1
0
mirror of https://git.FreeBSD.org/src.git synced 2024-12-24 11:29:10 +00:00
freebsd/sys/pci/if_de.c
Peter Wemm 28c412b0e9 malloc() the rx and tx descriptors seperately rather than as part of the
large (over 4KB) softc struct.  The descriptor array is accessed by
busmaster dma and must be physically contiguous in memory.  malloc() of
a block greater than a page is only virtually contiguous, and not
necessarily physically contigious.

contigmalloc() could do this, but that is a bit on the overkill side.

I'm not sure of the origins of the problem report and diagnosis, I learned
of the problem via mail forwarded from  Jim Shankland <jas@flyingfox.com>.

Jim said that Matt Thomas's workaround was to reduce the number of
transmit descriptors from 128 to 32, but I was concerned that it might
cost performance.  Anyway, this change is my fault, not Jim's. :-)

Reviewed by: davidg
1997-09-11 15:27:35 +00:00

5276 lines
154 KiB
C
Raw Blame History

This file contains invisible Unicode characters

This file contains invisible Unicode characters that are indistinguishable to humans but may be processed differently by a computer. If you think that this is intentional, you can safely ignore this warning. Use the Escape button to reveal them.

/*-
* Copyright (c) 1994-1997 Matt Thomas (matt@3am-software.com)
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. The name of the author may not be used to endorse or promote products
* derived from this software withough specific prior written permission
*
* THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR
* IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
* OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
* IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
* NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
* DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
* THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
* THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*
* $Id: if_de.c,v 1.67 1997/09/02 20:06:26 bde Exp $
*
*/
/*
* DEC 21040 PCI Ethernet Controller
*
* Written by Matt Thomas
* BPF support code stolen directly from if_ec.c
*
* This driver supports the DEC DE435 or any other PCI
* board which support 21040, 21041, or 21140 (mostly).
*/
#define TULIP_HDR_DATA
#include <sys/param.h>
#include <sys/systm.h>
#include <sys/mbuf.h>
#include <sys/socket.h>
#include <sys/sockio.h>
#include <sys/malloc.h>
#include <sys/kernel.h>
#if defined(__FreeBSD__)
#include <machine/clock.h>
#elif defined(__bsdi__) || defined(__NetBSD__)
#include <sys/device.h>
#endif
#include <net/if.h>
#if defined(SIOCSIFMEDIA) && !defined(TULIP_NOIFMEDIA)
#include <net/if_media.h>
#endif
#include <net/if_dl.h>
#include <net/netisr.h>
#if defined(__bsdi__) && _BSDI_VERSION >= 199701
#include <dev/mii/mii.h>
#include <dev/mii/miivar.h>
#endif
#include "bpfilter.h"
#if NBPFILTER > 0
#include <net/bpf.h>
#endif
#ifdef INET
#include <netinet/in.h>
#endif
#ifdef NS
#include <netns/ns.h>
#include <netns/ns_if.h>
#endif
#include <vm/vm.h>
#if defined(__FreeBSD__)
#include <vm/pmap.h>
#include <pci.h>
#include <netinet/if_ether.h>
#if NPCI > 0
#include <pci/pcivar.h>
#include <pci/dc21040reg.h>
#define DEVAR_INCLUDE "pci/if_devar.h"
#endif
#endif /* __FreeBSD__ */
#if defined(__bsdi__)
#include <netinet/if_ether.h>
#include <i386/pci/ic/dc21040reg.h>
#include <i386/isa/isa.h>
#include <i386/isa/icu.h>
#include <i386/isa/dma.h>
#include <i386/isa/isavar.h>
#include <i386/pci/pci.h>
#if _BSDI_VERSION < 199510
#include <eisa.h>
#else
#define NEISA 0
#endif
#if NEISA > 0 && _BSDI_VERSION >= 199401
#include <i386/eisa/eisa.h>
#define TULIP_EISA
#endif
#define DEVAR_INCLUDE "i386/pci/if_devar.h"
#endif /* __bsdi__ */
#if defined(__NetBSD__)
#include <net/if_ether.h>
#if defined(INET)
#include <netinet/if_inarp.h>
#endif
#include <machine/bus.h>
#if defined(__alpha__)
#include <machine/intr.h>
#endif
#include <dev/pci/pcireg.h>
#include <dev/pci/pcivar.h>
#include <dev/ic/dc21040reg.h>
#define DEVAR_INCLUDE "dev/pci/if_devar.h"
#endif /* __NetBSD__ */
/*
* Intel CPUs should use I/O mapped access.
*/
#if defined(__i386__) || defined(TULIP_EISA)
#define TULIP_IOMAPPED
#endif
#if 0
/*
* This turns on all sort of debugging stuff and make the
* driver much larger.
*/
#define TULIP_DEBUG
#endif
#if 0
#define TULIP_PERFSTATS
#endif
#if 0
#define TULIP_USE_SOFTINTR
#endif
#define TULIP_HZ 10
#include DEVAR_INCLUDE
/*
* This module supports
* the DEC 21040 PCI Ethernet Controller.
* the DEC 21041 PCI Ethernet Controller.
* the DEC 21140 PCI Fast Ethernet Controller.
*/
static void tulip_mii_autonegotiate(tulip_softc_t * const sc, const unsigned phyaddr);
static tulip_intrfunc_t tulip_intr_shared(void *arg);
static tulip_intrfunc_t tulip_intr_normal(void *arg);
static void tulip_init(tulip_softc_t * const sc);
static void tulip_reset(tulip_softc_t * const sc);
static ifnet_ret_t tulip_ifstart_one(struct ifnet *ifp);
static ifnet_ret_t tulip_ifstart(struct ifnet *ifp);
static struct mbuf *tulip_txput(tulip_softc_t * const sc, struct mbuf *m);
static void tulip_txput_setup(tulip_softc_t * const sc);
static void tulip_rx_intr(tulip_softc_t * const sc);
static void tulip_addr_filter(tulip_softc_t * const sc);
static unsigned tulip_mii_readreg(tulip_softc_t * const sc, unsigned devaddr, unsigned regno);
static void tulip_mii_writereg(tulip_softc_t * const sc, unsigned devaddr, unsigned regno, unsigned data);
static int tulip_mii_map_abilities(tulip_softc_t * const sc, unsigned abilities);
static tulip_media_t tulip_mii_phy_readspecific(tulip_softc_t * const sc);
static int tulip_srom_decode(tulip_softc_t * const sc);
#if defined(IFM_ETHER)
static int tulip_ifmedia_change(struct ifnet * const ifp);
static void tulip_ifmedia_status(struct ifnet * const ifp, struct ifmediareq *req);
#endif
/* static void tulip_21140_map_media(tulip_softc_t *sc); */
static void
tulip_timeout_callback(
void *arg)
{
tulip_softc_t * const sc = arg;
tulip_spl_t s = TULIP_RAISESPL();
TULIP_PERFSTART(timeout)
sc->tulip_flags &= ~TULIP_TIMEOUTPENDING;
sc->tulip_probe_timeout -= 1000 / TULIP_HZ;
(sc->tulip_boardsw->bd_media_poll)(sc, TULIP_MEDIAPOLL_TIMER);
TULIP_PERFEND(timeout);
TULIP_RESTORESPL(s);
}
static void
tulip_timeout(
tulip_softc_t * const sc)
{
if (sc->tulip_flags & TULIP_TIMEOUTPENDING)
return;
sc->tulip_flags |= TULIP_TIMEOUTPENDING;
timeout(tulip_timeout_callback, sc, (hz + TULIP_HZ / 2) / TULIP_HZ);
}
#if defined(TULIP_NEED_FASTTIMEOUT)
static void
tulip_fasttimeout_callback(
void *arg)
{
tulip_softc_t * const sc = arg;
tulip_spl_t s = TULIP_RAISESPL();
sc->tulip_flags &= ~TULIP_FASTTIMEOUTPENDING;
(sc->tulip_boardsw->bd_media_poll)(sc, TULIP_MEDIAPOLL_FASTTIMER);
TULIP_RESTORESPL(s);
}
static void
tulip_fasttimeout(
tulip_softc_t * const sc)
{
if (sc->tulip_flags & TULIP_FASTTIMEOUTPENDING)
return;
sc->tulip_flags |= TULIP_FASTTIMEOUTPENDING;
timeout(tulip_fasttimeout_callback, sc, 1);
}
#endif
static int
tulip_txprobe(
tulip_softc_t * const sc)
{
struct mbuf *m;
/*
* Before we are sure this is the right media we need
* to send a small packet to make sure there's carrier.
* Strangely, BNC and AUI will "see" receive data if
* either is connected so the transmit is the only way
* to verify the connectivity.
*/
MGETHDR(m, M_DONTWAIT, MT_DATA);
if (m == NULL)
return 0;
/*
* Construct a LLC TEST message which will point to ourselves.
*/
bcopy(sc->tulip_enaddr, mtod(m, struct ether_header *)->ether_dhost, 6);
bcopy(sc->tulip_enaddr, mtod(m, struct ether_header *)->ether_shost, 6);
mtod(m, struct ether_header *)->ether_type = htons(3);
mtod(m, unsigned char *)[14] = 0;
mtod(m, unsigned char *)[15] = 0;
mtod(m, unsigned char *)[16] = 0xE3; /* LLC Class1 TEST (no poll) */
m->m_len = m->m_pkthdr.len = sizeof(struct ether_header) + 3;
/*
* send it!
*/
sc->tulip_cmdmode |= TULIP_CMD_TXRUN;
sc->tulip_intrmask |= TULIP_STS_TXINTR;
sc->tulip_flags |= TULIP_TXPROBE_ACTIVE;
TULIP_CSR_WRITE(sc, csr_command, sc->tulip_cmdmode);
TULIP_CSR_WRITE(sc, csr_intr, sc->tulip_intrmask);
if ((m = tulip_txput(sc, m)) != NULL)
m_freem(m);
sc->tulip_probe.probe_txprobes++;
return 1;
}
#ifdef BIG_PACKET
#define TULIP_SIAGEN_WATCHDOG (sc->tulip_if.if_mtu > ETHERMTU ? TULIP_WATCHDOG_RXDISABLE|TULIP_WATCHDOG_TXDISABLE : 0)
#else
#define TULIP_SIAGEN_WATCHDOG 0
#endif
static void
tulip_media_set(
tulip_softc_t * const sc,
tulip_media_t media)
{
const tulip_media_info_t *mi = sc->tulip_mediums[media];
if (mi == NULL)
return;
/*
* If we are switching media, make sure we don't think there's
* any stale RX activity
*/
sc->tulip_flags &= ~TULIP_RXACT;
if (mi->mi_type == TULIP_MEDIAINFO_SIA) {
TULIP_CSR_WRITE(sc, csr_sia_connectivity, TULIP_SIACONN_RESET);
TULIP_CSR_WRITE(sc, csr_sia_tx_rx, mi->mi_sia_tx_rx);
if (sc->tulip_features & TULIP_HAVE_SIAGP) {
TULIP_CSR_WRITE(sc, csr_sia_general, mi->mi_sia_gp_control|mi->mi_sia_general|TULIP_SIAGEN_WATCHDOG);
TULIP_CSR_WRITE(sc, csr_sia_general, mi->mi_sia_gp_data|mi->mi_sia_general|TULIP_SIAGEN_WATCHDOG);
} else {
TULIP_CSR_WRITE(sc, csr_sia_general, mi->mi_sia_general|TULIP_SIAGEN_WATCHDOG);
}
TULIP_CSR_WRITE(sc, csr_sia_connectivity, mi->mi_sia_connectivity);
} else if (mi->mi_type == TULIP_MEDIAINFO_GPR) {
#define TULIP_GPR_CMDBITS (TULIP_CMD_PORTSELECT|TULIP_CMD_PCSFUNCTION|TULIP_CMD_SCRAMBLER|TULIP_CMD_TXTHRSHLDCTL)
/*
* If the cmdmode bits don't match the currently operating mode,
* set the cmdmode appropriately and reset the chip.
*/
if (((mi->mi_cmdmode ^ TULIP_CSR_READ(sc, csr_command)) & TULIP_GPR_CMDBITS) != 0) {
sc->tulip_cmdmode &= ~TULIP_GPR_CMDBITS;
sc->tulip_cmdmode |= mi->mi_cmdmode;
tulip_reset(sc);
}
TULIP_CSR_WRITE(sc, csr_gp, TULIP_GP_PINSET|sc->tulip_gpinit);
DELAY(10);
TULIP_CSR_WRITE(sc, csr_gp, (u_int8_t) mi->mi_gpdata);
} else if (mi->mi_type == TULIP_MEDIAINFO_SYM) {
/*
* If the cmdmode bits don't match the currently operating mode,
* set the cmdmode appropriately and reset the chip.
*/
if (((mi->mi_cmdmode ^ TULIP_CSR_READ(sc, csr_command)) & TULIP_GPR_CMDBITS) != 0) {
sc->tulip_cmdmode &= ~TULIP_GPR_CMDBITS;
sc->tulip_cmdmode |= mi->mi_cmdmode;
tulip_reset(sc);
}
TULIP_CSR_WRITE(sc, csr_sia_general, mi->mi_gpcontrol);
TULIP_CSR_WRITE(sc, csr_sia_general, mi->mi_gpdata);
} else if (mi->mi_type == TULIP_MEDIAINFO_MII
&& sc->tulip_probe_state != TULIP_PROBE_INACTIVE) {
int idx;
if (sc->tulip_features & TULIP_HAVE_SIAGP) {
const u_int8_t *dp;
dp = &sc->tulip_rombuf[mi->mi_reset_offset];
for (idx = 0; idx < mi->mi_reset_length; idx++, dp += 2) {
DELAY(10);
TULIP_CSR_WRITE(sc, csr_sia_general, (dp[0] + 256 * dp[1]) << 16);
}
sc->tulip_phyaddr = mi->mi_phyaddr;
dp = &sc->tulip_rombuf[mi->mi_gpr_offset];
for (idx = 0; idx < mi->mi_gpr_length; idx++, dp += 2) {
DELAY(10);
TULIP_CSR_WRITE(sc, csr_sia_general, (dp[0] + 256 * dp[1]) << 16);
}
} else {
for (idx = 0; idx < mi->mi_reset_length; idx++) {
DELAY(10);
TULIP_CSR_WRITE(sc, csr_gp, sc->tulip_rombuf[mi->mi_reset_offset + idx]);
}
sc->tulip_phyaddr = mi->mi_phyaddr;
for (idx = 0; idx < mi->mi_gpr_length; idx++) {
DELAY(10);
TULIP_CSR_WRITE(sc, csr_gp, sc->tulip_rombuf[mi->mi_gpr_offset + idx]);
}
}
if (sc->tulip_flags & TULIP_TRYNWAY) {
tulip_mii_autonegotiate(sc, sc->tulip_phyaddr);
} else if ((sc->tulip_flags & TULIP_DIDNWAY) == 0) {
u_int32_t data = tulip_mii_readreg(sc, sc->tulip_phyaddr, PHYREG_CONTROL);
data &= ~(PHYCTL_SELECT_100MB|PHYCTL_FULL_DUPLEX|PHYCTL_AUTONEG_ENABLE);
sc->tulip_flags &= ~TULIP_DIDNWAY;
if (TULIP_IS_MEDIA_FD(media))
data |= PHYCTL_FULL_DUPLEX;
if (TULIP_IS_MEDIA_100MB(media))
data |= PHYCTL_SELECT_100MB;
tulip_mii_writereg(sc, sc->tulip_phyaddr, PHYREG_CONTROL, data);
}
}
}
static void
tulip_linkup(
tulip_softc_t * const sc,
tulip_media_t media)
{
if ((sc->tulip_flags & TULIP_LINKUP) == 0)
sc->tulip_flags |= TULIP_PRINTLINKUP;
sc->tulip_flags |= TULIP_LINKUP;
sc->tulip_if.if_flags &= ~IFF_OACTIVE;
#if 0 /* XXX how does with work with ifmedia? */
if ((sc->tulip_flags & TULIP_DIDNWAY) == 0) {
if (sc->tulip_if.if_flags & IFF_FULLDUPLEX) {
if (TULIP_CAN_MEDIA_FD(media)
&& sc->tulip_mediums[TULIP_FD_MEDIA_OF(media)] != NULL)
media = TULIP_FD_MEDIA_OF(media);
} else {
if (TULIP_IS_MEDIA_FD(media)
&& sc->tulip_mediums[TULIP_HD_MEDIA_OF(media)] != NULL)
media = TULIP_HD_MEDIA_OF(media);
}
}
#endif
if (sc->tulip_media != media) {
#ifdef TULIP_DEBUG
sc->tulip_dbg.dbg_last_media = sc->tulip_media;
#endif
sc->tulip_media = media;
sc->tulip_flags |= TULIP_PRINTMEDIA;
if (TULIP_IS_MEDIA_FD(sc->tulip_media)) {
sc->tulip_cmdmode |= TULIP_CMD_FULLDUPLEX;
} else if (sc->tulip_chipid != TULIP_21041 || (sc->tulip_flags & TULIP_DIDNWAY) == 0) {
sc->tulip_cmdmode &= ~TULIP_CMD_FULLDUPLEX;
}
}
/*
* We could set probe_timeout to 0 but setting to 3000 puts this
* in one central place and the only matters is tulip_link is
* followed by a tulip_timeout. Therefore setting it should not
* result in aberrant behavour.
*/
sc->tulip_probe_timeout = 3000;
sc->tulip_probe_state = TULIP_PROBE_INACTIVE;
sc->tulip_flags &= ~(TULIP_TXPROBE_ACTIVE|TULIP_TRYNWAY);
if (sc->tulip_flags & TULIP_INRESET) {
tulip_media_set(sc, sc->tulip_media);
} else {
tulip_reset(sc);
tulip_init(sc);
}
}
static void
tulip_media_print(
tulip_softc_t * const sc)
{
if ((sc->tulip_flags & TULIP_LINKUP) == 0)
return;
if (sc->tulip_flags & TULIP_PRINTMEDIA) {
printf(TULIP_PRINTF_FMT ": enabling %s port\n",
TULIP_PRINTF_ARGS,
tulip_mediums[sc->tulip_media]);
sc->tulip_flags &= ~(TULIP_PRINTMEDIA|TULIP_PRINTLINKUP);
} else if (sc->tulip_flags & TULIP_PRINTLINKUP) {
printf(TULIP_PRINTF_FMT ": link up\n", TULIP_PRINTF_ARGS);
sc->tulip_flags &= ~TULIP_PRINTLINKUP;
}
}
#if defined(TULIP_DO_GPR_SENSE)
static tulip_media_t
tulip_21140_gpr_media_sense(
tulip_softc_t * const sc)
{
tulip_media_t maybe_media = TULIP_MEDIA_UNKNOWN;
tulip_media_t last_media = TULIP_MEDIA_UNKNOWN;
tulip_media_t media;
/*
* If one of the media blocks contained a default media flag,
* use that.
*/
for (media = TULIP_MEDIA_UNKNOWN; media < TULIP_MEDIA_MAX; media++) {
const tulip_media_info_t *mi;
/*
* Media is not supported (or is full-duplex).
*/
if ((mi = sc->tulip_mediums[media]) == NULL || TULIP_IS_MEDIA_FD(media))
continue;
if (mi->mi_type != TULIP_MEDIAINFO_GPR)
continue;
/*
* Remember the media is this is the "default" media.
*/
if (mi->mi_default && maybe_media == TULIP_MEDIA_UNKNOWN)
maybe_media = media;
/*
* No activity mask? Can't see if it is active if there's no mask.
*/
if (mi->mi_actmask == 0)
continue;
/*
* Does the activity data match?
*/
if ((TULIP_CSR_READ(sc, csr_gp) & mi->mi_actmask) != mi->mi_actdata)
continue;
#if defined(TULIP_DEBUG)
printf(TULIP_PRINTF_FMT ": gpr_media_sense: %s: 0x%02x & 0x%02x == 0x%02x\n",
TULIP_PRINTF_ARGS, tulip_mediums[media],
TULIP_CSR_READ(sc, csr_gp) & 0xFF,
mi->mi_actmask, mi->mi_actdata);
#endif
/*
* It does! If this is the first media we detected, then
* remember this media. If isn't the first, then there were
* multiple matches which we equate to no match (since we don't
* which to select (if any).
*/
if (last_media == TULIP_MEDIA_UNKNOWN) {
last_media = media;
} else if (last_media != media) {
last_media = TULIP_MEDIA_UNKNOWN;
}
}
return (last_media != TULIP_MEDIA_UNKNOWN) ? last_media : maybe_media;
}
#endif /* TULIP_DO_GPR_SENSE */
static tulip_link_status_t
tulip_media_link_monitor(
tulip_softc_t * const sc)
{
const tulip_media_info_t * const mi = sc->tulip_mediums[sc->tulip_media];
tulip_link_status_t linkup = TULIP_LINK_DOWN;
if (mi == NULL) {
#if defined(DIAGNOSTIC) || defined(TULIP_DEBUG)
panic("tulip_media_link_monitor: %s: botch at line %d\n",
tulip_mediums[sc->tulip_media],__LINE__);
#endif
return TULIP_LINK_UNKNOWN;
}
/*
* Have we seen some packets? If so, the link must be good.
*/
if ((sc->tulip_flags & (TULIP_RXACT|TULIP_LINKUP)) == (TULIP_RXACT|TULIP_LINKUP)) {
sc->tulip_flags &= ~TULIP_RXACT;
sc->tulip_probe_timeout = 3000;
return TULIP_LINK_UP;
}
sc->tulip_flags &= ~TULIP_RXACT;
if (mi->mi_type == TULIP_MEDIAINFO_MII) {
u_int32_t status;
/*
* Read the PHY status register.
*/
status = tulip_mii_readreg(sc, sc->tulip_phyaddr, PHYREG_STATUS);
if (status & PHYSTS_AUTONEG_DONE) {
/*
* If the PHY has completed autonegotiation, see the if the
* remote systems abilities have changed. If so, upgrade or
* downgrade as appropriate.
*/
u_int32_t abilities = tulip_mii_readreg(sc, sc->tulip_phyaddr, PHYREG_AUTONEG_ABILITIES);
abilities = (abilities << 6) & status;
if (abilities != sc->tulip_abilities) {
#if defined(TULIP_DEBUG)
loudprintf(TULIP_PRINTF_FMT "(phy%d): autonegotiation changed: 0x%04x -> 0x%04x\n",
TULIP_PRINTF_ARGS, sc->tulip_phyaddr,
sc->tulip_abilities, abilities);
#endif
if (tulip_mii_map_abilities(sc, abilities)) {
tulip_linkup(sc, sc->tulip_probe_media);
return TULIP_LINK_UP;
}
/*
* if we had selected media because of autonegotiation,
* we need to probe for the new media.
*/
sc->tulip_probe_state = TULIP_PROBE_INACTIVE;
if (sc->tulip_flags & TULIP_DIDNWAY)
return TULIP_LINK_DOWN;
}
}
/*
* The link is now up. If was down, say its back up.
*/
if ((status & (PHYSTS_LINK_UP|PHYSTS_REMOTE_FAULT)) == PHYSTS_LINK_UP)
linkup = TULIP_LINK_UP;
} else if (mi->mi_type == TULIP_MEDIAINFO_GPR) {
/*
* No activity sensor? Assume all's well.
*/
if (mi->mi_actmask == 0)
return TULIP_LINK_UNKNOWN;
/*
* Does the activity data match?
*/
if ((TULIP_CSR_READ(sc, csr_gp) & mi->mi_actmask) == mi->mi_actdata)
linkup = TULIP_LINK_UP;
} else if (mi->mi_type == TULIP_MEDIAINFO_SIA) {
/*
* Assume non TP ok for now.
*/
if (!TULIP_IS_MEDIA_TP(sc->tulip_media))
return TULIP_LINK_UNKNOWN;
if ((TULIP_CSR_READ(sc, csr_sia_status) & TULIP_SIASTS_LINKFAIL) == 0)
linkup = TULIP_LINK_UP;
} else if (mi->mi_type == TULIP_MEDIAINFO_SYM) {
return TULIP_LINK_UNKNOWN;
}
/*
* We will wait for 3 seconds until the link goes into suspect mode.
*/
if (sc->tulip_flags & TULIP_LINKUP) {
if (linkup == TULIP_LINK_UP)
sc->tulip_probe_timeout = 3000;
if (sc->tulip_probe_timeout > 0)
return TULIP_LINK_UP;
sc->tulip_flags &= ~TULIP_LINKUP;
printf(TULIP_PRINTF_FMT ": link down: cable problem?\n", TULIP_PRINTF_ARGS);
}
#if defined(TULIP_DEBUG)
sc->tulip_dbg.dbg_link_downed++;
#endif
return TULIP_LINK_DOWN;
}
static void
tulip_media_poll(
tulip_softc_t * const sc,
tulip_mediapoll_event_t event)
{
#if defined(TULIP_DEBUG)
sc->tulip_dbg.dbg_events[event]++;
#endif
if (sc->tulip_probe_state == TULIP_PROBE_INACTIVE
&& event == TULIP_MEDIAPOLL_TIMER) {
switch (tulip_media_link_monitor(sc)) {
case TULIP_LINK_DOWN: {
/*
* Link Monitor failed. Probe for new media.
*/
event = TULIP_MEDIAPOLL_LINKFAIL;
break;
}
case TULIP_LINK_UP: {
/*
* Check again soon.
*/
tulip_timeout(sc);
return;
}
case TULIP_LINK_UNKNOWN: {
/*
* We can't tell so don't bother.
*/
return;
}
}
}
if (event == TULIP_MEDIAPOLL_LINKFAIL) {
if (sc->tulip_probe_state == TULIP_PROBE_INACTIVE) {
if (TULIP_DO_AUTOSENSE(sc)) {
#if defined(TULIP_DEBUG)
sc->tulip_dbg.dbg_link_failures++;
#endif
sc->tulip_media = TULIP_MEDIA_UNKNOWN;
tulip_reset(sc); /* restart probe */
}
return;
}
#if defined(TULIP_DEBUG)
sc->tulip_dbg.dbg_link_pollintrs++;
#endif
}
if (event == TULIP_MEDIAPOLL_START) {
sc->tulip_if.if_flags |= IFF_OACTIVE;
if (sc->tulip_probe_state != TULIP_PROBE_INACTIVE)
return;
sc->tulip_probe_mediamask = 0;
sc->tulip_probe_passes = 0;
#if defined(TULIP_DEBUG)
sc->tulip_dbg.dbg_media_probes++;
#endif
/*
* If the SROM contained an explicit media to use, use it.
