1
0
mirror of https://git.FreeBSD.org/src.git synced 2024-12-05 09:14:03 +00:00
freebsd/sys/dev/ic/z8530.h
Marcel Moolenaar 1ba1685b25 MFp4:
Add CHAN_A & CHAN_B for channel register offsets.
While here, fix a comment.
2006-02-24 02:03:35 +00:00

256 lines
10 KiB
C

/*-
* Copyright (c) 2003 Marcel Moolenaar
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
*
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
*
* THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR
* IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
* OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
* IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
* NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
* DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
* THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
* THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*
* $FreeBSD$
*/
#ifndef _DEV_IC_Z8530_H_
#define _DEV_IC_Z8530_H_
/*
* Channel B control: 0
* Channel B data: 1
* Channel A control: 2
* Channel A data: 3
*/
/* The following apply when using a device-scoped bus handle */
#define CHAN_A 2
#define CHAN_B 0
#define REG_CTRL 0
#define REG_DATA 1
/* Write registers. */
#define WR_CR 0 /* Command Register. */
#define WR_IDT 1 /* Interrupt and Data Transfer Mode. */
#define WR_IV 2 /* Interrupt Vector (shared). */
#define WR_RPC 3 /* Receive Parameters and Control. */
#define WR_MPM 4 /* Miscellaneous Parameters and Modes. */
#define WR_TPC 5 /* Transmit Parameters and Control. */
#define WR_SCAF 6 /* Sync Character or (SDLC) Address Field. */
#define WR_SCF 7 /* Sync Character or (SDCL) Flag. */
#define WR_EFC 7 /* Extended Feature and FIFO Control. */
#define WR_TB 8 /* Transmit Buffer. */
#define WR_MIC 9 /* Master Interrupt Control (shared). */
#define WR_MCB1 10 /* Miscellaneous Control Bits (part 1 :-). */
#define WR_CMC 11 /* Clock Mode Control. */
#define WR_TCL 12 /* BRG Time Constant Low. */
#define WR_TCH 13 /* BRG Time Constant High. */
#define WR_MCB2 14 /* Miscellaneous Control Bits (part 2 :-). */
#define WR_IC 15 /* Interrupt Control. */
/* Read registers. */
#define RR_BES 0 /* Buffer and External Status. */
#define RR_SRC 1 /* Special Receive Condition. */
#define RR_IV 2 /* Interrupt Vector. */
#define RR_IP 3 /* Interrupt Pending (ch A only). */
#define RR_MPM 4 /* Miscellaneous Parameters and Modes. */
#define RR_TPC 5 /* Transmit Parameters and Control. */
#define RR_BCL 6 /* Byte Count Low. */
#define RR_BCH 7 /* Byte Count High. */
#define RR_RB 8 /* Receive Buffer. */
#define RR_RPC 9 /* Receive Parameters and Control. */
#define RR_MSB 10 /* Miscellaneous Status Bits. */
#define RR_MCB1 11 /* Miscellaneous Control Bits (part 1). */
#define RR_TCL 12 /* BRG Time Constant Low. */
#define RR_TCH 13 /* BRG Time Constant High. */
#define RR_EFC 14 /* Extended Feature and FIFO Control. */
#define RR_IC 15 /* Interrupt Control. */
/* Buffer and External Status (RR0). */
#define BES_BRK 0x80 /* Break (Abort). */
#define BES_TXU 0x40 /* Tx Underrun (EOM). */
#define BES_CTS 0x20 /* CTS. */
#define BES_SYNC 0x10 /* Sync. */
#define BES_DCD 0x08 /* DCD. */
#define BES_TXE 0x04 /* Tx Empty. */
#define BES_ZC 0x02 /* Zero Count. */
#define BES_RXA 0x01 /* Rx Available. */
/* Clock Mode Control (WR11). */
#define CMC_XTAL 0x80 /* -RTxC connects to quartz crystal. */
