Bernhard Schmidt 759c594d37 Fix rmax calculation during BSS selection. ... If multiple networks are available the max bandwidth is one condition used for selecting the "best" BSS. To achieve that we should consider all parameters which affect the max RX rate. This includes 20/40MHz, SGI and the of course the MCS set. If the TX MCS parameters are available we should use those, because an AP announcing support for receiving frames at 450Mbps might only be able to transmit at 150Mbps (1T3R). I haven't seen devices with support for transmitting at higher rates then receiving, so prefering TX over RX information should be safe. While here, remove the hardcoded assumption that MCS15 is the max possible MCS rate, use MCS31 instead which really is the highest rate (according to the 802.11n std). Also, fix a mismatch of an 40MHz/SGI check.		2011-03-13 11:58:40 +00:00
..
_ieee80211.h	Complete the MCS rate table based on the final 802.11n std. While here	2011-03-10 18:17:24 +00:00
ieee80211_acl.c
ieee80211_action.c
ieee80211_action.h
ieee80211_adhoc.c	Make sure to only accept and handle action frames which are for us. In	2011-02-22 19:05:42 +00:00
ieee80211_adhoc.h
ieee80211_ageq.c	Fix typos - remove duplicate "is".	2011-02-23 09:22:33 +00:00
ieee80211_ageq.h
ieee80211_amrr.c
ieee80211_amrr.h
ieee80211_crypto_ccmp.c
ieee80211_crypto_none.c
ieee80211_crypto_tkip.c
ieee80211_crypto_wep.c
ieee80211_crypto.c
ieee80211_crypto.h
ieee80211_ddb.c
ieee80211_dfs.c
ieee80211_dfs.h
ieee80211_freebsd.c	Specify a CTLTYPE_FOO so that a future sysctl(8) change does not need	2011-01-18 21:14:13 +00:00
ieee80211_freebsd.h
ieee80211_hostap.c	Make sure to only accept and handle action frames which are for us. In	2011-02-22 19:05:42 +00:00
ieee80211_hostap.h
ieee80211_ht.c	Fill hc_mcsset completely.	2011-03-13 11:56:33 +00:00
ieee80211_ht.h	Complete the MCS rate table based on the final 802.11n std. While here	2011-03-10 18:17:24 +00:00
ieee80211_hwmp.c
ieee80211_input.c	Add a new mgmt subtype "ACTION NO ACK" defined in 802.11n-2009, while here	2011-02-21 19:59:43 +00:00
ieee80211_input.h
ieee80211_ioctl.c	Instead of always returning 0 to a scan request, indicate if there is	2011-01-30 14:05:21 +00:00
ieee80211_ioctl.h
ieee80211_mesh.c	Make sure to only accept and handle action frames which are for us. In	2011-02-22 19:05:42 +00:00
ieee80211_mesh.h
ieee80211_monitor.c
ieee80211_monitor.h
ieee80211_node.c
ieee80211_node.h
ieee80211_output.c	It is IEEE80211_SUPPORT_XXX not IEEE80211_XXX_SUPPORT.	2011-02-21 20:02:02 +00:00
ieee80211_phy.c
ieee80211_phy.h
ieee80211_power.c
ieee80211_power.h
ieee80211_proto.c	Add a new mgmt subtype "ACTION NO ACK" defined in 802.11n-2009, while here	2011-02-21 19:59:43 +00:00
ieee80211_proto.h
ieee80211_radiotap.c
ieee80211_radiotap.h
ieee80211_ratectl_none.c
ieee80211_ratectl.c
ieee80211_ratectl.h
ieee80211_regdomain.c
ieee80211_regdomain.h
ieee80211_rssadapt.c
ieee80211_rssadapt.h
ieee80211_scan_sta.c	Fix rmax calculation during BSS selection.	2011-03-13 11:58:40 +00:00
ieee80211_scan.c	Change return code semantics of start_scan_locked(). Instead of reporting	2011-01-30 14:00:50 +00:00
ieee80211_scan.h
ieee80211_sta.c	Make sure to only accept and handle action frames which are for us. In	2011-02-22 19:05:42 +00:00
ieee80211_sta.h
ieee80211_superg.c
ieee80211_superg.h
ieee80211_tdma.c
ieee80211_tdma.h
ieee80211_var.h	First step on removing the harcoded RX/TX stream and MCS0-15 assumptions.	2011-03-13 11:40:18 +00:00
ieee80211_wds.c	Make sure to only accept and handle action frames which are for us. In	2011-02-22 19:05:42 +00:00
ieee80211_wds.h
ieee80211_xauth.c
ieee80211.c	While determining the maxrate for ieee80211_media_setup() honor	2011-03-13 11:47:43 +00:00
ieee80211.h	Add a new mgmt subtype "ACTION NO ACK" defined in 802.11n-2009, while here	2011-02-21 19:59:43 +00:00