*/
sc->tulip_cmdmode &= ~(TULIP_CMD_RXRUN|TULIP_CMD_FULLDUPLEX);
sc->tulip_flags |= TULIP_TRYNWAY|TULIP_PROBE1STPASS;
sc->tulip_flags &= ~(TULIP_DIDNWAY|TULIP_PRINTMEDIA|TULIP_PRINTLINKUP);
/*
* connidx is defaulted to a media_unknown type.
*/
sc->tulip_probe_media = tulip_srom_conninfo[sc->tulip_connidx].sc_media;
if (sc->tulip_probe_media != TULIP_MEDIA_UNKNOWN) {
tulip_linkup(sc, sc->tulip_probe_media);
tulip_timeout(sc);
return;
}
if (sc->tulip_features & TULIP_HAVE_GPR) {
sc->tulip_probe_state = TULIP_PROBE_GPRTEST;
sc->tulip_probe_timeout = 2000;
} else {
sc->tulip_probe_media = TULIP_MEDIA_MAX;
sc->tulip_probe_timeout = 0;
sc->tulip_probe_state = TULIP_PROBE_MEDIATEST;
}
}
/*
* Ignore txprobe failures or spurious callbacks.
*/
if (event == TULIP_MEDIAPOLL_TXPROBE_FAILED
&& sc->tulip_probe_state != TULIP_PROBE_MEDIATEST) {
sc->tulip_flags &= ~TULIP_TXPROBE_ACTIVE;
return;
}
/*
* If we really transmitted a packet, then that's the media we'll use.
*/
if (event == TULIP_MEDIAPOLL_TXPROBE_OK || event == TULIP_MEDIAPOLL_LINKPASS) {
if (event == TULIP_MEDIAPOLL_LINKPASS)
sc->tulip_probe_media = TULIP_MEDIA_10BASET;
#if defined(TULIP_DEBUG)
else
sc->tulip_dbg.dbg_txprobes_ok[sc->tulip_probe_media]++;
#endif
tulip_linkup(sc, sc->tulip_probe_media);
tulip_timeout(sc);
return;
}
if (sc->tulip_probe_state == TULIP_PROBE_GPRTEST) {
#if defined(TULIP_DO_GPR_SENSE)
/*
* Check for media via the general purpose register.
*
* Try to sense the media via the GPR. If the same value
* occurs 3 times in a row then just use that.
*/
if (sc->tulip_probe_timeout > 0) {
tulip_media_t new_probe_media = tulip_21140_gpr_media_sense(sc);
#if defined(TULIP_DEBUG)
printf(TULIP_PRINTF_FMT ": media_poll: gpr sensing = %s\n",
TULIP_PRINTF_ARGS, tulip_mediums[new_probe_media]);
#endif
if (new_probe_media != TULIP_MEDIA_UNKNOWN) {
if (new_probe_media == sc->tulip_probe_media) {
if (--sc->tulip_probe_count == 0)
tulip_linkup(sc, sc->tulip_probe_media);
} else {
sc->tulip_probe_count = 10;
}
}
sc->tulip_probe_media = new_probe_media;
tulip_timeout(sc);
return;
}
#endif /* TULIP_DO_GPR_SENSE */
/*
* Brute force. We cycle through each of the media types
* and try to transmit a packet.
*/
sc->tulip_probe_state = TULIP_PROBE_MEDIATEST;
sc->tulip_probe_media = TULIP_MEDIA_MAX;
sc->tulip_probe_timeout = 0;
tulip_timeout(sc);
return;
}
if (sc->tulip_probe_state != TULIP_PROBE_MEDIATEST
&& (sc->tulip_features & TULIP_HAVE_MII)) {
tulip_media_t old_media = sc->tulip_probe_media;
tulip_mii_autonegotiate(sc, sc->tulip_phyaddr);
switch (sc->tulip_probe_state) {
case TULIP_PROBE_FAILED:
case TULIP_PROBE_MEDIATEST: {
/*
* Try the next media.
*/
sc->tulip_probe_mediamask |= sc->tulip_mediums[sc->tulip_probe_media]->mi_mediamask;
sc->tulip_probe_timeout = 0;
#ifdef notyet
if (sc->tulip_probe_state == TULIP_PROBE_FAILED)
break;
if (sc->tulip_probe_media != tulip_mii_phy_readspecific(sc))
break;
sc->tulip_probe_timeout = TULIP_IS_MEDIA_TP(sc->tulip_probe_media) ? 2500 : 300;
#endif
break;
}
case TULIP_PROBE_PHYAUTONEG: {
return;
}
case TULIP_PROBE_INACTIVE: {
/*
* Only probe if we autonegotiated a media that hasn't failed.
*/
sc->tulip_probe_timeout = 0;
if (sc->tulip_probe_mediamask & TULIP_BIT(sc->tulip_probe_media)) {
sc->tulip_probe_media = old_media;
break;
}
tulip_linkup(sc, sc->tulip_probe_media);
tulip_timeout(sc);
return;
}
default: {
#if defined(DIAGNOSTIC) || defined(TULIP_DEBUG)
panic("tulip_media_poll: botch at line %d\n", __LINE__);
#endif
break;
}
}
}
if (event == TULIP_MEDIAPOLL_TXPROBE_FAILED) {
#if defined(TULIP_DEBUG)
sc->tulip_dbg.dbg_txprobes_failed[sc->tulip_probe_media]++;
#endif
sc->tulip_flags &= ~TULIP_TXPROBE_ACTIVE;
return;
}
/*
* switch to another media if we tried this one enough.
*/
if (/* event == TULIP_MEDIAPOLL_TXPROBE_FAILED || */ sc->tulip_probe_timeout <= 0) {
#if defined(TULIP_DEBUG)
if (sc->tulip_probe_media == TULIP_MEDIA_UNKNOWN) {
printf(TULIP_PRINTF_FMT ": poll media unknown!\n",
TULIP_PRINTF_ARGS);
sc->tulip_probe_media = TULIP_MEDIA_MAX;
}
#endif
/*
* Find the next media type to check for. Full Duplex
* types are not allowed.
*/
do {
sc->tulip_probe_media -= 1;
if (sc->tulip_probe_media == TULIP_MEDIA_UNKNOWN) {
if (++sc->tulip_probe_passes == 3) {
printf(TULIP_PRINTF_FMT ": autosense failed: cable problem?\n",
TULIP_PRINTF_ARGS);
if ((sc->tulip_if.if_flags & IFF_UP) == 0) {
sc->tulip_if.if_flags &= ~IFF_RUNNING;
sc->tulip_probe_state = TULIP_PROBE_INACTIVE;
return;
}
}
sc->tulip_flags ^= TULIP_TRYNWAY; /* XXX */
sc->tulip_probe_mediamask = 0;
sc->tulip_probe_media = TULIP_MEDIA_MAX - 1;
}
} while (sc->tulip_mediums[sc->tulip_probe_media] == NULL
|| (sc->tulip_probe_mediamask & TULIP_BIT(sc->tulip_probe_media))
|| TULIP_IS_MEDIA_FD(sc->tulip_probe_media));
#if defined(TULIP_DEBUG)
printf(TULIP_PRINTF_FMT ": %s: probing %s\n", TULIP_PRINTF_ARGS,
event == TULIP_MEDIAPOLL_TXPROBE_FAILED ? "txprobe failed" : "timeout",
tulip_mediums[sc->tulip_probe_media]);
#endif
sc->tulip_probe_timeout = TULIP_IS_MEDIA_TP(sc->tulip_probe_media) ? 2500 : 1000;
sc->tulip_probe_state = TULIP_PROBE_MEDIATEST;
sc->tulip_probe.probe_txprobes = 0;
tulip_reset(sc);
tulip_media_set(sc, sc->tulip_probe_media);
sc->tulip_flags &= ~TULIP_TXPROBE_ACTIVE;
}
tulip_timeout(sc);
/*
* If this is hanging off a phy, we know are doing NWAY and we have
* forced the phy to a specific speed. Wait for link up before
* before sending a packet.
*/
switch (sc->tulip_mediums[sc->tulip_probe_media]->mi_type) {
case TULIP_MEDIAINFO_MII: {
if (sc->tulip_probe_media != tulip_mii_phy_readspecific(sc))
return;
break;
}
case TULIP_MEDIAINFO_SIA: {
if (TULIP_IS_MEDIA_TP(sc->tulip_probe_media)) {
if (TULIP_CSR_READ(sc, csr_sia_status) & TULIP_SIASTS_LINKFAIL)
return;
tulip_linkup(sc, sc->tulip_probe_media);
#ifdef notyet
if (sc->tulip_features & TULIP_HAVE_MII)
tulip_timeout(sc);
#endif
return;
}
break;
}
case TULIP_MEDIAINFO_RESET:
case TULIP_MEDIAINFO_SYM:
case TULIP_MEDIAINFO_GPR: {
break;
}
}
/*
* Try to send a packet.
*/
tulip_txprobe(sc);
}
static void
tulip_media_select(
tulip_softc_t * const sc)
{
if (sc->tulip_features & TULIP_HAVE_GPR) {
TULIP_CSR_WRITE(sc, csr_gp, TULIP_GP_PINSET|sc->tulip_gpinit);
DELAY(10);
TULIP_CSR_WRITE(sc, csr_gp, sc->tulip_gpdata);
}
/*
* If this board has no media, just return
*/
if (sc->tulip_features & TULIP_HAVE_NOMEDIA)
return;
if (sc->tulip_media == TULIP_MEDIA_UNKNOWN) {
TULIP_CSR_WRITE(sc, csr_intr, sc->tulip_intrmask);
(*sc->tulip_boardsw->bd_media_poll)(sc, TULIP_MEDIAPOLL_START);
} else {
tulip_media_set(sc, sc->tulip_media);
}
}
static void
tulip_21040_mediainfo_init(
tulip_softc_t * const sc,
tulip_media_t media)
{
sc->tulip_cmdmode |= TULIP_CMD_CAPTREFFCT|TULIP_CMD_THRSHLD160
|TULIP_CMD_BACKOFFCTR;
sc->tulip_if.if_baudrate = 10000000;
if (media == TULIP_MEDIA_10BASET || media == TULIP_MEDIA_UNKNOWN) {
TULIP_MEDIAINFO_SIA_INIT(sc, &sc->tulip_mediainfo[0], 21040, 10BASET);
TULIP_MEDIAINFO_SIA_INIT(sc, &sc->tulip_mediainfo[1], 21040, 10BASET_FD);
}
if (media == TULIP_MEDIA_AUIBNC || media == TULIP_MEDIA_UNKNOWN) {
TULIP_MEDIAINFO_SIA_INIT(sc, &sc->tulip_mediainfo[2], 21040, AUIBNC);
}
if (media == TULIP_MEDIA_UNKNOWN) {
TULIP_MEDIAINFO_SIA_INIT(sc, &sc->tulip_mediainfo[3], 21040, EXTSIA);
}
}
static void
tulip_21040_media_probe(
tulip_softc_t * const sc)
{
tulip_21040_mediainfo_init(sc, TULIP_MEDIA_UNKNOWN);
return;
}
static void
tulip_21040_10baset_only_media_probe(
tulip_softc_t * const sc)
{
tulip_21040_mediainfo_init(sc, TULIP_MEDIA_10BASET);
tulip_media_set(sc, TULIP_MEDIA_10BASET);
sc->tulip_media = TULIP_MEDIA_10BASET;
}
static void
tulip_21040_10baset_only_media_select(
tulip_softc_t * const sc)
{
sc->tulip_flags |= TULIP_LINKUP;
if (sc->tulip_media == TULIP_MEDIA_10BASET_FD) {
sc->tulip_cmdmode |= TULIP_CMD_FULLDUPLEX;
sc->tulip_flags &= ~TULIP_SQETEST;
} else {
sc->tulip_cmdmode &= ~TULIP_CMD_FULLDUPLEX;
sc->tulip_flags |= TULIP_SQETEST;
}
tulip_media_set(sc, sc->tulip_media);
}
static void
tulip_21040_auibnc_only_media_probe(
tulip_softc_t * const sc)
{
tulip_21040_mediainfo_init(sc, TULIP_MEDIA_AUIBNC);
sc->tulip_flags |= TULIP_SQETEST|TULIP_LINKUP;
tulip_media_set(sc, TULIP_MEDIA_AUIBNC);
sc->tulip_media = TULIP_MEDIA_AUIBNC;
}
static void
tulip_21040_auibnc_only_media_select(
tulip_softc_t * const sc)
{
tulip_media_set(sc, TULIP_MEDIA_AUIBNC);
sc->tulip_cmdmode &= ~TULIP_CMD_FULLDUPLEX;
}
static const tulip_boardsw_t tulip_21040_boardsw = {
TULIP_21040_GENERIC,
tulip_21040_media_probe,
tulip_media_select,
tulip_media_poll,
};
static const tulip_boardsw_t tulip_21040_10baset_only_boardsw = {
TULIP_21040_GENERIC,
tulip_21040_10baset_only_media_probe,
tulip_21040_10baset_only_media_select,
NULL,
};
static const tulip_boardsw_t tulip_21040_auibnc_only_boardsw = {
TULIP_21040_GENERIC,
tulip_21040_auibnc_only_media_probe,
tulip_21040_auibnc_only_media_select,
NULL,
};
static void
tulip_21041_mediainfo_init(
tulip_softc_t * const sc)
{
tulip_media_info_t * const mi = sc->tulip_mediainfo;
#ifdef notyet
if (sc->tulip_revinfo >= 0x20) {
TULIP_MEDIAINFO_SIA_INIT(sc, &mi[0], 21041P2, 10BASET);
TULIP_MEDIAINFO_SIA_INIT(sc, &mi[1], 21041P2, 10BASET_FD);
TULIP_MEDIAINFO_SIA_INIT(sc, &mi[0], 21041P2, AUI);
TULIP_MEDIAINFO_SIA_INIT(sc, &mi[1], 21041P2, BNC);
return;
}
#endif
TULIP_MEDIAINFO_SIA_INIT(sc, &mi[0], 21041, 10BASET);
TULIP_MEDIAINFO_SIA_INIT(sc, &mi[1], 21041, 10BASET_FD);
TULIP_MEDIAINFO_SIA_INIT(sc, &mi[2], 21041, AUI);
TULIP_MEDIAINFO_SIA_INIT(sc, &mi[3], 21041, BNC);
}
static void
tulip_21041_media_probe(
tulip_softc_t * const sc)
{
sc->tulip_if.if_baudrate = 10000000;
sc->tulip_cmdmode |= TULIP_CMD_CAPTREFFCT|TULIP_CMD_ENHCAPTEFFCT
|TULIP_CMD_THRSHLD160|TULIP_CMD_BACKOFFCTR;
sc->tulip_intrmask |= TULIP_STS_LINKPASS;
tulip_21041_mediainfo_init(sc);
}
static void
tulip_21041_media_poll(
tulip_softc_t * const sc,
const tulip_mediapoll_event_t event)
{
u_int32_t sia_status;
#if defined(TULIP_DEBUG)
sc->tulip_dbg.dbg_events[event]++;
#endif
if (event == TULIP_MEDIAPOLL_LINKFAIL) {
if (sc->tulip_probe_state != TULIP_PROBE_INACTIVE
|| !TULIP_DO_AUTOSENSE(sc))
return;
sc->tulip_media = TULIP_MEDIA_UNKNOWN;
tulip_reset(sc); /* start probe */
return;
}
/*
* If we've been been asked to start a poll or link change interrupt
* restart the probe (and reset the tulip to a known state).
*/
if (event == TULIP_MEDIAPOLL_START) {
sc->tulip_if.if_flags |= IFF_OACTIVE;
sc->tulip_cmdmode &= ~(TULIP_CMD_FULLDUPLEX|TULIP_CMD_RXRUN);
#ifdef notyet
if (sc->tulip_revinfo >= 0x20) {
sc->tulip_cmdmode |= TULIP_CMD_FULLDUPLEX;
sc->tulip_flags |= TULIP_DIDNWAY;
}
#endif
TULIP_CSR_WRITE(sc, csr_command, sc->tulip_cmdmode);
sc->tulip_probe_state = TULIP_PROBE_MEDIATEST;
sc->tulip_probe_media = TULIP_MEDIA_10BASET;
sc->tulip_probe_timeout = TULIP_21041_PROBE_10BASET_TIMEOUT;
tulip_media_set(sc, TULIP_MEDIA_10BASET);
tulip_timeout(sc);
return;
}
if (sc->tulip_probe_state == TULIP_PROBE_INACTIVE)
return;
if (event == TULIP_MEDIAPOLL_TXPROBE_OK) {
#if defined(TULIP_DEBUG)
sc->tulip_dbg.dbg_txprobes_ok[sc->tulip_probe_media]++;
#endif
tulip_linkup(sc, sc->tulip_probe_media);
return;
}
sia_status = TULIP_CSR_READ(sc, csr_sia_status);
TULIP_CSR_WRITE(sc, csr_sia_status, sia_status);
if ((sia_status & TULIP_SIASTS_LINKFAIL) == 0) {
if (sc->tulip_revinfo >= 0x20) {
if (sia_status & (PHYSTS_10BASET_FD << (16 - 6)))
sc->tulip_probe_media = TULIP_MEDIA_10BASET_FD;
}
/*
* If the link has passed LinkPass, 10baseT is the
* proper media to use.
*/
tulip_linkup(sc, sc->tulip_probe_media);
return;
}
/*
* wait for up to 2.4 seconds for the link to reach pass state.
* Only then start scanning the other media for activity.
* choose media with receive activity over those without.
*/
if (sc->tulip_probe_media == TULIP_MEDIA_10BASET) {
if (event != TULIP_MEDIAPOLL_TIMER)
return;
if (sc->tulip_probe_timeout > 0
&& (sia_status & TULIP_SIASTS_OTHERRXACTIVITY) == 0) {
tulip_timeout(sc);
return;
}
sc->tulip_probe_timeout = TULIP_21041_PROBE_AUIBNC_TIMEOUT;
sc->tulip_flags |= TULIP_WANTRXACT;
if (sia_status & TULIP_SIASTS_OTHERRXACTIVITY) {
sc->tulip_probe_media = TULIP_MEDIA_BNC;
} else {
sc->tulip_probe_media = TULIP_MEDIA_AUI;
}
tulip_media_set(sc, sc->tulip_probe_media);
tulip_timeout(sc);
return;
}
/*
* If we failed, clear the txprobe active flag.
*/
if (event == TULIP_MEDIAPOLL_TXPROBE_FAILED)
sc->tulip_flags &= ~TULIP_TXPROBE_ACTIVE;
if (event == TULIP_MEDIAPOLL_TIMER) {
/*
* If we've received something, then that's our link!
*/
if (sc->tulip_flags & TULIP_RXACT) {
tulip_linkup(sc, sc->tulip_probe_media);
return;
}
/*
* if no txprobe active
*/
if ((sc->tulip_flags & TULIP_TXPROBE_ACTIVE) == 0
&& ((sc->tulip_flags & TULIP_WANTRXACT) == 0
|| (sia_status & TULIP_SIASTS_RXACTIVITY))) {
sc->tulip_probe_timeout = TULIP_21041_PROBE_AUIBNC_TIMEOUT;
tulip_txprobe(sc);
tulip_timeout(sc);
return;
}
/*
* Take 2 passes through before deciding to not
* wait for receive activity. Then take another
* two passes before spitting out a warning.
*/
if (sc->tulip_probe_timeout <= 0) {
if (sc->tulip_flags & TULIP_WANTRXACT) {
sc->tulip_flags &= ~TULIP_WANTRXACT;
sc->tulip_probe_timeout = TULIP_21041_PROBE_AUIBNC_TIMEOUT;
} else {
printf(TULIP_PRINTF_FMT ": autosense failed: cable problem?\n",
TULIP_PRINTF_ARGS);
if ((sc->tulip_if.if_flags & IFF_UP) == 0) {
sc->tulip_if.if_flags &= ~IFF_RUNNING;
sc->tulip_probe_state = TULIP_PROBE_INACTIVE;
return;
}
}
}
}
/*
* Since this media failed to probe, try the other one.
*/
sc->tulip_probe_timeout = TULIP_21041_PROBE_AUIBNC_TIMEOUT;
if (sc->tulip_probe_media == TULIP_MEDIA_AUI) {
sc->tulip_probe_media = TULIP_MEDIA_BNC;
} else {
sc->tulip_probe_media = TULIP_MEDIA_AUI;
}
tulip_media_set(sc, sc->tulip_probe_media);
sc->tulip_flags &= ~TULIP_TXPROBE_ACTIVE;
tulip_timeout(sc);
}
static const tulip_boardsw_t tulip_21041_boardsw = {
TULIP_21041_GENERIC,
tulip_21041_media_probe,
tulip_media_select,
tulip_21041_media_poll
};
static const tulip_phy_attr_t tulip_mii_phy_attrlist[] = {
{ 0x20005c00, 0, /* 08-00-17 */
{
{ 0x19, 0x0040, 0x0040 }, /* 10TX */
{ 0x19, 0x0040, 0x0000 }, /* 100TX */
},
#if defined(TULIP_DEBUG)
"NS DP83840",
#endif
},
{ 0x0281F400, 0, /* 00-A0-7D */
{
{ 0x12, 0x0010, 0x0000 }, /* 10T */
{ }, /* 100TX */
{ 0x12, 0x0010, 0x0010 }, /* 100T4 */
{ 0x12, 0x0008, 0x0008 }, /* FULL_DUPLEX */
},
#if defined(TULIP_DEBUG)
"Seeq 80C240"
#endif
},
#if 0
{ 0x0015F420, 0, /* 00-A0-7D */
{
{ 0x12, 0x0010, 0x0000 }, /* 10T */
{ }, /* 100TX */
{ 0x12, 0x0010, 0x0010 }, /* 100T4 */
{ 0x12, 0x0008, 0x0008 }, /* FULL_DUPLEX */
},
#if defined(TULIP_DEBUG)
"Broadcom BCM5000"
#endif
},
#endif
{ 0x0281F400, 0, /* 00-A0-BE */
{
{ 0x11, 0x8000, 0x0000 }, /* 10T */
{ 0x11, 0x8000, 0x8000 }, /* 100TX */
{ }, /* 100T4 */
{ 0x11, 0x4000, 0x4000 }, /* FULL_DUPLEX */
},
#if defined(TULIP_DEBUG)
"ICS 1890"
#endif
},
{ 0 }
};
static tulip_media_t
tulip_mii_phy_readspecific(
tulip_softc_t * const sc)
{
const tulip_phy_attr_t *attr;
u_int16_t data;
u_int32_t id;
unsigned idx = 0;
static const tulip_media_t table[] = {
TULIP_MEDIA_UNKNOWN,
TULIP_MEDIA_10BASET,
TULIP_MEDIA_100BASETX,
TULIP_MEDIA_100BASET4,
TULIP_MEDIA_UNKNOWN,
TULIP_MEDIA_10BASET_FD,
TULIP_MEDIA_100BASETX_FD,
TULIP_MEDIA_UNKNOWN
};
/*
* Don't read phy specific registers if link is not up.
