiver baud rate is significant
|
|
only when DPLL mode is used.
|
|
.It ospeed=#
|
|
Set the transmitter baud rate to the number given.
|
|
The maximal value is 256000 bits/sec.
|
|
In the synchronous mode the transmitter baud rate is significant
|
|
only in the case of the internal clock source.
|
|
If receiver and transmitter have equal data rate, then it could
|
|
be set by specifying only the numerical argument.
|
|
.It async
|
|
Set the asynchronous channel mode.
|
|
.It "hdlc, bisync, bsc, x.21, x21
|
|
Set the synchronous channel mode: HDLC, Bisync (BSC) or X.21.
|
|
.It ppp
|
|
Set the link-level protocol: PpP/HDLC. The built-in simplified synchronous PPP
|
|
implementation is used (see RFC-1548, RFC-1549).
|
|
.It cisco
|
|
Set the link-level protocol: Cisco/HDLC (see RFC-1547).
|
|
This protocol is intended for compatibility with old models of Cisco routers,
|
|
and with early versions of BSD/386 drivers.
|
|
The extensive usage of this protocol is not recommended.
|
|
.It ext
|
|
Use the external link-level protocol suite (for BSD/386 only).
|
|
.It "+keepalive, -keepalive"
|
|
Enable the automatic line state control sub-protocol.
|
|
This setting is not significant when the external link-level protocol is used.
|
|
.It "+autorts, -autorts"
|
|
Enable the automatic RTS signal control.
|
|
When enabled, the RTS signal goes up only when both halves of
|
|
the receiver ring buffer are free and ready for receive,
|
|
and goes down when one or both buffers are busy.
|
|
.It "port=rs232, port=rs449, port=v35
|
|
Set the zero channel hardware interface type.
|
|
.El
|
|
.Sh "Common options"
|
|
.Bl -tag -width 10n
|
|
.It "nrz, nrzi, manchester"
|
|
Set the data line signal encoding.
|
|
In the case of
|
|
.Em NRZ
|
|
encoding the zero bit is transmitted by the zero signal
|
|
level, the one bit - by the positive signal level.
|
|
In the case of
|
|
.Em NRZI
|
|
encoding the zero bit is transmitted by the change of
|
|
the signal level, the one bit - by the constant signal level.
|
|
In the case of
|
|
.Em Manchester
|
|
encoding the zero bit is encoded as 01 value,
|
|
the one bit - as 10 value.
|
|
.It "+dpll, -dpll"
|
|
Enable the digital phase locked loop mode (DPLL).
|
|
When enabled, the receiver timing clock signal
|
|
is derived from the received data.
|
|
.It "+lloop, -lloop"
|
|
Set the local loopback mode.
|
|
.It "+extclock, -extclock"
|
|
Set the timing clock source of synchronous channels. There are
|
|
two possible variants:
|
|
.Em "external clock"
|
|
source or
|
|
.Em "internal clock"
|
|
generation.
|
|
.Pp
|
|
.Em "External clock"
|
|
mode is the most common method for connecting
|
|
external modem hardware. In this mode the external timing
|
|
signal is received on TXCIN pin of the connector, and it is
|
|
used as a synchronization clock for transmitting data (TXD).
|
|
.Pp
|
|
In the case of
|
|
.Em "internal clock"
|
|
mode the transmitted data (TXD)
|
|
are synchronized using the internal on-board timing generator,
|
|
the internally generated timing signal is driven on the TXCOUT
|
|
pin, and the signal on the TXCIN pin is ignored. This mode
|
|
is used for direct terminal-to-terminal communication,
|
|
e.g. for connecting two computers together in a synchronous mode
|
|
via relatively short cable. This method should also be used
|
|
for testing channels with an external loopback connector.
|
|
.It fifo=#
|
|
FIFO threshold level setup for receiver and transmitter.
|
|
.It rfifo=#
|
|
Hardware RTS/CTS flow control FIFO threshold setup.
|
|
.It "+ctsup, -ctsup"
|
|
Enable/disable interrupts on CTS (Clear To Send) signal setup (0 to 1 transition).
|
|
.It "+ctsdown, -ctsdown"
|
|
Enable/disable interrupts on CTS (Clear To Send) signal clear (1 to 0 transition).
|
|
.It "+cdup, -cdup"
|
|
Enable/disable interrupts on CD (Carrier Detect) signal setup (0 to 1 transition).
|
|
.It "+cddown, -cddown"
|
|
Enable/disable interrupts on CD (Carrier Detect) signal clear (1 to 0 transition).
|
|
.It "+dsrup, -dsrup"
|
|
Enable/disable interrupts on DSR (Data Set Ready) signal setup (0 to 1 transition).