#define CMC_RC_DPLL 0x60 /* Rx Clock from DPLL. */
#define CMC_RC_BRG 0x40 /* Rx Clock from BRG. */
#define CMC_RC_TRXC 0x20 /* Rx Clock from -TRxC. */
#define CMC_RC_RTXC 0x00 /* Rx Clock from -RTxC. */
#define CMC_TC_DPLL 0x18 /* Tx Clock from DPLL */
#define CMC_TC_BRG 0x10 /* Tx Clock from BRG */
#define CMC_TC_TRXC 0x08 /* Tx Clock from -TRxC. */
#define CMC_TC_RTXC 0x00 /* Tx Clock from -RTxC. */
#define CMC_TRXC_OUT 0x04 /* -TRxC is output. */
#define CMC_TRXC_DPLL 0x03 /* -TRxC from DPLL */
#define CMC_TRXC_BRG 0x02 /* -TRxC from BRG */
#define CMC_TRXC_XMIT 0x01 /* -TRxC from Tx clock. */
#define CMC_TRXC_XTAL 0x00 /* -TRxC from XTAL. */
/* Command Register (WR0). */
#define CR_RSTTXU 0xc0 /* Reset Tx. Underrun/EOM. */
#define CR_RSTTXCRC 0x80 /* Reset Tx. CRC. */
#define CR_RSTRXCRC 0x40 /* Reset Rx. CRC. */
#define CR_RSTIUS 0x38 /* Reset Int. Under Service. */
#define CR_RSTERR 0x30 /* Error Reset. */
#define CR_RSTTXI 0x28 /* Reset Tx. Int. */
#define CR_ENARXI 0x20 /* Enable Rx. Int. */
#define CR_ABORT 0x18 /* Send Abort. */
#define CR_RSTXSI 0x10 /* Reset Ext/Status Int. */
/* Extended Feature and FIFO Control (WR7 prime). */
#define EFC_ERE 0x40 /* Extended Read Enable. */
#define EFC_FE 0x20 /* Transmit FIFO Empty. */
#define EFC_RQT 0x10 /* Request Timing. */
#define EFC_FHF 0x08 /* Receive FIFO Half Full. */
#define EFC_RTS 0x04 /* Auto RTS Deactivation. */
#define EFC_EOM 0x02 /* Auto EOM Reset. */
#define EFC_FLAG 0x01 /* Auto SDLC Flag on Tx. */
/* Interrupt Control (WR15). */
#define IC_BRK 0x80 /* Break (Abort) IE. */
#define IC_TXU 0x40 /* Tx Underrun IE. */
#define IC_CTS 0x20 /* CTS IE. */
#define IC_SYNC 0x10 /* Sync IE. */
#define IC_DCD 0x08 /* DCD IE. */
#define IC_FIFO 0x04 /* SDLC FIFO Enable. */
#define IC_ZC 0x02 /* Zero Count IE. */
#define IC_EF 0x01 /* Extended Feature Enable. */
/* Interrupt and Data Transfer Mode (WR1). */
#define IDT_WRE 0x80 /* Wait/DMA Request Enable. */
#define IDT_REQ 0x40 /* DMA Request. */
#define IDT_WRR 0x20 /* Wait/DMA Reuest on Receive. */
#define IDT_RISC 0x18 /* Rx Int. on Special Condition Only. */
#define IDT_RIA 0x10 /* Rx Int. on All Characters. */
#define IDT_RIF 0x08 /* Rx Int. on First Character. */
#define IDT_PSC 0x04 /* Parity is Special Condition. */
#define IDT_TIE 0x02 /* Tx Int. Enable. */
#define IDT_XIE 0x01 /* Ext. Int. Enable. */
/* Interrupt Pending (RR3). */
#define IP_RIA 0x20 /* Rx. Int. ch. A. */
#define IP_TIA 0x10 /* Tx. Int. ch. A. */
#define IP_SIA 0x08 /* Ext/Status Int. ch. A. */
#define IP_RIB 0x04 /* Rx. Int. ch. B. */
#define IP_TIB 0x02 /* Tx. Int. ch. B. */
#define IP_SIB 0x01 /* Ext/Status Int. ch. B. */
/* Interrupt Vector Status Low (RR2). */
#define IV_SCA 0x0e /* Special Condition ch. A. */
#define IV_RAA 0x0c /* Receive Available ch. A. */
#define IV_XSA 0x0a /* External/Status Change ch. A. */
#define IV_TEA 0x08 /* Transmitter Empty ch. A. */
#define IV_SCB 0x06 /* Special Condition ch. B. */
#define IV_RAB 0x04 /* Receive Available ch. B. */
#define IV_XSB 0x02 /* External/Status Change ch. B. */
#define IV_TEB 0x00 /* Transmitter Empty ch. B. */
/* Miscellaneous Control Bits part 1 (WR10). */
#define MCB1_CRC1 0x80 /* CRC presets to 1. */
#define MCB1_FM0 0x60 /* FM0 Encoding. */
#define MCB1_FM1 0x40 /* FM1 Encoding. */
#define MCB1_NRZI 0x20 /* NRZI Encoding. */