*/
data = tulip_mii_readreg(sc, sc->tulip_phyaddr, PHYREG_STATUS);
if ((data & (PHYSTS_LINK_UP|PHYSTS_EXTENDED_REGS)) != (PHYSTS_LINK_UP|PHYSTS_EXTENDED_REGS))
return TULIP_MEDIA_UNKNOWN;
id = (tulip_mii_readreg(sc, sc->tulip_phyaddr, PHYREG_IDLOW) << 16) |
tulip_mii_readreg(sc, sc->tulip_phyaddr, PHYREG_IDHIGH);
for (attr = tulip_mii_phy_attrlist;; attr++) {
if (attr->attr_id == 0)
return TULIP_MEDIA_UNKNOWN;
if ((id & ~0x0F) == attr->attr_id)
break;
}
if (attr->attr_modes[PHY_MODE_100TX].pm_regno) {
const tulip_phy_modedata_t * const pm = &attr->attr_modes[PHY_MODE_100TX];
data = tulip_mii_readreg(sc, sc->tulip_phyaddr, pm->pm_regno);
if ((data & pm->pm_mask) == pm->pm_value)
idx = 2;
}
if (idx == 0 && attr->attr_modes[PHY_MODE_100T4].pm_regno) {
const tulip_phy_modedata_t * const pm = &attr->attr_modes[PHY_MODE_100T4];
data = tulip_mii_readreg(sc, sc->tulip_phyaddr, pm->pm_regno);
if ((data & pm->pm_mask) == pm->pm_value)
idx = 3;
}
if (idx == 0 && attr->attr_modes[PHY_MODE_10T].pm_regno) {
const tulip_phy_modedata_t * const pm = &attr->attr_modes[PHY_MODE_10T];
data = tulip_mii_readreg(sc, sc->tulip_phyaddr, pm->pm_regno);
if ((data & pm->pm_mask) == pm->pm_value)
idx = 1;
}
if (idx != 0 && attr->attr_modes[PHY_MODE_FULLDUPLEX].pm_regno) {
const tulip_phy_modedata_t * const pm = &attr->attr_modes[PHY_MODE_FULLDUPLEX];
data = tulip_mii_readreg(sc, sc->tulip_phyaddr, pm->pm_regno);
idx += ((data & pm->pm_mask) == pm->pm_value ? 4 : 0);
}
return table[idx];
}
static unsigned
tulip_mii_get_phyaddr(
tulip_softc_t * const sc,
unsigned offset)
{
unsigned phyaddr;
for (phyaddr = 1; phyaddr < 32; phyaddr++) {
unsigned status = tulip_mii_readreg(sc, phyaddr, PHYREG_STATUS);
if (status == 0 || status == 0xFFFF || status < PHYSTS_10BASET)
continue;
if (offset == 0)
return phyaddr;
offset--;
}
if (offset == 0) {
unsigned status = tulip_mii_readreg(sc, 0, PHYREG_STATUS);
if (status == 0 || status == 0xFFFF || status < PHYSTS_10BASET)
return TULIP_MII_NOPHY;
return 0;
}
return TULIP_MII_NOPHY;
}
static int
tulip_mii_map_abilities(
tulip_softc_t * const sc,
unsigned abilities)
{
sc->tulip_abilities = abilities;
if (abilities & PHYSTS_100BASETX_FD) {
sc->tulip_probe_media = TULIP_MEDIA_100BASETX_FD;
} else if (abilities & PHYSTS_100BASET4) {
sc->tulip_probe_media = TULIP_MEDIA_100BASET4;
} else if (abilities & PHYSTS_100BASETX) {
sc->tulip_probe_media = TULIP_MEDIA_100BASETX;
} else if (abilities & PHYSTS_10BASET_FD) {
sc->tulip_probe_media = TULIP_MEDIA_10BASET_FD;
} else if (abilities & PHYSTS_10BASET) {
sc->tulip_probe_media = TULIP_MEDIA_10BASET;
} else {
sc->tulip_probe_state = TULIP_PROBE_MEDIATEST;
return 0;
}
sc->tulip_probe_state = TULIP_PROBE_INACTIVE;
return 1;
}
static void
tulip_mii_autonegotiate(
tulip_softc_t * const sc,
const unsigned phyaddr)
{
switch (sc->tulip_probe_state) {
case TULIP_PROBE_MEDIATEST:
case TULIP_PROBE_INACTIVE: {
sc->tulip_flags |= TULIP_DIDNWAY;
tulip_mii_writereg(sc, phyaddr, PHYREG_CONTROL, PHYCTL_RESET);
sc->tulip_probe_timeout = 3000;
sc->tulip_intrmask |= TULIP_STS_ABNRMLINTR|TULIP_STS_NORMALINTR;
sc->tulip_probe_state = TULIP_PROBE_PHYRESET;
/* FALL THROUGH */
}
case TULIP_PROBE_PHYRESET: {
u_int32_t status;
u_int32_t data = tulip_mii_readreg(sc, phyaddr, PHYREG_CONTROL);
if (data & PHYCTL_RESET) {
if (sc->tulip_probe_timeout > 0) {
tulip_timeout(sc);
return;
}
printf(TULIP_PRINTF_FMT "(phy%d): error: reset of PHY never completed!\n",
TULIP_PRINTF_ARGS, phyaddr);
sc->tulip_flags &= ~TULIP_TXPROBE_ACTIVE;
sc->tulip_probe_state = TULIP_PROBE_FAILED;
sc->tulip_if.if_flags &= ~(IFF_UP|IFF_RUNNING);
return;
}
status = tulip_mii_readreg(sc, phyaddr, PHYREG_STATUS);
if ((status & PHYSTS_CAN_AUTONEG) == 0) {
#if defined(TULIP_DEBUG)
loudprintf(TULIP_PRINTF_FMT "(phy%d): autonegotiation disabled\n",
TULIP_PRINTF_ARGS, phyaddr);
#endif
sc->tulip_flags &= ~TULIP_DIDNWAY;
sc->tulip_probe_state = TULIP_PROBE_MEDIATEST;
return;
}
if (tulip_mii_readreg(sc, phyaddr, PHYREG_AUTONEG_ADVERTISEMENT) != ((status >> 6) | 0x01))
tulip_mii_writereg(sc, phyaddr, PHYREG_AUTONEG_ADVERTISEMENT, (status >> 6) | 0x01);
tulip_mii_writereg(sc, phyaddr, PHYREG_CONTROL, data|PHYCTL_AUTONEG_RESTART|PHYCTL_AUTONEG_ENABLE);
data = tulip_mii_readreg(sc, phyaddr, PHYREG_CONTROL);
#if defined(TULIP_DEBUG)
if ((data & PHYCTL_AUTONEG_ENABLE) == 0)
loudprintf(TULIP_PRINTF_FMT "(phy%d): oops: enable autonegotiation failed: 0x%04x\n",
TULIP_PRINTF_ARGS, phyaddr, data);
else
loudprintf(TULIP_PRINTF_FMT "(phy%d): autonegotiation restarted: 0x%04x\n",
TULIP_PRINTF_ARGS, phyaddr, data);
sc->tulip_dbg.dbg_nway_starts++;
#endif
sc->tulip_probe_state = TULIP_PROBE_PHYAUTONEG;
sc->tulip_probe_timeout = 3000;
/* FALL THROUGH */
}
case TULIP_PROBE_PHYAUTONEG: {
u_int32_t status = tulip_mii_readreg(sc, phyaddr, PHYREG_STATUS);
u_int32_t data;
if ((status & PHYSTS_AUTONEG_DONE) == 0) {
if (sc->tulip_probe_timeout > 0) {
tulip_timeout(sc);
return;
}
#if defined(TULIP_DEBUG)
loudprintf(TULIP_PRINTF_FMT "(phy%d): autonegotiation timeout: sts=0x%04x, ctl=0x%04x\n",
TULIP_PRINTF_ARGS, phyaddr, status,
tulip_mii_readreg(sc, phyaddr, PHYREG_CONTROL));
#endif
sc->tulip_flags &= ~TULIP_DIDNWAY;
sc->tulip_probe_state = TULIP_PROBE_MEDIATEST;
return;
}
data = tulip_mii_readreg(sc, phyaddr, PHYREG_AUTONEG_ABILITIES);
#if defined(TULIP_DEBUG)
loudprintf(TULIP_PRINTF_FMT "(phy%d): autonegotiation complete: 0x%04x\n",
TULIP_PRINTF_ARGS, phyaddr, data);
#endif
data = (data << 6) & status;
if (!tulip_mii_map_abilities(sc, data))
sc->tulip_flags &= ~TULIP_DIDNWAY;
return;
}
default: {
#if defined(DIAGNOSTIC)
panic("tulip_media_poll: botch at line %d\n", __LINE__);
#endif
break;
}
}
#if defined(TULIP_DEBUG)
loudprintf(TULIP_PRINTF_FMT "(phy%d): autonegotiation failure: state = %d\n",
TULIP_PRINTF_ARGS, phyaddr, sc->tulip_probe_state);
sc->tulip_dbg.dbg_nway_failures++;
#endif
}
static void
tulip_2114x_media_preset(
tulip_softc_t * const sc)
{
const tulip_media_info_t *mi = NULL;
tulip_media_t media = sc->tulip_media;
if (sc->tulip_probe_state == TULIP_PROBE_INACTIVE)
media = sc->tulip_media;
else
media = sc->tulip_probe_media;
sc->tulip_cmdmode &= ~TULIP_CMD_PORTSELECT;
sc->tulip_flags &= ~TULIP_SQETEST;
if (media != TULIP_MEDIA_UNKNOWN) {
#if defined(TULIP_DEBUG)
if (media < TULIP_MEDIA_MAX && sc->tulip_mediums[media] != NULL) {
#endif
mi = sc->tulip_mediums[media];
if (mi->mi_type == TULIP_MEDIAINFO_MII) {
sc->tulip_cmdmode |= TULIP_CMD_PORTSELECT;
} else if (mi->mi_type == TULIP_MEDIAINFO_GPR
|| mi->mi_type == TULIP_MEDIAINFO_SYM) {
sc->tulip_cmdmode &= ~TULIP_GPR_CMDBITS;
sc->tulip_cmdmode |= mi->mi_cmdmode;
} else if (mi->mi_type == TULIP_MEDIAINFO_SIA) {
TULIP_CSR_WRITE(sc, csr_sia_connectivity, TULIP_SIACONN_RESET);
}
#if defined(TULIP_DEBUG)
} else {
printf(TULIP_PRINTF_FMT ": preset: bad media %d!\n",
TULIP_PRINTF_ARGS, media);
}
#endif
}
switch (media) {
case TULIP_MEDIA_BNC:
case TULIP_MEDIA_AUI:
case TULIP_MEDIA_10BASET: {
sc->tulip_cmdmode &= ~TULIP_CMD_FULLDUPLEX;
sc->tulip_cmdmode |= TULIP_CMD_TXTHRSHLDCTL;
sc->tulip_if.if_baudrate = 10000000;
sc->tulip_flags |= TULIP_SQETEST;
break;
}
case TULIP_MEDIA_10BASET_FD: {
sc->tulip_cmdmode |= TULIP_CMD_FULLDUPLEX|TULIP_CMD_TXTHRSHLDCTL;
sc->tulip_if.if_baudrate = 10000000;
break;
}
case TULIP_MEDIA_100BASEFX:
case TULIP_MEDIA_100BASET4:
case TULIP_MEDIA_100BASETX: {
sc->tulip_cmdmode &= ~(TULIP_CMD_FULLDUPLEX|TULIP_CMD_TXTHRSHLDCTL);
sc->tulip_cmdmode |= TULIP_CMD_PORTSELECT;
sc->tulip_if.if_baudrate = 100000000;
break;
}
case TULIP_MEDIA_100BASEFX_FD:
case TULIP_MEDIA_100BASETX_FD: {
sc->tulip_cmdmode |= TULIP_CMD_FULLDUPLEX|TULIP_CMD_PORTSELECT;
sc->tulip_cmdmode &= ~TULIP_CMD_TXTHRSHLDCTL;
sc->tulip_if.if_baudrate = 100000000;
break;
}
default: {
break;
}
}
TULIP_CSR_WRITE(sc, csr_command, sc->tulip_cmdmode);
}
/*
********************************************************************
* Start of 21140/21140A support which does not use the MII interface
*/
static void
tulip_null_media_poll(
tulip_softc_t * const sc,
tulip_mediapoll_event_t event)
{
#if defined(TULIP_DEBUG)
sc->tulip_dbg.dbg_events[event]++;
#endif
#if defined(DIAGNOSTIC)
printf(TULIP_PRINTF_FMT ": botch(media_poll) at line %d\n",
TULIP_PRINTF_ARGS, __LINE__);
#endif
}
__inline__ static void
tulip_21140_mediainit(
tulip_softc_t * const sc,
tulip_media_info_t * const mip,
tulip_media_t const media,
unsigned gpdata,
unsigned cmdmode)
{
sc->tulip_mediums[media] = mip;
mip->mi_type = TULIP_MEDIAINFO_GPR;
mip->mi_cmdmode = cmdmode;
mip->mi_gpdata = gpdata;
}
static void
tulip_21140_evalboard_media_probe(
tulip_softc_t * const sc)
{
tulip_media_info_t *mip = sc->tulip_mediainfo;
sc->tulip_gpinit = TULIP_GP_EB_PINS;
sc->tulip_gpdata = TULIP_GP_EB_INIT;
TULIP_CSR_WRITE(sc, csr_gp, TULIP_GP_EB_PINS);
TULIP_CSR_WRITE(sc, csr_gp, TULIP_GP_EB_INIT);
TULIP_CSR_WRITE(sc, csr_command,
TULIP_CSR_READ(sc, csr_command) | TULIP_CMD_PORTSELECT |
TULIP_CMD_PCSFUNCTION | TULIP_CMD_SCRAMBLER | TULIP_CMD_MUSTBEONE);
TULIP_CSR_WRITE(sc, csr_command,
TULIP_CSR_READ(sc, csr_command) & ~TULIP_CMD_TXTHRSHLDCTL);
DELAY(1000000);
if ((TULIP_CSR_READ(sc, csr_gp) & TULIP_GP_EB_OK100) != 0) {
sc->tulip_media = TULIP_MEDIA_10BASET;
} else {
sc->tulip_media = TULIP_MEDIA_100BASETX;
}
tulip_21140_mediainit(sc, mip++, TULIP_MEDIA_10BASET,
TULIP_GP_EB_INIT,
TULIP_CMD_TXTHRSHLDCTL);
tulip_21140_mediainit(sc, mip++, TULIP_MEDIA_10BASET_FD,
TULIP_GP_EB_INIT,
TULIP_CMD_TXTHRSHLDCTL|TULIP_CMD_FULLDUPLEX);
tulip_21140_mediainit(sc, mip++, TULIP_MEDIA_100BASETX,
TULIP_GP_EB_INIT,
TULIP_CMD_PORTSELECT|TULIP_CMD_PCSFUNCTION
|TULIP_CMD_SCRAMBLER);
tulip_21140_mediainit(sc, mip++, TULIP_MEDIA_100BASETX_FD,
TULIP_GP_EB_INIT,
TULIP_CMD_PORTSELECT|TULIP_CMD_PCSFUNCTION
|TULIP_CMD_SCRAMBLER|TULIP_CMD_FULLDUPLEX);
}
static const tulip_boardsw_t tulip_21140_eb_boardsw = {
TULIP_21140_DEC_EB,
tulip_21140_evalboard_media_probe,
tulip_media_select,
tulip_null_media_poll,
tulip_2114x_media_preset,
};
static void
tulip_21140_smc9332_media_probe(
tulip_softc_t * const sc)
{
tulip_media_info_t *mip = sc->tulip_mediainfo;
int idx, cnt = 0;
TULIP_CSR_WRITE(sc, csr_command, TULIP_CMD_PORTSELECT|TULIP_CMD_MUSTBEONE);
TULIP_CSR_WRITE(sc, csr_busmode, TULIP_BUSMODE_SWRESET);
DELAY(10); /* Wait 10 microseconds (actually 50 PCI cycles but at
33MHz that comes to two microseconds but wait a
bit longer anyways) */
TULIP_CSR_WRITE(sc, csr_command, TULIP_CMD_PORTSELECT |
TULIP_CMD_PCSFUNCTION | TULIP_CMD_SCRAMBLER | TULIP_CMD_MUSTBEONE);
sc->tulip_gpinit = TULIP_GP_SMC_9332_PINS;
sc->tulip_gpdata = TULIP_GP_SMC_9332_INIT;
TULIP_CSR_WRITE(sc, csr_gp, TULIP_GP_SMC_9332_PINS|TULIP_GP_PINSET);
TULIP_CSR_WRITE(sc, csr_gp, TULIP_GP_SMC_9332_INIT);
DELAY(200000);
for (idx = 1000; idx > 0; idx--) {
u_int32_t csr = TULIP_CSR_READ(sc, csr_gp);
if ((csr & (TULIP_GP_SMC_9332_OK10|TULIP_GP_SMC_9332_OK100)) == (TULIP_GP_SMC_9332_OK10|TULIP_GP_SMC_9332_OK100)) {
if (++cnt > 100)
break;
} else if ((csr & TULIP_GP_SMC_9332_OK10) == 0) {
break;
} else {
cnt = 0;
}
DELAY(1000);
}
sc->tulip_media = cnt > 100 ? TULIP_MEDIA_100BASETX : TULIP_MEDIA_10BASET;
tulip_21140_mediainit(sc, mip++, TULIP_MEDIA_100BASETX,
TULIP_GP_SMC_9332_INIT,
TULIP_CMD_PORTSELECT|TULIP_CMD_PCSFUNCTION
|TULIP_CMD_SCRAMBLER);
tulip_21140_mediainit(sc, mip++, TULIP_MEDIA_100BASETX_FD,
TULIP_GP_SMC_9332_INIT,
TULIP_CMD_PORTSELECT|TULIP_CMD_PCSFUNCTION
|TULIP_CMD_SCRAMBLER|TULIP_CMD_FULLDUPLEX);
tulip_21140_mediainit(sc, mip++, TULIP_MEDIA_10BASET,
TULIP_GP_SMC_9332_INIT,
TULIP_CMD_TXTHRSHLDCTL);
tulip_21140_mediainit(sc, mip++, TULIP_MEDIA_10BASET_FD,
TULIP_GP_SMC_9332_INIT,
TULIP_CMD_TXTHRSHLDCTL|TULIP_CMD_FULLDUPLEX);
}
static const tulip_boardsw_t tulip_21140_smc9332_boardsw = {
TULIP_21140_SMC_9332,
tulip_21140_smc9332_media_probe,
tulip_media_select,
tulip_null_media_poll,
tulip_2114x_media_preset,
};
static void
tulip_21140_cogent_em100_media_probe(
tulip_softc_t * const sc)
{
tulip_media_info_t *mip = sc->tulip_mediainfo;
u_int32_t cmdmode = TULIP_CSR_READ(sc, csr_command);
sc->tulip_gpinit = TULIP_GP_EM100_PINS;
sc->tulip_gpdata = TULIP_GP_EM100_INIT;
TULIP_CSR_WRITE(sc, csr_gp, TULIP_GP_EM100_PINS);
TULIP_CSR_WRITE(sc, csr_gp, TULIP_GP_EM100_INIT);
cmdmode = TULIP_CMD_PORTSELECT|TULIP_CMD_PCSFUNCTION|TULIP_CMD_MUSTBEONE;
cmdmode &= ~(TULIP_CMD_TXTHRSHLDCTL|TULIP_CMD_SCRAMBLER);
if (sc->tulip_rombuf[32] == TULIP_COGENT_EM100FX_ID) {
TULIP_CSR_WRITE(sc, csr_command, cmdmode);
sc->tulip_media = TULIP_MEDIA_100BASEFX;
tulip_21140_mediainit(sc, mip++, TULIP_MEDIA_100BASEFX,
TULIP_GP_EM100_INIT,
TULIP_CMD_PORTSELECT|TULIP_CMD_PCSFUNCTION);
tulip_21140_mediainit(sc, mip++, TULIP_MEDIA_100BASEFX_FD,
TULIP_GP_EM100_INIT,
TULIP_CMD_PORTSELECT|TULIP_CMD_PCSFUNCTION
|TULIP_CMD_FULLDUPLEX);
} else {
TULIP_CSR_WRITE(sc, csr_command, cmdmode|TULIP_CMD_SCRAMBLER);
sc->tulip_media = TULIP_MEDIA_100BASETX;
tulip_21140_mediainit(sc, mip++, TULIP_MEDIA_100BASETX,
TULIP_GP_EM100_INIT,
TULIP_CMD_PORTSELECT|TULIP_CMD_PCSFUNCTION
|TULIP_CMD_SCRAMBLER);
tulip_21140_mediainit(sc, mip++, TULIP_MEDIA_100BASETX_FD,
TULIP_GP_EM100_INIT,
TULIP_CMD_PORTSELECT|TULIP_CMD_PCSFUNCTION
|TULIP_CMD_SCRAMBLER|TULIP_CMD_FULLDUPLEX);
}
}
static const tulip_boardsw_t tulip_21140_cogent_em100_boardsw = {
TULIP_21140_COGENT_EM100,
tulip_21140_cogent_em100_media_probe,
tulip_media_select,
tulip_null_media_poll,
tulip_2114x_media_preset
};
static void
tulip_21140_znyx_zx34x_media_probe(
tulip_softc_t * const sc)
{
tulip_media_info_t *mip = sc->tulip_mediainfo;
int cnt10 = 0, cnt100 = 0, idx;
sc->tulip_gpinit = TULIP_GP_ZX34X_PINS;
sc->tulip_gpdata = TULIP_GP_ZX34X_INIT;
TULIP_CSR_WRITE(sc, csr_gp, TULIP_GP_ZX34X_PINS);
TULIP_CSR_WRITE(sc, csr_gp, TULIP_GP_ZX34X_INIT);
TULIP_CSR_WRITE(sc, csr_command,
TULIP_CSR_READ(sc, csr_command) | TULIP_CMD_PORTSELECT |
TULIP_CMD_PCSFUNCTION | TULIP_CMD_SCRAMBLER | TULIP_CMD_MUSTBEONE);
TULIP_CSR_WRITE(sc, csr_command,
TULIP_CSR_READ(sc, csr_command) & ~TULIP_CMD_TXTHRSHLDCTL);
DELAY(200000);
for (idx = 1000; idx > 0; idx--) {
u_int32_t csr = TULIP_CSR_READ(sc, csr_gp);
if ((csr & (TULIP_GP_ZX34X_LNKFAIL|TULIP_GP_ZX34X_SYMDET|TULIP_GP_ZX34X_SIGDET)) == (TULIP_GP_ZX34X_LNKFAIL|TULIP_GP_ZX34X_SYMDET|TULIP_GP_ZX34X_SIGDET)) {
if (++cnt100 > 100)
break;
} else if ((csr & TULIP_GP_ZX34X_LNKFAIL) == 0) {
if (++cnt10 > 100)
break;
} else {
cnt10 = 0;
cnt100 = 0;
}
DELAY(1000);
}
sc->tulip_media = cnt100 > 100 ? TULIP_MEDIA_100BASETX : TULIP_MEDIA_10BASET;
tulip_21140_mediainit(sc, mip++, TULIP_MEDIA_10BASET,
TULIP_GP_ZX34X_INIT,
TULIP_CMD_TXTHRSHLDCTL);
tulip_21140_mediainit(sc, mip++, TULIP_MEDIA_10BASET_FD,
TULIP_GP_ZX34X_INIT,
TULIP_CMD_TXTHRSHLDCTL|TULIP_CMD_FULLDUPLEX);
tulip_21140_mediainit(sc, mip++, TULIP_MEDIA_100BASETX,
TULIP_GP_ZX34X_INIT,
TULIP_CMD_PORTSELECT|TULIP_CMD_PCSFUNCTION
|TULIP_CMD_SCRAMBLER);
tulip_21140_mediainit(sc, mip++, TULIP_MEDIA_100BASETX_FD,
TULIP_GP_ZX34X_INIT,
TULIP_CMD_PORTSELECT|TULIP_CMD_PCSFUNCTION
|TULIP_CMD_SCRAMBLER|TULIP_CMD_FULLDUPLEX);
}
static const tulip_boardsw_t tulip_21140_znyx_zx34x_boardsw = {
TULIP_21140_ZNYX_ZX34X,
tulip_21140_znyx_zx34x_media_probe,
tulip_media_select,
tulip_null_media_poll,
tulip_2114x_media_preset,
};
static void
tulip_2114x_media_probe(
tulip_softc_t * const sc)
{
sc->tulip_cmdmode |= TULIP_CMD_MUSTBEONE
|TULIP_CMD_BACKOFFCTR|TULIP_CMD_THRSHLD72;
}
static const tulip_boardsw_t tulip_2114x_isv_boardsw = {
TULIP_21140_ISV,
tulip_2114x_media_probe,
tulip_media_select,
tulip_media_poll,
tulip_2114x_media_preset,
};
/*
* ******** END of chip-specific handlers. ***********
*/
/*
* Code the read the SROM and MII bit streams (I2C)
*/
static void
tulip_delay_300ns(
tulip_softc_t * const sc)
{
int idx;
for (idx = (300 / 33) + 1; idx > 0; idx--)
(void) TULIP_CSR_READ(sc, csr_busmode);
}
#define EMIT do { TULIP_CSR_WRITE(sc, csr_srom_mii, csr); tulip_delay_300ns(sc); } while (0)
static void
tulip_srom_idle(
tulip_softc_t * const sc)
{
unsigned bit, csr;
csr = SROMSEL ; EMIT;
csr = SROMSEL | SROMRD; EMIT;
csr ^= SROMCS; EMIT;
csr ^= SROMCLKON; EMIT;
/*
* Write 25 cycles of 0 which will force the SROM to be idle.