|
|
.It "+dsrdown, -dsrdown"
|
|
Enable/disable interrupts on DSR (Data Set Ready) signal clear (1 to 0 transition).
|
|
.El
|
|
.Sh "Asynchronous mode options"
|
|
.Bl -tag -width 10n
|
|
.It cs#
|
|
Select character size: 5, 6, 7 or 8 bits.
|
|
.It "parodd, pareven
|
|
Parity mode: odd or even.
|
|
.It "+ignpar, -ignpar
|
|
Disable/enable parity detection.
|
|
.It nopar
|
|
Disable parity bit generation.
|
|
.It forcepar
|
|
Force parity: even - 0, odd - 1.
|
|
.It "stopb1, stopb1.5, stopb2
|
|
Use 1 or 1.5 or 2 stop bits per character.
|
|
.It "+dsr, -dsr"
|
|
Use the DSR input signal as receiver enable/disable.
|
|
.It "+cts, -cts"
|
|
Use the CTS input signal as transmitter enable/disable.
|
|
.It "+rts, -rts"
|
|
Drive the RTS output signal as transmitter ready.
|
|
.It "+rloop, -rloop"
|
|
Set the remote loopback mode.
|
|
.It "+etc, -etc"
|
|
Enable the embedded transmit commands mode.
|
|
.It "+ixon, -ixon"
|
|
Enable the hardware XON/XOFF flow control support.
|
|
.It "+ixany, -ixany"
|
|
Use the hardware IXANY mode support.
|
|
.It "+sdt, -sdt"
|
|
Detect the spec. characters SCHR1 and SCHR2 in the receive data.
|
|
.It "+flowct, -flowct"
|
|
Receive the flow control spec. characters as data.
|
|
.It "+rdt, -rdt"
|
|
Detect the spec. characters in range SCRL..SCRH in the receive data.
|
|
.It "+exdt, -exdt"
|
|
Detect the spec. characters SCHR3 and SCHR4 in the receive data.
|
|
.It "parintr, parnull, parign, pardisc, parffnull
|
|
Action on parity errors:
|
|
.Pp
|
|
.Bl -tag -width parffnullxxx -compact
|
|
.It Mode
|
|
Action
|
|
.It parintr
|
|
Generate the receiver error interrupt
|
|
.It parnull
|
|
Input the NUL character
|
|
.It parign
|
|
Ignore the error, receive as good data
|
|
.It pardisc
|
|
Ignore the character
|
|
.It parffnull
|
|
Input the sequence <0xFF, NUL, character>
|
|
.El
|
|
.It "brkintr, brknull, brkdisc
|
|
Line break state action:
|
|
.Pp
|
|
.Bl -tag -width parffnullxxx -compact
|
|
.It Mode
|
|
Action
|
|
.It brkintr
|
|
Generate the receiver error interrupt
|
|
.It brknull
|
|
Input the NUL character
|
|
.It brkdisc
|
|
Ignore the line break state
|
|
.El
|
|
.It "+inlcr, -inlcr"
|
|
Translate received NL characters to CR.
|
|
.It "+icrnl, -icrnl"
|
|
Translate received CR characters to NL.
|
|
.It "+igncr, -igncr"
|
|
Ignore received CR characters.
|
|
.It "+ocrnl, -ocrnl"
|
|
Translate transmitted CR characters to NL.
|
|
.It "+onlcr, -onlcr"
|
|
Translate transmitted NL characters to CR.
|
|
.It "+fcerr, -fcerr"
|
|
Process (don't process) the characters, received with errors,
|
|
for special character/flow control matching.
|
|
.It "+lnext, -lnext"
|
|
Enable the LNEXT character option: the character following
|
|
the LNEXT character is not processed for special character/flow
|
|
control matching.
|
|
.It "+istrip, -istrip"
|
|
Strip input characters to seven bits.
|
|
.It schr1=#
|
|
The XON flow control character value.
|
|
.It schr2=#
|
|
The XOFF flow control character value.
|
|
.It schr3=#
|
|
The SCHR3 spec. character value.
|
|
.It schr4=#
|
|
The SCHR4 spec. character value.
|
|
.It "scrl=#, scrh=#
|
|
The spec. character range (inclusive).
|
|
.It lnext=#
|
|
The LNEXT spec. character value.
|
|
.El
|
|
.Sh "HDLC mode options"
|
|
.Bl -tag -width 10n
|
|
.It if#
|
|
The minimum number of flags transmitted before a frame is started.
|
|
.It noaddr
|
|
No frame address recognition.