#define MCB1_NRZ 0x00 /* NRZ Encoding. */
#define MCB1_AOP 0x10 /* Active On Poll. */
#define MCB1_MI 0x08 /* Mark Idle. */
#define MCB1_AOU 0x04 /* Abort On Underrun. */
#define MCB1_LM 0x02 /* Loop Mode. */
#define MCB1_SIX 0x01 /* 6 or 12 bit SYNC. */
/* Miscellaneous Control Bits part 2 (WR14). */
#define MCB2_NRZI 0xe0 /* DPLL - NRZI mode. */
#define MCB2_FM 0xc0 /* DPLL - FM mode. */
#define MCB2_RTXC 0xa0 /* DPLL - Clock from -RTxC. */
#define MCB2_BRG 0x80 /* DPLL - Clock from BRG. */
#define MCB2_OFF 0x60 /* DPLL - Disable. */
#define MCB2_RMC 0x40 /* DPLL - Reset Missing Clock. */
#define MCB2_ESM 0x20 /* DPLL - Enter Search Mode. */
#define MCB2_LL 0x10 /* Local Loopback. */
#define MCB2_AE 0x08 /* Auto Echo. */
#define MCB2_REQ 0x04 /* Request Function. */
#define MCB2_PCLK 0x02 /* BRG source is PCLK. */
#define MCB2_BRGE 0x01 /* BRG enable. */
/* Master Interrupt Control (WR9). */
#define MIC_FHR 0xc0 /* Force Hardware Reset. */
#define MIC_CRA 0x80 /* Channel Reset A. */
#define MIC_CRB 0x40 /* Channel Reset B. */
#define MIC_SIE 0x20 /* Software INTACK Enable. */
#define MIC_SH 0x10 /* Status High. */
#define MIC_MIE 0x08 /* Master Interrupt Enable. */
#define MIC_DLC 0x04 /* Disable Lower Chain. */
#define MIC_NV 0x02 /* No Vector. */
#define MIC_VIS 0x01 /* Vector Includes Status. */
/* Transmit/Receive Miscellaneous Parameters and Modes (WR4). */
#define MPM_CM64 0xc0 /* X64 Clock Mode. */
#define MPM_CM32 0x80 /* X32 Clock Mode. */
#define MPM_CM16 0x40 /* X16 Clock Mode. */
#define MPM_CM1 0x00 /* X1 Clock Mode. */
#define MPM_EXT 0x30 /* External Sync Mode. */
#define MPM_SDLC 0x20 /* SDLC mode. */
#define MPM_BI 0x10 /* 16-bit Sync (bi-sync). */
#define MPM_MONO 0x00 /* 8-bit Sync (mono-sync). */
#define MPM_SB2 0x0c /* Async mode: 2 stopbits. */
#define MPM_SB15 0x08 /* Async mode: 1.5 stopbits. */
#define MPM_SB1 0x04 /* Async mode: 1 stopbit. */
#define MPM_SYNC 0x00 /* Sync Mode Enable. */
#define MPM_EVEN 0x02 /* Async mode: even parity. */
#define MPM_PE 0x01 /* Async mode: parity enable. */
/* Receive Parameters and Control (WR3). */
#define RPC_RB8 0xc0 /* 8 databits. */
#define RPC_RB6 0x80 /* 6 databits. */
#define RPC_RB7 0x40 /* 7 databits. */
#define RPC_RB5 0x00 /* 5 databits. */
#define RPC_AE 0x20 /* Auto Enable. */
#define RPC_EHM 0x10 /* Enter Hunt Mode. */
#define RPC_CRC 0x08 /* CRC Enable. */
#define RPC_ASM 0x04 /* Address Search Mode. */
#define RPC_LI 0x02 /* SYNC Character Load Inhibit */
#define RPC_RXE 0x01 /* Receiver Enable */
/* Special Receive Condition (RR1). */
#define SRC_EOF 0x80 /* End Of Frame. */
#define SRC_FE 0x40 /* Framing Error. */
#define SRC_OVR 0x20 /* Rx. Overrun. */
#define SRC_PE 0x10 /* Parity Error. */
#define SRC_RC0 0x08 /* Residue Code 0. */
#define SRC_RC1 0x04 /* Residue Code 1. */
#define SRC_RC2 0x02 /* Residue Code 2. */
#define SRC_AS 0x01 /* All Sent. */
/* Transmit Parameter and Control (WR5). */
#define TPC_DTR 0x80 /* DTR. */
#define TPC_TB8 0x60 /* 8 databits. */
#define TPC_TB6 0x40 /* 6 databits. */
#define TPC_TB7 0x20 /* 7 databits. */
#define TPC_TB5 0x00 /* 5 or fewer databits. */
#define TPC_BRK 0x10 /* Send break. */
#define TPC_TXE 0x08 /* Transmitter Enable. */
#define TPC_CRC16 0x04 /* CRC16. */
#define TPC_RTS 0x02 /* RTS. */
#define TPC_CRC 0x01 /* CRC Enable. */
#endif /* _DEV_IC_Z8530_H_ */