*/
for (bit = 3 + SROM_BITWIDTH + 16; bit > 0; bit--) {
csr ^= SROMCLKOFF; EMIT; /* clock low; data not valid */
csr ^= SROMCLKON; EMIT; /* clock high; data valid */
}
csr ^= SROMCLKOFF; EMIT;
csr ^= SROMCS; EMIT;
csr = 0; EMIT;
}
static void
tulip_srom_read(
tulip_softc_t * const sc)
{
unsigned idx;
const unsigned bitwidth = SROM_BITWIDTH;
const unsigned cmdmask = (SROMCMD_RD << bitwidth);
const unsigned msb = 1 << (bitwidth + 3 - 1);
unsigned lastidx = (1 << bitwidth) - 1;
tulip_srom_idle(sc);
for (idx = 0; idx <= lastidx; idx++) {
unsigned lastbit, data, bits, bit, csr;
csr = SROMSEL ; EMIT;
csr = SROMSEL | SROMRD; EMIT;
csr ^= SROMCSON; EMIT;
csr ^= SROMCLKON; EMIT;
lastbit = 0;
for (bits = idx|cmdmask, bit = bitwidth + 3; bit > 0; bit--, bits <<= 1) {
const unsigned thisbit = bits & msb;
csr ^= SROMCLKOFF; EMIT; /* clock low; data not valid */
if (thisbit != lastbit) {
csr ^= SROMDOUT; EMIT; /* clock low; invert data */
} else {
EMIT;
}
csr ^= SROMCLKON; EMIT; /* clock high; data valid */
lastbit = thisbit;
}
csr ^= SROMCLKOFF; EMIT;
for (data = 0, bits = 0; bits < 16; bits++) {
data <<= 1;
csr ^= SROMCLKON; EMIT; /* clock high; data valid */
data |= TULIP_CSR_READ(sc, csr_srom_mii) & SROMDIN ? 1 : 0;
csr ^= SROMCLKOFF; EMIT; /* clock low; data not valid */
}
sc->tulip_rombuf[idx*2] = data & 0xFF;
sc->tulip_rombuf[idx*2+1] = data >> 8;
csr = SROMSEL | SROMRD; EMIT;
csr = 0; EMIT;
}
tulip_srom_idle(sc);
}
#define MII_EMIT do { TULIP_CSR_WRITE(sc, csr_srom_mii, csr); tulip_delay_300ns(sc); } while (0)
static void
tulip_mii_writebits(
tulip_softc_t * const sc,
unsigned data,
unsigned bits)
{
unsigned msb = 1 << (bits - 1);
unsigned csr = TULIP_CSR_READ(sc, csr_srom_mii) & (MII_RD|MII_DOUT|MII_CLK);
unsigned lastbit = (csr & MII_DOUT) ? msb : 0;
csr |= MII_WR; MII_EMIT; /* clock low; assert write */
for (; bits > 0; bits--, data <<= 1) {
const unsigned thisbit = data & msb;
if (thisbit != lastbit) {
csr ^= MII_DOUT; MII_EMIT; /* clock low; invert data */
}
csr ^= MII_CLKON; MII_EMIT; /* clock high; data valid */
lastbit = thisbit;
csr ^= MII_CLKOFF; MII_EMIT; /* clock low; data not valid */
}
}
static void
tulip_mii_turnaround(
tulip_softc_t * const sc,
unsigned cmd)
{
unsigned csr = TULIP_CSR_READ(sc, csr_srom_mii) & (MII_RD|MII_DOUT|MII_CLK);
if (cmd == MII_WRCMD) {
csr |= MII_DOUT; MII_EMIT; /* clock low; change data */
csr ^= MII_CLKON; MII_EMIT; /* clock high; data valid */
csr ^= MII_CLKOFF; MII_EMIT; /* clock low; data not valid */
csr ^= MII_DOUT; MII_EMIT; /* clock low; change data */
} else {
csr |= MII_RD; MII_EMIT; /* clock low; switch to read */
}
csr ^= MII_CLKON; MII_EMIT; /* clock high; data valid */
csr ^= MII_CLKOFF; MII_EMIT; /* clock low; data not valid */
}
static unsigned
tulip_mii_readbits(
tulip_softc_t * const sc)
{
unsigned data;
unsigned csr = TULIP_CSR_READ(sc, csr_srom_mii) & (MII_RD|MII_DOUT|MII_CLK);
int idx;
for (idx = 0, data = 0; idx < 16; idx++) {
data <<= 1; /* this is NOOP on the first pass through */
csr ^= MII_CLKON; MII_EMIT; /* clock high; data valid */
if (TULIP_CSR_READ(sc, csr_srom_mii) & MII_DIN)
data |= 1;
csr ^= MII_CLKOFF; MII_EMIT; /* clock low; data not valid */
}
csr ^= MII_RD; MII_EMIT; /* clock low; turn off read */
return data;
}
static unsigned
tulip_mii_readreg(
tulip_softc_t * const sc,
unsigned devaddr,
unsigned regno)
{
unsigned csr = TULIP_CSR_READ(sc, csr_srom_mii) & (MII_RD|MII_DOUT|MII_CLK);
unsigned data;
csr &= ~(MII_RD|MII_CLK); MII_EMIT;
tulip_mii_writebits(sc, MII_PREAMBLE, 32);
tulip_mii_writebits(sc, MII_RDCMD, 8);
tulip_mii_writebits(sc, devaddr, 5);
tulip_mii_writebits(sc, regno, 5);
tulip_mii_turnaround(sc, MII_RDCMD);
data = tulip_mii_readbits(sc);
#if defined(TULIP_DEBUG)
sc->tulip_dbg.dbg_phyregs[regno][0] = data;
sc->tulip_dbg.dbg_phyregs[regno][1]++;
#endif
return data;
}
static void
tulip_mii_writereg(
tulip_softc_t * const sc,
unsigned devaddr,
unsigned regno,
unsigned data)
{
unsigned csr = TULIP_CSR_READ(sc, csr_srom_mii) & (MII_RD|MII_DOUT|MII_CLK);
csr &= ~(MII_RD|MII_CLK); MII_EMIT;
tulip_mii_writebits(sc, MII_PREAMBLE, 32);
tulip_mii_writebits(sc, MII_WRCMD, 8);
tulip_mii_writebits(sc, devaddr, 5);
tulip_mii_writebits(sc, regno, 5);
tulip_mii_turnaround(sc, MII_WRCMD);
tulip_mii_writebits(sc, data, 16);
#if defined(TULIP_DEBUG)
sc->tulip_dbg.dbg_phyregs[regno][2] = data;
sc->tulip_dbg.dbg_phyregs[regno][3]++;
#endif
}
#define tulip_mchash(mca) (tulip_crc32(mca, 6) & 0x1FF)
#define tulip_srom_crcok(databuf) ( \
((tulip_crc32(databuf, 126) & 0xFFFFU) ^ 0xFFFFU) == \
((databuf)[126] | ((databuf)[127] << 8)))
static unsigned
tulip_crc32(
const unsigned char *databuf,
size_t datalen)
{
u_int idx, bit, data, crc = 0xFFFFFFFFUL;
for (idx = 0; idx < datalen; idx++)
for (data = *databuf++, bit = 0; bit < 8; bit++, data >>= 1)
crc = (crc >> 1) ^ (((crc ^ data) & 1) ? TULIP_CRC32_POLY : 0);
return crc;
}
static void
tulip_identify_dec_nic(
tulip_softc_t * const sc)
{
strcpy(sc->tulip_boardid, "DEC ");
#define D0 4
if (sc->tulip_chipid <= TULIP_DE425)
return;
if (bcmp(sc->tulip_rombuf + 29, "DE500", 5) == 0
|| bcmp(sc->tulip_rombuf + 29, "DE450", 5) == 0) {
bcopy(sc->tulip_rombuf + 29, &sc->tulip_boardid[D0], 8);
sc->tulip_boardid[D0+8] = ' ';
}
#undef D0
}
static void
tulip_identify_znyx_nic(
tulip_softc_t * const sc)
{
unsigned id = 0;
strcpy(sc->tulip_boardid, "ZNYX ZX3XX ");
if (sc->tulip_chipid == TULIP_21140 || sc->tulip_chipid == TULIP_21140A) {
unsigned znyx_ptr;
sc->tulip_boardid[8] = '4';
znyx_ptr = sc->tulip_rombuf[124] + 256 * sc->tulip_rombuf[125];
if (znyx_ptr < 26 || znyx_ptr > 116) {
sc->tulip_boardsw = &tulip_21140_znyx_zx34x_boardsw;
return;
}
/* ZX344 = 0010 .. 0013FF
*/
if (sc->tulip_rombuf[znyx_ptr] == 0x4A
&& sc->tulip_rombuf[znyx_ptr + 1] == 0x52
&& sc->tulip_rombuf[znyx_ptr + 2] == 0x01) {
id = sc->tulip_rombuf[znyx_ptr + 5] + 256 * sc->tulip_rombuf[znyx_ptr + 4];
if ((id >> 8) == (TULIP_ZNYX_ID_ZX342 >> 8)) {
sc->tulip_boardid[9] = '2';
if (id == TULIP_ZNYX_ID_ZX342B) {
sc->tulip_boardid[10] = 'B';
sc->tulip_boardid[11] = ' ';
}
sc->tulip_boardsw = &tulip_21140_znyx_zx34x_boardsw;
} else if (id == TULIP_ZNYX_ID_ZX344) {
sc->tulip_boardid[10] = '4';
sc->tulip_boardsw = &tulip_21140_znyx_zx34x_boardsw;
} else if (id == TULIP_ZNYX_ID_ZX345) {
sc->tulip_boardid[9] = (sc->tulip_rombuf[19] > 1) ? '8' : '5';
} else if (id == TULIP_ZNYX_ID_ZX346) {
sc->tulip_boardid[9] = '6';
} else if (id == TULIP_ZNYX_ID_ZX351) {
sc->tulip_boardid[8] = '5';
sc->tulip_boardid[9] = '1';
}
}
if (id == 0) {
/*
* Assume it's a ZX342...
*/
sc->tulip_boardsw = &tulip_21140_znyx_zx34x_boardsw;
}
return;
}
sc->tulip_boardid[8] = '1';
if (sc->tulip_chipid == TULIP_21041) {
sc->tulip_boardid[10] = '1';
return;
}
if (sc->tulip_rombuf[32] == 0x4A && sc->tulip_rombuf[33] == 0x52) {
id = sc->tulip_rombuf[37] + 256 * sc->tulip_rombuf[36];
if (id == TULIP_ZNYX_ID_ZX312T) {
sc->tulip_boardid[9] = '2';
sc->tulip_boardid[10] = 'T';
sc->tulip_boardid[11] = ' ';
sc->tulip_boardsw = &tulip_21040_10baset_only_boardsw;
} else if (id == TULIP_ZNYX_ID_ZX314_INTA) {
sc->tulip_boardid[9] = '4';
sc->tulip_boardsw = &tulip_21040_10baset_only_boardsw;
sc->tulip_features |= TULIP_HAVE_SHAREDINTR|TULIP_HAVE_BASEROM;
} else if (id == TULIP_ZNYX_ID_ZX314) {
sc->tulip_boardid[9] = '4';
sc->tulip_boardsw = &tulip_21040_10baset_only_boardsw;
sc->tulip_features |= TULIP_HAVE_BASEROM;
} else if (id == TULIP_ZNYX_ID_ZX315_INTA) {
sc->tulip_boardid[9] = '5';
sc->tulip_features |= TULIP_HAVE_SHAREDINTR|TULIP_HAVE_BASEROM;
} else if (id == TULIP_ZNYX_ID_ZX315) {
sc->tulip_boardid[9] = '5';
sc->tulip_features |= TULIP_HAVE_BASEROM;
} else {
id = 0;
}
}
if (id == 0) {
if ((sc->tulip_enaddr[3] & ~3) == 0xF0 && (sc->tulip_enaddr[5] & 3) == 0) {
sc->tulip_boardid[9] = '4';
sc->tulip_boardsw = &tulip_21040_10baset_only_boardsw;
sc->tulip_features |= TULIP_HAVE_SHAREDINTR|TULIP_HAVE_BASEROM;
} else if ((sc->tulip_enaddr[3] & ~3) == 0xF4 && (sc->tulip_enaddr[5] & 1) == 0) {
sc->tulip_boardid[9] = '5';
sc->tulip_boardsw = &tulip_21040_boardsw;
sc->tulip_features |= TULIP_HAVE_SHAREDINTR|TULIP_HAVE_BASEROM;
} else if ((sc->tulip_enaddr[3] & ~3) == 0xEC) {
sc->tulip_boardid[9] = '2';
sc->tulip_boardsw = &tulip_21040_boardsw;
}
}
}
static void
tulip_identify_smc_nic(
tulip_softc_t * const sc)
{
u_int32_t id1, id2, ei;
int auibnc = 0, utp = 0;
char *cp;
strcpy(sc->tulip_boardid, "SMC ");
if (sc->tulip_chipid == TULIP_21041)
return;
if (sc->tulip_chipid != TULIP_21040) {
if (sc->tulip_boardsw != &tulip_2114x_isv_boardsw) {
strcpy(&sc->tulip_boardid[4], "9332DST ");
sc->tulip_boardsw = &tulip_21140_smc9332_boardsw;
} else if (sc->tulip_features & (TULIP_HAVE_BASEROM|TULIP_HAVE_SLAVEDROM)) {
strcpy(&sc->tulip_boardid[4], "9334BDT ");
} else {
strcpy(&sc->tulip_boardid[4], "9332BDT ");
}
return;
}
id1 = sc->tulip_rombuf[0x60] | (sc->tulip_rombuf[0x61] << 8);
id2 = sc->tulip_rombuf[0x62] | (sc->tulip_rombuf[0x63] << 8);
ei = sc->tulip_rombuf[0x66] | (sc->tulip_rombuf[0x67] << 8);
strcpy(&sc->tulip_boardid[4], "8432");
cp = &sc->tulip_boardid[8];
if ((id1 & 1) == 0)
*cp++ = 'B', auibnc = 1;
if ((id1 & 0xFF) > 0x32)
*cp++ = 'T', utp = 1;
if ((id1 & 0x4000) == 0)
*cp++ = 'A', auibnc = 1;
if (id2 == 0x15) {
sc->tulip_boardid[7] = '4';
*cp++ = '-';
*cp++ = 'C';
*cp++ = 'H';
*cp++ = (ei ? '2' : '1');
}
*cp++ = ' ';
*cp = '\0';
if (utp && !auibnc)
sc->tulip_boardsw = &tulip_21040_10baset_only_boardsw;
else if (!utp && auibnc)
sc->tulip_boardsw = &tulip_21040_auibnc_only_boardsw;
}
static void
tulip_identify_cogent_nic(
tulip_softc_t * const sc)
{
strcpy(sc->tulip_boardid, "Cogent ");
if (sc->tulip_chipid == TULIP_21140 || sc->tulip_chipid == TULIP_21140A) {
if (sc->tulip_rombuf[32] == TULIP_COGENT_EM100TX_ID) {
strcat(sc->tulip_boardid, "EM100FX ");
sc->tulip_boardsw = &tulip_21140_cogent_em100_boardsw;
} else if (sc->tulip_rombuf[32] == TULIP_COGENT_EM100FX_ID) {
strcat(sc->tulip_boardid, "EM100FX ");
sc->tulip_boardsw = &tulip_21140_cogent_em100_boardsw;
}
/*
* Magic number (0x24001109U) is the SubVendor (0x2400) and
* SubDevId (0x1109) for the ANA6944TX (EM440TX).
*/
if (*(u_int32_t *) sc->tulip_rombuf == 0x24001109U
&& (sc->tulip_features & TULIP_HAVE_BASEROM)) {
/*
* Cogent (Adaptec) is still mapping all INTs to INTA of
* first 21140. Dumb! Dumb!
*/
strcat(sc->tulip_boardid, "EM440TX ");
sc->tulip_features |= TULIP_HAVE_SHAREDINTR;
}
} else if (sc->tulip_chipid == TULIP_21040) {
sc->tulip_features |= TULIP_HAVE_SHAREDINTR|TULIP_HAVE_BASEROM;
}
}
static void
tulip_identify_asante_nic(
tulip_softc_t * const sc)
{
strcpy(sc->tulip_boardid, "Asante ");
if ((sc->tulip_chipid == TULIP_21140 || sc->tulip_chipid == TULIP_21140A)
&& sc->tulip_boardsw != &tulip_2114x_isv_boardsw) {
tulip_media_info_t *mi = sc->tulip_mediainfo;
int idx;
/*
* The Asante Fast Ethernet doesn't always ship with a valid
* new format SROM. So if isn't in the new format, we cheat
* set it up as if we had.
*/
sc->tulip_gpinit = TULIP_GP_ASANTE_PINS;
sc->tulip_gpdata = 0;
TULIP_CSR_WRITE(sc, csr_gp, TULIP_GP_ASANTE_PINS|TULIP_GP_PINSET);
TULIP_CSR_WRITE(sc, csr_gp, TULIP_GP_ASANTE_PHYRESET);
DELAY(100);
TULIP_CSR_WRITE(sc, csr_gp, 0);
mi->mi_type = TULIP_MEDIAINFO_MII;
mi->mi_gpr_length = 0;
mi->mi_gpr_offset = 0;
mi->mi_reset_length = 0;
mi->mi_reset_offset = 0;;
mi->mi_phyaddr = TULIP_MII_NOPHY;
for (idx = 20; idx > 0 && mi->mi_phyaddr == TULIP_MII_NOPHY; idx--) {
DELAY(10000);
mi->mi_phyaddr = tulip_mii_get_phyaddr(sc, 0);
}
if (mi->mi_phyaddr == TULIP_MII_NOPHY) {
printf(TULIP_PRINTF_FMT ": can't find phy 0\n", TULIP_PRINTF_ARGS);
return;
}
sc->tulip_features |= TULIP_HAVE_MII;
mi->mi_capabilities = PHYSTS_10BASET|PHYSTS_10BASET_FD|PHYSTS_100BASETX|PHYSTS_100BASETX_FD;
mi->mi_advertisement = PHYSTS_10BASET|PHYSTS_10BASET_FD|PHYSTS_100BASETX|PHYSTS_100BASETX_FD;
mi->mi_full_duplex = PHYSTS_10BASET_FD|PHYSTS_100BASETX_FD;
mi->mi_tx_threshold = PHYSTS_10BASET|PHYSTS_10BASET_FD;
TULIP_MEDIAINFO_ADD_CAPABILITY(sc, mi, 100BASETX_FD);
TULIP_MEDIAINFO_ADD_CAPABILITY(sc, mi, 100BASETX);
TULIP_MEDIAINFO_ADD_CAPABILITY(sc, mi, 100BASET4);
TULIP_MEDIAINFO_ADD_CAPABILITY(sc, mi, 10BASET_FD);
TULIP_MEDIAINFO_ADD_CAPABILITY(sc, mi, 10BASET);
mi->mi_phyid = (tulip_mii_readreg(sc, mi->mi_phyaddr, PHYREG_IDLOW) << 16) |
tulip_mii_readreg(sc, mi->mi_phyaddr, PHYREG_IDHIGH);
sc->tulip_boardsw = &tulip_2114x_isv_boardsw;
}
}
static int
tulip_srom_decode(
tulip_softc_t * const sc)
{
unsigned idx1, idx2, idx3;
const tulip_srom_header_t *shp = (tulip_srom_header_t *) &sc->tulip_rombuf[0];
const tulip_srom_adapter_info_t *saip = (tulip_srom_adapter_info_t *) (shp + 1);
tulip_srom_media_t srom_media;
tulip_media_info_t *mi = sc->tulip_mediainfo;
const u_int8_t *dp;
u_int32_t leaf_offset, blocks, data;
for (idx1 = 0; idx1 < shp->sh_adapter_count; idx1++, saip++) {
if (shp->sh_adapter_count == 1)
break;
if (saip->sai_device == sc->tulip_pci_devno)
break;
}
/*
* Didn't find the right media block for this card.
*/
if (idx1 == shp->sh_adapter_count)
return 0;
/*
* Save the hardware address.
*/
bcopy((caddr_t) shp->sh_ieee802_address, (caddr_t) sc->tulip_enaddr, 6);
/*
* If this is a multiple port card, add the adapter index to the last
* byte of the hardware address. (if it isn't multiport, adding 0
* won't hurt.
*/
sc->tulip_enaddr[5] += idx1;
leaf_offset = saip->sai_leaf_offset_lowbyte
+ saip->sai_leaf_offset_highbyte * 256;
dp = sc->tulip_rombuf + leaf_offset;
sc->tulip_conntype = (tulip_srom_connection_t) (dp[0] + dp[1] * 256); dp += 2;
for (idx2 = 0;; idx2++) {
if (tulip_srom_conninfo[idx2].sc_type == sc->tulip_conntype
|| tulip_srom_conninfo[idx2].sc_type == TULIP_SROM_CONNTYPE_NOT_USED)
break;
}
sc->tulip_connidx = idx2;
if (sc->tulip_chipid == TULIP_21041) {
blocks = *dp++;
for (idx2 = 0; idx2 < blocks; idx2++) {
tulip_media_t media;
data = *dp++;
srom_media = (tulip_srom_media_t) (data & 0x3F);
for (idx3 = 0; tulip_srom_mediums[idx3].sm_type != TULIP_MEDIA_UNKNOWN; idx3++) {
if (tulip_srom_mediums[idx3].sm_srom_type == srom_media)
break;
}
media = tulip_srom_mediums[idx3].sm_type;
if (media != TULIP_MEDIA_UNKNOWN) {
if (data & TULIP_SROM_21041_EXTENDED) {
mi->mi_type = TULIP_MEDIAINFO_SIA;
sc->tulip_mediums[media] = mi;
mi->mi_sia_connectivity = dp[0] + dp[1] * 256;
mi->mi_sia_tx_rx = dp[2] + dp[3] * 256;
mi->mi_sia_general = dp[4] + dp[5] * 256;
mi++;
} else {
switch (media) {
case TULIP_MEDIA_BNC: {
TULIP_MEDIAINFO_SIA_INIT(sc, mi, 21041, BNC);
mi++;
break;
}
case TULIP_MEDIA_AUI: {
TULIP_MEDIAINFO_SIA_INIT(sc, mi, 21041, AUI);
mi++;
break;
}
case TULIP_MEDIA_10BASET: {
TULIP_MEDIAINFO_SIA_INIT(sc, mi, 21041, 10BASET);
mi++;
break;
}
case TULIP_MEDIA_10BASET_FD: {
TULIP_MEDIAINFO_SIA_INIT(sc, mi, 21041, 10BASET_FD);
mi++;
break;
}
default: {
break;
}
}
}
}
if (data & TULIP_SROM_21041_EXTENDED)
dp += 6;
}
#ifdef notdef
if (blocks == 0) {
TULIP_MEDIAINFO_SIA_INIT(sc, mi, 21041, BNC); mi++;
TULIP_MEDIAINFO_SIA_INIT(sc, mi, 21041, AUI); mi++;
TULIP_MEDIAINFO_SIA_INIT(sc, mi, 21041, 10BASET); mi++;
TULIP_MEDIAINFO_SIA_INIT(sc, mi, 21041, 10BASET_FD); mi++;
}
#endif
} else {
unsigned length, type;
tulip_media_t gp_media = TULIP_MEDIA_UNKNOWN;
if (sc->tulip_features & TULIP_HAVE_GPR)
sc->tulip_gpinit = *dp++;
blocks = *dp++;
for (idx2 = 0; idx2 < blocks; idx2++) {
const u_int8_t *ep;
if ((*dp & 0x80) == 0) {
length = 4;
type = 0;
} else {
length = (*dp++ & 0x7f) - 1;
type = *dp++ & 0x3f;
}
ep = dp + length;
switch (type & 0x3f) {
case 0: { /* 21140[A] GPR block */
tulip_media_t media;
srom_media = (tulip_srom_media_t) dp[0];
for (idx3 = 0; tulip_srom_mediums[idx3].sm_type != TULIP_MEDIA_UNKNOWN; idx3++) {
if (tulip_srom_mediums[idx3].sm_srom_type == srom_media)
break;
}
media = tulip_srom_mediums[idx3].sm_type;
if (media == TULIP_MEDIA_UNKNOWN)
break;
mi->mi_type = TULIP_MEDIAINFO_GPR;
sc->tulip_mediums[media] = mi;
mi->mi_gpdata = dp[1];
if (media > gp_media && !TULIP_IS_MEDIA_FD(media)) {
sc->tulip_gpdata = mi->mi_gpdata;
gp_media = media;
}
data = dp[2] + dp[3] * 256;
mi->mi_cmdmode = TULIP_SROM_2114X_CMDBITS(data);
if (data & TULIP_SROM_2114X_NOINDICATOR) {
mi->mi_actmask = 0;
} else {
#if 0
mi->mi_default = (data & TULIP_SROM_2114X_DEFAULT) != 0;
#endif
mi->mi_actmask = TULIP_SROM_2114X_BITPOS(data);
mi->mi_actdata = (data & TULIP_SROM_2114X_POLARITY) ? 0 : mi->mi_actmask;
}
mi++;
break;
}
case 1: { /* 21140[A] MII block */
const unsigned phyno = *dp++;
mi->mi_type = TULIP_MEDIAINFO_MII;
mi->mi_gpr_length = *dp++;
mi->mi_gpr_offset = dp - sc->tulip_rombuf;
dp += mi->mi_gpr_length;
mi->mi_reset_length = *dp++;
mi->mi_reset_offset = dp - sc->tulip_rombuf;
dp += mi->mi_reset_length;
/*
* Before we probe for a PHY, use the GPR information
* to select it. If we don't, it may be inaccessible.
*/
TULIP_CSR_WRITE(sc, csr_gp, sc->tulip_gpinit|TULIP_GP_PINSET);
for (idx3 = 0; idx3 < mi->mi_reset_length; idx3++) {
DELAY(10);
TULIP_CSR_WRITE(sc, csr_gp, sc->tulip_rombuf[mi->mi_reset_offset + idx3]);
}
sc->tulip_phyaddr = mi->mi_phyaddr;
for (idx3 = 0; idx3 < mi->mi_gpr_length; idx3++) {
DELAY(10);
TULIP_CSR_WRITE(sc, csr_gp, sc->tulip_rombuf[mi->mi_gpr_offset + idx3]);
}
/*
* At least write something!
*/
if (mi->mi_reset_length == 0 && mi->mi_gpr_length == 0)
TULIP_CSR_WRITE(sc, csr_gp, 0);
mi->mi_phyaddr = TULIP_MII_NOPHY;
for (idx3 = 20; idx3 > 0 && mi->mi_phyaddr == TULIP_MII_NOPHY; idx3--) {
DELAY(10000);
mi->mi_phyaddr = tulip_mii_get_phyaddr(sc, phyno);
}
if (mi->mi_phyaddr == TULIP_MII_NOPHY) {
printf(TULIP_PRINTF_FMT ": can't find phy %d\n",
TULIP_PRINTF_ARGS, phyno);
break;
}
sc->tulip_features |= TULIP_HAVE_MII;
mi->mi_capabilities = dp[0] + dp[1] * 256; dp += 2;
mi->mi_advertisement = dp[0] + dp[1] * 256; dp += 2;
mi->mi_full_duplex = dp[0] + dp[1] * 256; dp += 2;
mi->mi_tx_threshold = dp[0] + dp[1] * 256; dp += 2;
TULIP_MEDIAINFO_ADD_CAPABILITY(sc, mi, 100BASETX_FD);
TULIP_MEDIAINFO_ADD_CAPABILITY(sc, mi, 100BASETX);
TULIP_MEDIAINFO_ADD_CAPABILITY(sc, mi, 100BASET4);
TULIP_MEDIAINFO_ADD_CAPABILITY(sc, mi, 10BASET_FD);
TULIP_MEDIAINFO_ADD_CAPABILITY(sc, mi, 10BASET);
mi->mi_phyid = (tulip_mii_readreg(sc, mi->mi_phyaddr, PHYREG_IDLOW) << 16) |
tulip_mii_readreg(sc, mi->mi_phyaddr, PHYREG_IDHIGH);
mi++;
break;
}
case 2: { /* 2114[23] SIA block */
tulip_media_t media;
srom_media = (tulip_srom_media_t) dp[0];
for (idx3 = 0; tulip_srom_mediums[idx3].sm_type != TULIP_MEDIA_UNKNOWN; idx3++) {
if (tulip_srom_mediums[idx3].sm_srom_type == srom_media)
break;
}
media = tulip_srom_mediums[idx3].sm_type;
if (media == TULIP_MEDIA_UNKNOWN)
break;
mi->mi_type = TULIP_MEDIAINFO_SIA;
sc->tulip_mediums[media] = mi;
if (type & 0x40) {
mi->mi_sia_connectivity = dp[0] + dp[1] * 256;
mi->mi_sia_tx_rx = dp[2] + dp[3] * 256;
mi->mi_sia_general = dp[4] + dp[5] * 256;
dp += 6;
} else {
switch (media) {
case TULIP_MEDIA_BNC: {
TULIP_MEDIAINFO_SIA_INIT(sc, mi, 21142, BNC);
break;
}
case TULIP_MEDIA_AUI: {
TULIP_MEDIAINFO_SIA_INIT(sc, mi, 21142, AUI);
break;
}
case TULIP_MEDIA_10BASET: {
TULIP_MEDIAINFO_SIA_INIT(sc, mi, 21142, 10BASET);
break;
}
case TULIP_MEDIA_10BASET_FD: {
TULIP_MEDIAINFO_SIA_INIT(sc, mi, 21142, 10BASET_FD);
break;
}
default: {
goto bad_media;
}
}
}
mi->mi_sia_gp_control = (dp[0] + dp[1] * 256) << 16;
mi->mi_sia_gp_data = (dp[2] + dp[3] * 256) << 16;
mi++;
bad_media:
break;
}
case 3: { /* 2114[23] MII PHY block */
const unsigned phyno = *dp++;
const u_int8_t *dp0;
mi->mi_type = TULIP_MEDIAINFO_MII;
mi->mi_gpr_length = *dp++;
mi->mi_gpr_offset = dp - sc->tulip_rombuf;
dp += 2 * mi->mi_gpr_length;
mi->mi_reset_length = *dp++;
mi->mi_reset_offset = dp - sc->tulip_rombuf;
dp += 2 * mi->mi_reset_length;
dp0 = &sc->tulip_rombuf[mi->mi_reset_offset];
for (idx3 = 0; idx3 < mi->mi_reset_length; idx3++, dp0 += 2) {
DELAY(10);
TULIP_CSR_WRITE(sc, csr_sia_general, (dp0[0] + 256 * dp0[1]) << 16);
}
sc->tulip_phyaddr = mi->mi_phyaddr;
dp0 = &sc->tulip_rombuf[mi->mi_gpr_offset];
for (idx3 = 0; idx3 < mi->mi_gpr_length; idx3++, dp0 += 2) {
DELAY(10);
TULIP_CSR_WRITE(sc, csr_sia_general, (dp0[0] + 256 * dp0[1]) << 16);
}
if (mi->mi_reset_length == 0 && mi->mi_gpr_length == 0)
TULIP_CSR_WRITE(sc, csr_sia_general, 0);
mi->mi_phyaddr = TULIP_MII_NOPHY;
for (idx3 = 20; idx3 > 0 && mi->mi_phyaddr == TULIP_MII_NOPHY; idx3--) {
DELAY(10000);
mi->mi_phyaddr = tulip_mii_get_phyaddr(sc, phyno);
}
if (mi->mi_phyaddr == TULIP_MII_NOPHY) {
printf(TULIP_PRINTF_FMT ": can't find phy %d\n",
TULIP_PRINTF_ARGS, phyno);
break;
}
sc->tulip_features |= TULIP_HAVE_MII;
mi->mi_capabilities = dp[0] + dp[1] * 256; dp += 2;
mi->mi_advertisement = dp[0] + dp[1] * 256; dp += 2;
mi->mi_full_duplex = dp[0] + dp[1] * 256; dp += 2;
mi->mi_tx_threshold = dp[0] + dp[1] * 256; dp += 2;
mi->mi_mii_interrupt = dp[0] + dp[1] * 256; dp += 2;
TULIP_MEDIAINFO_ADD_CAPABILITY(sc, mi, 100BASETX_FD);
TULIP_MEDIAINFO_ADD_CAPABILITY(sc, mi, 100BASETX);
TULIP_MEDIAINFO_ADD_CAPABILITY(sc, mi, 100BASET4);
TULIP_MEDIAINFO_ADD_CAPABILITY(sc, mi, 10BASET_FD);
TULIP_MEDIAINFO_ADD_CAPABILITY(sc, mi, 10BASET);
mi->mi_phyid = (tulip_mii_readreg(sc, mi->mi_phyaddr, PHYREG_IDLOW) << 16) |
tulip_mii_readreg(sc, mi->mi_phyaddr, PHYREG_IDHIGH);
mi++;
break;
}
case 4: { /* 21143 SYM block */
tulip_media_t media;
srom_media = (tulip_srom_media_t) dp[0];
for (idx3 = 0; tulip_srom_mediums[idx3].sm_type != TULIP_MEDIA_UNKNOWN; idx3++) {
if (tulip_srom_mediums[idx3].sm_srom_type == srom_media)
break;
}
media = tulip_srom_mediums[idx3].sm_type;
if (media == TULIP_MEDIA_UNKNOWN)
break;
mi->mi_type = TULIP_MEDIAINFO_SYM;
sc->tulip_mediums[media] = mi;
mi->mi_gpcontrol = (dp[1] + dp[2] * 256) << 16;
mi->mi_gpdata = (dp[3] + dp[4] * 256) << 16;
data = dp[5] + dp[6] * 256;
mi->mi_cmdmode = TULIP_SROM_2114X_CMDBITS(data);
if (data & TULIP_SROM_2114X_NOINDICATOR) {
mi->mi_actmask = 0;
} else {
mi->mi_default = (data & TULIP_SROM_2114X_DEFAULT) != 0;
mi->mi_actmask = TULIP_SROM_2114X_BITPOS(data);
mi->mi_actdata = (data & TULIP_SROM_2114X_POLARITY) ? 0 : mi->mi_actmask;
}
mi++;
break;
}
#if 0
case 5: { /* 21143 Reset block */
mi->mi_type = TULIP_MEDIAINFO_RESET;
mi->mi_reset_length = *dp++;
mi->mi_reset_offset = dp - sc->tulip_rombuf;
dp += 2 * mi->mi_reset_length;
mi++;
break;
}
#endif
default: {
}
}
dp = ep;
}
}
return mi - sc->tulip_mediainfo;
}
static const struct {
void (*vendor_identify_nic)(tulip_softc_t * const sc);
unsigned char vendor_oui[3];
} tulip_vendors[] = {
{ tulip_identify_dec_nic, { 0x08, 0x00, 0x2B } },
{ tulip_identify_dec_nic, { 0x00, 0x00, 0xF8 } },
{ tulip_identify_smc_nic, { 0x00, 0x00, 0xC0 } },
{ tulip_identify_smc_nic, { 0x00, 0xE0, 0x29 } },
{ tulip_identify_znyx_nic, { 0x00, 0xC0, 0x95 } },
{ tulip_identify_cogent_nic, { 0x00, 0x00, 0x92 } },
{ tulip_identify_asante_nic, { 0x00, 0x00, 0x94 } },
{ NULL }
};
/*
* This deals with the vagaries of the address roms and the
* brain-deadness that various vendors commit in using them.