|
|
.It "addrlen1, addrlen2"
|
|
Address field length: 1 or 2 bytes.
|
|
.It "addr1, addr2"
|
|
Addressing mode: 4x1 bytes or 2x2 bytes.
|
|
Registers RFAR1..RFAR4 should contain the address to be matched.
|
|
.It "+clrdet, -clrdet"
|
|
Enable/disable clear detect for X.21 protocol support.
|
|
.It "+dsr, -dsr"
|
|
Use the DSR input signal as receiver enable/disable.
|
|
.It "+cts, -cts"
|
|
Use the CTS input signal as transmitter enable/disable.
|
|
.It "+rts, -rts"
|
|
Drive the RTS output signal as transmitter ready.
|
|
.It "+fcs, -fcs"
|
|
Enable/disable the frame checksum generation and checking.
|
|
.It "crc-16, crc-v.41
|
|
Select the CRC polynomial: CRC-16 (x^16+x^15+x^2+1)
|
|
or CRC V.41 (x^16+x^12+x^5+1).
|
|
.It "fcs-crc-16, fcs-v.41
|
|
Frame checksum preset: all zeros (CRC-16) or all ones (CRC V.41).
|
|
.It "+crcinv, -crcinv"
|
|
Invert (ie. CRC V.41) or don't invert (ie. CRC-16) the transmitted frame checksum.
|
|
.It "+fcsapd, -fcsapd"
|
|
Pass the received CRC to the host at the end of receiver data buffer.
|
|
.It "idlemark, idleflag
|
|
Idle mode: idle in mark (transmit all ones) or idle in flag (transmit flag).
|
|
.It "+syn, -syn"
|
|
Enable/disable sending pad characters before sending flag when coming out
|
|
of the idle mode.
|
|
.It pad#
|
|
The number of synchronous characters sent (0..4).
|
|
.It "syn=0xaa, syn=0x00
|
|
Send sync pattern.
|
|
.It "rfar1=#, rfar2=#, rfar3=#, rfar4=#
|
|
Frame address registers for address recognition.
|
|
.El
|
|
.Sh EXAMPLES
|
|
Set up the channel 7 of the adapter Sigma-400 under
|
|
.Bx Free .
|
|
Physical 4-wire leased line with Zelax+ M115 short-range modems.
|
|
Synchronous mode, 128000 bits/sec, interface RS-232,
|
|
protocol PpP/HDLC without keepalive support, NRZI encoding,
|
|
DPLL mode, no flow control:
|
|
.Bd -literal
|
|
cxconfig cx7 128000 hdlc ppp -keepalive nrzi -cts +dpll -extclock
|
|
ifconfig cx7 158.250.244.2 158.250.244.1 up
|
|
.Ed
|
|
.Pp
|
|
Set up the channel 0 of the adapter Sigma-100 under
|
|
.Bx Free .
|
|
Attachment to the near computer by short cable, internal clock source.
|
|
Synchronous mode, 256000 bits/sec, interface RS-232,
|
|
protocol Cisco/HDLC with keepalive support:
|
|
.Bd -literal
|
|
cxconfig cx0 hdlc 256000 cisco +keepalive -extclock
|
|
ifconfig cx0 200.1.1.1 200.1.1.2 up
|
|
.Ed
|
|
.Pp
|
|
Set up the channel 1 of the adapter Sigma-840 under BSD/386.
|
|
Synchronous 64 kbit/sec leased line, external clock source.
|
|
Synchronous mode, interface V.35, external protocol suite:
|
|
.Bd -literal
|
|
cxconfig cx1 hdlc ext
|
|
ifconfig cx1 193.124.254.50 193.124.254.49 multicast up
|
|
.Ed
|
|
.Pp
|
|
Set up the channel 0 of the adapter Sigma-840 under
|
|
.Bx Free .
|
|
Attachment to the Cisco-4000 router by null-modem cable, internal clock source.
|
|
Synchronous mode, 64000 bits/sec, interface RS-232,
|
|
protocol PpP/HDLC with keepalive support and flow control,
|
|
LCP and IPCP protocols (see RFC-1548 and RFC-1332) debug tracing enabled:
|
|
.Bd -literal
|
|
cxconfig cx0 hdlc 64000 port=rs232 ppp +keepalive -extclock +cts
|
|
ifconfig cx0 100.0.0.2 100.0.0.1 debug up
|
|
.Ed
|
|
.Sh FILES
|
|
.Bl -tag -width /dev/cronyx -compact
|
|
.Pa /dev/cronyx
|
|
the special device file for adapter options management
|
|
.El
|
|
.Sh SEE ALSO
|
|
.Xr cx 4
|