*/
static int
tulip_read_macaddr(
tulip_softc_t * const sc)
{
unsigned cksum, rom_cksum, idx;
u_int32_t csr;
unsigned char tmpbuf[8];
static const u_char testpat[] = { 0xFF, 0, 0x55, 0xAA, 0xFF, 0, 0x55, 0xAA };
sc->tulip_connidx = TULIP_SROM_LASTCONNIDX;
if (sc->tulip_chipid == TULIP_21040) {
TULIP_CSR_WRITE(sc, csr_enetrom, 1);
for (idx = 0; idx < sizeof(sc->tulip_rombuf); idx++) {
int cnt = 0;
while (((csr = TULIP_CSR_READ(sc, csr_enetrom)) & 0x80000000L) && cnt < 10000)
cnt++;
sc->tulip_rombuf[idx] = csr & 0xFF;
}
sc->tulip_boardsw = &tulip_21040_boardsw;
#if defined(TULIP_EISA)
} else if (sc->tulip_chipid == TULIP_DE425) {
int cnt;
for (idx = 0, cnt = 0; idx < sizeof(testpat) && cnt < 32; cnt++) {
tmpbuf[idx] = TULIP_CSR_READBYTE(sc, csr_enetrom);
if (tmpbuf[idx] == testpat[idx])
++idx;
else
idx = 0;
}
for (idx = 0; idx < 32; idx++)
sc->tulip_rombuf[idx] = TULIP_CSR_READBYTE(sc, csr_enetrom);
sc->tulip_boardsw = &tulip_21040_boardsw;
#endif /* TULIP_EISA */
} else {
if (sc->tulip_chipid == TULIP_21041) {
/*
* Thankfully all 21041's act the same.
*/
sc->tulip_boardsw = &tulip_21041_boardsw;
} else {
/*
* Assume all 21140 board are compatible with the
* DEC 10/100 evaluation board. Not really valid but
* it's the best we can do until every one switches to
* the new SROM format.
*/
sc->tulip_boardsw = &tulip_21140_eb_boardsw;
}
tulip_srom_read(sc);
if (tulip_srom_crcok(sc->tulip_rombuf)) {
/*
* SROM CRC is valid therefore it must be in the
* new format.
*/
sc->tulip_features |= TULIP_HAVE_ISVSROM;
} else if (sc->tulip_rombuf[126] == 0xff && sc->tulip_rombuf[127] == 0xFF) {
/*
* No checksum is present. See if the SROM id checks out;
* the first 18 bytes should be 0 followed by a 1 followed
* by the number of adapters (which we don't deal with yet).
*/
for (idx = 0; idx < 18; idx++) {
if (sc->tulip_rombuf[idx] != 0)
break;
}
if (idx == 18 && sc->tulip_rombuf[18] == 1 && sc->tulip_rombuf[19] != 0)
sc->tulip_features |= TULIP_HAVE_ISVSROM;
}
if ((sc->tulip_features & TULIP_HAVE_ISVSROM) && tulip_srom_decode(sc)) {
if (sc->tulip_chipid != TULIP_21041)
sc->tulip_boardsw = &tulip_2114x_isv_boardsw;
/*
* If the SROM specifies more than one adapter, tag this as a
* BASE rom.
*/
if (sc->tulip_rombuf[19] > 1)
sc->tulip_features |= TULIP_HAVE_BASEROM;
if (sc->tulip_boardsw == NULL)
return -6;
goto check_oui;
}
}
if (bcmp(&sc->tulip_rombuf[0], &sc->tulip_rombuf[16], 8) != 0) {
/*
* Some folks don't use the standard ethernet rom format
* but instead just put the address in the first 6 bytes
* of the rom and let the rest be all 0xffs. (Can we say
* ZNYX???) (well sometimes they put in a checksum so we'll
* start at 8).
*/
for (idx = 8; idx < 32; idx++) {
if (sc->tulip_rombuf[idx] != 0xFF)
return -4;
}
/*
* Make sure the address is not multicast or locally assigned
* that the OUI is not 00-00-00.
*/
if ((sc->tulip_rombuf[0] & 3) != 0)
return -4;
if (sc->tulip_rombuf[0] == 0 && sc->tulip_rombuf[1] == 0
&& sc->tulip_rombuf[2] == 0)
return -4;
bcopy(sc->tulip_rombuf, sc->tulip_enaddr, 6);
sc->tulip_features |= TULIP_HAVE_OKROM;
goto check_oui;
} else {
/*
* A number of makers of multiport boards (ZNYX and Cogent)
* only put on one address ROM on their 21040 boards. So
* if the ROM is all zeros (or all 0xFFs), look at the
* previous configured boards (as long as they are on the same
* PCI bus and the bus number is non-zero) until we find the
* master board with address ROM. We then use its address ROM
* as the base for this board. (we add our relative board
* to the last byte of its address).
*/
for (idx = 0; idx < sizeof(sc->tulip_rombuf); idx++) {
if (sc->tulip_rombuf[idx] != 0 && sc->tulip_rombuf[idx] != 0xFF)
break;
}
if (idx == sizeof(sc->tulip_rombuf)) {
int root_unit;
tulip_softc_t *root_sc = NULL;
for (root_unit = sc->tulip_unit - 1; root_unit >= 0; root_unit--) {
root_sc = TULIP_UNIT_TO_SOFTC(root_unit);
if (root_sc == NULL || (root_sc->tulip_features & (TULIP_HAVE_OKROM|TULIP_HAVE_SLAVEDROM)) == TULIP_HAVE_OKROM)
break;
root_sc = NULL;
}
if (root_sc != NULL && (root_sc->tulip_features & TULIP_HAVE_BASEROM)
&& root_sc->tulip_chipid == sc->tulip_chipid
&& root_sc->tulip_pci_busno == sc->tulip_pci_busno) {
sc->tulip_features |= TULIP_HAVE_SLAVEDROM;
sc->tulip_boardsw = root_sc->tulip_boardsw;
strcpy(sc->tulip_boardid, root_sc->tulip_boardid);
if (sc->tulip_boardsw->bd_type == TULIP_21140_ISV) {
bcopy(root_sc->tulip_rombuf, sc->tulip_rombuf,
sizeof(sc->tulip_rombuf));
if (!tulip_srom_decode(sc))
return -5;
} else {
bcopy(root_sc->tulip_enaddr, sc->tulip_enaddr, 6);
sc->tulip_enaddr[5] += sc->tulip_unit - root_sc->tulip_unit;
}
/*
* Now for a truly disgusting kludge: all 4 21040s on
* the ZX314 share the same INTA line so the mapping
* setup by the BIOS on the PCI bridge is worthless.
* Rather than reprogramming the value in the config
* register, we will handle this internally.
*/
if (root_sc->tulip_features & TULIP_HAVE_SHAREDINTR) {
sc->tulip_slaves = root_sc->tulip_slaves;
root_sc->tulip_slaves = sc;
sc->tulip_features |= TULIP_HAVE_SLAVEDINTR;
}
return 0;
}
}
}
/*
* This is the standard DEC address ROM test.
*/
if (bcmp(&sc->tulip_rombuf[24], testpat, 8) != 0)
return -3;
tmpbuf[0] = sc->tulip_rombuf[15]; tmpbuf[1] = sc->tulip_rombuf[14];
tmpbuf[2] = sc->tulip_rombuf[13]; tmpbuf[3] = sc->tulip_rombuf[12];
tmpbuf[4] = sc->tulip_rombuf[11]; tmpbuf[5] = sc->tulip_rombuf[10];
tmpbuf[6] = sc->tulip_rombuf[9]; tmpbuf[7] = sc->tulip_rombuf[8];
if (bcmp(&sc->tulip_rombuf[0], tmpbuf, 8) != 0)
return -2;
bcopy(sc->tulip_rombuf, sc->tulip_enaddr, 6);
cksum = *(u_int16_t *) &sc->tulip_enaddr[0];
cksum *= 2;
if (cksum > 65535) cksum -= 65535;
cksum += *(u_int16_t *) &sc->tulip_enaddr[2];
if (cksum > 65535) cksum -= 65535;
cksum *= 2;
if (cksum > 65535) cksum -= 65535;
cksum += *(u_int16_t *) &sc->tulip_enaddr[4];
if (cksum >= 65535) cksum -= 65535;
rom_cksum = *(u_int16_t *) &sc->tulip_rombuf[6];
if (cksum != rom_cksum)
return -1;
check_oui:
/*
* Check for various boards based on OUI. Did I say braindead?
*/
for (idx = 0; tulip_vendors[idx].vendor_identify_nic != NULL; idx++) {
if (bcmp((caddr_t) sc->tulip_enaddr,
(caddr_t) tulip_vendors[idx].vendor_oui, 3) == 0) {
(*tulip_vendors[idx].vendor_identify_nic)(sc);
break;
}
}
sc->tulip_features |= TULIP_HAVE_OKROM;
return 0;
}
#if defined(IFM_ETHER)
static void
tulip_ifmedia_add(
tulip_softc_t * const sc)
{
tulip_media_t media;
int medias = 0;
for (media = TULIP_MEDIA_UNKNOWN; media < TULIP_MEDIA_MAX; media++) {
if (sc->tulip_mediums[media] != NULL) {
ifmedia_add(&sc->tulip_ifmedia, tulip_media_to_ifmedia[media],
0, 0);
medias++;
}
}
if (medias == 0) {
sc->tulip_features |= TULIP_HAVE_NOMEDIA;
ifmedia_add(&sc->tulip_ifmedia, IFM_ETHER | IFM_NONE, 0, 0);
ifmedia_set(&sc->tulip_ifmedia, IFM_ETHER | IFM_NONE);
} else if (sc->tulip_media == TULIP_MEDIA_UNKNOWN) {
ifmedia_add(&sc->tulip_ifmedia, IFM_ETHER | IFM_AUTO, 0, 0);
ifmedia_set(&sc->tulip_ifmedia, IFM_ETHER | IFM_AUTO);
} else {
ifmedia_set(&sc->tulip_ifmedia, tulip_media_to_ifmedia[sc->tulip_media]);
sc->tulip_flags |= TULIP_PRINTMEDIA;
tulip_linkup(sc, sc->tulip_media);
}
}
static int
tulip_ifmedia_change(
struct ifnet * const ifp)
{
tulip_softc_t * const sc = TULIP_IFP_TO_SOFTC(ifp);
sc->tulip_flags |= TULIP_NEEDRESET;
sc->tulip_probe_state = TULIP_PROBE_INACTIVE;
sc->tulip_media = TULIP_MEDIA_UNKNOWN;
if (IFM_SUBTYPE(sc->tulip_ifmedia.ifm_media) != IFM_AUTO) {
tulip_media_t media;
for (media = TULIP_MEDIA_UNKNOWN; media < TULIP_MEDIA_MAX; media++) {
if (sc->tulip_mediums[media] != NULL
&& sc->tulip_ifmedia.ifm_media == tulip_media_to_ifmedia[media]) {
sc->tulip_flags |= TULIP_PRINTMEDIA;
sc->tulip_flags &= ~TULIP_DIDNWAY;
tulip_linkup(sc, media);
return 0;
}
}
}
sc->tulip_flags &= ~(TULIP_TXPROBE_ACTIVE|TULIP_WANTRXACT);
tulip_reset(sc);
tulip_init(sc);
return 0;
}
/*
* Media status callback
*/
static void
tulip_ifmedia_status(
struct ifnet * const ifp,
struct ifmediareq *req)
{
tulip_softc_t *sc = TULIP_IFP_TO_SOFTC(ifp);
#if defined(__bsdi__)
if (sc->tulip_mii.mii_instance != 0) {
mii_pollstat(&sc->tulip_mii);
req->ifm_active = sc->tulip_mii.mii_media_active;
req->ifm_status = sc->tulip_mii.mii_media_status;
return;
}
#endif
if (sc->tulip_media == TULIP_MEDIA_UNKNOWN)
return;
req->ifm_status = IFM_AVALID;
if (sc->tulip_flags & TULIP_LINKUP)
req->ifm_status |= IFM_ACTIVE;
req->ifm_active = tulip_media_to_ifmedia[sc->tulip_media];
}
#endif
static void
tulip_addr_filter(
tulip_softc_t * const sc)
{
#if defined(__FreeBSD__) && __FreeBSD__ >= 3
struct ifmultiaddr *ifma;
u_char *addrp;
#else
struct ether_multistep step;
struct ether_multi *enm;
#endif
int multicnt;
sc->tulip_flags &= ~(TULIP_WANTHASHPERFECT|TULIP_WANTHASHONLY|TULIP_ALLMULTI);
sc->tulip_flags |= TULIP_WANTSETUP|TULIP_WANTTXSTART;
sc->tulip_cmdmode &= ~TULIP_CMD_RXRUN;
sc->tulip_intrmask &= ~TULIP_STS_RXSTOPPED;
#if defined(IFF_ALLMULTI)
sc->tulip_if.if_flags &= ~IFF_ALLMULTI;
#endif
#if defined(__FreeBSD__) && __FreeBSD__ >= 3
multicnt = 0;
for (ifma = sc->tulip_if.if_multiaddrs.lh_first; ifma != NULL;
ifma = ifma->ifma_link.le_next) {
if (ifma->ifma_addr->sa_family == AF_LINK)
multicnt++;
}
#else
multicnt = sc->tulip_multicnt;
#endif
sc->tulip_if.if_start = tulip_ifstart; /* so the setup packet gets queued */
if (multicnt > 14) {
u_int32_t *sp = sc->tulip_setupdata;
unsigned hash;
/*
* Some early passes of the 21140 have broken implementations of
* hash-perfect mode. When we get too many multicasts for perfect
* filtering with these chips, we need to switch into hash-only
* mode (this is better than all-multicast on network with lots
* of multicast traffic).
*/
if (sc->tulip_features & TULIP_HAVE_BROKEN_HASH)
sc->tulip_flags |= TULIP_WANTHASHONLY;
else
sc->tulip_flags |= TULIP_WANTHASHPERFECT;
/*
* If we have more than 14 multicasts, we have
* go into hash perfect mode (512 bit multicast
* hash and one perfect hardware).
*/
bzero(sc->tulip_setupdata, sizeof(sc->tulip_setupdata));
#if defined(__FreeBSD__) && __FreeBSD__ >= 3
for (ifma = sc->tulip_if.if_multiaddrs.lh_first; ifma != NULL;
ifma = ifma->ifma_link.le_next) {
if (ifma->ifma_addr->sa_family != AF_LINK)
continue;
hash = tulip_mchash(LLADDR((struct sockaddr_dl *)ifma->ifma_addr));
sp[hash >> 4] |= 1 << (hash & 0xF);
}
#else
ETHER_FIRST_MULTI(step, TULIP_ETHERCOM(sc), enm);
while (enm != NULL) {
if (bcmp(enm->enm_addrlo, enm->enm_addrhi, 6) == 0) {
hash = tulip_mchash(enm->enm_addrlo);
sp[hash >> 4] |= 1 << (hash & 0xF);
} else {
sc->tulip_flags |= TULIP_ALLMULTI;
sc->tulip_flags &= ~(TULIP_WANTHASHONLY|TULIP_WANTHASHPERFECT);
break;
}
ETHER_NEXT_MULTI(step, enm);
}
#endif
/*
* No reason to use a hash if we are going to be
* receiving every multicast.
*/
if ((sc->tulip_flags & TULIP_ALLMULTI) == 0) {
hash = tulip_mchash(etherbroadcastaddr);
sp[hash >> 4] |= 1 << (hash & 0xF);
if (sc->tulip_flags & TULIP_WANTHASHONLY) {
hash = tulip_mchash(sc->tulip_enaddr);
sp[hash >> 4] |= 1 << (hash & 0xF);
} else {
sp[39] = ((u_int16_t *) sc->tulip_enaddr)[0];
sp[40] = ((u_int16_t *) sc->tulip_enaddr)[1];
sp[41] = ((u_int16_t *) sc->tulip_enaddr)[2];
}
}
}
if ((sc->tulip_flags & (TULIP_WANTHASHPERFECT|TULIP_WANTHASHONLY)) == 0) {
u_int32_t *sp = sc->tulip_setupdata;
int idx = 0;
if ((sc->tulip_flags & TULIP_ALLMULTI) == 0) {
/*
* Else can get perfect filtering for 16 addresses.
*/
#if defined(__FreeBSD__) && __FreeBSD__ >= 3
for (ifma = sc->tulip_if.if_multiaddrs.lh_first; ifma != NULL;
ifma = ifma->ifma_link.le_next) {
if (ifma->ifma_addr->sa_family != AF_LINK)
continue;
addrp = LLADDR((struct sockaddr_dl *)ifma->ifma_addr);
*sp++ = ((u_int16_t *) addrp)[0];
*sp++ = ((u_int16_t *) addrp)[1];
*sp++ = ((u_int16_t *) addrp)[2];
idx++;
}
#else
ETHER_FIRST_MULTI(step, TULIP_ETHERCOM(sc), enm);
for (; enm != NULL; idx++) {
if (bcmp(enm->enm_addrlo, enm->enm_addrhi, 6) == 0) {
*sp++ = ((u_int16_t *) enm->enm_addrlo)[0];
*sp++ = ((u_int16_t *) enm->enm_addrlo)[1];
*sp++ = ((u_int16_t *) enm->enm_addrlo)[2];
} else {
sc->tulip_flags |= TULIP_ALLMULTI;
break;
}
ETHER_NEXT_MULTI(step, enm);
}
#endif
/*
* Add the broadcast address.
*/
idx++;
*sp++ = 0xFFFF;
*sp++ = 0xFFFF;
*sp++ = 0xFFFF;
}
/*
* Pad the rest with our hardware address
*/
for (; idx < 16; idx++) {
*sp++ = ((u_int16_t *) sc->tulip_enaddr)[0];
*sp++ = ((u_int16_t *) sc->tulip_enaddr)[1];
*sp++ = ((u_int16_t *) sc->tulip_enaddr)[2];
}
}
#if defined(IFF_ALLMULTI)
if (sc->tulip_flags & TULIP_ALLMULTI)
sc->tulip_if.if_flags |= IFF_ALLMULTI;
#endif
}
static void
tulip_reset(
tulip_softc_t * const sc)
{
tulip_ringinfo_t *ri;
tulip_desc_t *di;
u_int32_t inreset = (sc->tulip_flags & TULIP_INRESET);
/*
* Brilliant. Simply brilliant. When switching modes/speeds
* on a 2114*, you need to set the appriopriate MII/PCS/SCL/PS
* bits in CSR6 and then do a software reset to get the 21140
* to properly reset its internal pathways to the right places.
* Grrrr.
*/
if (sc->tulip_boardsw->bd_media_preset != NULL)
(*sc->tulip_boardsw->bd_media_preset)(sc);
TULIP_CSR_WRITE(sc, csr_busmode, TULIP_BUSMODE_SWRESET);
DELAY(10); /* Wait 10 microseconds (actually 50 PCI cycles but at
33MHz that comes to two microseconds but wait a
bit longer anyways) */
if (!inreset) {
sc->tulip_flags |= TULIP_INRESET;
sc->tulip_flags &= ~(TULIP_NEEDRESET|TULIP_RXBUFSLOW);
sc->tulip_if.if_flags &= ~IFF_OACTIVE;
}
TULIP_CSR_WRITE(sc, csr_txlist, TULIP_KVATOPHYS(sc, &sc->tulip_txinfo.ri_first[0]));
TULIP_CSR_WRITE(sc, csr_rxlist, TULIP_KVATOPHYS(sc, &sc->tulip_rxinfo.ri_first[0]));
TULIP_CSR_WRITE(sc, csr_busmode,
(1 << (TULIP_BURSTSIZE(sc->tulip_unit) + 8))
|TULIP_BUSMODE_CACHE_ALIGN8
|TULIP_BUSMODE_READMULTIPLE
|(BYTE_ORDER != LITTLE_ENDIAN ? TULIP_BUSMODE_BIGENDIAN : 0));
sc->tulip_txtimer = 0;
sc->tulip_txq.ifq_maxlen = TULIP_TXDESCS;
/*
* Free all the mbufs that were on the transmit ring.
*/
for (;;) {
struct mbuf *m;
IF_DEQUEUE(&sc->tulip_txq, m);
if (m == NULL)
break;
m_freem(m);
}
ri = &sc->tulip_txinfo;
ri->ri_nextin = ri->ri_nextout = ri->ri_first;
ri->ri_free = ri->ri_max;
for (di = ri->ri_first; di < ri->ri_last; di++)
di->d_status = 0;
/*
* We need to collect all the mbufs were on the
* receive ring before we reinit it either to put
* them back on or to know if we have to allocate
* more.
*/
ri = &sc->tulip_rxinfo;
ri->ri_nextin = ri->ri_nextout = ri->ri_first;
ri->ri_free = ri->ri_max;
for (di = ri->ri_first; di < ri->ri_last; di++) {
di->d_status = 0;
di->d_length1 = 0; di->d_addr1 = 0;
di->d_length2 = 0; di->d_addr2 = 0;
}
for (;;) {
struct mbuf *m;
IF_DEQUEUE(&sc->tulip_rxq, m);
if (m == NULL)
break;
m_freem(m);
}
/*
* If tulip_reset is being called recurisvely, exit quickly knowing
* that when the outer tulip_reset returns all the right stuff will
* have happened.
*/
if (inreset)
return;
sc->tulip_intrmask |= TULIP_STS_NORMALINTR|TULIP_STS_RXINTR|TULIP_STS_TXINTR
|TULIP_STS_ABNRMLINTR|TULIP_STS_SYSERROR|TULIP_STS_TXSTOPPED
|TULIP_STS_TXUNDERFLOW|TULIP_STS_TXBABBLE|TULIP_STS_LINKFAIL
|TULIP_STS_RXSTOPPED;
if ((sc->tulip_flags & TULIP_DEVICEPROBE) == 0)
(*sc->tulip_boardsw->bd_media_select)(sc);
#if defined(TULIP_DEBUG)
if ((sc->tulip_flags & TULIP_NEEDRESET) == TULIP_NEEDRESET)
printf(TULIP_PRINTF_FMT ": tulip_reset: additional reset needed?!?\n",
TULIP_PRINTF_ARGS);
#endif
tulip_media_print(sc);
if (sc->tulip_features & TULIP_HAVE_DUALSENSE)
TULIP_CSR_WRITE(sc, csr_sia_status, TULIP_CSR_READ(sc, csr_sia_status));
sc->tulip_flags &= ~(TULIP_DOINGSETUP|TULIP_WANTSETUP|TULIP_INRESET
|TULIP_RXACT);
tulip_addr_filter(sc);
}
static void
tulip_init(
tulip_softc_t * const sc)
{
if (sc->tulip_if.if_flags & IFF_UP) {
if ((sc->tulip_if.if_flags & IFF_RUNNING) == 0) {
/* initialize the media */
tulip_reset(sc);
}
sc->tulip_if.if_flags |= IFF_RUNNING;
if (sc->tulip_if.if_flags & IFF_PROMISC) {
sc->tulip_flags |= TULIP_PROMISC;
sc->tulip_cmdmode |= TULIP_CMD_PROMISCUOUS;
sc->tulip_intrmask |= TULIP_STS_TXINTR;
} else {
sc->tulip_flags &= ~TULIP_PROMISC;
sc->tulip_cmdmode &= ~TULIP_CMD_PROMISCUOUS;
if (sc->tulip_flags & TULIP_ALLMULTI) {
sc->tulip_cmdmode |= TULIP_CMD_ALLMULTI;
} else {
sc->tulip_cmdmode &= ~TULIP_CMD_ALLMULTI;
}
}
sc->tulip_cmdmode |= TULIP_CMD_TXRUN;
if ((sc->tulip_flags & (TULIP_TXPROBE_ACTIVE|TULIP_WANTSETUP)) == 0) {
tulip_rx_intr(sc);
sc->tulip_cmdmode |= TULIP_CMD_RXRUN;
sc->tulip_intrmask |= TULIP_STS_RXSTOPPED;
} else {
sc->tulip_if.if_flags |= IFF_OACTIVE;
sc->tulip_cmdmode &= ~TULIP_CMD_RXRUN;
sc->tulip_intrmask &= ~TULIP_STS_RXSTOPPED;
}
TULIP_CSR_WRITE(sc, csr_intr, sc->tulip_intrmask);
TULIP_CSR_WRITE(sc, csr_command, sc->tulip_cmdmode);
if ((sc->tulip_flags & (TULIP_WANTSETUP|TULIP_TXPROBE_ACTIVE)) == TULIP_WANTSETUP)
tulip_txput_setup(sc);
} else {
sc->tulip_if.if_flags &= ~IFF_RUNNING;
tulip_reset(sc);
}
}
static void
tulip_rx_intr(
tulip_softc_t * const sc)
{
TULIP_PERFSTART(rxintr)
tulip_ringinfo_t * const ri = &sc->tulip_rxinfo;
struct ifnet * const ifp = &sc->tulip_if;
int fillok = 1;
#if defined(TULIP_DEBUG)
int cnt = 0;
#endif
for (;;) {
TULIP_PERFSTART(rxget)
struct ether_header eh;
tulip_desc_t *eop = ri->ri_nextin;
int total_len = 0, last_offset = 0;
struct mbuf *ms = NULL, *me = NULL;
int accept = 0;
if (fillok && sc->tulip_rxq.ifq_len < TULIP_RXQ_TARGET)
goto queue_mbuf;
#if defined(TULIP_DEBUG)
if (cnt == ri->ri_max)
break;
#endif
/*
* If the TULIP has no descriptors, there can't be any receive
* descriptors to process.
*/
if (eop == ri->ri_nextout)
break;
/*
* 90% of the packets will fit in one descriptor. So we optimize
* for that case.
*/
if ((((volatile tulip_desc_t *) eop)->d_status & (TULIP_DSTS_OWNER|TULIP_DSTS_RxFIRSTDESC|TULIP_DSTS_RxLASTDESC)) == (TULIP_DSTS_RxFIRSTDESC|TULIP_DSTS_RxLASTDESC)) {
IF_DEQUEUE(&sc->tulip_rxq, ms);
me = ms;
} else {
/*
* If still owned by the TULIP, don't touch it.
*/
if (((volatile tulip_desc_t *) eop)->d_status & TULIP_DSTS_OWNER)
break;
/*
* It is possible (though improbable unless the BIG_PACKET support
* is enabled or MCLBYTES < 1518) for a received packet to cross
* more than one receive descriptor.
*/
while ((((volatile tulip_desc_t *) eop)->d_status & TULIP_DSTS_RxLASTDESC) == 0) {
if (++eop == ri->ri_last)
eop = ri->ri_first;
if (eop == ri->ri_nextout || ((((volatile tulip_desc_t *) eop)->d_status & TULIP_DSTS_OWNER))) {
#if defined(TULIP_DEBUG)
sc->tulip_dbg.dbg_rxintrs++;
sc->tulip_dbg.dbg_rxpktsperintr[cnt]++;
#endif
TULIP_PERFEND(rxget);
TULIP_PERFEND(rxintr);
return;
}
total_len++;
}
/*
* Dequeue the first buffer for the start of the packet. Hopefully
* this will be the only one we need to dequeue. However, if the
* packet consumed multiple descriptors, then we need to dequeue
* those buffers and chain to the starting mbuf. All buffers but
* the last buffer have the same length so we can set that now.
* (we add to last_offset instead of multiplying since we normally
* won't go into the loop and thereby saving a ourselves from
* doing a multiplication by 0 in the normal case).
*/
IF_DEQUEUE(&sc->tulip_rxq, ms);
for (me = ms; total_len > 0; total_len--) {
me->m_len = TULIP_RX_BUFLEN;
last_offset += TULIP_RX_BUFLEN;
IF_DEQUEUE(&sc->tulip_rxq, me->m_next);
me = me->m_next;
}
}
/*
* Now get the size of received packet (minus the CRC).
*/
total_len = ((eop->d_status >> 16) & 0x7FFF) - 4;
if ((sc->tulip_flags & TULIP_RXIGNORE) == 0
&& ((eop->d_status & TULIP_DSTS_ERRSUM) == 0
#ifdef BIG_PACKET
|| (total_len <= sc->tulip_if.if_mtu + sizeof(struct ether_header) &&
(eop->d_status & (TULIP_DSTS_RxBADLENGTH|TULIP_DSTS_RxRUNT|
TULIP_DSTS_RxCOLLSEEN|TULIP_DSTS_RxBADCRC|
TULIP_DSTS_RxOVERFLOW)) == 0)
#endif
)) {
me->m_len = total_len - last_offset;
eh = *mtod(ms, struct ether_header *);
#if NBPFILTER > 0
if (sc->tulip_bpf != NULL)
if (me == ms)
TULIP_BPF_TAP(sc, mtod(ms, caddr_t), total_len);
else
TULIP_BPF_MTAP(sc, ms);
#endif
sc->tulip_flags |= TULIP_RXACT;
if ((sc->tulip_flags & (TULIP_PROMISC|TULIP_HASHONLY))
&& (eh.ether_dhost[0] & 1) == 0
&& !TULIP_ADDREQUAL(eh.ether_dhost, sc->tulip_enaddr))
goto next;
accept = 1;
total_len -= sizeof(struct ether_header);
} else {
ifp->if_ierrors++;
if (eop->d_status & (TULIP_DSTS_RxBADLENGTH|TULIP_DSTS_RxOVERFLOW|TULIP_DSTS_RxWATCHDOG)) {
sc->tulip_dot3stats.dot3StatsInternalMacReceiveErrors++;
} else {
const char *error = NULL;
if (eop->d_status & TULIP_DSTS_RxTOOLONG) {
sc->tulip_dot3stats.dot3StatsFrameTooLongs++;
error = "frame too long";
}
if (eop->d_status & TULIP_DSTS_RxBADCRC) {
if (eop->d_status & TULIP_DSTS_RxDRBBLBIT) {
sc->tulip_dot3stats.dot3StatsAlignmentErrors++;
error = "alignment error";
} else {
sc->tulip_dot3stats.dot3StatsFCSErrors++;
error = "bad crc";
}
}
if (error != NULL && (sc->tulip_flags & TULIP_NOMESSAGES) == 0) {
printf(TULIP_PRINTF_FMT ": receive: " TULIP_EADDR_FMT ": %s\n",
TULIP_PRINTF_ARGS,
TULIP_EADDR_ARGS(mtod(ms, u_char *) + 6),
error);
sc->tulip_flags |= TULIP_NOMESSAGES;
}
}
}
next:
#if defined(TULIP_DEBUG)
cnt++;
#endif
ifp->if_ipackets++;
if (++eop == ri->ri_last)
eop = ri->ri_first;
ri->ri_nextin = eop;
queue_mbuf:
/*
* Either we are priming the TULIP with mbufs (m == NULL)
* or we are about to accept an mbuf for the upper layers
* so we need to allocate an mbuf to replace it. If we
* can't replace it, send up it anyways. This may cause
* us to drop packets in the future but that's better than
* being caught in livelock.
*
* Note that if this packet crossed multiple descriptors
* we don't even try to reallocate all the mbufs here.
* Instead we rely on the test of the beginning of
* the loop to refill for the extra consumed mbufs.
*/
if (accept || ms == NULL) {
struct mbuf *m0;
MGETHDR(m0, M_DONTWAIT, MT_DATA);
if (m0 != NULL) {
#if defined(TULIP_COPY_RXDATA)
if (!accept || total_len >= MHLEN) {
#endif
MCLGET(m0, M_DONTWAIT);
if ((m0->m_flags & M_EXT) == 0) {
m_freem(m0);
m0 = NULL;
}
#if defined(TULIP_COPY_RXDATA)
}
#endif
}
if (accept
#if defined(TULIP_COPY_RXDATA)
&& m0 != NULL
#endif
) {
#if defined(__bsdi__)
eh.ether_type = ntohs(eh.ether_type);
#endif
#if !defined(TULIP_COPY_RXDATA)
ms->m_data += sizeof(struct ether_header);
ms->m_len -= sizeof(struct ether_header);
ms->m_pkthdr.len = total_len;
ms->m_pkthdr.rcvif = ifp;
ether_input(ifp, &eh, ms);
#else
#ifdef BIG_PACKET
#error BIG_PACKET is incompatible with TULIP_COPY_RXDATA
#endif
if (ms == me)
bcopy(mtod(ms, caddr_t) + sizeof(struct ether_header),
mtod(m0, caddr_t), total_len);
else
m_copydata(ms, 0, total_len, mtod(m0, caddr_t));
m0->m_len = m0->m_pkthdr.len = total_len;
m0->m_pkthdr.rcvif = ifp;
ether_input(ifp, &eh, m0);
m0 = ms;
#endif
}
ms = m0;
}
if (ms == NULL) {
/*
* Couldn't allocate a new buffer. Don't bother
* trying to replenish the receive queue.
*/
fillok = 0;
sc->tulip_flags |= TULIP_RXBUFSLOW;
#if defined(TULIP_DEBUG)
sc->tulip_dbg.dbg_rxlowbufs++;
#endif
TULIP_PERFEND(rxget);
continue;
}
/*
* Now give the buffer(s) to the TULIP and save in our
* receive queue.
*/
do {
ri->ri_nextout->d_length1 = TULIP_RX_BUFLEN;
ri->ri_nextout->d_addr1 = TULIP_KVATOPHYS(sc, mtod(ms, caddr_t));
ri->ri_nextout->d_status = TULIP_DSTS_OWNER;
if (++ri->ri_nextout == ri->ri_last)
ri->ri_nextout = ri->ri_first;
me = ms->m_next;
ms->m_next = NULL;
IF_ENQUEUE(&sc->tulip_rxq, ms);
} while ((ms = me) != NULL);
if (sc->tulip_rxq.ifq_len >= TULIP_RXQ_TARGET)
sc->tulip_flags &= ~TULIP_RXBUFSLOW;
TULIP_PERFEND(rxget);
}
#if defined(TULIP_DEBUG)
sc->tulip_dbg.dbg_rxintrs++;
sc->tulip_dbg.dbg_rxpktsperintr[cnt]++;
#endif
TULIP_PERFEND(rxintr);
}
static int
tulip_tx_intr(
tulip_softc_t * const sc)
{
TULIP_PERFSTART(txintr)
tulip_ringinfo_t * const ri = &sc->tulip_txinfo;
struct mbuf *m;
int xmits = 0;
int descs = 0;
while (ri->ri_free < ri->ri_max) {
u_int32_t d_flag;
if (((volatile tulip_desc_t *) ri->ri_nextin)->d_status & TULIP_DSTS_OWNER)
break;
d_flag = ri->ri_nextin->d_flag;
if (d_flag & TULIP_DFLAG_TxLASTSEG) {
if (d_flag & TULIP_DFLAG_TxSETUPPKT) {
/*
* We've just finished processing a setup packet.
* Mark that we finished it. If there's not
* another pending, startup the TULIP receiver.
* Make sure we ack the RXSTOPPED so we won't get
* an abormal interrupt indication.
*/
sc->tulip_flags &= ~(TULIP_DOINGSETUP|TULIP_HASHONLY);
if (ri->ri_nextin->d_flag & TULIP_DFLAG_TxINVRSFILT)
sc->tulip_flags |= TULIP_HASHONLY;
if ((sc->tulip_flags & (TULIP_WANTSETUP|TULIP_TXPROBE_ACTIVE)) == 0) {
tulip_rx_intr(sc);
sc->tulip_cmdmode |= TULIP_CMD_RXRUN;
sc->tulip_intrmask |= TULIP_STS_RXSTOPPED;
TULIP_CSR_WRITE(sc, csr_status, TULIP_STS_RXSTOPPED);
TULIP_CSR_WRITE(sc, csr_intr, sc->tulip_intrmask);
TULIP_CSR_WRITE(sc, csr_command, sc->tulip_cmdmode);
}
} else {
const u_int32_t d_status = ri->ri_nextin->d_status;
IF_DEQUEUE(&sc->tulip_txq, m);
#if NBPFILTER > 0
if (sc->tulip_bpf != NULL)
TULIP_BPF_MTAP(sc, m);
#endif
m_freem(m);
if (sc->tulip_flags & TULIP_TXPROBE_ACTIVE) {
tulip_mediapoll_event_t event = TULIP_MEDIAPOLL_TXPROBE_OK;
if (d_status & (TULIP_DSTS_TxNOCARR|TULIP_DSTS_TxEXCCOLL)) {
#if defined(TULIP_DEBUG)
if (d_status & TULIP_DSTS_TxNOCARR)
sc->tulip_dbg.dbg_txprobe_nocarr++;
if (d_status & TULIP_DSTS_TxEXCCOLL)
sc->tulip_dbg.dbg_txprobe_exccoll++;
#endif
event = TULIP_MEDIAPOLL_TXPROBE_FAILED;
}
(*sc->tulip_boardsw->bd_media_poll)(sc, event);
/*
* Escape from the loop before media poll has reset the TULIP!
*/
break;
} else {
xmits++;
if (d_status & TULIP_DSTS_ERRSUM) {
sc->tulip_if.if_oerrors++;
if (d_status & TULIP_DSTS_TxEXCCOLL)
sc->tulip_dot3stats.dot3StatsExcessiveCollisions++;
if (d_status & TULIP_DSTS_TxLATECOLL)
sc->tulip_dot3stats.dot3StatsLateCollisions++;
if (d_status & (TULIP_DSTS_TxNOCARR|TULIP_DSTS_TxCARRLOSS))
sc->tulip_dot3stats.dot3StatsCarrierSenseErrors++;
if (d_status & (TULIP_DSTS_TxUNDERFLOW|TULIP_DSTS_TxBABBLE))
sc->tulip_dot3stats.dot3StatsInternalMacTransmitErrors++;
if (d_status & TULIP_DSTS_TxUNDERFLOW)
sc->tulip_dot3stats.dot3StatsInternalTransmitUnderflows++;
if (d_status & TULIP_DSTS_TxBABBLE)
sc->tulip_dot3stats.dot3StatsInternalTransmitBabbles++;
} else {
u_int32_t collisions =
(d_status & TULIP_DSTS_TxCOLLMASK)
>> TULIP_DSTS_V_TxCOLLCNT;
sc->tulip_if.if_collisions += collisions;
if (collisions == 1)
sc->tulip_dot3stats.dot3StatsSingleCollisionFrames++;
else if (collisions > 1)
sc->tulip_dot3stats.dot3StatsMultipleCollisionFrames++;
else if (d_status & TULIP_DSTS_TxDEFERRED)
sc->tulip_dot3stats.dot3StatsDeferredTransmissions++;
/*
* SQE is only valid for 10baseT/BNC/AUI when not
* running in full-duplex. In order to speed up the
* test, the corresponding bit in tulip_flags needs to
* set as well to get us to count SQE Test Errors.
*/
if (d_status & TULIP_DSTS_TxNOHRTBT & sc->tulip_flags)
sc->tulip_dot3stats.dot3StatsSQETestErrors++;
}
}
}
}
if (++ri->ri_nextin == ri->ri_last)
ri->ri_nextin = ri->ri_first;
ri->ri_free++;
descs++;
if ((sc->tulip_flags & TULIP_TXPROBE_ACTIVE) == 0)
sc->tulip_if.if_flags &= ~IFF_OACTIVE;
}
/*
* If nothing left to transmit, disable the timer.
* Else if progress, reset the timer back to 2 ticks.
*/
if (ri->ri_free == ri->ri_max || (sc->tulip_flags & TULIP_TXPROBE_ACTIVE))
sc->tulip_txtimer = 0;
else if (xmits > 0)
sc->tulip_txtimer = TULIP_TXTIMER;
sc->tulip_if.if_opackets += xmits;
TULIP_PERFEND(txintr);
return descs;
}
static void
tulip_print_abnormal_interrupt(
tulip_softc_t * const sc,
u_int32_t csr)
{
const char * const *msgp = tulip_status_bits;
const char *sep;
u_int32_t mask;
const char thrsh[] = "72|128\0\0\096|256\0\0\0128|512\0\0160|1024\0";
csr &= (1 << (sizeof(tulip_status_bits)/sizeof(tulip_status_bits[0]))) - 1;
printf(TULIP_PRINTF_FMT ": abnormal interrupt:", TULIP_PRINTF_ARGS);
for (sep = " ", mask = 1; mask <= csr; mask <<= 1, msgp++) {
if ((csr & mask) && *msgp != NULL) {
printf("%s%s", sep, *msgp);
if (mask == TULIP_STS_TXUNDERFLOW && (sc->tulip_flags & TULIP_NEWTXTHRESH)) {
sc->tulip_flags &= ~TULIP_NEWTXTHRESH;
if (sc->tulip_cmdmode & TULIP_CMD_STOREFWD) {
printf(" (switching to store-and-forward mode)");
} else {
printf(" (raising TX threshold to %s)",
&thrsh[9 * ((sc->tulip_cmdmode & TULIP_CMD_THRESHOLDCTL) >> 14)]);
}
}
sep = ", ";
}
}
printf("\n");
}
static void
tulip_intr_handler(
tulip_softc_t * const sc,
int *progress_p)
{
TULIP_PERFSTART(intr)
u_int32_t csr;
while ((csr = TULIP_CSR_READ(sc, csr_status)) & sc->tulip_intrmask) {
*progress_p = 1;
TULIP_CSR_WRITE(sc, csr_status, csr);
if (csr & TULIP_STS_SYSERROR) {
sc->tulip_last_system_error = (csr & TULIP_STS_ERRORMASK) >> TULIP_STS_ERR_SHIFT;
if (sc->tulip_flags & TULIP_NOMESSAGES) {
sc->tulip_flags |= TULIP_SYSTEMERROR;
} else {
printf(TULIP_PRINTF_FMT ": system error: %s\n",
TULIP_PRINTF_ARGS,
tulip_system_errors[sc->tulip_last_system_error]);
}
sc->tulip_flags |= TULIP_NEEDRESET;
sc->tulip_system_errors++;
break;
}
if (csr & (TULIP_STS_LINKPASS|TULIP_STS_LINKFAIL)) {
#if defined(TULIP_DEBUG)
sc->tulip_dbg.dbg_link_intrs++;
#endif
if (sc->tulip_boardsw->bd_media_poll != NULL) {
(*sc->tulip_boardsw->bd_media_poll)(sc, csr & TULIP_STS_LINKFAIL
? TULIP_MEDIAPOLL_LINKFAIL
: TULIP_MEDIAPOLL_LINKPASS);
csr &= ~TULIP_STS_ABNRMLINTR;
}
tulip_media_print(sc);
}
if (csr & (TULIP_STS_RXINTR|TULIP_STS_RXNOBUF)) {
u_int32_t misses = TULIP_CSR_READ(sc, csr_missed_frames);
if (csr & TULIP_STS_RXNOBUF)
sc->tulip_dot3stats.dot3StatsMissedFrames += misses & 0xFFFF;
/*
* Pass 2.[012] of the 21140A-A[CDE] may hang and/or corrupt data
* on receive overflows.
*/
if ((misses & 0x0FFE0000) && (sc->tulip_features & TULIP_HAVE_RXBADOVRFLW)) {
sc->tulip_dot3stats.dot3StatsInternalMacReceiveErrors++;
/*
* Stop the receiver process and spin until it's stopped.
* Tell rx_intr to drop the packets it dequeues.
*/
TULIP_CSR_WRITE(sc, csr_command, sc->tulip_cmdmode & ~TULIP_CMD_RXRUN);
while ((TULIP_CSR_READ(sc, csr_status) & TULIP_STS_RXSTOPPED) == 0)
;
TULIP_CSR_WRITE(sc, csr_status, TULIP_STS_RXSTOPPED);
sc->tulip_flags |= TULIP_RXIGNORE;
}
tulip_rx_intr(sc);
if (sc->tulip_flags & TULIP_RXIGNORE) {
/*
* Restart the receiver.
*/
sc->tulip_flags &= ~TULIP_RXIGNORE;
TULIP_CSR_WRITE(sc, csr_command, sc->tulip_cmdmode);
}
}
if (csr & TULIP_STS_ABNRMLINTR) {
u_int32_t tmp = csr & sc->tulip_intrmask
& ~(TULIP_STS_NORMALINTR|TULIP_STS_ABNRMLINTR);
if (csr & TULIP_STS_TXUNDERFLOW) {
if ((sc->tulip_cmdmode & TULIP_CMD_THRESHOLDCTL) != TULIP_CMD_THRSHLD160) {
sc->tulip_cmdmode += TULIP_CMD_THRSHLD96;
sc->tulip_flags |= TULIP_NEWTXTHRESH;
} else if (sc->tulip_features & TULIP_HAVE_STOREFWD) {
sc->tulip_cmdmode |= TULIP_CMD_STOREFWD;
sc->tulip_flags |= TULIP_NEWTXTHRESH;
}
}
if (sc->tulip_flags & TULIP_NOMESSAGES) {
sc->tulip_statusbits |= tmp;
} else {
tulip_print_abnormal_interrupt(sc, tmp);
sc->tulip_flags |= TULIP_NOMESSAGES;
}
TULIP_CSR_WRITE(sc, csr_command, sc->tulip_cmdmode);
}
if (sc->tulip_flags & (TULIP_WANTTXSTART|TULIP_TXPROBE_ACTIVE|TULIP_DOINGSETUP|TULIP_PROMISC)) {
tulip_tx_intr(sc);
if ((sc->tulip_flags & TULIP_TXPROBE_ACTIVE) == 0)
tulip_ifstart(&sc->tulip_if);
}
}
if (sc->tulip_flags & TULIP_NEEDRESET) {
tulip_reset(sc);
tulip_init(sc);
}
TULIP_PERFEND(intr);
}
#if defined(TULIP_USE_SOFTINTR)
/*
* This is a experimental idea to alleviate problems due to interrupt
* livelock. What is interrupt livelock? It's when you spend all your
* time servicing device interrupts and never drop below device ipl
* to do "useful" work.
*
* So what we do here is see if the device needs service and if so,
* disable interrupts (dismiss the interrupt), place it in a list of devices
* needing service, and issue a network software interrupt.
*
* When our network software interrupt routine gets called, we simply
* walk done the list of devices that we have created and deal with them
* at splnet/splsoftnet.
*
*/
static void
tulip_hardintr_handler(
tulip_softc_t * const sc,
int *progress_p)
{
if (TULIP_CSR_READ(sc, csr_status) & (TULIP_STS_NORMALINTR|TULIP_STS_ABNRMLINTR) == 0)
return;
*progress_p = 1;
/*
* disable interrupts
*/
TULIP_CSR_WRITE(sc, csr_intr, 0);
/*
* mark it as needing a software interrupt
*/
tulip_softintr_mask |= (1U << sc->tulip_unit);
}
static void
tulip_softintr(
void)
{
u_int32_t softintr_mask, mask;
int progress = 0;
int unit;
tulip_spl_t s;
/*
* Copy mask to local copy and reset global one to 0.
*/
s = TULIP_RAISESPL();
softintr_mask = tulip_softintr_mask;
tulip_softintr_mask = 0;
TULIP_RESTORESPL(s);
/*
* Optimize for the single unit case.
*/
if (tulip_softintr_max_unit == 0) {
if (softintr_mask & 1) {
tulip_softc_t * const sc = TULIP_UNIT_TO_SOFTC(0);
/*
* Handle the "interrupt" and then reenable interrupts
*/
softintr_mask = 0;
tulip_intr_handler(sc, &progress);
TULIP_CSR_WRITE(sc, csr_intr, sc->tulip_intrmask);
}
return;
}
/*
* Handle all "queued" interrupts in a round robin fashion.
* This is done so as not to favor a particular interface.
*/
unit = tulip_softintr_last_unit;
mask = (1U << unit);
while (softintr_mask != 0) {
if (tulip_softintr_max_unit == unit) {
unit = 0; mask = 1;
} else {
unit += 1; mask <<= 1;
}
if (softintr_mask & mask) {
tulip_softc_t * const sc = TULIP_UNIT_TO_SOFTC(unit);
/*
* Handle the "interrupt" and then reenable interrupts
*/
softintr_mask ^= mask;
tulip_intr_handler(sc, &progress);
TULIP_CSR_WRITE(sc, csr_intr, sc->tulip_intrmask);
}
}
/*
* Save where we ending up.
*/
tulip_softintr_last_unit = unit;
}
#endif /* TULIP_USE_SOFTINTR */
static tulip_intrfunc_t
tulip_intr_shared(
void *arg)
{
tulip_softc_t * sc;
int progress = 0;
for (sc = (tulip_softc_t *) arg; sc != NULL; sc = sc->tulip_slaves) {
#if defined(TULIP_DEBUG)
sc->tulip_dbg.dbg_intrs++;
#endif
#if defined(TULIP_USE_SOFTINTR)
tulip_hardintr_handler(sc, &progress);
#else
tulip_intr_handler(sc, &progress);
#endif
}
#if defined(TULIP_USE_SOFTINTR)
if (progress)
schednetisr(NETISR_DE);
#endif
#if !defined(TULIP_VOID_INTRFUNC)
return progress;
#endif
}
static tulip_intrfunc_t
tulip_intr_normal(
void *arg)
{
tulip_softc_t * sc = (tulip_softc_t *) arg;
int progress = 0;
#if defined(TULIP_DEBUG)
sc->tulip_dbg.dbg_intrs++;
#endif
#if defined(TULIP_USE_SOFTINTR)
tulip_hardintr_handler(sc, &progress);
if (progress)
schednetisr(NETISR_DE);
#else
tulip_intr_handler(sc, &progress);
#endif
#if !defined(TULIP_VOID_INTRFUNC)
return progress;
#endif
}
static struct mbuf *
tulip_mbuf_compress(
struct mbuf *m)
{
struct mbuf *m0;
#if MCLBYTES >= ETHERMTU + 18 && !defined(BIG_PACKET)
MGETHDR(m0, M_DONTWAIT, MT_DATA);
if (m0 != NULL) {
if (m->m_pkthdr.len > MHLEN) {
MCLGET(m0, M_DONTWAIT);
if ((m0->m_flags & M_EXT) == 0) {
m_freem(m);
m_freem(m0);
return NULL;
}
}
m_copydata(m, 0, m->m_pkthdr.len, mtod(m0, caddr_t));
m0->m_pkthdr.len = m0->m_len = m->m_pkthdr.len;
}
#else
int mlen = MHLEN;
int len = m->m_pkthdr.len;
struct mbuf **mp = &m0;
while (len > 0) {
if (mlen == MHLEN) {
MGETHDR(*mp, M_DONTWAIT, MT_DATA);
} else {
MGET(*mp, M_DONTWAIT, MT_DATA);
}
if (*mp == NULL) {
m_freem(m0);
m0 = NULL;
break;
}
if (len > MLEN) {
MCLGET(*mp, M_DONTWAIT);
if (((*mp)->m_flags & M_EXT) == 0) {
m_freem(m0);
m0 = NULL;
break;
}
(*mp)->m_len = len <= MCLBYTES ? len : MCLBYTES;
} else {
(*mp)->m_len = len <= mlen ? len : mlen;
}
m_copydata(m, m->m_pkthdr.len - len,
(*mp)->m_len, mtod((*mp), caddr_t));
len -= (*mp)->m_len;
mp = &(*mp)->m_next;
mlen = MLEN;
}
#endif
m_freem(m);
return m0;
}
static struct mbuf *
tulip_txput(
tulip_softc_t * const sc,
struct mbuf *m)
{
TULIP_PERFSTART(txput)
tulip_ringinfo_t * const ri = &sc->tulip_txinfo;
tulip_desc_t *eop, *nextout;
int segcnt, free;
u_int32_t d_status;
struct mbuf *m0;
#if defined(TULIP_DEBUG)
if ((sc->tulip_cmdmode & TULIP_CMD_TXRUN) == 0) {
printf(TULIP_PRINTF_FMT ": txput%s: tx not running\n",
TULIP_PRINTF_ARGS,
(sc->tulip_flags & TULIP_TXPROBE_ACTIVE) ? "(probe)" : "");
sc->tulip_flags |= TULIP_WANTTXSTART;
goto finish;
}
#endif
/*
* Now we try to fill in our transmit descriptors. This is
* a bit reminiscent of going on the Ark two by two
* since each descriptor for the TULIP can describe
* two buffers. So we advance through packet filling
* each of the two entries at a time to to fill each
* descriptor. Clear the first and last segment bits
* in each descriptor (actually just clear everything
* but the end-of-ring or chain bits) to make sure
* we don't get messed up by previously sent packets.
*
* We may fail to put the entire packet on the ring if
* there is either not enough ring entries free or if the
* packet has more than MAX_TXSEG segments. In the former
* case we will just wait for the ring to empty. In the
* latter case we have to recopy.
*/
again:
d_status = 0;
eop = nextout = ri->ri_nextout;
m0 = m;
segcnt = 0;
free = ri->ri_free;
do {
int len = m0->m_len;
caddr_t addr = mtod(m0, caddr_t);
unsigned clsize = CLBYTES - (((u_long) addr) & (CLBYTES-1));
while (len > 0) {
unsigned slen = min(len, clsize);
#ifdef BIG_PACKET
int partial = 0;
if (slen >= 2048)
slen = 2040, partial = 1;
#endif
segcnt++;
if (segcnt > TULIP_MAX_TXSEG) {
/*
* The packet exceeds the number of transmit buffer
* entries that we can use for one packet, so we have
* recopy it into one mbuf and then try again.
*/
m = tulip_mbuf_compress(m);
if (m == NULL)
goto finish;
goto again;
}
if (segcnt & 1) {
if (--free == 0) {
/*
* See if there's any unclaimed space in the
* transmit ring.
*/
if ((free += tulip_tx_intr(sc)) == 0) {
/*
* There's no more room but since nothing
* has been committed at this point, just
* show output is active, put back the
* mbuf and return.
*/
sc->tulip_flags |= TULIP_WANTTXSTART;
goto finish;
}
}
eop = nextout;
if (++nextout == ri->ri_last)
nextout = ri->ri_first;
eop->d_flag &= TULIP_DFLAG_ENDRING|TULIP_DFLAG_CHAIN;
eop->d_status = d_status;
eop->d_addr1 = TULIP_KVATOPHYS(sc, addr);
eop->d_length1 = slen;
} else {
/*
* Fill in second half of descriptor
*/
eop->d_addr2 = TULIP_KVATOPHYS(sc, addr);
eop->d_length2 = slen;
}
d_status = TULIP_DSTS_OWNER;
len -= slen;
addr += slen;
#ifdef BIG_PACKET
if (partial)
continue;
#endif
clsize = CLBYTES;
}
} while ((m0 = m0->m_next) != NULL);
/*
* The descriptors have been filled in. Now get ready
* to transmit.
*/
IF_ENQUEUE(&sc->tulip_txq, m);
m = NULL;
/*
* Make sure the next descriptor after this packet is owned
* by us since it may have been set up above if we ran out
* of room in the ring.
*/
nextout->d_status = 0;
/*
* If we only used the first segment of the last descriptor,
* make sure the second segment will not be used.
*/
if (segcnt & 1) {
eop->d_addr2 = 0;
eop->d_length2 = 0;
}
/*
* Mark the last and first segments, indicate we want a transmit
* complete interrupt, and tell it to transmit!
*/
eop->d_flag |= TULIP_DFLAG_TxLASTSEG|TULIP_DFLAG_TxWANTINTR;
/*
* Note that ri->ri_nextout is still the start of the packet
* and until we set the OWNER bit, we can still back out of
* everything we have done.
*/
ri->ri_nextout->d_flag |= TULIP_DFLAG_TxFIRSTSEG;
ri->ri_nextout->d_status = TULIP_DSTS_OWNER;
TULIP_CSR_WRITE(sc, csr_txpoll, 1);
/*
* This advances the ring for us.
*/
ri->ri_nextout = nextout;
ri->ri_free = free;
TULIP_PERFEND(txput);
if (sc->tulip_flags & TULIP_TXPROBE_ACTIVE) {
sc->tulip_if.if_flags |= IFF_OACTIVE;
TULIP_PERFEND(txput);
return NULL;
}
/*
* switch back to the single queueing ifstart.
*/
sc->tulip_flags &= ~TULIP_WANTTXSTART;
sc->tulip_if.if_start = tulip_ifstart_one;
if (sc->tulip_txtimer == 0)
sc->tulip_txtimer = TULIP_TXTIMER;
/*
* If we want a txstart, there must be not enough space in the
* transmit ring. So we want to enable transmit done interrupts
* so we can immediately reclaim some space. When the transmit
* interrupt is posted, the interrupt handler will call tx_intr
* to reclaim space and then txstart (since WANTTXSTART is set).
* txstart will move the packet into the transmit ring and clear
* WANTTXSTART thereby causing TXINTR to be cleared.
*/
finish:
if (sc->tulip_flags & (TULIP_WANTTXSTART|TULIP_DOINGSETUP)) {
sc->tulip_if.if_flags |= IFF_OACTIVE;
sc->tulip_if.if_start = tulip_ifstart;
if ((sc->tulip_intrmask & TULIP_STS_TXINTR) == 0) {
sc->tulip_intrmask |= TULIP_STS_TXINTR;
TULIP_CSR_WRITE(sc, csr_intr, sc->tulip_intrmask);
}
} else if ((sc->tulip_flags & TULIP_PROMISC) == 0) {
if (sc->tulip_intrmask & TULIP_STS_TXINTR) {
sc->tulip_intrmask &= ~TULIP_STS_TXINTR;
TULIP_CSR_WRITE(sc, csr_intr, sc->tulip_intrmask);
}
}
TULIP_PERFEND(txput);
return m;
}
static void
tulip_txput_setup(
tulip_softc_t * const sc)
{
tulip_ringinfo_t * const ri = &sc->tulip_txinfo;
tulip_desc_t *nextout;
/*
* We will transmit, at most, one setup packet per call to ifstart.
*/
#if defined(TULIP_DEBUG)
if ((sc->tulip_cmdmode & TULIP_CMD_TXRUN) == 0) {
printf(TULIP_PRINTF_FMT ": txput_setup: tx not running\n",
TULIP_PRINTF_ARGS);
sc->tulip_flags |= TULIP_WANTTXSTART;
sc->tulip_if.if_start = tulip_ifstart;
return;
}
#endif
/*
* Try to reclaim some free descriptors..
*/
if (ri->ri_free < 2)
tulip_tx_intr(sc);
if ((sc->tulip_flags & TULIP_DOINGSETUP) || ri->ri_free == 1) {
sc->tulip_flags |= TULIP_WANTTXSTART;
sc->tulip_if.if_start = tulip_ifstart;
return;
}
bcopy(sc->tulip_setupdata, sc->tulip_setupbuf,
sizeof(sc->tulip_setupbuf));
/*
* Clear WANTSETUP and set DOINGSETUP. Set know that WANTSETUP is
* set and DOINGSETUP is clear doing an XOR of the two will DTRT.
*/
sc->tulip_flags ^= TULIP_WANTSETUP|TULIP_DOINGSETUP;
ri->ri_free--;
nextout = ri->ri_nextout;
nextout->d_flag &= TULIP_DFLAG_ENDRING|TULIP_DFLAG_CHAIN;
nextout->d_flag |= TULIP_DFLAG_TxFIRSTSEG|TULIP_DFLAG_TxLASTSEG
|TULIP_DFLAG_TxSETUPPKT|TULIP_DFLAG_TxWANTINTR;
if (sc->tulip_flags & TULIP_WANTHASHPERFECT)
nextout->d_flag |= TULIP_DFLAG_TxHASHFILT;
else if (sc->tulip_flags & TULIP_WANTHASHONLY)
nextout->d_flag |= TULIP_DFLAG_TxHASHFILT|TULIP_DFLAG_TxINVRSFILT;
nextout->d_length1 = sizeof(sc->tulip_setupbuf);
nextout->d_addr1 = TULIP_KVATOPHYS(sc, sc->tulip_setupbuf);
nextout->d_length2 = 0;
nextout->d_addr2 = 0;
/*
* Advance the ring for the next transmit packet.
*/
if (++ri->ri_nextout == ri->ri_last)
ri->ri_nextout = ri->ri_first;
/*
* Make sure the next descriptor is owned by us since it
* may have been set up above if we ran out of room in the
* ring.
*/
ri->ri_nextout->d_status = 0;
nextout->d_status = TULIP_DSTS_OWNER;
TULIP_CSR_WRITE(sc, csr_txpoll, 1);
if ((sc->tulip_intrmask & TULIP_STS_TXINTR) == 0) {
sc->tulip_intrmask |= TULIP_STS_TXINTR;
TULIP_CSR_WRITE(sc, csr_intr, sc->tulip_intrmask);
}
}
/*
* This routine is entered at splnet() (splsoftnet() on NetBSD)
* and thereby imposes no problems when TULIP_USE_SOFTINTR is
* defined or not.
*/
static int
tulip_ifioctl(
struct ifnet * ifp,
ioctl_cmd_t cmd,
caddr_t data)
{
TULIP_PERFSTART(ifioctl)
tulip_softc_t * const sc = TULIP_IFP_TO_SOFTC(ifp);
struct ifaddr *ifa = (struct ifaddr *)data;
struct ifreq *ifr = (struct ifreq *) data;
tulip_spl_t s;
int error = 0;
#if defined(TULIP_USE_SOFTINTR)
s = TULIP_RAISESOFTSPL();
#else
s = TULIP_RAISESPL();
#endif
switch (cmd) {
case SIOCSIFADDR: {
ifp->if_flags |= IFF_UP;
switch(ifa->ifa_addr->sa_family) {
#ifdef INET
case AF_INET: {
tulip_init(sc);
TULIP_ARP_IFINIT(sc, ifa);
break;
}
#endif /* INET */
#ifdef NS
/*
* This magic copied from if_is.c; I don't use XNS,
* so I have no way of telling if this actually
* works or not.
*/
case AF_NS: {
struct ns_addr *ina = &(IA_SNS(ifa)->sns_addr);
if (ns_nullhost(*ina)) {
ina->x_host = *(union ns_host *)(sc->tulip_enaddr);
} else {
ifp->if_flags &= ~IFF_RUNNING;
bcopy((caddr_t)ina->x_host.c_host,
(caddr_t)sc->tulip_enaddr,
sizeof(sc->tulip_enaddr));
}
tulip_init(sc);
break;
}
#endif /* NS */
default: {
tulip_init(sc);
break;
}
}
break;
}
case SIOCGIFADDR: {
bcopy((caddr_t) sc->tulip_enaddr,
(caddr_t) ((struct sockaddr *)&ifr->ifr_data)->sa_data,
6);
break;
}
case SIOCSIFFLAGS: {
#if !defined(IFM_ETHER)
int flags = 0;
if (ifp->if_flags & IFF_LINK0) flags |= 1;
if (ifp->if_flags & IFF_LINK1) flags |= 2;
if (ifp->if_flags & IFF_LINK2) flags |= 4;
if (flags == 7) {
ifp->if_flags &= ~(IFF_LINK0|IFF_LINK1|IFF_LINK2);
sc->tulip_media = TULIP_MEDIA_UNKNOWN;
sc->tulip_probe_state = TULIP_PROBE_INACTIVE;
sc->tulip_flags &= ~(TULIP_WANTRXACT|TULIP_LINKUP|TULIP_NOAUTOSENSE);
tulip_reset(sc);
} else if (flags) {
tulip_media_t media;
for (media = TULIP_MEDIA_UNKNOWN; media < TULIP_MEDIA_MAX; media++) {
if (sc->tulip_mediums[media] != NULL && --flags == 0) {
sc->tulip_flags |= TULIP_NOAUTOSENSE;
if (sc->tulip_media != media || (sc->tulip_flags & TULIP_DIDNWAY)) {
sc->tulip_flags &= ~TULIP_DIDNWAY;
tulip_linkup(sc, media);
}
break;
}
}
if (flags)
printf(TULIP_PRINTF_FMT ": ignored invalid media request\n", TULIP_PRINTF_ARGS);
}
#endif
tulip_init(sc);
break;
}
#if defined(SIOCSIFMEDIA)
case SIOCSIFMEDIA:
case SIOCGIFMEDIA: {
error = ifmedia_ioctl(ifp, ifr, &sc->tulip_ifmedia, cmd);
break;
}
#endif
case SIOCADDMULTI:
case SIOCDELMULTI: {
/*
* Update multicast listeners
*/
#if defined(__FreeBSD__) && __FreeBSD__ >= 3
tulip_addr_filter(sc); /* reset multicast filtering */
tulip_init(sc);
error = 0;
#else
if (cmd == SIOCADDMULTI)
error = ether_addmulti(ifr, TULIP_ETHERCOM(sc));
else
error = ether_delmulti(ifr, TULIP_ETHERCOM(sc));
if (error == ENETRESET) {
tulip_addr_filter(sc); /* reset multicast filtering */
tulip_init(sc);
error = 0;
}
#endif
break;
}
#if defined(SIOCSIFMTU)
#if !defined(ifr_mtu)
#define ifr_mtu ifr_metric
#endif
case SIOCSIFMTU:
/*
* Set the interface MTU.
*/
if (ifr->ifr_mtu > ETHERMTU
#ifdef BIG_PACKET
&& sc->tulip_chipid != TULIP_21140
&& sc->tulip_chipid != TULIP_21140A
&& sc->tulip_chipid != TULIP_21041
#endif
) {
error = EINVAL;
break;
}
ifp->if_mtu = ifr->ifr_mtu;
#ifdef BIG_PACKET
tulip_reset(sc);
tulip_init(sc);
#endif
break;
#endif /* SIOCSIFMTU */
#ifdef SIOCGADDRROM
case SIOCGADDRROM: {
error = copyout(sc->tulip_rombuf, ifr->ifr_data, sizeof(sc->tulip_rombuf));
break;
}
#endif
#ifdef SIOCGCHIPID
case SIOCGCHIPID: {
ifr->ifr_metric = (int) sc->tulip_chipid;
break;
}
#endif
default: {
error = EINVAL;
break;
}
}
TULIP_RESTORESPL(s);
TULIP_PERFEND(ifioctl);
return error;
}
/*
* These routines gets called at device spl (from ether_output). This might
* pose a problem for TULIP_USE_SOFTINTR if ether_output is called at
* device spl from another driver.
*/
static ifnet_ret_t
tulip_ifstart(
struct ifnet * const ifp)
{
TULIP_PERFSTART(ifstart)
tulip_softc_t * const sc = TULIP_IFP_TO_SOFTC(ifp);
if (sc->tulip_if.if_flags & IFF_RUNNING) {
if ((sc->tulip_flags & (TULIP_WANTSETUP|TULIP_TXPROBE_ACTIVE)) == TULIP_WANTSETUP)
tulip_txput_setup(sc);
while (sc->tulip_if.if_snd.ifq_head != NULL) {
struct mbuf *m;
IF_DEQUEUE(&sc->tulip_if.if_snd, m);
if ((m = tulip_txput(sc, m)) != NULL) {
IF_PREPEND(&sc->tulip_if.if_snd, m);
break;
}
}
}
TULIP_PERFEND(ifstart);
}
static ifnet_ret_t
tulip_ifstart_one(
struct ifnet * const ifp)
{
TULIP_PERFSTART(ifstart_one)
tulip_softc_t * const sc = TULIP_IFP_TO_SOFTC(ifp);
if ((sc->tulip_if.if_flags & IFF_RUNNING)
&& sc->tulip_if.if_snd.ifq_head != NULL) {
struct mbuf *m;
IF_DEQUEUE(&sc->tulip_if.if_snd, m);
if ((m = tulip_txput(sc, m)) != NULL)
IF_PREPEND(&sc->tulip_if.if_snd, m);
}
TULIP_PERFEND(ifstart_one);
}
/*
* Even though this routine runs at device spl, it does not break
* our use of splnet (splsoftnet under NetBSD) for the majority
* of this driver (if TULIP_USE_SOFTINTR defined) since
* if_watcbog is called from if_watchdog which is called from
* splsoftclock which is below spl[soft]net.
*/
static void
tulip_ifwatchdog(
struct ifnet *ifp)
{
TULIP_PERFSTART(ifwatchdog)
tulip_softc_t * const sc = TULIP_IFP_TO_SOFTC(ifp);
#if defined(TULIP_DEBUG)
u_int32_t rxintrs = sc->tulip_dbg.dbg_rxintrs - sc->tulip_dbg.dbg_last_rxintrs;
if (rxintrs > sc->tulip_dbg.dbg_high_rxintrs_hz)
sc->tulip_dbg.dbg_high_rxintrs_hz = rxintrs;
sc->tulip_dbg.dbg_last_rxintrs = sc->tulip_dbg.dbg_rxintrs;
#endif /* TULIP_DEBUG */
sc->tulip_if.if_timer = 1;
/*
* These should be rare so do a bulk test up front so we can just skip
* them if needed.
*/
if (sc->tulip_flags & (TULIP_SYSTEMERROR|TULIP_RXBUFSLOW|TULIP_NOMESSAGES)) {
/*
* If the number of receive buffer is low, try to refill
*/
if (sc->tulip_flags & TULIP_RXBUFSLOW)
tulip_rx_intr(sc);
if (sc->tulip_flags & TULIP_SYSTEMERROR) {
printf(TULIP_PRINTF_FMT ": %d system errors: last was %s\n",
TULIP_PRINTF_ARGS, sc->tulip_system_errors,
tulip_system_errors[sc->tulip_last_system_error]);
}
if (sc->tulip_statusbits) {
tulip_print_abnormal_interrupt(sc, sc->tulip_statusbits);
sc->tulip_statusbits = 0;
}
sc->tulip_flags &= ~(TULIP_NOMESSAGES|TULIP_SYSTEMERROR);
}
if (sc->tulip_txtimer)
tulip_tx_intr(sc);
if (sc->tulip_txtimer && --sc->tulip_txtimer == 0) {
printf(TULIP_PRINTF_FMT ": transmission timeout\n", TULIP_PRINTF_ARGS);
if (TULIP_DO_AUTOSENSE(sc)) {
sc->tulip_media = TULIP_MEDIA_UNKNOWN;
sc->tulip_probe_state = TULIP_PROBE_INACTIVE;
sc->tulip_flags &= ~(TULIP_WANTRXACT|TULIP_LINKUP);
}
tulip_reset(sc);
tulip_init(sc);
}
TULIP_PERFEND(ifwatchdog);
TULIP_PERFMERGE(sc, perf_intr_cycles);
TULIP_PERFMERGE(sc, perf_ifstart_cycles);
TULIP_PERFMERGE(sc, perf_ifioctl_cycles);
TULIP_PERFMERGE(sc, perf_ifwatchdog_cycles);
TULIP_PERFMERGE(sc, perf_timeout_cycles);
TULIP_PERFMERGE(sc, perf_ifstart_one_cycles);
TULIP_PERFMERGE(sc, perf_txput_cycles);
TULIP_PERFMERGE(sc, perf_txintr_cycles);
TULIP_PERFMERGE(sc, perf_rxintr_cycles);
TULIP_PERFMERGE(sc, perf_rxget_cycles);
TULIP_PERFMERGE(sc, perf_intr);
TULIP_PERFMERGE(sc, perf_ifstart);
TULIP_PERFMERGE(sc, perf_ifioctl);
TULIP_PERFMERGE(sc, perf_ifwatchdog);
TULIP_PERFMERGE(sc, perf_timeout);
TULIP_PERFMERGE(sc, perf_ifstart_one);
TULIP_PERFMERGE(sc, perf_txput);
TULIP_PERFMERGE(sc, perf_txintr);
TULIP_PERFMERGE(sc, perf_rxintr);
TULIP_PERFMERGE(sc, perf_rxget);
}
#if defined(__bsdi__) || (defined(__FreeBSD__) && BSD < 199506)
static ifnet_ret_t
tulip_ifwatchdog_wrapper(
int unit)
{
tulip_ifwatchdog(&TULIP_UNIT_TO_SOFTC(unit)->tulip_if);
}
#define tulip_ifwatchdog tulip_ifwatchdog_wrapper
#endif
/*
* All printf's are real as of now!
*/
#ifdef printf
#undef printf
#endif
#if !defined(IFF_NOTRAILERS)
#define IFF_NOTRAILERS 0
#endif
static void
tulip_attach(
tulip_softc_t * const sc)
{
struct ifnet * const ifp = &sc->tulip_if;
ifp->if_flags = IFF_BROADCAST|IFF_SIMPLEX|IFF_NOTRAILERS|IFF_MULTICAST;
ifp->if_ioctl = tulip_ifioctl;
ifp->if_start = tulip_ifstart;
ifp->if_watchdog = tulip_ifwatchdog;
ifp->if_timer = 1;
#if !defined(__bsdi__) || _BSDI_VERSION < 199401
ifp->if_output = ether_output;
#endif
#if defined(__bsdi__) && _BSDI_VERSION < 199401
ifp->if_mtu = ETHERMTU;
#endif
#if defined(__bsdi__) && _BSDI_VERSION >= 199510
aprint_naive(": DEC Ethernet");
aprint_normal(": %s%s", sc->tulip_boardid,
tulip_chipdescs[sc->tulip_chipid]);
aprint_verbose(" pass %d.%d", (sc->tulip_revinfo & 0xF0) >> 4,
sc->tulip_revinfo & 0x0F);
printf("\n");
sc->tulip_pf = aprint_normal;
aprint_normal(TULIP_PRINTF_FMT ": address " TULIP_EADDR_FMT "\n",
TULIP_PRINTF_ARGS,
TULIP_EADDR_ARGS(sc->tulip_enaddr));
#else
printf(
#if defined(__bsdi__)
"\n"
#endif
TULIP_PRINTF_FMT ": %s%s pass %d.%d\n",
TULIP_PRINTF_ARGS,
sc->tulip_boardid,
tulip_chipdescs[sc->tulip_chipid],
(sc->tulip_revinfo & 0xF0) >> 4,
sc->tulip_revinfo & 0x0F);
printf(TULIP_PRINTF_FMT ": address " TULIP_EADDR_FMT "\n",
TULIP_PRINTF_ARGS,
TULIP_EADDR_ARGS(sc->tulip_enaddr));
#endif
#if defined(__alpha__)
/*
* In case the SRM console told us about a bogus media,
* we need to check to be safe.
*/
if (sc->tulip_mediums[sc->tulip_media] == NULL)
sc->tulip_media = TULIP_MEDIA_UNKNOWN;
#endif
(*sc->tulip_boardsw->bd_media_probe)(sc);
#if defined(IFM_ETHER)
ifmedia_init(&sc->tulip_ifmedia, 0,
tulip_ifmedia_change,
tulip_ifmedia_status);
#else
{
tulip_media_t media;
int cnt;
printf(TULIP_PRINTF_FMT ": media:", TULIP_PRINTF_ARGS);
for (media = TULIP_MEDIA_UNKNOWN, cnt = 1; cnt < 7 && media < TULIP_MEDIA_MAX; media++) {
if (sc->tulip_mediums[media] != NULL) {
printf(" %d=\"%s\"", cnt, tulip_mediums[media]);
cnt++;
}
}
if (cnt == 1) {
sc->tulip_features |= TULIP_HAVE_NOMEDIA;
printf(" none\n");
} else {
printf("\n");
}
}
#endif
sc->tulip_flags &= ~TULIP_DEVICEPROBE;
#if defined(IFM_ETHER)
tulip_ifmedia_add(sc);
#endif
tulip_reset(sc);
#if defined(__bsdi__) && _BSDI_VERSION >= 199510
sc->tulip_pf = printf;
TULIP_ETHER_IFATTACH(sc);
#else
if_attach(ifp);
#if defined(__NetBSD__) || (defined(__FreeBSD__) && BSD >= 199506)
TULIP_ETHER_IFATTACH(sc);
#endif
#endif /* __bsdi__ */
#if NBPFILTER > 0
TULIP_BPF_ATTACH(sc);
#endif
}
static void
tulip_initcsrs(
tulip_softc_t * const sc,
tulip_csrptr_t csr_base,
size_t csr_size)
{
sc->tulip_csrs.csr_busmode = csr_base + 0 * csr_size;
sc->tulip_csrs.csr_txpoll = csr_base + 1 * csr_size;
sc->tulip_csrs.csr_rxpoll = csr_base + 2 * csr_size;
sc->tulip_csrs.csr_rxlist = csr_base + 3 * csr_size;
sc->tulip_csrs.csr_txlist = csr_base + 4 * csr_size;
sc->tulip_csrs.csr_status = csr_base + 5 * csr_size;
sc->tulip_csrs.csr_command = csr_base + 6 * csr_size;
sc->tulip_csrs.csr_intr = csr_base + 7 * csr_size;
sc->tulip_csrs.csr_missed_frames = csr_base + 8 * csr_size;
sc->tulip_csrs.csr_9 = csr_base + 9 * csr_size;
sc->tulip_csrs.csr_10 = csr_base + 10 * csr_size;
sc->tulip_csrs.csr_11 = csr_base + 11 * csr_size;
sc->tulip_csrs.csr_12 = csr_base + 12 * csr_size;
sc->tulip_csrs.csr_13 = csr_base + 13 * csr_size;
sc->tulip_csrs.csr_14 = csr_base + 14 * csr_size;
sc->tulip_csrs.csr_15 = csr_base + 15 * csr_size;
#if defined(TULIP_EISA)
sc->tulip_csrs.csr_enetrom = csr_base + DE425_ENETROM_OFFSET;
#endif
}
static void
tulip_initring(
tulip_softc_t * const sc,
tulip_ringinfo_t * const ri,
tulip_desc_t *descs,
int ndescs)
{
ri->ri_max = ndescs;
ri->ri_first = descs;
ri->ri_last = ri->ri_first + ri->ri_max;
bzero((caddr_t) ri->ri_first, sizeof(ri->ri_first[0]) * ri->ri_max);
ri->ri_last[-1].d_flag = TULIP_DFLAG_ENDRING;
}
/*
* This is the PCI configuration support. Since the 21040 is available
* on both EISA and PCI boards, one must be careful in how defines the
* 21040 in the config file.
*/
#define PCI_CFID 0x00 /* Configuration ID */
#define PCI_CFCS 0x04 /* Configurtion Command/Status */
#define PCI_CFRV 0x08 /* Configuration Revision */
#define PCI_CFLT 0x0c /* Configuration Latency Timer */
#define PCI_CBIO 0x10 /* Configuration Base IO Address */
#define PCI_CBMA 0x14 /* Configuration Base Memory Address */
#define PCI_CFIT 0x3c /* Configuration Interrupt */
#define PCI_CFDA 0x40 /* Configuration Driver Area */
#if defined(TULIP_EISA)
static const int tulip_eisa_irqs[4] = { IRQ5, IRQ9, IRQ10, IRQ11 };
#endif
#if defined(__FreeBSD__)
#define TULIP_PCI_ATTACH_ARGS pcici_t config_id, int unit
#define TULIP_SHUTDOWN_ARGS int howto, void * arg
#if defined(TULIP_DEVCONF)
static void tulip_shutdown(TULIP_SHUTDOWN_ARGS);
static int
tulip_pci_shutdown(
struct kern_devconf * const kdc,
int force)
{
if (kdc->kdc_unit < TULIP_MAX_DEVICES) {
tulip_softc_t * const sc = TULIP_UNIT_TO_SOFTC(kdc->kdc_unit);
if (sc != NULL)
tulip_shutdown(0, sc);
}
(void) dev_detach(kdc);
return 0;
}
#endif
static char*
tulip_pci_probe(
pcici_t config_id,
pcidi_t device_id)
{
if (PCI_VENDORID(device_id) != DEC_VENDORID)
return NULL;
if (PCI_CHIPID(device_id) == CHIPID_21040)
return "Digital 21040 Ethernet";
if (PCI_CHIPID(device_id) == CHIPID_21041)
return "Digital 21041 Ethernet";
if (PCI_CHIPID(device_id) == CHIPID_21140) {
u_int32_t revinfo = pci_conf_read(config_id, PCI_CFRV) & 0xFF;
if (revinfo >= 0x20)
return "Digital 21140A Fast Ethernet";
else
return "Digital 21140 Fast Ethernet";
}
if (PCI_CHIPID(device_id) == CHIPID_21142) {
u_int32_t revinfo = pci_conf_read(config_id, PCI_CFRV) & 0xFF;
if (revinfo >= 0x20)
return "Digital 21143 Fast Ethernet";
else
return "Digital 21142 Fast Ethernet";
}
return NULL;
}
static void tulip_pci_attach(TULIP_PCI_ATTACH_ARGS);
static u_long tulip_pci_count;
struct pci_device dedevice = {
"de",
tulip_pci_probe,
tulip_pci_attach,
&tulip_pci_count,
#if defined(TULIP_DEVCONF)
tulip_pci_shutdown,
#endif
};
DATA_SET (pcidevice_set, dedevice);
#endif /* __FreeBSD__ */
#if defined(__bsdi__)
#define TULIP_PCI_ATTACH_ARGS struct device * const parent, struct device * const self, void * const aux
#define TULIP_SHUTDOWN_ARGS void *arg
static int
tulip_pci_match(
pci_devaddr_t *pa)
{
int irq;
unsigned id;
id = pci_inl(pa, PCI_VENDOR_ID);
if (PCI_VENDORID(id) != DEC_VENDORID)
return 0;
id = PCI_CHIPID(id);
if (id != CHIPID_21040 && id != CHIPID_21041
&& id != CHIPID_21140 && id != CHIPID_21142)
return 0;
irq = pci_inl(pa, PCI_I_LINE) & 0xFF;
if (irq == 0 || irq >= 16) {
printf("de?: invalid IRQ %d; skipping\n", irq);
return 0;
}
return 1;
}
static int
tulip_probe(
struct device *parent,
struct cfdata *cf,
void *aux)
{
struct isa_attach_args * const ia = (struct isa_attach_args *) aux;
unsigned irq, slot;
pci_devaddr_t *pa;
#if _BSDI_VERSION >= 199401
switch (ia->ia_bustype) {
case BUS_PCI:
#endif
pa = pci_scan(tulip_pci_match);
if (pa == NULL)
return 0;
irq = (1 << (pci_inl(pa, PCI_I_LINE) & 0xFF));
/* Get the base address; assume the BIOS set it up correctly */
#if defined(TULIP_IOMAPPED)
ia->ia_maddr = NULL;
ia->ia_msize = 0;
ia->ia_iobase = pci_inl(pa, PCI_CBIO) & ~7;
pci_outl(pa, PCI_CBIO, 0xFFFFFFFF);
ia->ia_iosize = ((~pci_inl(pa, PCI_CBIO)) | 7) + 1;
pci_outl(pa, PCI_CBIO, (int) ia->ia_iobase);
/* Disable memory space access */
pci_outl(pa, PCI_COMMAND, pci_inl(pa, PCI_COMMAND) & ~2);
#else
ia->ia_maddr = (caddr_t) (pci_inl(pa, PCI_CBMA) & ~7);
pci_outl(pa, PCI_CBMA, 0xFFFFFFFF);
ia->ia_msize = ((~pci_inl(pa, PCI_CBMA)) | 7) + 1;
pci_outl(pa, PCI_CBMA, (int) ia->ia_maddr);
ia->ia_iobase = 0;
ia->ia_iosize = 0;
/* Disable I/O space access */
pci_outl(pa, PCI_COMMAND, pci_inl(pa, PCI_COMMAND) & ~1);
#endif /* TULIP_IOMAPPED */
ia->ia_aux = (void *) pa;
#if _BSDI_VERSION >= 199401
break;
#if defined(TULIP_EISA)
case BUS_EISA: {
unsigned tmp;
if ((slot = eisa_match(cf, ia)) == 0)
return 0;
ia->ia_iobase = slot << 12;
ia->ia_iosize = EISA_NPORT;
eisa_slotalloc(slot);
tmp = inb(ia->ia_iobase + DE425_CFG0);
irq = tulip_eisa_irqs[(tmp >> 1) & 0x03];
/*
* Until BSD/OS likes level interrupts, force
* the DE425 into edge-triggered mode.
*/
if ((tmp & 1) == 0)
outb(ia->ia_iobase + DE425_CFG0, tmp | 1);
/*
* CBIO needs to map to the EISA slot
* enable I/O access and Master
*/
outl(ia->ia_iobase + DE425_CBIO, ia->ia_iobase);
outl(ia->ia_iobase + DE425_CFCS, 5 | inl(ia->ia_iobase + DE425_CFCS));
ia->ia_aux = NULL;
break;
}
#endif /* TULIP_EISA */
default:
return 0;
}
#endif
/* PCI bus masters don't use host DMA channels */
ia->ia_drq = DRQNONE;
if (ia->ia_irq != IRQUNK && irq != ia->ia_irq) {
printf("de%d: error: desired IRQ of %d does not match device's "
"actual IRQ of %d,\n",
cf->cf_unit,
ffs(ia->ia_irq) - 1, ffs(irq) - 1);
return 0;
}
if (ia->ia_irq == IRQUNK)
ia->ia_irq = irq;
#ifdef IRQSHARE
ia->ia_irq |= IRQSHARE;
#endif
return 1;
}
static void tulip_pci_attach(TULIP_PCI_ATTACH_ARGS);
#if defined(TULIP_EISA)
static char *tulip_eisa_ids[] = {
"DEC4250",
NULL
};
#endif
struct cfdriver decd = {
0, "de", tulip_probe, tulip_pci_attach,
#if _BSDI_VERSION >= 199401
DV_IFNET,
#endif
sizeof(tulip_softc_t),
#if defined(TULIP_EISA)
tulip_eisa_ids
#endif
};
#endif /* __bsdi__ */
#if defined(__NetBSD__)
#define TULIP_PCI_ATTACH_ARGS struct device * const parent, struct device * const self, void * const aux
#define TULIP_SHUTDOWN_ARGS void *arg
static int
tulip_pci_probe(
struct device *parent,
#ifdef __BROKEN_INDIRECT_CONFIG
void *match,
#else
struct cfdata *match,
#endif
void *aux)
{
struct pci_attach_args *pa = (struct pci_attach_args *) aux;
if (PCI_VENDORID(pa->pa_id) != DEC_VENDORID)
return 0;
if (PCI_CHIPID(pa->pa_id) == CHIPID_21040
|| PCI_CHIPID(pa->pa_id) == CHIPID_21041
|| PCI_CHIPID(pa->pa_id) == CHIPID_21140
|| PCI_CHIPID(pa->pa_id) == CHIPID_21142)
return 1;
return 0;
}
static void tulip_pci_attach(TULIP_PCI_ATTACH_ARGS);
struct cfattach de_ca = {
sizeof(tulip_softc_t), tulip_pci_probe, tulip_pci_attach
};
struct cfdriver de_cd = {
0, "de", DV_IFNET
};
#endif /* __NetBSD__ */
static void
tulip_shutdown(
TULIP_SHUTDOWN_ARGS)
{
tulip_softc_t * const sc = arg;
TULIP_CSR_WRITE(sc, csr_busmode, TULIP_BUSMODE_SWRESET);
DELAY(10); /* Wait 10 microseconds (actually 50 PCI cycles but at
33MHz that comes to two microseconds but wait a
bit longer anyways) */
}
static void
tulip_pci_attach(
TULIP_PCI_ATTACH_ARGS)
{
#if defined(__FreeBSD__)
tulip_softc_t *sc;
#define PCI_CONF_WRITE(r, v) pci_conf_write(config_id, (r), (v))
#define PCI_CONF_READ(r) pci_conf_read(config_id, (r))
#if __FreeBSD__ >= 3
#define PCI_GETBUSDEVINFO(sc) ((void)((sc)->tulip_pci_busno = (config_id->bus), /* XXX */ \
(sc)->tulip_pci_devno = (config_id->slot))) /* XXX */
#else
#define PCI_GETBUSDEVINFO(sc) ((void)((sc)->tulip_pci_busno = ((config_id.cfg1 >> 16) & 0xFF), /* XXX */ \
(sc)->tulip_pci_devno = ((config_id.cfg1 >> 11) & 0x1F))) /* XXX */
#endif
#endif
#if defined(__bsdi__)
tulip_softc_t * const sc = (tulip_softc_t *) self;
struct isa_attach_args * const ia = (struct isa_attach_args *) aux;
pci_devaddr_t *pa = (pci_devaddr_t *) ia->ia_aux;
const int unit = sc->tulip_dev.dv_unit;
#define PCI_CONF_WRITE(r, v) pci_outl(pa, (r), (v))
#define PCI_CONF_READ(r) pci_inl(pa, (r))
#define PCI_GETBUSDEVINFO(sc) ((void)((sc)->tulip_pci_busno = pa->d_bus, \
(sc)->tulip_pci_devno = pa->d_agent))
#endif
#if defined(__NetBSD__)
tulip_softc_t * const sc = (tulip_softc_t *) self;
struct pci_attach_args * const pa = (struct pci_attach_args *) aux;
const int unit = sc->tulip_dev.dv_unit;
#define PCI_CONF_WRITE(r, v) pci_conf_write(pa->pa_pc, pa->pa_tag, (r), (v))
#define PCI_CONF_READ(r) pci_conf_read(pa->pa_pc, pa->pa_tag, (r))
#define PCI_GETBUSDEVINFO(sc) do { \
(sc)->tulip_pci_busno = parent; \
(sc)->tulip_pci_devno = pa->pa_device; \
} while (0)
#endif /* __NetBSD__ */
int retval, idx;
u_int32_t revinfo, cfdainfo, id;
#if !defined(TULIP_IOMAPPED) && defined(__FreeBSD__)
vm_offset_t pa_csrs;
#endif
unsigned csroffset = TULIP_PCI_CSROFFSET;
unsigned csrsize = TULIP_PCI_CSRSIZE;
tulip_csrptr_t csr_base;
tulip_chipid_t chipid = TULIP_CHIPID_UNKNOWN;
if (unit >= TULIP_MAX_DEVICES) {
#ifdef __FreeBSD__
printf("de%d", unit);
#endif
printf(": not configured; limit of %d reached or exceeded\n",
TULIP_MAX_DEVICES);
return;
}
#if defined(__bsdi__)
if (pa != NULL) {
revinfo = pci_inl(pa, PCI_CFRV) & 0xFF;
id = pci_inl(pa, PCI_CFID);
cfdainfo = pci_inl(pa, PCI_CFDA);
#if defined(TULIP_EISA)
} else {
revinfo = inl(ia->ia_iobase + DE425_CFRV) & 0xFF;
csroffset = TULIP_EISA_CSROFFSET;
csrsize = TULIP_EISA_CSRSIZE;
chipid = TULIP_DE425;
cfdainfo = 0;
#endif /* TULIP_EISA */
}
#else /* __bsdi__ */
revinfo = PCI_CONF_READ(PCI_CFRV) & 0xFF;
id = PCI_CONF_READ(PCI_CFID);
cfdainfo = PCI_CONF_READ(PCI_CFDA);
#endif /* __bsdi__ */
if (PCI_VENDORID(id) == DEC_VENDORID) {
if (PCI_CHIPID(id) == CHIPID_21040) chipid = TULIP_21040;
else if (PCI_CHIPID(id) == CHIPID_21140) {
chipid = (revinfo >= 0x20) ? TULIP_21140A : TULIP_21140;
} else if (PCI_CHIPID(id) == CHIPID_21142) {
chipid = (revinfo >= 0x20) ? TULIP_21143 : TULIP_21142;
}
else if (PCI_CHIPID(id) == CHIPID_21041) chipid = TULIP_21041;
else if (PCI_CHIPID(id) == CHIPID_21142) chipid = TULIP_21142;
}
if (chipid == TULIP_CHIPID_UNKNOWN)
return;
if ((chipid == TULIP_21040 || chipid == TULIP_DE425) && revinfo < 0x20) {
#ifdef __FreeBSD__
printf("de%d", unit);
#endif
printf(": not configured; 21040 pass 2.0 required (%d.%d found)\n",
revinfo >> 4, revinfo & 0x0f);
return;
} else if (chipid == TULIP_21140 && revinfo < 0x11) {
#ifndef __FreeBSD__
printf("\n");
#endif
printf("de%d: not configured; 21140 pass 1.1 required (%d.%d found)\n",
unit, revinfo >> 4, revinfo & 0x0f);
return;
}
#if defined(__FreeBSD__)
sc = (tulip_softc_t *) malloc(sizeof(*sc), M_DEVBUF, M_NOWAIT);
if (sc == NULL)
return;
bzero(sc, sizeof(*sc)); /* Zero out the softc*/
sc->tulip_rxdescs = (tulip_desc_t *) malloc(sizeof(tulip_desc_t) * TULIP_RXDESCS, M_DEVBUF, M_NOWAIT);
sc->tulip_txdescs = (tulip_desc_t *) malloc(sizeof(tulip_desc_t) * TULIP_TXDESCS, M_DEVBUF, M_NOWAIT);
if (sc->tulip_rxdescs == NULL || sc->tulip_txdescs == NULL) {
if (sc->tulip_rxdescs)
free((caddr_t) sc->tulip_rxdescs, M_DEVBUF);
if (sc->tulip_rxdescs)
free((caddr_t) sc->tulip_rxdescs, M_DEVBUF);
free((caddr_t) sc, M_DEVBUF);
return;
}
#endif
PCI_GETBUSDEVINFO(sc);
sc->tulip_chipid = chipid;
sc->tulip_flags |= TULIP_DEVICEPROBE;
if (chipid == TULIP_21140 || chipid == TULIP_21140A)
sc->tulip_features |= TULIP_HAVE_GPR|TULIP_HAVE_STOREFWD;
if (chipid == TULIP_21140A && revinfo <= 0x22)
sc->tulip_features |= TULIP_HAVE_RXBADOVRFLW;
if (chipid == TULIP_21140)
sc->tulip_features |= TULIP_HAVE_BROKEN_HASH;
if (chipid != TULIP_21040 && chipid != TULIP_DE425 && chipid != TULIP_21140)
sc->tulip_features |= TULIP_HAVE_POWERMGMT;
if (chipid == TULIP_21041 || chipid == TULIP_21142 || chipid == TULIP_21143) {
sc->tulip_features |= TULIP_HAVE_DUALSENSE;
if (chipid != TULIP_21041 || sc->tulip_revinfo >= 0x20)
sc->tulip_features |= TULIP_HAVE_SIANWAY;
if (chipid != TULIP_21041)
sc->tulip_features |= TULIP_HAVE_SIAGP|TULIP_HAVE_RXBADOVRFLW|TULIP_HAVE_STOREFWD;
}
if (sc->tulip_features & TULIP_HAVE_POWERMGMT
&& (cfdainfo & (TULIP_CFDA_SLEEP|TULIP_CFDA_SNOOZE))) {
cfdainfo &= ~(TULIP_CFDA_SLEEP|TULIP_CFDA_SNOOZE);
PCI_CONF_WRITE(PCI_CFDA, cfdainfo);
DELAY(11*1000);
}
#if defined(__alpha__)
/*
* The Alpha SRM console encodes a console set media in the driver
* part of the CFDA register. Note that the Multia presents a
* problem in that its BNC mode is really EXTSIA. So in that case
* force a probe.
*/
switch ((cfdainfo >> 8) & 0xff) {
case 1: sc->tulip_media = chipid > TULIP_DE425 ? TULIP_MEDIA_AUI : TULIP_MEDIA_AUIBNC;
case 2: sc->tulip_media = chipid > TULIP_DE425 ? TULIP_MEDIA_BNC : TULIP_MEDIA_UNKNOWN;
case 3: sc->tulip_media = TULIP_MEDIA_10BASET;
case 4: sc->tulip_media = TULIP_MEDIA_10BASET_FD;
case 5: sc->tulip_media = TULIP_MEDIA_100BASETX;
case 6: sc->tulip_media = TULIP_MEDIA_100BASETX_FD;
}
#endif
#if defined(__NetBSD__)
bcopy(self->dv_xname, sc->tulip_if.if_xname, IFNAMSIZ);
sc->tulip_if.if_softc = sc;
sc->tulip_pc = pa->pa_pc;
#else
sc->tulip_unit = unit;
sc->tulip_name = "de";
#endif
sc->tulip_revinfo = revinfo;
#if defined(__FreeBSD__)
#if BSD >= 199506
sc->tulip_if.if_softc = sc;
#endif
#if defined(TULIP_IOMAPPED)
retval = pci_map_port(config_id, PCI_CBIO, &csr_base);
#else
retval = pci_map_mem(config_id, PCI_CBMA, (vm_offset_t *) &csr_base, &pa_csrs);
#endif
if (!retval) {
free((caddr_t) sc, M_DEVBUF);
return;
}
tulips[unit] = sc;
#endif /* __FreeBSD__ */
#if defined(__bsdi__)
sc->tulip_pf = printf;
#if defined(TULIP_IOMAPPED)
csr_base = ia->ia_iobase;
#else
csr_base = (vm_offset_t) mapphys((vm_offset_t) ia->ia_maddr, ia->ia_msize);
#endif
#endif /* __bsdi__ */
#if defined(__NetBSD__)
csr_base = 0;
{
bus_space_tag_t iot, memt;
bus_space_handle_t ioh, memh;
u_int32_t cfcs = PCI_CONF_READ(PCI_CFCS);
cfcs &= ~(PCI_COMMAND_IO_ENABLE||PCI_COMMAND_IO_ENABLE);
if (!pci_mapreg_map(pa, PCI_CBIO, PCI_MAPREG_TYPE_IO, 0,
&iot, &ioh, NULL, NULL)) {
cfcs |= PCI_COMMAND_IO_ENABLE;
}
if (!pci_mapreg_map(pa, PCI_CBMA,
PCI_MAPREG_TYPE_MEM | PCI_MAPREG_MEM_TYPE_32BIT,
0, &memt, &memh, NULL, NULL) == 0) {
cfcs |= PCI_COMMAND_MEM_ENABLE;
}
if ((cfcs & (PCI_COMMAND_IO_ENABLE||PCI_COMMAND_IO_ENABLE)) == 0) {
printf(": unable to map device registers\n");
return;
}
cfcs |= PCI_COMMAND_MASTER_ENABLE;
PCI_CONF_WRITE(PCI_CFCS, cfcs);
#if defined(PCI_PREFER_IOSPACE)
if (cfcs & PCI_COMMAND_IO_ENABLE) {
sc->tulip_bustag = iot, sc->tulip_bushandle = ioh;
} else {
sc->tulip_bustag = memt, sc->tulip_bushandle = memh;
}
#else
if (cfcs & PCI_COMMAND_MEM_ENABLE) {
sc->tulip_bustag = memt, sc->tulip_bushandle = memh;
} else {
sc->tulip_bustag = iot, sc->tulip_bushandle = ioh;
}
#endif /* PCI_PREFER_IOSPACE */
}
#endif /* __NetBSD__ */
tulip_initcsrs(sc, csr_base + csroffset, csrsize);
tulip_initring(sc, &sc->tulip_rxinfo, sc->tulip_rxdescs, TULIP_RXDESCS);
tulip_initring(sc, &sc->tulip_txinfo, sc->tulip_txdescs, TULIP_TXDESCS);
/*
* Make sure there won't be any interrupts or such...
*/
TULIP_CSR_WRITE(sc, csr_busmode, TULIP_BUSMODE_SWRESET);
DELAY(100); /* Wait 10 microseconds (actually 50 PCI cycles but at
33MHz that comes to two microseconds but wait a
bit longer anyways) */
if ((retval = tulip_read_macaddr(sc)) < 0) {
#if defined(__FreeBSD__)
printf(TULIP_PRINTF_FMT, TULIP_PRINTF_ARGS);
#endif
printf(": can't read ENET ROM (why=%d) (", retval);
for (idx = 0; idx < 32; idx++)
printf("%02x", sc->tulip_rombuf[idx]);
printf("\n");
printf(TULIP_PRINTF_FMT ": %s%s pass %d.%d\n",
TULIP_PRINTF_ARGS,
sc->tulip_boardid, tulip_chipdescs[sc->tulip_chipid],
(sc->tulip_revinfo & 0xF0) >> 4, sc->tulip_revinfo & 0x0F);
printf(TULIP_PRINTF_FMT ": address unknown\n", TULIP_PRINTF_ARGS);
} else {
tulip_spl_t s;
tulip_intrfunc_t (*intr_rtn)(void *) = tulip_intr_normal;
if (sc->tulip_features & TULIP_HAVE_SHAREDINTR)
intr_rtn = tulip_intr_shared;
#if defined(__NetBSD__)
if ((sc->tulip_features & TULIP_HAVE_SLAVEDINTR) == 0) {
pci_intr_handle_t intrhandle;
const char *intrstr;
if (pci_intr_map(pa->pa_pc, pa->pa_intrtag, pa->pa_intrpin,
pa->pa_intrline, &intrhandle)) {
printf(": couldn't map interrupt\n");
return;
}
intrstr = pci_intr_string(pa->pa_pc, intrhandle);
sc->tulip_ih = pci_intr_establish(pa->pa_pc, intrhandle, IPL_NET,
intr_rtn, sc);
if (sc->tulip_ih == NULL)
printf(": couldn't establish interrupt");
if (intrstr != NULL)
printf(" at %s", intrstr);
printf("\n");
if (sc->tulip_ih == NULL)
return;
}
sc->tulip_ats = shutdownhook_establish(tulip_shutdown, sc);
if (sc->tulip_ats == NULL)
printf("\n%s: warning: couldn't establish shutdown hook\n",
sc->tulip_xname);
#endif
#if defined(__FreeBSD__)
if ((sc->tulip_features & TULIP_HAVE_SLAVEDINTR) == 0) {
if (!pci_map_int (config_id, intr_rtn, (void*) sc, &net_imask)) {
printf(TULIP_PRINTF_FMT ": couldn't map interrupt\n",
TULIP_PRINTF_ARGS);
return;
}
}
#if !defined(TULIP_DEVCONF)
at_shutdown(tulip_shutdown, sc, SHUTDOWN_POST_SYNC);
#endif
#endif
#if defined(__bsdi__)
if ((sc->tulip_features & TULIP_HAVE_SLAVEDINTR) == 0) {
isa_establish(&sc->tulip_id, &sc->tulip_dev);
sc->tulip_ih.ih_fun = intr_rtn;
sc->tulip_ih.ih_arg = (void *) sc;
intr_establish(ia->ia_irq, &sc->tulip_ih, DV_NET);
}
sc->tulip_ats.func = tulip_shutdown;
sc->tulip_ats.arg = (void *) sc;
atshutdown(&sc->tulip_ats, ATSH_ADD);
#endif
#if defined(TULIP_USE_SOFTINTR)
if (sc->tulip_unit > tulip_softintr_max_unit)
tulip_softintr_max_unit = sc->tulip_unit;
#endif
s = TULIP_RAISESPL();
tulip_reset(sc);
tulip_attach(sc);
TULIP_RESTORESPL(s);
}
}